Skip to Content
Last modified by Mengting Qiu on 2024/04/02 16:44
From version 32.5
edited by Xiaoling
on 2022/06/07 11:33
Change comment: There is no comment for this version
To version 65.12
edited by Xiaoling
on 2022/07/08 15:49
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual
1 +NSE01 - NB-IoT Soil Moisture & EC Sensor User Manual
Content
... ... @@ -3,8 +3,16 @@
3 3  
4 4  
5 5  
6 -**Contents:**
7 7  
7 +
8 +
9 +
10 +
11 +
12 +
13 +
14 +**Table of Contents:**
15 +
8 8  {{toc/}}
9 9  
10 10  
... ... @@ -12,1013 +12,806 @@
12 12  
13 13  
14 14  
15 -= 1. Introduction =
16 16  
17 -== 1.1 ​What is LoRaWAN Soil Moisture & EC Sensor ==
24 += 1.  Introduction =
18 18  
26 +== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
27 +
19 19  (((
20 -The Dragino LSE01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil Moisture & EC Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
21 -)))
29 +
22 22  
23 23  (((
24 -It detects (% style="color:#4f81bd" %)**Soil Moisture**(%%), (% style="color:#4f81bd" %)**Soil Temperature**(%%) and (% style="color:#4f81bd" %)**Soil Conductivity**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
32 +Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
25 25  )))
26 26  
27 27  (((
28 -The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
36 +It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
29 29  )))
30 30  
31 31  (((
32 -LES01 is powered by (% style="color:#4f81bd" %)**4000mA or 8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 10 years.
40 +The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
33 33  )))
34 34  
35 35  (((
36 -Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
44 +NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
37 37  )))
38 38  
47 +
48 +)))
39 39  
40 40  [[image:1654503236291-817.png]]
41 41  
42 42  
43 -[[image:1654503265560-120.png]]
53 +[[image:1657245163077-232.png]]
44 44  
45 45  
46 46  
47 -== 1.2 ​Features ==
57 +== 1.2 ​ Features ==
48 48  
49 -* LoRaWAN 1.0.3 Class A
50 -* Ultra low power consumption
59 +* NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
51 51  * Monitor Soil Moisture
52 52  * Monitor Soil Temperature
53 53  * Monitor Soil Conductivity
54 -* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
55 55  * AT Commands to change parameters
56 56  * Uplink on periodically
57 57  * Downlink to change configure
58 58  * IP66 Waterproof Enclosure
59 -* 4000mAh or 8500mAh Battery for long term use
67 +* Ultra-Low Power consumption
68 +* AT Commands to change parameters
69 +* Micro SIM card slot for NB-IoT SIM
70 +* 8500mAh Battery for long term use
60 60  
61 -== 1.3 Specification ==
62 62  
63 -Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
73 +== 1.3  Specification ==
64 64  
65 -[[image:image-20220606162220-5.png]]
66 66  
76 +(% style="color:#037691" %)**Common DC Characteristics:**
67 67  
78 +* Supply Voltage: 2.1v ~~ 3.6v
79 +* Operating Temperature: -40 ~~ 85°C
68 68  
69 -== ​1.4 Applications ==
81 +(% style="color:#037691" %)**NB-IoT Spec:**
70 70  
71 -* Smart Agriculture
83 +* - B1 @H-FDD: 2100MHz
84 +* - B3 @H-FDD: 1800MHz
85 +* - B8 @H-FDD: 900MHz
86 +* - B5 @H-FDD: 850MHz
87 +* - B20 @H-FDD: 800MHz
88 +* - B28 @H-FDD: 700MHz
72 72  
73 -(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
74 -​
90 +Probe(% style="color:#037691" %)** Specification:**
75 75  
76 -== 1.5 Firmware Change log ==
92 +Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
77 77  
94 +[[image:image-20220708101224-1.png]]
78 78  
79 -**LSE01 v1.0 :**  Release
80 80  
81 81  
98 +== ​1.4  Applications ==
82 82  
83 -= 2. Configure LSE01 to connect to LoRaWAN network =
100 +* Smart Agriculture
84 84  
85 -== 2.1 How it works ==
102 +(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
103 +​
86 86  
87 -(((
88 -The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
89 -)))
105 +== 1.5  Pin Definitions ==
90 90  
91 -(((
92 -In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.200BUsingtheATCommands"]].
93 -)))
94 94  
108 +[[image:1657246476176-652.png]]
95 95  
96 96  
97 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
98 98  
99 -Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
112 += 2.  Use NSE01 to communicate with IoT Server =
100 100  
114 +== 2.1  How it works ==
101 101  
102 -[[image:1654503992078-669.png]]
103 103  
117 +(((
118 +The NSE01 is equipped with a NB-IoT module, the pre-loaded firmware in NSE01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSE01.
119 +)))
104 104  
105 -The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
106 106  
122 +(((
123 +The diagram below shows the working flow in default firmware of NSE01:
124 +)))
107 107  
108 -**Step 1**: Create a device in TTN with the OTAA keys from LSE01.
