Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 65.1 >
edited by Xiaoling
on 2022/07/08 14:59
To version < 66.1 >
edited by Xiaoling
on 2022/07/08 17:00
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -13,11 +13,14 @@
13 13  
14 14  **Table of Contents:**
15 15  
16 +{{toc/}}
16 16  
17 17  
18 18  
19 19  
20 20  
22 +
23 +
21 21  = 1.  Introduction =
22 22  
23 23  == 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
... ... @@ -25,13 +25,21 @@
25 25  (((
26 26  
27 27  
31 +(((
28 28  Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
33 +)))
29 29  
35 +(((
30 30  It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
37 +)))
31 31  
39 +(((
32 32  The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
41 +)))
33 33  
43 +(((
34 34  NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
45 +)))
35 35  
36 36  
37 37  )))
... ... @@ -43,9 +43,8 @@
43 43  
44 44  
45 45  
46 -== 1.2 ​Features ==
57 +== 1.2 ​ Features ==
47 47  
48 -
49 49  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
50 50  * Monitor Soil Moisture
51 51  * Monitor Soil Temperature
... ... @@ -59,6 +59,9 @@
59 59  * Micro SIM card slot for NB-IoT SIM
60 60  * 8500mAh Battery for long term use
61 61  
72 +
73 +
74 +
62 62  == 1.3  Specification ==
63 63  
64 64  
... ... @@ -76,7 +76,7 @@
76 76  * - B20 @H-FDD: 800MHz
77 77  * - B28 @H-FDD: 700MHz
78 78  
79 -(% style="color:#037691" %)**Probe Specification:**
92 +Probe(% style="color:#037691" %)** Specification:**
80 80  
81 81  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
82 82  
... ... @@ -126,7 +126,9 @@
126 126  === 2.2.1 Test Requirement ===
127 127  
128 128  
142 +(((
129 129  To use NSE01 in your city, make sure meet below requirements:
144 +)))
130 130  
131 131  * Your local operator has already distributed a NB-IoT Network there.
132 132  * The local NB-IoT network used the band that NSE01 supports.
... ... @@ -143,9 +143,13 @@
143 143  
144 144  === 2.2.2 Insert SIM card ===
145 145  
161 +(((
146 146  Insert the NB-IoT Card get from your provider.
163 +)))
147 147  
165 +(((
148 148  User need to take out the NB-IoT module and insert the SIM card like below:
167 +)))
149 149  
150 150  
151 151  [[image:1657249468462-536.png]]
... ... @@ -184,7 +184,9 @@
184 184  
185 185  [[image:image-20220708110657-3.png]]
186 186  
206 +(((
187 187  (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
208 +)))
188 188  
189 189  
190 190  
... ... @@ -287,12 +287,14 @@
287 287  In this mode, uplink payload includes in total 18 bytes
288 288  
289 289  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
290 -|=(% style="width: 50px;" %)(((
311 +|=(% style="width: 60px;" %)(((
291 291  **Size(bytes)**
292 -)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
293 -|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
313 +)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
314 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
294 294  
316 +(((
295 295  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
318 +)))
296 296  
297 297  
298 298  [[image:image-20220708111918-4.png]]
... ... @@ -312,28 +312,45 @@
312 312  * Soil Conductivity(EC) = 0x02f9 =761 uS /cm
313 313  * Interrupt: 0x00 = 0
314 314  
338 +
339 +
340 +
315 315  == 2.4  Payload Explanation and Sensor Interface ==
316 316  
317 317  
318 318  === 2.4.1  Device ID ===
319 319  
346 +(((
320 320  By default, the Device ID equal to the last 6 bytes of IMEI.
348 +)))
321 321  
350 +(((
322 322  User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
352 +)))
323 323  
354 +(((
324 324  **Example:**
356 +)))
325 325  
358 +(((
326 326  AT+DEUI=A84041F15612
360 +)))
327 327  
362 +(((
328 328  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
364 +)))
329 329  
330 330  
331 331  
332 332  === 2.4.2  Version Info ===
333 333  
370 +(((
334 334  Specify the software version: 0x64=100, means firmware version 1.00.
372 +)))
335 335  
374 +(((
336 336  For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
376 +)))
337 337  
338 338  
339 339  
... ... @@ -355,19 +355,33 @@
355 355  
356 356  === 2.4.4  Signal Strength ===
357 357  
398 +(((
358 358  NB-IoT Network signal Strength.
