Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 45.5 >
edited by Xiaoling
on 2022/07/08 10:39
To version < 49.1 >
edited by Xiaoling
on 2022/07/08 11:09
>
Change comment: Uploaded new attachment "1657249793983-486.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -59,8 +59,6 @@
59 59  * Micro SIM card slot for NB-IoT SIM
60 60  * 8500mAh Battery for long term use
61 61  
62 -
63 -
64 64  == 1.3  Specification ==
65 65  
66 66  
... ... @@ -69,7 +69,6 @@
69 69  * Supply Voltage: 2.1v ~~ 3.6v
70 70  * Operating Temperature: -40 ~~ 85°C
71 71  
72 -
73 73  (% style="color:#037691" %)**NB-IoT Spec:**
74 74  
75 75  * - B1 @H-FDD: 2100MHz
... ... @@ -79,7 +79,6 @@
79 79  * - B20 @H-FDD: 800MHz
80 80  * - B28 @H-FDD: 700MHz
81 81  
82 -
83 83  (% style="color:#037691" %)**Probe Specification:**
84 84  
85 85  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
... ... @@ -126,6 +126,7 @@
126 126  
127 127  == 2.2 ​ Configure the NSE01 ==
128 128  
125 +
129 129  === 2.2.1 Test Requirement ===
130 130  
131 131  
... ... @@ -135,11 +135,12 @@
135 135  * The local NB-IoT network used the band that NSE01 supports.
136 136  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
137 137  
138 -
135 +(((
139 139  Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
137 +)))
140 140  
141 141  
142 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.gif]]
140 +[[image:1657249419225-449.png]]
143 143  
144 144  
145 145  
... ... @@ -147,86 +147,79 @@
147 147  
148 148  Insert the NB-IoT Card get from your provider.
149 149  
150 -
151 151  User need to take out the NB-IoT module and insert the SIM card like below:
152 152  
153 153  
154 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image004.gif]]
151 +[[image:1657249468462-536.png]]
155 155  
156 156  
154 +
157 157  === 2.2.3 Connect USB – TTL to NSE01 to configure it ===
158 158  
157 +(((
158 +(((
159 +User need to configure NSE01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
160 +)))
161 +)))
159 159  
160 -User need to configure NSE01 via serial port to set the **(% style="color:blue" %)Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
161 161  
164 +**Connection:**
162 162  
166 + (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
163 163  
168 + (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
164 164  
165 -Connection:
170 + (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
166 166  
167 -USB TTL GND <~-~-~-~-> GND
168 168  
169 -USB TTL TXD <~-~-~-~-> UART_RXD
170 -
171 -USB TTL RXD <~-~-~-~-> UART_TXD
172 -
173 -
174 -
175 175  In the PC, use below serial tool settings:
176 176  
177 -* Baud: **9600**
178 -* Data bits:** 8**
179 -* Stop bits: **1**
180 -* Parity: **None**
181 -* Flow Control: **None**
175 +* Baud: (% style="color:green" %)**9600**
176 +* Data bits:** (% style="color:green" %)8(%%)**
177 +* Stop bits: (% style="color:green" %)**1**
178 +* Parity: (% style="color:green" %)**None**
179 +* Flow Control: (% style="color:green" %)**None**
182 182  
181 +(((
182 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
183 +)))
183 183  
184 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
185 +[[image:image-20220708110657-3.png]]
185 185  
186 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.jpg]]
187 +(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
187 187  
188 -Note: the valid AT Commands can be found at:
189 189  
190 -[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
191 191  
191 +=== 2.2.4 Use CoAP protocol to uplink data ===
192 192  
193 -1.
194 -11.
