Skip to Content
Last modified by Mengting Qiu on 2024/04/02 16:44
From version 31.16
edited by Xiaoling
on 2022/06/07 09:25
Change comment: There is no comment for this version
To version 65.2
edited by Xiaoling
on 2022/07/08 15:03
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual
1 +NSE01 - NB-IoT Soil Moisture & EC Sensor User Manual
Content
... ... @@ -8,1014 +8,827 @@
8 8  
9 9  
10 10  
11 -= 1. Introduction =
12 12  
13 -== 1.1 ​What is LoRaWAN Soil Moisture & EC Sensor ==
14 14  
15 -(((
16 -The Dragino LSE01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil Moisture & EC Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
17 -)))
18 18  
19 -(((
20 -It detects (% style="color:#4f81bd" %)**Soil Moisture**(%%), (% style="color:#4f81bd" %)**Soil Temperature**(%%) and (% style="color:#4f81bd" %)**Soil Conductivity**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
21 -)))
14 +**Table of Contents:**
22 22  
23 -(((
24 -The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
25 -)))
26 26  
27 -(((
28 -LES01 is powered by (% style="color:#4f81bd" %)**4000mA or 8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 10 years.
29 -)))
30 30  
18 +
19 +
20 +
21 += 1.  Introduction =
22 +
23 +== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
24 +
31 31  (((
32 -Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
33 -)))
26 +
34 34  
28 +Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
35 35  
30 +It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
31 +
32 +The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
33 +
34 +NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
35 +
36 +
37 +)))
38 +
36 36  [[image:1654503236291-817.png]]
37 37  
38 38  
39 -[[image:1654503265560-120.png]]
42 +[[image:1657245163077-232.png]]
40 40  
41 41  
42 42  
43 43  == 1.2 ​Features ==
44 44  
45 -* LoRaWAN 1.0.3 Class A
46 -* Ultra low power consumption
48 +* NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
47 47  * Monitor Soil Moisture
48 48  * Monitor Soil Temperature
49 49  * Monitor Soil Conductivity
50 -* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
51 51  * AT Commands to change parameters
52 52  * Uplink on periodically
53 53  * Downlink to change configure
54 54  * IP66 Waterproof Enclosure
55 -* 4000mAh or 8500mAh Battery for long term use
56 +* Ultra-Low Power consumption
57 +* AT Commands to change parameters
58 +* Micro SIM card slot for NB-IoT SIM
59 +* 8500mAh Battery for long term use
56 56  
57 57  
58 58  
59 -== 1.3 Specification ==
60 60  
61 -Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
64 +== 1.3  Specification ==
62 62  
63 -[[image:image-20220606162220-5.png]]
64 64  
67 +(% style="color:#037691" %)**Common DC Characteristics:**
65 65  
69 +* Supply Voltage: 2.1v ~~ 3.6v
70 +* Operating Temperature: -40 ~~ 85°C
66 66  
67 -== ​1.4 Applications ==
68 68  
69 -* Smart Agriculture
70 70  
71 -(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
72 -​
74 +(% style="color:#037691" %)**NB-IoT Spec:**
73 73  
74 -== 1.5 Firmware Change log ==
76 +* - B1 @H-FDD: 2100MHz
77 +* - B3 @H-FDD: 1800MHz
78 +* - B8 @H-FDD: 900MHz
79 +* - B5 @H-FDD: 850MHz
80 +* - B20 @H-FDD: 800MHz
81 +* - B28 @H-FDD: 700MHz
75 75  
76 76  
77 -**LSE01 v1.0 :**  Release
78 78  
85 +Probe(% style="color:#037691" %)** Specification:**
79 79  
87 +Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
80 80  
81 -= 2. Configure LSE01 to connect to LoRaWAN network =
89 +[[image:image-20220708101224-1.png]]
82 82  
83 -== 2.1 How it works ==
84 84  
85 -(((
86 -The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
87 -)))
88 88  
89 -(((
90 -In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.​UsingtheATCommands"]].
91 -)))
93 +== ​1.4  Applications ==
92 92  
95 +* Smart Agriculture
93 93  
97 +(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
98 +​
94 94  
95 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
100 +== 1.5  Pin Definitions ==
96 96  
97 -Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
98 98  
103 +[[image:1657246476176-652.png]]
99 99  
100 -[[image:1654503992078-669.png]]
101 101  
102 102  
103 -The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
107 += 2.  Use NSE01 to communicate with IoT Server =
104 104  
109 +== 2.1  How it works ==
105 105  
106 -**Step 1**: Create a device in TTN with the OTAA keys from LSE01.
107 107  
108 -Each LSE01 is shipped with a sticker with the default device EUI as below:
112 +(((
113 +The NSE01 is equipped with a NB-IoT module, the pre-loaded firmware in NSE01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSE01.