126 +[[image:image-20220708101605-2.png]]
109 109  
110 -Each LSE01 is shipped with a sticker with the default device EUI as below:
128 +(((
129 +
130 +)))
111 111  
112 -[[image:image-20220606163732-6.jpeg]]
113 113  
114 -You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
115 115  
116 -**Add APP EUI in the application**
134 +== 2.2 ​ Configure the NSE01 ==
117 117  
118 118  
119 -[[image:1654504596150-405.png]]
137 +=== 2.2.1 Test Requirement ===
120 120  
121 121  
140 +(((
141 +To use NSE01 in your city, make sure meet below requirements:
142 +)))
122 122  
123 -**Add APP KEY and DEV EUI**
144 +* Your local operator has already distributed a NB-IoT Network there.
145 +* The local NB-IoT network used the band that NSE01 supports.
146 +* Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
124 124  
125 -[[image:1654504683289-357.png]]
148 +(((
149 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
150 +)))
126 126  
127 127  
153 +[[image:1657249419225-449.png]]
128 128  
129 -**Step 2**: Power on LSE01
130 130  
131 131  
132 -Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
157 +=== 2.2.2 Insert SIM card ===
133 133  
134 -[[image:image-20220606163915-7.png]]
159 +(((
160 +Insert the NB-IoT Card get from your provider.
161 +)))
135 135  
136 -
137 -**Step 3:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
138 -
139 -[[image:1654504778294-788.png]]
140 -
141 -
142 -
143 -== 2.3 Uplink Payload ==
144 -
145 -=== 2.3.1 MOD~=0(Default Mode) ===
146 -
147 -LSE01 will uplink payload via LoRaWAN with below payload format: 
148 -
149 -
150 -Uplink payload includes in total 11 bytes.
151 -
152 -
153 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
154 -|(((
155 -**Size**
156 -
157 -**(bytes)**
158 -)))|**2**|**2**|**2**|**2**|**2**|**1**
159 -|**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
160 -Temperature
161 -
162 -(Reserve, Ignore now)
163 -)))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]]|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]]|(((
164 -MOD & Digital Interrupt
165 -
166 -(Optional)
163 +(((
164 +User need to take out the NB-IoT module and insert the SIM card like below:
167 167  )))
168 168  
169 169  
168 +[[image:1657249468462-536.png]]
170 170  
171 -=== 2.3.2 MOD~=1(Original value) ===
172 172  
173 -This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
174 174  
175 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
176 -|(((
177 -**Size**
172 +=== 2.2.3 Connect USB – TTL to NSE01 to configure it ===
178 178  
179 -**(bytes)**
180 -)))|**2**|**2**|**2**|**2**|**2**|**1**
181 -|**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
182 -Temperature
183 -
184 -(Reserve, Ignore now)
185 -)))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]](raw)|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]](raw)|(((
186 -MOD & Digital Interrupt
187 -
188 -(Optional)
174 +(((
175 +(((
176 +User need to configure NSE01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
189 189  )))
178 +)))
190 190  
191 191  
181 +**Connection:**
192 192  
193 -=== 2.3.3 Battery Info ===
183 + (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
194 194  
195 -Check the battery voltage for LSE01.
185 + (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
196 196  
197 -Ex1: 0x0B45 = 2885mV
187 + (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
198 198  
199 -Ex2: 0x0B49 = 2889mV
200 200  
190 +In the PC, use below serial tool settings:
201 201  
192 +* Baud:  (% style="color:green" %)**9600**
193 +* Data bits:** (% style="color:green" %)8(%%)**
194 +* Stop bits: (% style="color:green" %)**1**
195 +* Parity:  (% style="color:green" %)**None**
196 +* Flow Control: (% style="color:green" %)**None**
202 202  
203 -=== 2.3.4 Soil Moisture ===
204 -
205 -Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
206 -
207 -For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
208 -
209 -
210 -(% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
211 -
212 -
213 -
214 -=== 2.3.5 Soil Temperature ===
215 -
216 - Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
217 -
218 -**Example**:
219 -
220 -If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
221 -
222 -If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
223 -
224 -
225 -
226 -=== 2.3.6 Soil Conductivity (EC) ===
227 -
228 228  (((
229 -Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
199 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
230 230  )))
231 231  
232 -(((
233 -For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
234 -)))
202 +[[image:image-20220708110657-3.png]]
235 235  
236 236  (((
237 -Generally, the EC value of irrigation water is less than 800uS / cm.
205 +(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
238 238  )))
239 239  
240 -(((
241 -
242 -)))
243 243  
244 -(((
245 -
246 -)))
247 247  
248 -=== 2.3.7 MOD ===
210 +=== 2.2.4 Use CoAP protocol to uplink data ===
249 249  
250 -Firmware version at least v2.1 supports changing mode.
212 +(% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
251 251  
252 -For example, bytes[10]=90
253 253  
254 -mod=(bytes[10]>>7)&0x01=1.
215 +**Use below commands:**
255 255  
217 +* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
218 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
219 +* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
256 256  
257 -**Downlink Command:**
221 +For parameter description, please refer to AT command set
258 258  
259 -If payload = 0x0A00, workmode=0
223 +[[image:1657249793983-486.png]]
260 260  
261 -If** **payload =** **0x0A01, workmode=1
262 262  
226 +After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
263 263  
228 +[[image:1657249831934-534.png]]
264 264  
265 -=== 2.3.8 ​Decode payload in The Things Network ===
266 266  
267 -While using TTN network, you can add the payload format to decode the payload.
