Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 57.1 >
edited by Xiaoling
on 2022/07/08 11:19
To version < 45.5 >
edited by Xiaoling
on 2022/07/08 10:39
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -59,6 +59,8 @@
59 59  * Micro SIM card slot for NB-IoT SIM
60 60  * 8500mAh Battery for long term use
61 61  
62 +
63 +
62 62  == 1.3  Specification ==
63 63  
64 64  
... ... @@ -67,6 +67,7 @@
67 67  * Supply Voltage: 2.1v ~~ 3.6v
68 68  * Operating Temperature: -40 ~~ 85°C
69 69  
72 +
70 70  (% style="color:#037691" %)**NB-IoT Spec:**
71 71  
72 72  * - B1 @H-FDD: 2100MHz
... ... @@ -76,6 +76,7 @@
76 76  * - B20 @H-FDD: 800MHz
77 77  * - B28 @H-FDD: 700MHz
78 78  
82 +
79 79  (% style="color:#037691" %)**Probe Specification:**
80 80  
81 81  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
... ... @@ -122,7 +122,6 @@
122 122  
123 123  == 2.2 ​ Configure the NSE01 ==
124 124  
125 -
126 126  === 2.2.1 Test Requirement ===
127 127  
128 128  
... ... @@ -132,12 +132,11 @@
132 132  * The local NB-IoT network used the band that NSE01 supports.
133 133  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
134 134  
135 -(((
138 +
136 136  Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
137 -)))
138 138  
139 139  
140 -[[image:1657249419225-449.png]]
142 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.gif]]
141 141  
142 142  
143 143  
... ... @@ -145,151 +145,158 @@
145 145  
146 146  Insert the NB-IoT Card get from your provider.
147 147  
150 +
148 148  User need to take out the NB-IoT module and insert the SIM card like below:
149 149  
150 150  
151 -[[image:1657249468462-536.png]]
154 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image004.gif]]
152 152  
153 153  
154 -
155 155  === 2.2.3 Connect USB – TTL to NSE01 to configure it ===
156 156  
157 -(((
158 -(((
159 -User need to configure NSE01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
160 -)))
161 -)))
162 162  
160 +User need to configure NSE01 via serial port to set the **(% style="color:blue" %)Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
163 163  
164 -**Connection:**
165 165  
166 - (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
167 167  
168 - (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
169 169  
170 - (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
165 +Connection:
171 171  
167 +USB TTL GND <~-~-~-~-> GND
172 172  
169 +USB TTL TXD <~-~-~-~-> UART_RXD
170 +
171 +USB TTL RXD <~-~-~-~-> UART_TXD
172 +
173 +
174 +
173 173  In the PC, use below serial tool settings:
174 174  
175 -* Baud: (% style="color:green" %)**9600**
176 -* Data bits:** (% style="color:green" %)8(%%)**
177 -* Stop bits: (% style="color:green" %)**1**
178 -* Parity: (% style="color:green" %)**None**
179 -* Flow Control: (% style="color:green" %)**None**
177 +* Baud: **9600**
178 +* Data bits:** 8**
179 +* Stop bits: **1**
180 +* Parity: **None**
181 +* Flow Control: **None**
180 180  
181 -(((
182 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
183 -)))
184 184  
185 -[[image:image-20220708110657-3.png]]
184 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
186 186  
187 -(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
186 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.jpg]]
188 188  
188 +Note: the valid AT Commands can be found at:
189 189  
190 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
190 190  
191 -=== 2.2.4 Use CoAP protocol to uplink data ===
192 192  
193 -(% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
193 +1.
194 +11.
195 +111. Use CoAP protocol to uplink data 
194 194  
195 195  
196 -**Use below commands:**
198 +Note: if you don’t have CoAP server, you can refer this link to set up one:
197 197  
198 -* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
199 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
200 -* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
200 +[[http:~~/~~/wiki.dragino.com/index.php?title=Set_up_CoAP_Server>>url:http://wiki.dragino.com/index.php?title=Set_up_CoAP_Server]]
201 201  
202 202  
203 +Use below commands:
203 203  
204 -For parameter description, please refer to AT command set
205 +* **AT+PRO=1**    ~/~/ Set to use CoAP protocol to uplink
206 +* **AT+SERVADDR=120.24.4.116,5683   **~/~/ to set CoAP server address and port
207 +* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0"       **~/~/Set COAP resource path
205 205  
206 -[[image:1657249793983-486.png]]
207 207  
210 +For parameter description, please refer to AT command set
208 208  
209 -After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
212 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.jpg]]
210 210  
211 -[[image:1657249831934-534.png]]
212 212  
215 +After configure the server address and **reset the device** (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
213 213  
217 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.jpg]]
214 214  
215 -=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
219 +1.