114 +)))
109 109  
110 -[[image:image-20220606163732-6.jpeg]]
111 111  
112 -You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
117 +(((
118 +The diagram below shows the working flow in default firmware of NSE01:
119 +)))
113 113  
114 -**Add APP EUI in the application**
121 +[[image:image-20220708101605-2.png]]
115 115  
116 -
117 -[[image:1654504596150-405.png]]
118 -
119 -
120 -
121 -**Add APP KEY and DEV EUI**
122 -
123 -[[image:1654504683289-357.png]]
124 -
125 -
126 -
127 -**Step 2**: Power on LSE01
128 -
129 -
130 -Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
131 -
132 -[[image:image-20220606163915-7.png]]
133 -
134 -
135 -**Step 3:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
136 -
137 -[[image:1654504778294-788.png]]
138 -
139 -
140 -
141 -== 2.3 Uplink Payload ==
142 -
143 -=== 2.3.1 MOD~=0(Default Mode) ===
144 -
145 -LSE01 will uplink payload via LoRaWAN with below payload format: 
146 -
147 -
148 -Uplink payload includes in total 11 bytes.
123 +(((
149 149  
150 -
151 -|(((
152 -**Size**
153 -
154 -**(bytes)**
155 -)))|**2**|**2**|**2**|**2**|**2**|**1**
156 -|**Value**|[[BAT>>path:#bat]]|(((
157 -Temperature
158 -
159 -(Reserve, Ignore now)
160 -)))|[[Soil Moisture>>path:#soil_moisture]]|[[Soil Temperature>>path:#soil_tem]]|[[Soil Conductivity (EC)>>path:#EC]]|(((
161 -MOD & Digital Interrupt
162 -
163 -(Optional)
164 164  )))
165 165  
166 -[[image:1654504881641-514.png]]
167 167  
168 168  
129 +== 2.2 ​ Configure the NSE01 ==
169 169  
170 -=== 2.3.2 MOD~=1(Original value) ===
171 171  
172 -This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
132 +=== 2.2.1 Test Requirement ===
173 173  
174 -|(((
175 -**Size**
176 176  
177 -**(bytes)**
178 -)))|**2**|**2**|**2**|**2**|**2**|**1**
179 -|**Value**|[[BAT>>path:#bat]]|(((
180 -Temperature
135 +To use NSE01 in your city, make sure meet below requirements:
181 181  
182 -(Reserve, Ignore now)
183 -)))|[[Soil Moisture>>path:#soil_moisture]](raw)|[[Soil Temperature>>path:#soil_tem]]|[[Soil Conductivity (EC)>>path:#EC]](raw)|(((
184 -MOD & Digital Interrupt
137 +* Your local operator has already distributed a NB-IoT Network there.
138 +* The local NB-IoT network used the band that NSE01 supports.
139 +* Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
185 185  
186 -(Optional)
141 +(((
142 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
187 187  )))
188 188  
189 -[[image:1654504907647-967.png]]
190 190  
146 +[[image:1657249419225-449.png]]
191 191  
192 192  
193 -=== 2.3.3 Battery Info ===
194 194  
195 -Check the battery voltage for LSE01.
150 +=== 2.2.2 Insert SIM card ===
196 196  
197 -Ex1: 0x0B45 = 2885mV
152 +Insert the NB-IoT Card get from your provider.
198 198  
199 -Ex2: 0x0B49 = 2889mV
154 +User need to take out the NB-IoT module and insert the SIM card like below:
200 200  
201 201  
157 +[[image:1657249468462-536.png]]
202 202  
203 -=== 2.3.4 Soil Moisture ===
204 204  
205 -Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
206 206  
207 -For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
161 +=== 2.2.3 Connect USB – TTL to NSE01 to configure it ===
208 208  
209 -
210 -(% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
211 -
212 -
213 -
214 -=== 2.3.5 Soil Temperature ===
215 -
216 - Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
217 -
218 -**Example**:
219 -
220 -If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
221 -
222 -If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
223 -
224 -
225 -
226 -=== 2.3.6 Soil Conductivity (EC) ===
227 -
228 228  (((
229 -Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
230 -)))
231 -
232 232  (((
233 -For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
165 +User need to configure NSE01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
234 234  )))
235 -
236 -(((
237 -Generally, the EC value of irrigation water is less than 800uS / cm.
238 238  )))
239 239  
240 -(((
241 -
242 -)))
243 243  
244 -(((
245 -
246 -)))
170 +**Connection:**
247 247  
248 -=== 2.3.7 MOD ===
172 + (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
249 249  
250 -Firmware version at least v2.1 supports changing mode.
174 + (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
251 251  
252 -For example, bytes[10]=90
176 + (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
253 253  
254 -mod=(bytes[10]>>7)&0x01=1.
255 255  
179 +In the PC, use below serial tool settings:
256 256  
257 -Downlink Command:
181 +* Baud:  (% style="color:green" %)**9600**
182 +* Data bits:** (% style="color:green" %)8(%%)**
183 +* Stop bits: (% style="color:green" %)**1**
184 +* Parity:  (% style="color:green" %)**None**
185 +* Flow Control: (% style="color:green" %)**None**
258 258  
259 -If payload = 0x0A00, workmode=0
187 +(((
188 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
189 +)))
260 260  
261 -If** **payload =** **0x0A01, workmode=1
191 +[[image:image-20220708110657-3.png]]
262 262  
193 +(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
263 263  
264 264  
265 -=== 2.3.8 ​Decode payload in The Things Network ===
266 266  
267 -While using TTN network, you can add the payload format to decode the payload.