268 268  
232 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
269 269  
270 -[[image:1654505570700-128.png]]
234 +This feature is supported since firmware version v1.0.1
271 271  
272 -The payload decoder function for TTN is here:
273 273  
274 -LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
237 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
238 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
239 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
275 275  
241 +[[image:1657249864775-321.png]]
276 276  
277 277  
278 -== 2.4 Uplink Interval ==
244 +[[image:1657249930215-289.png]]
279 279  
280 -The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
281 281  
282 282  
248 +=== 2.2.6 Use MQTT protocol to uplink data ===
283 283  
284 -== 2.5 Downlink Payload ==
250 +This feature is supported since firmware version v110
285 285  
286 -By default, LSE50 prints the downlink payload to console port.
287 287  
288 -[[image:image-20220606165544-8.png]]
253 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
254 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
255 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
256 +* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/Set the username of MQTT
257 +* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/Set the password of MQTT
258 +* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/Set the sending topic of MQTT
259 +* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          **(%%) ~/~/Set the subscription topic of MQTT
289 289  
261 +[[image:1657249978444-674.png]]
290 290  
291 -**Examples:**
292 292  
264 +[[image:1657249990869-686.png]]
293 293  
294 -* **Set TDC**
295 295  
296 -If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
267 +(((
268 +MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
269 +)))
297 297  
298 -Payload:    01 00 00 1E    TDC=30S
299 299  
300 -Payload:    01 00 00 3C    TDC=60S
301 301  
273 +=== 2.2.7 Use TCP protocol to uplink data ===
302 302  
303 -* **Reset**
275 +This feature is supported since firmware version v110
304 304  
305 -If payload = 0x04FF, it will reset the LSE01
306 306  
278 +* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
279 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
307 307  
308 -* **CFM**
281 +[[image:1657250217799-140.png]]
309 309  
310 -Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
311 311  
284 +[[image:1657250255956-604.png]]
312 312  
313 313  
314 -== 2.6 ​Show Data in DataCake IoT Server ==
315 315  
316 -[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
288 +=== 2.2.8 Change Update Interval ===
317 317  
290 +User can use below command to change the (% style="color:green" %)**uplink interval**.
318 318  
319 -**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
292 +* (% style="color:blue" %)**AT+TDC=600      ** (%%)~/~/ Set Update Interval to 600s
320 320  
321 -**Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
294 +(((
295 +(% style="color:red" %)**NOTE:**
296 +)))
322 322  
298 +(((
299 +(% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
300 +)))
323 323  
324 -[[image:1654505857935-743.png]]
325 325  
326 326  
327 -[[image:1654505874829-548.png]]
304 +== 2.3  Uplink Payload ==
328 328  
329 -Step 3: Create an account or log in Datacake.
306 +In this mode, uplink payload includes in total 18 bytes
330 330  
331 -Step 4: Search the LSE01 and add DevEUI.
308 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
309 +|=(% style="width: 60px;" %)(((
310 +**Size(bytes)**
311 +)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
312 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
332 332  
314 +If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
333 333  
334 -[[image:1654505905236-553.png]]
335 335  
317 +[[image:image-20220708111918-4.png]]
336 336  
337 -After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
338 338  
339 -[[image:1654505925508-181.png]]
320 +The payload is ASCII string, representative same HEX:
340 340  
322 +0x72403155615900640c7817075e0a8c02f900 where:
341 341  
324 +* Device ID: 0x 724031556159 = 724031556159
325 +* Version: 0x0064=100=1.0.0
342 342  
343 -== 2.7 Frequency Plans ==
327 +* BAT: 0x0c78 = 3192 mV = 3.192V
328 +* Singal: 0x17 = 23
329 +* Soil Moisture: 0x075e= 1886 = 18.86  %
330 +* Soil Temperature:0x0a8c =2700=27 °C
331 +* Soil Conductivity(EC) = 0x02f9 =761 uS /cm
332 +* Interrupt: 0x00 = 0
344 344  
345 -The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
346 346  
335 +== 2.4  Payload Explanation and Sensor Interface ==
347 347  
348 -=== 2.7.1 EU863-870 (EU868) ===
349 349  
350 -(% style="color:#037691" %)** Uplink:**
338 +=== 2.4.1  Device ID ===
351 351  
352 -868.1 - SF7BW125 to SF12BW125
340 +By default, the Device ID equal to the last 6 bytes of IMEI.
353 353  
354 -868.3 - SF7BW125 to SF12BW125 and SF7BW250
342 +User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
355 355  
356 -868.5 - SF7BW125 to SF12BW125
344 +**Example:**
357 357  
358 -867.1 - SF7BW125 to SF12BW125
346 +AT+DEUI=A84041F15612
359 359  
360 -867.3 - SF7BW125 to SF12BW125
348 +The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
361 361  
362 -867.5 - SF7BW125 to SF12BW125
363 363  
364 -867.7 - SF7BW125 to SF12BW125
365 365  
366 -867.9 - SF7BW125 to SF12BW125
352 +=== 2.4.2  Version Info ===
367 367  
368 -868.8 - FSK
354 +Specify the software version: 0x64=100, means firmware version 1.00.