220 +11.
221 +111. Use UDP protocol to uplink data(Default protocol)
216 216  
223 +
217 217  This feature is supported since firmware version v1.0.1
218 218  
219 219  
220 -* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
221 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
222 -* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
227 +* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
228 +* **AT+SERVADDR=120.24.4.116,5601   **~/~/ to set UDP server address and port
229 +* **AT+CFM=1       **~/~/If the server does not respond, this command is unnecessary
223 223  
231 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.jpg]]
224 224  
225 225  
226 -[[image:1657249864775-321.png]]
227 227  
228 228  
229 229  
230 -[[image:1657249930215-289.png]]
237 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.jpg]]
231 231  
232 232  
240 +1.
241 +11.
242 +111. Use MQTT protocol to uplink data
233 233  
234 -=== 2.2.6 Use MQTT protocol to uplink data ===
235 235  
236 236  This feature is supported since firmware version v110
237 237  
238 238  
239 -* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
240 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
241 -* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
242 -* (% style="color:blue" %)**AT+UNAME=UNAME  **(%%)~/~/Set the username of MQTT
243 -* (% style="color:blue" %)**AT+PWD=PWD  **(%%)~/~/Set the password of MQTT
244 -* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB  **(%%)~/~/Set the sending topic of MQTT
245 -* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          **(%%) ~/~/Set the subscription topic of MQTT
248 +* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
249 +* **AT+SERVADDR=120.24.4.116,1883   **~/~/Set MQTT server address and port
250 +* **AT+CLIENT=CLIENT **~/~/Set up the CLIENT of MQTT
251 +* **AT+UNAME=UNAME                           **~/~/Set the username of MQTT
252 +* **AT+PWD=PWD                                      **~/~/Set the password of MQTT
253 +* **AT+PUBTOPIC=NSE01_PUB   **~/~/Set the sending topic of MQTT
254 +* **AT+SUBTOPIC=NSE01_SUB    **~/~/Set the subscription topic of MQTT
246 246  
247 247  
257 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.gif]]
248 248  
249 -[[image:1657249978444-674.png]]
259 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.jpg]]
250 250  
251 251  
252 -[[image:1657249990869-686.png]]
262 +MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
253 253  
254 254  
265 +1.
266 +11.
267 +111. Use TCP protocol to uplink data
255 255  
256 -(((
257 -MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
258 -)))
259 259  
270 +This feature is supported since firmware version v110
260 260  
261 261  
262 -=== 2.2.7 Use TCP protocol to uplink data ===
273 +* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
274 +* **AT+SERVADDR=120.24.4.116,5600   **~/~/ to set TCP server address and port
263 263  
264 -This feature is supported since firmware version v110
276 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.jpg]]
265 265  
266 266  
267 -* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
268 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
269 269  
270 -[[image:1657250217799-140.png]]
280 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]
271 271  
272 272  
273 -[[image:1657250255956-604.png]]
283 +1.
284 +11.
285 +111. Change Update Interval
274 274  
287 +User can use below command to change the **uplink interval**.
275 275  
276 -=== 2.2.8 Change Update Interval ===
289 +**~ AT+TDC=600      **~/~/ Set Update Interval to 600s
277 277  
278 -User can use below command to change the (% style="color:green" %)**uplink interval**.
279 279  
280 -* (% style="color:blue" %)**AT+TDC=600      ** (%%)~/~/ Set Update Interval to 600s
292 +**NOTE:**
281 281  
294 +1. By default, the device will send an uplink message every 1 hour.
282 282  
283 -(((
284 -(% style="color:red" %)**NOTE:**
285 -)))
286 286  
287 -(((
288 -(% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
289 -)))
290 290  
291 291  
292 292  
300 +
301 +
293 293  == 2.3 Uplink Payload ==
294 294  
295 295  
1657249419225-449.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -81.0 KB
Content
1657249468462-536.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -483.6 KB
Content
1657249793983-486.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -85.8 KB
Content
1657249831934-534.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -72.5 KB
Content
1657249864775-321.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.0 KB
Content
1657249930215-289.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -77.3 KB
Content
1657249978444-674.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -139.5 KB
Content
1657249990869-686.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -96.9 KB
Content
1657250217799-140.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -98.7 KB
Content
1657250255956-604.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -99.0 KB
Content
image-20220708110657-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -251.7 KB
Content
image-20220708111918-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -38.8 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0