197 +=== 2.2.4 Use CoAP protocol to uplink data ===
268 268  
199 +(% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
269 269  
270 -[[image:1654505570700-128.png]]
271 271  
272 -The payload decoder function for TTN is here:
202 +**Use below commands:**
273 273  
274 -LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
204 +* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
205 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
206 +* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
275 275  
208 +For parameter description, please refer to AT command set
276 276  
277 -== 2.4 Uplink Interval ==
210 +[[image:1657249793983-486.png]]
278 278  
279 -The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
280 280  
281 -[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]
213 +After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
282 282  
215 +[[image:1657249831934-534.png]]
283 283  
284 284  
285 -== 2.5 Downlink Payload ==
286 286  
287 -By default, LSE50 prints the downlink payload to console port.
219 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
288 288  
289 -[[image:image-20220606165544-8.png]]
221 +This feature is supported since firmware version v1.0.1
290 290  
291 291  
292 -**Examples:**
224 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
225 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
226 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
293 293  
228 +[[image:1657249864775-321.png]]
294 294  
295 -* **Set TDC**
296 296  
297 -If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
231 +[[image:1657249930215-289.png]]
298 298  
299 -Payload:    01 00 00 1E    TDC=30S
300 300  
301 -Payload:    01 00 00 3C    TDC=60S
302 302  
235 +=== 2.2.6 Use MQTT protocol to uplink data ===
303 303  
304 -* **Reset**
237 +This feature is supported since firmware version v110
305 305  
306 -If payload = 0x04FF, it will reset the LSE01
307 307  
240 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
241 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
242 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
243 +* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/Set the username of MQTT
244 +* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/Set the password of MQTT
245 +* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/Set the sending topic of MQTT
246 +* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          **(%%) ~/~/Set the subscription topic of MQTT
308 308  
309 -* **CFM**
248 +[[image:1657249978444-674.png]]
310 310  
311 -Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
312 312  
251 +[[image:1657249990869-686.png]]
313 313  
314 314  
315 -== 2.6 ​Show Data in DataCake IoT Server ==
254 +(((
255 +MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
256 +)))
316 316  
317 -[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
318 318  
319 319  
320 -**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
260 +=== 2.2.7 Use TCP protocol to uplink data ===
321 321  
322 -**Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
262 +This feature is supported since firmware version v110
323 323  
324 324  
325 -[[image:1654505857935-743.png]]
265 +* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
266 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
326 326  
268 +[[image:1657250217799-140.png]]
327 327  
328 -[[image:1654505874829-548.png]]
329 329  
330 -Step 3: Create an account or log in Datacake.
271 +[[image:1657250255956-604.png]]
331 331  
332 -Step 4: Search the LSE01 and add DevEUI.
333 333  
334 334  
335 -[[image:1654505905236-553.png]]
275 +=== 2.2.8 Change Update Interval ===
336 336  
277 +User can use below command to change the (% style="color:green" %)**uplink interval**.
337 337  
338 -After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
279 +* (% style="color:blue" %)**AT+TDC=600      ** (%%)~/~/ Set Update Interval to 600s
339 339  
340 -[[image:1654505925508-181.png]]
281 +(((
282 +(% style="color:red" %)**NOTE:**
283 +)))
341 341  
285 +(((
286 +(% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
287 +)))
342 342  
343 343  
344 -== 2.7 Frequency Plans ==
345 345  
346 -The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
291 +== 2.3  Uplink Payload ==
347 347  
293 +In this mode, uplink payload includes in total 18 bytes
348 348  
349 -=== 2.7.1 EU863-870 (EU868) ===
295 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
296 +|=(% style="width: 50px;" %)(((
297 +**Size(bytes)**
298 +)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
299 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
350 350  
351 -(% style="color:#037691" %)** Uplink:**
301 +If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
352 352  
353 -868.1 - SF7BW125 to SF12BW125
354 354  
355 -868.3 - SF7BW125 to SF12BW125 and SF7BW250
304 +[[image:image-20220708111918-4.png]]
356 356  
357 -868.5 - SF7BW125 to SF12BW125
358 358  
359 -867.1 - SF7BW125 to SF12BW125
307 +The payload is ASCII string, representative same HEX:
360 360  
361 -867.3 - SF7BW125 to SF12BW125
309 +0x72403155615900640c7817075e0a8c02f900 where:
362 362  
363 -867.5 - SF7BW125 to SF12BW125
311 +* Device ID: 0x 724031556159 = 724031556159
312 +* Version: 0x0064=100=1.0.0
364 364  
365 -867.7 - SF7BW125 to SF12BW125
314 +* BAT: 0x0c78 = 3192 mV = 3.192V
315 +* Singal: 0x17 = 23
316 +* Soil Moisture: 0x075e= 1886 = 18.86  %
317 +* Soil Temperature:0x0a8c =2700=27 °C
318 +* Soil Conductivity(EC) = 0x02f9 =761 uS /cm
319 +* Interrupt: 0x00 = 0
366 366  
367 -867.9 - SF7BW125 to SF12BW125
368 368  
369 -868.8 - FSK
370 370  
371 371  
372 -(% style="color:#037691" %)** Downlink:**
324 +== 2.4  Payload Explanation and Sensor Interface ==
373 373  
374 -Uplink channels 1-9 (RX1)
375 375  
376 -869.525 - SF9BW125 (RX2 downlink only)
327 +=== 2.4.1  Device ID ===
377 377  
329 +By default, the Device ID equal to the last 6 bytes of IMEI.