369 369  
356 +For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
370 370  
371 -(% style="color:#037691" %)** Downlink:**
372 372  
373 -Uplink channels 1-9 (RX1)
374 374  
375 -869.525 - SF9BW125 (RX2 downlink only)
360 +=== 2.4.3  Battery Info ===
376 376  
362 +(((
363 +Check the battery voltage for LSE01.
364 +)))
377 377  
366 +(((
367 +Ex1: 0x0B45 = 2885mV
368 +)))
378 378  
379 -=== 2.7.2 US902-928(US915) ===
370 +(((
371 +Ex2: 0x0B49 = 2889mV
372 +)))
380 380  
381 -Used in USA, Canada and South America. Default use CHE=2
382 382  
383 -(% style="color:#037691" %)**Uplink:**
384 384  
385 -903.9 - SF7BW125 to SF10BW125
376 +=== 2.4.4  Signal Strength ===
386 386  
387 -904.1 - SF7BW125 to SF10BW125
378 +NB-IoT Network signal Strength.
388 388  
389 -904.3 - SF7BW125 to SF10BW125
380 +**Ex1: 0x1d = 29**
390 390  
391 -904.5 - SF7BW125 to SF10BW125
382 +(% style="color:blue" %)**0**(%%)  -113dBm or less
392 392  
393 -904.7 - SF7BW125 to SF10BW125
384 +(% style="color:blue" %)**1**(%%)  -111dBm
394 394  
395 -904.9 - SF7BW125 to SF10BW125
386 +(% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
396 396  
397 -905.1 - SF7BW125 to SF10BW125
388 +(% style="color:blue" %)**31**  (%%) -51dBm or greater
398 398  
399 -905.3 - SF7BW125 to SF10BW125
390 +(% style="color:blue" %)**99**   (%%) Not known or not detectable
400 400  
401 401  
402 -(% style="color:#037691" %)**Downlink:**
403 403  
404 -923.3 - SF7BW500 to SF12BW500
394 +=== 2.4.5  Soil Moisture ===
405 405  
406 -923.9 - SF7BW500 to SF12BW500
396 +(((
397 +Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
398 +)))
407 407  
408 -924.5 - SF7BW500 to SF12BW500
400 +(((
401 +For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
402 +)))
409 409  
410 -925.1 - SF7BW500 to SF12BW500
404 +(((
405 +
406 +)))
411 411  
412 -925.7 - SF7BW500 to SF12BW500
408 +(((
409 +(% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
410 +)))
413 413  
414 -926.3 - SF7BW500 to SF12BW500
415 415  
416 -926.9 - SF7BW500 to SF12BW500
417 417  
418 -927.5 - SF7BW500 to SF12BW500
414 +=== 2.4.6  Soil Temperature ===
419 419  
420 -923.3 - SF12BW500(RX2 downlink only)
416 +(((
417 + Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
418 +)))
421 421  
420 +(((
421 +**Example**:
422 +)))
422 422  
424 +(((
425 +If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
426 +)))
423 423  
424 -=== 2.7.3 CN470-510 (CN470) ===
428 +(((
429 +If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
430 +)))
425 425  
426 -Used in China, Default use CHE=1
427 427  
428 -(% style="color:#037691" %)**Uplink:**
429 429  
430 -486.3 - SF7BW125 to SF12BW125
434 +=== 2.4.7  Soil Conductivity (EC) ===
431 431  
432 -486.5 - SF7BW125 to SF12BW125
436 +(((
437 +Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
438 +)))
433 433  
434 -486.7 - SF7BW125 to SF12BW125
440 +(((
441 +For example, if the data you get from the register is __**0x00 0xC8**__, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
442 +)))
435 435  
436 -486.9 - SF7BW125 to SF12BW125
444 +(((
445 +Generally, the EC value of irrigation water is less than 800uS / cm.
446 +)))
437 437  
438 -487.1 - SF7BW125 to SF12BW125
448 +(((
449 +
450 +)))
439 439  
440 -487.3 - SF7BW125 to SF12BW125
452 +(((
453 +
454 +)))
441 441  
442 -487.5 - SF7BW125 to SF12BW125
456 +=== 2.4.8  Digital Interrupt ===
443 443  
444 -487.7 - SF7BW125 to SF12BW125
458 +Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
445 445  
460 +The command is:
446 446  
447 -(% style="color:#037691" %)**Downlink:**
462 +(% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
448 448  
449 -506.7 - SF7BW125 to SF12BW125
450 450  
451 -506.9 - SF7BW125 to SF12BW125
465 +The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
452 452  
453 -507.1 - SF7BW125 to SF12BW125
454 454  
455 -507.3 - SF7BW125 to SF12BW125
468 +Example:
456 456  
457 -507.5 - SF7BW125 to SF12BW125
470 +0x(00): Normal uplink packet.
458 458  
459 -507.7 - SF7BW125 to SF12BW125
472 +0x(01): Interrupt Uplink Packet.
460 460  
461 -507.9 - SF7BW125 to SF12BW125
462 462  
463 -508.1 - SF7BW125 to SF12BW125
464 464  
465 -505.3 - SF12BW125 (RX2 downlink only)
476 +=== 2.4.9  ​+5V Output ===
466 466  
478 +NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
467 467  
468 468  
469 -=== 2.7.4 AU915-928(AU915) ===
481 +The 5V output time can be controlled by AT Command.