400 +)))
359 359  
402 +(((
360 360  **Ex1: 0x1d = 29**
404 +)))
361 361  
406 +(((
362 362  (% style="color:blue" %)**0**(%%)  -113dBm or less
408 +)))
363 363  
410 +(((
364 364  (% style="color:blue" %)**1**(%%)  -111dBm
412 +)))
365 365  
414 +(((
366 366  (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
416 +)))
367 367  
418 +(((
368 368  (% style="color:blue" %)**31**  (%%) -51dBm or greater
420 +)))
369 369  
422 +(((
370 370  (% style="color:blue" %)**99**   (%%) Not known or not detectable
424 +)))
371 371  
372 372  
373 373  
... ... @@ -374,12 +374,16 @@
374 374  === 2.4.5  Soil Moisture ===
375 375  
376 376  (((
431 +(((
377 377  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
378 378  )))
434 +)))
379 379  
380 380  (((
437 +(((
381 381  For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
382 382  )))
440 +)))
383 383  
384 384  (((
385 385  
... ... @@ -394,7 +394,7 @@
394 394  === 2.4.6  Soil Temperature ===
395 395  
396 396  (((
397 - Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
455 +Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
398 398  )))
399 399  
400 400  (((
... ... @@ -435,34 +435,56 @@
435 435  
436 436  === 2.4.8  Digital Interrupt ===
437 437  
496 +(((
438 438  Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
498 +)))
439 439  
500 +(((
440 440  The command is:
502 +)))
441 441  
504 +(((
442 442  (% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
506 +)))
443 443  
444 444  
445 -The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
509 +(((
510 +The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
511 +)))
446 446  
447 447  
514 +(((
448 448  Example:
516 +)))
449 449  
518 +(((
450 450  0x(00): Normal uplink packet.
520 +)))
451 451  
522 +(((
452 452  0x(01): Interrupt Uplink Packet.
524 +)))
453 453  
454 454  
455 455  
456 456  === 2.4.9  ​+5V Output ===
457 457  
530 +(((
458 458  NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
532 +)))
459 459  
460 460  
535 +(((
461 461  The 5V output time can be controlled by AT Command.
537 +)))
462 462  
539 +(((
463 463  (% style="color:blue" %)**AT+5VT=1000**
541 +)))
464 464  
543 +(((
465 465  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
545 +)))
466 466  
467 467  
468 468  
... ... @@ -512,7 +512,9 @@
512 512  
513 513  * (% style="color:blue" %)**INTMOD**
514 514  
595 +(((
515 515  Downlink Payload: 06000003, Set AT+INTMOD=3
597 +)))
516 516  
517 517  
518 518  
... ... @@ -535,7 +535,9 @@
535 535  
536 536  __**Measurement the soil surface**__
537 537  
620 +(((
538 538  Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
622 +)))
539 539  
540 540  [[image:1657259653666-883.png]] ​
541 541  
... ... @@ -567,7 +567,7 @@
567 567  [[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
568 568  
569 569  
570 -Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H"]]
654 +Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
571 571  
572 572  
573 573  
... ... @@ -576,16 +576,22 @@
576 576  === 2.9.1  ​Battery Type ===
577 577  
578 578  
663 +(((
579 579  The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
665 +)))
580 580  
581 581  
668 +(((
582 582  The battery is designed to last for several years depends on the actually use environment and update interval. 
670 +)))
583 583  
584 584  
673 +(((
585 585  The battery related documents as below:
675 +)))
586 586  
587 587  * [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
588 -* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]][[ datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
678 +* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
589 589  * [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
590 590  
591 591  (((
... ... @@ -759,26 +759,37 @@
759 759  
760 760  
761 761  
852 +== 5.2  Can I calibrate NSE01 to different soil types? ==
853 +
854 +(((
855 +NSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
856 +)))
857 +
858 +
762 762  = 6.  Trouble Shooting =
763 763  
764 764  == 6.1  ​Connection problem when uploading firmware ==
765 765  
766 766  
864 +(((
865 +**Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
866 +)))
867 +
767 767  (% class="wikigeneratedid" %)
768 768  (((
769 -(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
870 +
770 770  )))
771 771  
772 772  
773 -
774 774  == 6.2  AT Command input doesn't work ==
775 775  
776 776  (((
777 777  In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
878 +
879 +
778 778  )))
779 779  
780 780  
781 -
782 782  = 7. ​ Order Info =
783 783  
784 784  
... ... @@ -790,7 +790,7 @@
790 790  
791 791  )))
792 792  
793 -= 7. Packing Info =
894 += 8.  Packing Info =
794 794  
795 795  (((
796 796  
... ... @@ -797,7 +797,6 @@
797 797  
798 798  (% style="color:#037691" %)**Package Includes**:
799 799  
800 -
801 801  * NSE01 NB-IoT Soil Moisture & EC Sensor x 1
802 802  * External antenna x 1
803 803  )))
... ... @@ -807,7 +807,6 @@
807 807  
808 808  (% style="color:#037691" %)**Dimension and weight**:
809 809  
810 -
811 811  * Size: 195 x 125 x 55 mm
812 812  * Weight:   420g
813 813  )))

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0