378 378  
331 +User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
379 379  
380 -=== 2.7.2 US902-928(US915) ===
333 +**Example:**
381 381  
382 -Used in USA, Canada and South America. Default use CHE=2
335 +AT+DEUI=A84041F15612
383 383  
384 -(% style="color:#037691" %)**Uplink:**
337 +The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
385 385  
386 -903.9 - SF7BW125 to SF10BW125
387 387  
388 -904.1 - SF7BW125 to SF10BW125
389 389  
390 -904.3 - SF7BW125 to SF10BW125
341 +=== 2.4.2  Version Info ===
391 391  
392 -904.5 - SF7BW125 to SF10BW125
343 +Specify the software version: 0x64=100, means firmware version 1.00.
393 393  
394 -904.7 - SF7BW125 to SF10BW125
345 +For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
395 395  
396 -904.9 - SF7BW125 to SF10BW125
397 397  
398 -905.1 - SF7BW125 to SF10BW125
399 399  
400 -905.3 - SF7BW125 to SF10BW125
349 +=== 2.4.3  Battery Info ===
401 401  
351 +(((
352 +Check the battery voltage for LSE01.
353 +)))
402 402  
403 -(% style="color:#037691" %)**Downlink:**
355 +(((
356 +Ex1: 0x0B45 = 2885mV
357 +)))
404 404  
405 -923.3 - SF7BW500 to SF12BW500
359 +(((
360 +Ex2: 0x0B49 = 2889mV
361 +)))
406 406  
407 -923.9 - SF7BW500 to SF12BW500
408 408  
409 -924.5 - SF7BW500 to SF12BW500
410 410  
411 -925.1 - SF7BW500 to SF12BW500
365 +=== 2.4.4  Signal Strength ===
412 412  
413 -925.7 - SF7BW500 to SF12BW500
367 +NB-IoT Network signal Strength.
414 414  
415 -926.3 - SF7BW500 to SF12BW500
369 +**Ex1: 0x1d = 29**
416 416  
417 -926.9 - SF7BW500 to SF12BW500
371 +(% style="color:blue" %)**0**(%%)  -113dBm or less
418 418  
419 -927.5 - SF7BW500 to SF12BW500
373 +(% style="color:blue" %)**1**(%%)  -111dBm
420 420  
421 -923.3 - SF12BW500(RX2 downlink only)
375 +(% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
422 422  
377 +(% style="color:blue" %)**31**  (%%) -51dBm or greater
423 423  
379 +(% style="color:blue" %)**99**   (%%) Not known or not detectable
424 424  
425 -=== 2.7.3 CN470-510 (CN470) ===
426 426  
427 -Used in China, Default use CHE=1
428 428  
429 -(% style="color:#037691" %)**Uplink:**
383 +=== 2.4.5  Soil Moisture ===
430 430  
431 -486.3 - SF7BW125 to SF12BW125
385 +(((
386 +Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
387 +)))
432 432  
433 -486.5 - SF7BW125 to SF12BW125
389 +(((
390 +For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
391 +)))
434 434  
435 -486.7 - SF7BW125 to SF12BW125
393 +(((
394 +
395 +)))
436 436  
437 -486.9 - SF7BW125 to SF12BW125
397 +(((
398 +(% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
399 +)))
438 438  
439 -487.1 - SF7BW125 to SF12BW125
440 440  
441 -487.3 - SF7BW125 to SF12BW125
442 442  
443 -487.5 - SF7BW125 to SF12BW125
403 +=== 2.4.6  Soil Temperature ===
444 444  
445 -487.7 - SF7BW125 to SF12BW125
405 +(((
406 + Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
407 +)))
446 446  
409 +(((
410 +**Example**:
411 +)))
447 447  
448 -(% style="color:#037691" %)**Downlink:**
413 +(((
414 +If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
415 +)))
449 449  
450 -506.7 - SF7BW125 to SF12BW125
417 +(((
418 +If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
419 +)))
451 451  
452 -506.9 - SF7BW125 to SF12BW125
453 453  
454 -507.1 - SF7BW125 to SF12BW125
455 455  
456 -507.3 - SF7BW125 to SF12BW125
423 +=== 2.4.7  Soil Conductivity (EC) ===
457 457  
458 -507.5 - SF7BW125 to SF12BW125
425 +(((
426 +Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
427 +)))
459 459  
460 -507.7 - SF7BW125 to SF12BW125
429 +(((
430 +For example, if the data you get from the register is __**0x00 0xC8**__, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
431 +)))
461 461  
462 -507.9 - SF7BW125 to SF12BW125
433 +(((
434 +Generally, the EC value of irrigation water is less than 800uS / cm.