470 470  
471 -Default use CHE=2
483 +(% style="color:blue" %)**AT+5VT=1000**
472 472  
473 -(% style="color:#037691" %)**Uplink:**
485 +Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
474 474  
475 -916.8 - SF7BW125 to SF12BW125
476 476  
477 -917.0 - SF7BW125 to SF12BW125
478 478  
479 -917.2 - SF7BW125 to SF12BW125
489 +== 2.5  Downlink Payload ==
480 480  
481 -917.4 - SF7BW125 to SF12BW125
491 +By default, NSE01 prints the downlink payload to console port.
482 482  
483 -917.6 - SF7BW125 to SF12BW125
493 +[[image:image-20220708133731-5.png]]
484 484  
485 -917.8 - SF7BW125 to SF12BW125
486 486  
487 -918.0 - SF7BW125 to SF12BW125
496 +(((
497 +(% style="color:blue" %)**Examples:**
498 +)))
488 488  
489 -918.2 - SF7BW125 to SF12BW125
500 +(((
501 +
502 +)))
490 490  
504 +* (((
505 +(% style="color:blue" %)**Set TDC**
506 +)))
491 491  
492 -(% style="color:#037691" %)**Downlink:**
508 +(((
509 +If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
510 +)))
493 493  
494 -923.3 - SF7BW500 to SF12BW500
512 +(((
513 +Payload:    01 00 00 1E    TDC=30S
514 +)))
495 495  
496 -923.9 - SF7BW500 to SF12BW500
516 +(((
517 +Payload:    01 00 00 3C    TDC=60S
518 +)))
497 497  
498 -924.5 - SF7BW500 to SF12BW500
520 +(((
521 +
522 +)))
499 499  
500 -925.1 - SF7BW500 to SF12BW500
524 +* (((
525 +(% style="color:blue" %)**Reset**
526 +)))
501 501  
502 -925.7 - SF7BW500 to SF12BW500
528 +(((
529 +If payload = 0x04FF, it will reset the NSE01
530 +)))
503 503  
504 -926.3 - SF7BW500 to SF12BW500
505 505  
506 -926.9 - SF7BW500 to SF12BW500
533 +* (% style="color:blue" %)**INTMOD**
507 507  
508 -927.5 - SF7BW500 to SF12BW500
535 +Downlink Payload: 06000003, Set AT+INTMOD=3
509 509  
510 -923.3 - SF12BW500(RX2 downlink only)
511 511  
512 512  
539 +== 2.6  ​LED Indicator ==
513 513  
514 -=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
541 +(((
542 +The NSE01 has an internal LED which is to show the status of different state.
515 515  
516 -(% style="color:#037691" %)**Default Uplink channel:**
517 517  
518 -923.2 - SF7BW125 to SF10BW125
545 +* When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
546 +* Then the LED will be on for 1 second means device is boot normally.
547 +* After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
548 +* For each uplink probe, LED will be on for 500ms.
549 +)))
519 519  
520 -923.4 - SF7BW125 to SF10BW125
521 521  
522 522  
523 -(% style="color:#037691" %)**Additional Uplink Channel**:
524 524  
525 -(OTAA mode, channel added by JoinAccept message)
554 +== 2.7  Installation in Soil ==
526 526  
527 -(% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
556 +__**Measurement the soil surface**__
528 528  
529 -922.2 - SF7BW125 to SF10BW125
558 +Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
530 530  
531 -922.4 - SF7BW125 to SF10BW125
560 +[[image:1657259653666-883.png]] ​
532 532  
533 -922.6 - SF7BW125 to SF10BW125
534 534  
535 -922.8 - SF7BW125 to SF10BW125
563 +(((
564 +
536 536  
537 -923.0 - SF7BW125 to SF10BW125
566 +(((
567 +Dig a hole with diameter > 20CM.
568 +)))
538 538  
539 -922.0 - SF7BW125 to SF10BW125
570 +(((
571 +Horizontal insert the probe to the soil and fill the hole for long term measurement.
572 +)))
573 +)))
540 540  
575 +[[image:1654506665940-119.png]]
541 541  
542 -(% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
577 +(((
578 +
579 +)))
543 543  
544 -923.6 - SF7BW125 to SF10BW125
545 545  
546 -923.8 - SF7BW125 to SF10BW125
582 +== 2.8  ​Firmware Change Log ==
547 547  
548 -924.0 - SF7BW125 to SF10BW125
549 549  
550 -924.2 - SF7BW125 to SF10BW125
585 +Download URL & Firmware Change log
551 551  
552 -924.4 - SF7BW125 to SF10BW125
587 +[[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
553 553  
554 -924.6 - SF7BW125 to SF10BW125
555 555  
590 +Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
556 556  
557 -(% style="color:#037691" %)** Downlink:**
558 558  
559 -Uplink channels 1-8 (RX1)
560 560  
561 -923.2 - SF10BW125 (RX2)
594 +== 2.9  ​Battery Analysis ==
562 562  
596 +=== 2.9.1  ​Battery Type ===
563 563  
564 564  
565 -=== 2.7.6 KR920-923 (KR920) ===
599 +The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
566 566  
567 -Default channel:
568 568  
569 -922.1 - SF7BW125 to SF12BW125
602 +The battery is designed to last for several years depends on the actually use environment and update interval. 