195 -111. Use CoAP protocol to uplink data 
193 +(% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/index.php?title=Set_up_CoAP_Server>>url:http://wiki.dragino.com/index.php?title=Set_up_CoAP_Server]]
196 196  
197 197  
198 -Note: if you don’t have CoAP server, you can refer this link to set up one:
199 -
200 -[[http:~~/~~/wiki.dragino.com/index.php?title=Set_up_CoAP_Server>>url:http://wiki.dragino.com/index.php?title=Set_up_CoAP_Server]]
201 -
202 -
203 203  Use below commands:
204 204  
205 -* **AT+PRO=1**    ~/~/ Set to use CoAP protocol to uplink
206 -* **AT+SERVADDR=120.24.4.116,5683   **~/~/ to set CoAP server address and port
207 -* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0"       **~/~/Set COAP resource path
198 +* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
199 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
200 +* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
208 208  
209 -
210 210  For parameter description, please refer to AT command set
211 211  
212 212  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.jpg]]
213 213  
214 214  
215 -After configure the server address and **reset the device** (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
207 +After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
216 216  
217 217  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.jpg]]
218 218  
219 -1.
220 -11.
221 -111. Use UDP protocol to uplink data(Default protocol)
222 222  
212 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
223 223  
214 +
224 224  This feature is supported since firmware version v1.0.1
225 225  
226 226  
227 -* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
228 -* **AT+SERVADDR=120.24.4.116,5601   **~/~/ to set UDP server address and port
229 -* **AT+CFM=1       **~/~/If the server does not respond, this command is unnecessary
218 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
219 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
220 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
230 230  
231 231  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.jpg]]
232 232  
... ... @@ -237,23 +237,20 @@
237 237  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.jpg]]
238 238  
239 239  
240 -1.
241 -11.
242 -111. Use MQTT protocol to uplink data
231 +=== 2.2.6 Use MQTT protocol to uplink data ===
243 243  
244 244  
245 245  This feature is supported since firmware version v110
246 246  
247 247  
248 -* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
249 -* **AT+SERVADDR=120.24.4.116,1883   **~/~/Set MQTT server address and port
250 -* **AT+CLIENT=CLIENT **~/~/Set up the CLIENT of MQTT
251 -* **AT+UNAME=UNAME                           **~/~/Set the username of MQTT
252 -* **AT+PWD=PWD                                      **~/~/Set the password of MQTT
253 -* **AT+PUBTOPIC=NSE01_PUB   **~/~/Set the sending topic of MQTT
254 -* **AT+SUBTOPIC=NSE01_SUB    **~/~/Set the subscription topic of MQTT
237 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
238 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
239 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
240 +* (% style="color:blue" %)**AT+UNAME=UNAME            **(%%)~/~/Set the username of MQTT
241 +* (% style="color:blue" %)**AT+PWD=PWD                  **(%%)~/~/Set the password of MQTT
242 +* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB     **(%%)~/~/Set the sending topic of MQTT
243 +* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          **(%%) ~/~/Set the subscription topic of MQTT
255 255  
256 -
257 257  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.gif]]
258 258  
259 259  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.jpg]]
... ... @@ -262,16 +262,14 @@
262 262  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
263 263  
264 264  
265 -1.
266 -11.
267 -111. Use TCP protocol to uplink data
253 +=== 2.2.7 Use TCP protocol to uplink data ===
268 268  
269 269  
270 270  This feature is supported since firmware version v110
271 271  
272 272  
273 -* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
274 -* **AT+SERVADDR=120.24.4.116,5600   **~/~/ to set TCP server address and port
259 +* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
260 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
275 275  
276 276  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.jpg]]
277 277  
... ... @@ -280,18 +280,16 @@
280 280  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]
281 281  
282 282  
283 -1.
284 -11.
285 -111. Change Update Interval
269 +=== 2.2.8 Change Update Interval ===
286 286  
287 -User can use below command to change the **uplink interval**.
271 +User can use below command to change the (% style="color:green" %)**uplink interval**.
288 288  
289 -**~ AT+TDC=600      **~/~/ Set Update Interval to 600s
273 +**~ (% style="color:blue" %)AT+TDC=600      (%%)**(% style="color:blue" %) (%%)~/~/ Set Update Interval to 600s
290 290  
291 291  
292 -**NOTE:**
276 +(% style="color:red" %)**NOTE:**
293 293  
294 -1. By default, the device will send an uplink message every 1 hour.
278 +(% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
295 295  
296 296  
297 297  
1657249419225-449.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657249468462-536.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +483.6 KB
Content
1657249793983-486.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +85.8 KB
Content
image-20220708110657-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +251.7 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0