435 +)))
463 463  
464 -508.1 - SF7BW125 to SF12BW125
437 +(((
438 +
439 +)))
465 465  
466 -505.3 - SF12BW125 (RX2 downlink only)
441 +(((
442 +
443 +)))
467 467  
445 +=== 2.4.8  Digital Interrupt ===
468 468  
447 +Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
469 469  
470 -=== 2.7.4 AU915-928(AU915) ===
449 +The command is:
471 471  
472 -Default use CHE=2
451 +(% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
473 473  
474 -(% style="color:#037691" %)**Uplink:**
475 475  
476 -916.8 - SF7BW125 to SF12BW125
454 +The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
477 477  
478 -917.0 - SF7BW125 to SF12BW125
479 479  
480 -917.2 - SF7BW125 to SF12BW125
457 +Example:
481 481  
482 -917.4 - SF7BW125 to SF12BW125
459 +0x(00): Normal uplink packet.
483 483  
484 -917.6 - SF7BW125 to SF12BW125
461 +0x(01): Interrupt Uplink Packet.
485 485  
486 -917.8 - SF7BW125 to SF12BW125
487 487  
488 -918.0 - SF7BW125 to SF12BW125
489 489  
490 -918.2 - SF7BW125 to SF12BW125
465 +=== 2.4.9  ​+5V Output ===
491 491  
467 +NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
492 492  
493 -(% style="color:#037691" %)**Downlink:**
494 494  
495 -923.3 - SF7BW500 to SF12BW500
470 +The 5V output time can be controlled by AT Command.
496 496  
497 -923.9 - SF7BW500 to SF12BW500
472 +(% style="color:blue" %)**AT+5VT=1000**
498 498  
499 -924.5 - SF7BW500 to SF12BW500
474 +Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
500 500  
501 -925.1 - SF7BW500 to SF12BW500
502 502  
503 -925.7 - SF7BW500 to SF12BW500
504 504  
505 -926.3 - SF7BW500 to SF12BW500
478 +== 2.5  Downlink Payload ==
506 506  
507 -926.9 - SF7BW500 to SF12BW500
480 +By default, NSE01 prints the downlink payload to console port.
508 508  
509 -927.5 - SF7BW500 to SF12BW500
482 +[[image:image-20220708133731-5.png]]
510 510  
511 -923.3 - SF12BW500(RX2 downlink only)
512 512  
485 +(((
486 +(% style="color:blue" %)**Examples:**
487 +)))
513 513  
489 +(((
490 +
491 +)))
514 514  
515 -=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
493 +* (((
494 +(% style="color:blue" %)**Set TDC**
495 +)))
516 516  
517 -(% style="color:#037691" %)**Default Uplink channel:**
497 +(((
498 +If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
499 +)))
518 518  
519 -923.2 - SF7BW125 to SF10BW125
501 +(((
502 +Payload:    01 00 00 1E    TDC=30S
503 +)))
520 520  
521 -923.4 - SF7BW125 to SF10BW125
505 +(((
506 +Payload:    01 00 00 3C    TDC=60S
507 +)))
522 522  
509 +(((
510 +
511 +)))
523 523  
524 -(% style="color:#037691" %)**Additional Uplink Channel**:
513 +* (((
514 +(% style="color:blue" %)**Reset**
515 +)))
525 525  
526 -(OTAA mode, channel added by JoinAccept message)
517 +(((
518 +If payload = 0x04FF, it will reset the NSE01
519 +)))
527 527  
528 -(% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
529 529  
530 -922.2 - SF7BW125 to SF10BW125
522 +* (% style="color:blue" %)**INTMOD**
531 531  
532 -922.4 - SF7BW125 to SF10BW125
524 +Downlink Payload: 06000003, Set AT+INTMOD=3
533 533  
534 -922.6 - SF7BW125 to SF10BW125
535 535  
536 -922.8 - SF7BW125 to SF10BW125
537 537  
538 -923.0 - SF7BW125 to SF10BW125
528 +== 2.6  ​LED Indicator ==
539 539  
540 -922.0 - SF7BW125 to SF10BW125
530 +(((
531 +The NSE01 has an internal LED which is to show the status of different state.
541 541  
542 542  
543 -(% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
534 +* When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
535 +* Then the LED will be on for 1 second means device is boot normally.
536 +* After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
537 +* For each uplink probe, LED will be on for 500ms.
538 +)))
544 544  
545 -923.6 - SF7BW125 to SF10BW125
546 546  
547 -923.8 - SF7BW125 to SF10BW125
548 548  
549 -924.0 - SF7BW125 to SF10BW125
550 550  
551 -924.2 - SF7BW125 to SF10BW125
543 +== 2.7  Installation in Soil ==
552 552  
553 -924.4 - SF7BW125 to SF10BW125
545 +__**Measurement the soil surface**__
554 554  
555 -924.6 - SF7BW125 to SF10BW125
547 +Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
556 556  
549 +[[image:1657259653666-883.png]] ​
557 557  
558 -(% style="color:#037691" %)** Downlink:**
559 559  
560 -Uplink channels 1-8 (RX1)
552 +(((
553 +
561 561  
562 -923.2 - SF10BW125 (RX2)
555 +(((
556 +Dig a hole with diameter > 20CM.
557 +)))
563 563  
559 +(((
560 +Horizontal insert the probe to the soil and fill the hole for long term measurement.