570 570  
571 -922.3 - SF7BW125 to SF12BW125
572 572  
573 -922.5 - SF7BW125 to SF12BW125
605 +The battery related documents as below:
574 574  
607 +* [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
608 +* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
609 +* [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
575 575  
576 -(% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
577 -
578 -922.1 - SF7BW125 to SF12BW125
579 -
580 -922.3 - SF7BW125 to SF12BW125
581 -
582 -922.5 - SF7BW125 to SF12BW125
583 -
584 -922.7 - SF7BW125 to SF12BW125
585 -
586 -922.9 - SF7BW125 to SF12BW125
587 -
588 -923.1 - SF7BW125 to SF12BW125
589 -
590 -923.3 - SF7BW125 to SF12BW125
591 -
592 -
593 -(% style="color:#037691" %)**Downlink:**
594 -
595 -Uplink channels 1-7(RX1)
596 -
597 -921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
598 -
599 -
600 -
601 -=== 2.7.7 IN865-867 (IN865) ===
602 -
603 -(% style="color:#037691" %)** Uplink:**
604 -
605 -865.0625 - SF7BW125 to SF12BW125
606 -
607 -865.4025 - SF7BW125 to SF12BW125
608 -
609 -865.9850 - SF7BW125 to SF12BW125
610 -
611 -
612 -(% style="color:#037691" %) **Downlink:**
613 -
614 -Uplink channels 1-3 (RX1)
615 -
616 -866.550 - SF10BW125 (RX2)
617 -
618 -
619 -
620 -
621 -== 2.8 LED Indicator ==
622 -
623 -The LSE01 has an internal LED which is to show the status of different state.
624 -
625 -* Blink once when device power on.
626 -* Solid ON for 5 seconds once device successful Join the network.
627 -* Blink once when device transmit a packet.
628 -
629 -== 2.9 Installation in Soil ==
630 -
631 -**Measurement the soil surface**
632 -
633 -
634 -[[image:1654506634463-199.png]] ​
635 -
636 636  (((
637 -(((
638 -Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
612 +[[image:image-20220708140453-6.png]]
639 639  )))
640 -)))
641 641  
642 642  
643 -[[image:1654506665940-119.png]]
644 644  
645 -(((
646 -Dig a hole with diameter > 20CM.
647 -)))
617 +=== 2.9.2  Power consumption Analyze ===
648 648  
649 649  (((
650 -Horizontal insert the probe to the soil and fill the hole for long term measurement.
620 +Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
651 651  )))
652 652  
653 653  
654 -== 2.10 ​Firmware Change Log ==
655 -
656 656  (((
657 -**Firmware download link:**
625 +Instruction to use as below:
658 658  )))
659 659  
660 660  (((
661 -[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
629 +(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
662 662  )))
663 663  
664 -(((
665 -
666 -)))
667 667  
668 668  (((
669 -**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
634 +(% style="color:blue" %)**Step 2: **(%%) Open it and choose
670 670  )))
671 671  
672 -(((
673 -
637 +* (((
638 +Product Model
674 674  )))
675 -
676 -(((
677 -**V1.0.**
640 +* (((
641 +Uplink Interval
678 678  )))
643 +* (((
644 +Working Mode
645 +)))
679 679  
680 680  (((
681 -Release
648 +And the Life expectation in difference case will be shown on the right.
682 682  )))
683 683  
651 +[[image:image-20220708141352-7.jpeg]]
684 684  
685 -== 2.11 ​Battery Analysis ==
686 686  
687 -=== 2.11.1 ​Battery Type ===
688 688  
689 -(((
690 -The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
691 -)))
655 +=== 2.9.3  ​Battery Note ===
692 692  
693 693  (((
694 -The battery is designed to last for more than 5 years for the LSN50.
658 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
695 695  )))
696 696  
697 -(((
698 -(((
699 -The battery-related documents are as below:
700 -)))
701 -)))
702 702  
703 -* (((
704 -[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
705 -)))
706 -* (((
707 -[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
708 -)))
709 -* (((
710 -[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
711 -)))
712 712  
713 - [[image:image-20220606171726-9.png]]
663 +=== 2.9.4  Replace the battery ===
714 714  
715 -
716 -
717 -=== 2.11.2 ​Battery Note ===
718 -
719 719  (((
720 -The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
666 +The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
721 721  )))
722 722  
723 723  
724 724  
725 -=== 2.11.3 Replace the battery ===
671 += 3. ​ Access NB-IoT Module =
726 726  
727 727  (((
728 -If Battery is lower than 2.7v, user should replace the battery of LSE01.
674 +Users can directly access the AT command set of the NB-IoT module.