561 +)))
562 +)))
564 564  
564 +[[image:1654506665940-119.png]]
565 565  
566 -=== 2.7.6 KR920-923 (KR920) ===
566 +(((
567 +
568 +)))
567 567  
568 -Default channel:
569 569  
570 -922.1 - SF7BW125 to SF12BW125
571 +== 2.8  ​Firmware Change Log ==
571 571  
572 -922.3 - SF7BW125 to SF12BW125
573 573  
574 -922.5 - SF7BW125 to SF12BW125
574 +Download URL & Firmware Change log
575 575  
576 +[[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
576 576  
577 -(% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
578 578  
579 -922.1 - SF7BW125 to SF12BW125
579 +Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H"]]
580 580  
581 -922.3 - SF7BW125 to SF12BW125
582 582  
583 -922.5 - SF7BW125 to SF12BW125
584 584  
585 -922.7 - SF7BW125 to SF12BW125
583 +== 2.9  ​Battery Analysis ==
586 586  
587 -922.9 - SF7BW125 to SF12BW125
585 +=== 2.9.1  ​Battery Type ===
588 588  
589 -923.1 - SF7BW125 to SF12BW125
590 590  
591 -923.3 - SF7BW125 to SF12BW125
588 +The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
592 592  
593 593  
594 -(% style="color:#037691" %)**Downlink:**
591 +The battery is designed to last for several years depends on the actually use environment and update interval. 
595 595  
596 -Uplink channels 1-7(RX1)
597 597  
598 -921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
594 +The battery related documents as below:
599 599  
596 +* [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
597 +* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]][[ datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
598 +* [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
600 600  
601 -
602 -=== 2.7.7 IN865-867 (IN865) ===
603 -
604 -(% style="color:#037691" %)** Uplink:**
605 -
606 -865.0625 - SF7BW125 to SF12BW125
607 -
608 -865.4025 - SF7BW125 to SF12BW125
609 -
610 -865.9850 - SF7BW125 to SF12BW125
611 -
612 -
613 -(% style="color:#037691" %) **Downlink:**
614 -
615 -Uplink channels 1-3 (RX1)
616 -
617 -866.550 - SF10BW125 (RX2)
618 -
619 -
620 -
621 -
622 -== 2.8 LED Indicator ==
623 -
624 -The LSE01 has an internal LED which is to show the status of different state.
625 -
626 -* Blink once when device power on.
627 -* Solid ON for 5 seconds once device successful Join the network.
628 -* Blink once when device transmit a packet.
629 -
630 -== 2.9 Installation in Soil ==
631 -
632 -**Measurement the soil surface**
633 -
634 -
635 -[[image:1654506634463-199.png]] ​
636 -
637 637  (((
638 -(((
639 -Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
601 +[[image:image-20220708140453-6.png]]
640 640  )))
641 -)))
642 642  
643 643  
644 -[[image:1654506665940-119.png]]
645 645  
646 -(((
647 -Dig a hole with diameter > 20CM.
648 -)))
606 +=== 2.9.2  Power consumption Analyze ===
649 649  
650 650  (((
651 -Horizontal insert the probe to the soil and fill the hole for long term measurement.
609 +Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
652 652  )))
653 653  
654 654  
655 -== 2.10 ​Firmware Change Log ==
656 -
657 657  (((
658 -**Firmware download link:**
614 +Instruction to use as below:
659 659  )))
660 660  
661 661  (((
662 -[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
618 +(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
663 663  )))
664 664  
665 -(((
666 -
667 -)))
668 668  
669 669  (((
670 -**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
623 +(% style="color:blue" %)**Step 2: **(%%) Open it and choose
671 671  )))
672 672  
673 -(((
674 -
626 +* (((
627 +Product Model
675 675  )))
676 -
677 -(((
678 -**V1.0.**
629 +* (((
630 +Uplink Interval
679 679  )))
632 +* (((
633 +Working Mode
634 +)))
680 680  
681 681  (((
682 -Release
637 +And the Life expectation in difference case will be shown on the right.
683 683  )))
684 684  
640 +[[image:image-20220708141352-7.jpeg]]
685 685  
686 -== 2.11 ​Battery Analysis ==
687 687  
688 -=== 2.11.1 ​Battery Type ===
689 689  
690 -(((
691 -The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
692 -)))
644 +=== 2.9.3  ​Battery Note ===
693 693  
694 694  (((
695 -The battery is designed to last for more than 5 years for the LSN50.
647 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
696 696  )))
697 697  
698 -(((
699 -(((
700 -The battery-related documents are as below:
701 -)))
702 -)))
703 703  
704 -* (((
705 -[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
706 -)))
707 -* (((
708 -[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
709 -)))
710 -* (((
711 -[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
712 -)))
713 713  
714 - [[image:image-20220606171726-9.png]]
652 +=== 2.9.4  Replace the battery ===
715 715  
716 -
717 -
718 -=== 2.11.2 ​Battery Note ===
719 -
720 720  (((
721 -The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
655 +The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
722 722  )))
723 723  
724 724  
725 725  
726 -=== 2.11.3 Replace the battery ===
660 += 3. ​ Access NB-IoT Module =
727 727  
728 728  (((
729 -If Battery is lower than 2.7v, user should replace the battery of LSE01.
663 +Users can directly access the AT command set of the NB-IoT module.
730 730  )))
731 731  
732 732  (((
733 -You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
667 +The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
734 734  )))
735 735  
736 -(((
737 -The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
738 -)))
670 +[[image:1657261278785-153.png]]
739 739  
740 740  
741 741  
742 -= 3. ​Using the AT Commands =
674 += 4.  Using the AT Commands =
743 743  
744 -== 3.1 Access AT Commands ==
676 +== 4.1  Access AT Commands ==
745 745  
678 +See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
746 746  
747 -LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
748 748  
749 -[[image:1654501986557-872.png]]
681 +AT+<CMD>?  : Help on <CMD>
750 750  
683 +AT+<CMD>         : Run <CMD>
751 751  
752 -Or if you have below board, use below connection:
685 +AT+<CMD>=<value> : Set the value
753 753  
687 +AT+<CMD>=?  : Get the value
754 754  
755 -[[image:1654502005655-729.png]]
756 756  
757 -
758 -
759 -In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
760 -
761 -
762 - [[image:1654502050864-459.png]]
763 -
764 -
765 -Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
766 -
767 -
768 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
769 -
770 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
771 -
772 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
773 -
774 -(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
775 -
776 -
777 777  (% style="color:#037691" %)**General Commands**(%%)      
778 778  
779 -(% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention       
692 +AT  : Attention       
780 780  
781 -(% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help     
694 +AT?  : Short Help     
782 782  
783 -(% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset    
696 +ATZ  : MCU Reset    
784 784  
785 -(% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval 
698 +AT+TDC  : Application Data Transmission Interval
786 786  
700 +AT+CFG  : Print all configurations
787 787  
788 -(% style="color:#037691" %)**Keys, IDs and EUIs management**
702 +AT+CFGMOD           : Working mode selection
789 789  
790 -(% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI      
704 +AT+INTMOD            : Set the trigger interrupt mode
791 791  
792 -(% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key     
706 +AT+5VT  : Set extend the time of 5V power  
793 793  
794 -(% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
708 +AT+PRO  : Choose agreement
795 795  
796 -(% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address     
710 +AT+WEIGRE  : Get weight or set weight to 0
797 797  
798 -(% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI     
712 +AT+WEIGAP  : Get or Set the GapValue of weight
799 799  
800 -(% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection) 
714 +AT+RXDL  : Extend the sending and receiving time
801 801  
802 -(% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network  
716 +AT+CNTFAC  : Get or set counting parameters
803 803  
804 -(% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode       
718 +AT+SERVADDR  : Server Address
805 805  
806 -(% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status       
807 807  
808 -(% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network       
721 +(% style="color:#037691" %)**COAP Management**      
809 809  
810 -(% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode    
723 +AT+URI            : Resource parameters
811 811  
812 -(% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status    
813 813  
814 -(% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
726 +(% style="color:#037691" %)**UDP Management**
815 815  
816 -(% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format      
728 +AT+CFM          : Upload confirmation mode (only valid for UDP)
817 817  
818 -(% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data      
819 819  
820 -(% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
731 +(% style="color:#037691" %)**MQTT Management**
821 821  
733 +AT+CLIENT               : Get or Set MQTT client
822 822  
823 -(% style="color:#037691" %)**LoRa Network Management**
735 +AT+UNAME  : Get or Set MQTT Username
824 824  
825 -(% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
737 +AT+PWD                  : Get or Set MQTT password
826 826  
827 -(% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
739 +AT+PUBTOPIC  : Get or Set MQTT publish topic
828 828  
829 -(% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting 
741 +AT+SUBTOPIC  : Get or Set MQTT subscription topic
830 830  
831 -(% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)     
832 832  
833 -(% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink       
744 +(% style="color:#037691" %)**Information**          
834 834  
835 -(% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink   
746 +AT+FDR  : Factory Data Reset
836 836  
837 -(% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
748 +AT+PWORD  : Serial Access Password
838 838  
839 -(% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
840 840  
841 -(% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode   
842 842  
843 -(% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1      
752 += ​5.  FAQ =
844 844  
845 -(% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2      
754 +== 5.1 ​ How to Upgrade Firmware ==
846 846  
847 -(% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate 
848 848  
849 -(% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
757 +(((
758 +User can upgrade the firmware for 1) bug fix, 2) new feature release.
759 +)))
850 850  
851 -(% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
852 -
853 -(% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
854 -
855 -
856 -(% style="color:#037691" %)**Information** 
857 -
858 -(% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet   
859 -
860 -(% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet   
861 -
862 -(% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band       
863 -
864 -(% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
865 -
866 -(% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port    
867 -
868 -(% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
869 -
870 - (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
871 -
872 -
873 -= ​4. FAQ =
874 -
875 -== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
876 -
877 -You can follow the instructions for [[how to upgrade image>>||anchor="H2.10FirmwareChangeLog"]].