729 729  )))
730 730  
731 731  (((
732 -You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
678 +The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
733 733  )))
734 734  
735 -(((
736 -The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
737 -)))
681 +[[image:1657261278785-153.png]]
738 738  
739 739  
740 740  
741 -= 3. ​Using the AT Commands =
685 += 4.  Using the AT Commands =
742 742  
743 -== 3.1 Access AT Commands ==
687 +== 4.1  Access AT Commands ==
744 744  
689 +See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
745 745  
746 -LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
747 747  
748 -[[image:1654501986557-872.png||height="391" width="800"]]
692 +AT+<CMD>?  : Help on <CMD>
749 749  
694 +AT+<CMD>         : Run <CMD>
750 750  
751 -Or if you have below board, use below connection:
696 +AT+<CMD>=<value> : Set the value
752 752  
698 +AT+<CMD>=?  : Get the value
753 753  
754 -[[image:1654502005655-729.png||height="503" width="801"]]
755 755  
756 -
757 -
758 -In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
759 -
760 -
761 - [[image:1654502050864-459.png||height="564" width="806"]]
762 -
763 -
764 -Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
765 -
766 -
767 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
768 -
769 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
770 -
771 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
772 -
773 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
774 -
775 -
776 776  (% style="color:#037691" %)**General Commands**(%%)      
777 777  
778 -(% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention       
703 +AT  : Attention       
779 779  
780 -(% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help     
705 +AT?  : Short Help     
781 781  
782 -(% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset    
707 +ATZ  : MCU Reset    
783 783  
784 -(% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval 
709 +AT+TDC  : Application Data Transmission Interval
785 785  
711 +AT+CFG  : Print all configurations
786 786  
787 -(% style="color:#037691" %)**Keys, IDs and EUIs management**
713 +AT+CFGMOD           : Working mode selection
788 788  
789 -(% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI      
715 +AT+INTMOD            : Set the trigger interrupt mode
790 790  
791 -(% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key     
717 +AT+5VT  : Set extend the time of 5V power  
792 792  
793 -(% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
719 +AT+PRO  : Choose agreement
794 794  
795 -(% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address     
721 +AT+WEIGRE  : Get weight or set weight to 0
796 796  
797 -(% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI     
723 +AT+WEIGAP  : Get or Set the GapValue of weight
798 798  
799 -(% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection) 
725 +AT+RXDL  : Extend the sending and receiving time
800 800  
801 -(% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network  
727 +AT+CNTFAC  : Get or set counting parameters
802 802  
803 -(% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode       
729 +AT+SERVADDR  : Server Address
804 804  
805 -(% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status       
806 806  
807 -(% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network       
732 +(% style="color:#037691" %)**COAP Management**      
808 808  
809 -(% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode    
734 +AT+URI            : Resource parameters
810 810  
811 -(% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status    
812 812  
813 -(% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
737 +(% style="color:#037691" %)**UDP Management**
814 814  
815 -(% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format      
739 +AT+CFM          : Upload confirmation mode (only valid for UDP)
816 816  
817 -(% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data      
818 818  
819 -(% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
742 +(% style="color:#037691" %)**MQTT Management**
820 820  
744 +AT+CLIENT               : Get or Set MQTT client
821 821  
822 -(% style="color:#037691" %)**LoRa Network Management**
746 +AT+UNAME  : Get or Set MQTT Username
823 823  
824 -(% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
748 +AT+PWD                  : Get or Set MQTT password
825 825  
826 -(% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
750 +AT+PUBTOPIC  : Get or Set MQTT publish topic
827 827  
828 -(% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting 
752 +AT+SUBTOPIC  : Get or Set MQTT subscription topic
829 829  
830 -(% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)     
831 831  
832 -(% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink       
755 +(% style="color:#037691" %)**Information**          
833 833  
834 -(% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink   
757 +AT+FDR  : Factory Data Reset
835 835  
836 -(% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
759 +AT+PWORD  : Serial Access Password
837 837  
838 -(% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
839 839  
840 -(% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode   
841 841  
842 -(% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1      
763 += ​5.  FAQ =
843 843  
844 -(% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2      
765 +== 5.1 ​ How to Upgrade Firmware ==
845 845  
846 -(% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate 
847 847  
848 -(% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
849 -
850 -(% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
851 -
852 -(% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
853 -
854 -
855 -(% style="color:#037691" %)**Information** 
856 -
857 -(% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet   
858 -
859 -(% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet   
860 -
861 -(% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band       
862 -
863 -(% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
864 -
865 -(% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port    
866 -
867 -(% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
868 -
869 - (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
870 -
871 -
872 -= ​4. FAQ =
873 -
874 -== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
875 -
876 876  (((
877 -You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
878 -When downloading the images, choose the required image file for download. ​
769 +User can upgrade the firmware for 1) bug fix, 2) new feature release.
879 879  )))
880 880  
881 881  (((
882 -
773 +Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
883 883  )))
884 884  
885 885  (((
886 -How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
777 +(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
887 887  )))
888 888  
889 -(((
890 -
891 -)))
892 892  
893 -(((
894 -You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
895 -)))
896 896  
897 -(((
898 -
899 -)))
782 += 6.  Trouble Shooting =
900 900  
901 -(((
902 -For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
903 -)))
784 +== 6.1  ​Connection problem when uploading firmware ==
904 904  
905 -[[image:image-20220606154726-3.png]]
906 906  
907 -
908 -When you use the TTN network, the US915 frequency bands use are:
909 -
910 -* 903.9 - SF7BW125 to SF10BW125
911 -* 904.1 - SF7BW125 to SF10BW125
912 -* 904.3 - SF7BW125 to SF10BW125
913 -* 904.5 - SF7BW125 to SF10BW125
914 -* 904.7 - SF7BW125 to SF10BW125
915 -* 904.9 - SF7BW125 to SF10BW125
916 -* 905.1 - SF7BW125 to SF10BW125
917 -* 905.3 - SF7BW125 to SF10BW125
918 -* 904.6 - SF8BW500
919 -
787 +(% class="wikigeneratedid" %)
920 920  (((
921 -Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
789 +(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
922 922  )))
923 923  
924 -(% class="box infomessage" %)
925 -(((
926 -**AT+CHE=2**
927 -)))
928 928  
929 -(% class="box infomessage" %)
930 -(((
931 -**ATZ**
932 -)))
933 933  
934 -(((
935 -to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
936 -)))
794 +== 6.2  AT Command input doesn't work ==
937 937  
938 938  (((
939 -
797 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
940 940  )))
941 941  
942 -(((
943 -The **AU915** band is similar. Below are the AU915 Uplink Channels.
944 -)))
945 945  
946 -[[image:image-20220606154825-4.png]]
947 947  
802 += 7. ​ Order Info =
948 948  
949 949  
950 -= 5. Trouble Shooting =
805 +Part Number**:** (% style="color:#4f81bd" %)**NSE01**
951 951  
952 -== 5.1 ​Why I can’t join TTN in US915 / AU915 bands? ==
953 953  
954 -It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
955 -
956 -
957 -== 5.2 AT Command input doesn’t work ==
958 -
959 -(((
960 -In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
961 -)))
962 -
963 -
964 -== 5.3 Device rejoin in at the second uplink packet ==
965 -
966 -(% style="color:#4f81bd" %)**Issue describe as below:**
967 -
968 -[[image:1654500909990-784.png]]
969 -
970 -
971 -(% style="color:#4f81bd" %)**Cause for this issue:**
972 -
973 -(((
974 -The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
975 -)))
976 -
977 -
978 -(% style="color:#4f81bd" %)**Solution: **
979 -
980 -All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
981 -
982 -[[image:1654500929571-736.png||height="458" width="832"]]
983 -
984 -
985 -= 6. ​Order Info =
986 -
987 -
988 -Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
989 -
990 -
991 -(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
992 -
993 -* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
994 -* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
995 -* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
996 -* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
997 -* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
998 -* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
999 -* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1000 -* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1001 -
1002 -(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
1003 -
1004 -* (% style="color:red" %)**4**(%%): 4000mAh battery
1005 -* (% style="color:red" %)**8**(%%): 8500mAh battery
1006 -
1007 1007  (% class="wikigeneratedid" %)
1008 1008  (((
1009 1009  
1010 1010  )))
1011 1011  
1012 -= 7. Packing Info =
813 += 8.  Packing Info =
1013 1013  
1014 1014  (((
1015 1015  
1016 1016  
1017 1017  (% style="color:#037691" %)**Package Includes**:
1018 -)))
1019 1019  
1020 -* (((
1021 -LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
820 +
821 +* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
822 +* External antenna x 1
1022 1022  )))
1023 1023  
1024 1024  (((
... ... @@ -1025,30 +1025,20 @@
1025 1025  
1026 1026  
1027 1027  (% style="color:#037691" %)**Dimension and weight**:
1028 -)))
1029 1029  
1030 -* (((
1031 -Device Size: cm
830 +
831 +* Size: 195 x 125 x 55 mm
832 +* Weight:   420g
1032 1032  )))
1033 -* (((
1034 -Device Weight: g
1035 -)))
1036 -* (((
1037 -Package Size / pcs : cm
1038 -)))
1039 -* (((
1040 -Weight / pcs : g
1041 1041  
835 +(((
836 +
1042 1042  
838 +
1043 1043  
1044 1044  )))
1045 1045  
1046 -= 8. Support =
842 += 9.  Support =
1047 1047  
1048 1048  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1049 1049  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1050 -
1051 -
1052 -~)~)~)
1053 -~)~)~)
1054 -~)~)~)
1657245163077-232.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657246476176-652.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +492.6 KB
Content
1657249419225-449.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657249468462-536.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +483.6 KB
Content
1657249793983-486.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +85.8 KB
Content
1657249831934-534.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +72.5 KB
Content
1657249864775-321.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +87.0 KB
Content
1657249930215-289.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +77.3 KB
Content
1657249978444-674.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +139.5 KB
Content
1657249990869-686.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +96.9 KB
Content
1657250217799-140.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +98.7 KB
Content
1657250255956-604.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +99.0 KB
Content
1657259653666-883.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +344.4 KB
Content
1657260785982-288.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +138.2 KB
Content
1657261119050-993.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +126.1 KB
Content
1657261278785-153.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +126.1 KB
Content
image-20220610172436-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +370.3 KB
Content
image-20220708101224-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +22.2 KB
Content
image-20220708101605-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +87.5 KB
Content
image-20220708110657-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +251.7 KB
Content
image-20220708111918-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +38.8 KB
Content
image-20220708133731-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +8.7 KB
Content
image-20220708140453-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +132.7 KB
Content
image-20220708141352-7.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +102.7 KB
Content