878 -When downloading the images, choose the required image file for download. ​
879 -
880 -
881 -How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
882 -
883 -
884 -You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
885 -
886 -
887 -For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
888 -
889 -[[image:image-20220606154726-3.png]]
890 -
891 -When you use the TTN network, the US915 frequency bands use are:
892 -
893 -* 903.9 - SF7BW125 to SF10BW125
894 -* 904.1 - SF7BW125 to SF10BW125
895 -* 904.3 - SF7BW125 to SF10BW125
896 -* 904.5 - SF7BW125 to SF10BW125
897 -* 904.7 - SF7BW125 to SF10BW125
898 -* 904.9 - SF7BW125 to SF10BW125
899 -* 905.1 - SF7BW125 to SF10BW125
900 -* 905.3 - SF7BW125 to SF10BW125
901 -* 904.6 - SF8BW500
902 -
903 -Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
904 -
905 -(% class="box infomessage" %)
906 906  (((
907 -**AT+CHE=2**
762 +Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
908 908  )))
909 909  
910 -(% class="box infomessage" %)
911 911  (((
912 -**ATZ**
766 +(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
913 913  )))
914 914  
915 -to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
916 916  
917 917  
918 -The **AU915** band is similar. Below are the AU915 Uplink Channels.
771 += 6.  Trouble Shooting =
919 919  
920 -[[image:image-20220606154825-4.png]]
773 +== 6.1  ​Connection problem when uploading firmware ==
921 921  
922 922  
776 +(% class="wikigeneratedid" %)
777 +(((
778 +(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
779 +)))
923 923  
924 -= 5. Trouble Shooting =
925 925  
926 -== 5.1 ​Why I can’t join TTN in US915 / AU915 bands? ==
927 927  
928 -It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
783 +== 6.2  AT Command input doesn't work ==
929 929  
785 +(((
786 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
787 +)))
930 930  
931 -== 5.2 AT Command input doesn’t work ==
932 932  
933 -In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
934 934  
791 += 7. ​ Order Info =
935 935  
936 -== 5.3 Device rejoin in at the second uplink packet ==
937 937  
938 -(% style="color:#4f81bd" %)**Issue describe as below:**
794 +Part Number**:** (% style="color:#4f81bd" %)**NSE01**
939 939  
940 -[[image:1654500909990-784.png]]
941 941  
942 -
943 -(% style="color:#4f81bd" %)**Cause for this issue:**
944 -
945 -The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
946 -
947 -
948 -(% style="color:#4f81bd" %)**Solution: **
949 -
950 -All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
951 -
952 -[[image:1654500929571-736.png]]
953 -
954 -
955 -= 6. ​Order Info =
956 -
957 -
958 -Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
959 -
960 -
961 -(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
962 -
963 -* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
964 -* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
965 -* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
966 -* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
967 -* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
968 -* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
969 -* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
970 -* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
971 -
972 -(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
973 -
974 -* (% style="color:red" %)**4**(%%): 4000mAh battery
975 -* (% style="color:red" %)**8**(%%): 8500mAh battery
976 -
977 977  (% class="wikigeneratedid" %)
978 978  (((
979 979  
980 980  )))
981 981  
982 -= 7. Packing Info =
802 += 8.  Packing Info =
983 983  
984 984  (((
985 -**Package Includes**:
986 -)))
805 +
987 987  
988 -* (((
989 -LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
807 +(% style="color:#037691" %)**Package Includes**:
808 +
809 +
810 +* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
811 +* External antenna x 1
990 990  )))
991 991  
992 992  (((
993 993  
994 -)))
995 995  
996 -(((
997 -**Dimension and weight**:
998 -)))
817 +(% style="color:#037691" %)**Dimension and weight**:
999 999  
1000 -* (((
1001 -Device Size: cm
819 +
820 +* Size: 195 x 125 x 55 mm
821 +* Weight:   420g
1002 1002  )))
1003 -* (((
1004 -Device Weight: g
1005 -)))
1006 -* (((
1007 -Package Size / pcs : cm
1008 -)))
1009 -* (((
1010 -Weight / pcs : g
1011 1011  
824 +(((
825 +
1012 1012  
827 +
1013 1013  
1014 1014  )))
1015 1015  
1016 -= 8. Support =
831 += 9.  Support =
1017 1017  
1018 1018  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1019 1019  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1020 -
1021 -
1657245163077-232.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657246476176-652.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +492.6 KB
Content
1657249419225-449.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657249468462-536.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +483.6 KB
Content
1657249793983-486.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +85.8 KB
Content
1657249831934-534.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +72.5 KB
Content
1657249864775-321.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +87.0 KB
Content
1657249930215-289.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +77.3 KB
Content
1657249978444-674.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +139.5 KB
Content
1657249990869-686.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +96.9 KB
Content
1657250217799-140.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +98.7 KB
Content
1657250255956-604.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +99.0 KB
Content
1657259653666-883.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +344.4 KB
Content
1657260785982-288.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +138.2 KB
Content
1657261119050-993.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +126.1 KB
Content
1657261278785-153.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +126.1 KB
Content
image-20220610172436-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +370.3 KB
Content
image-20220708101224-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +22.2 KB
Content
image-20220708101605-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +87.5 KB
Content
image-20220708110657-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +251.7 KB
Content
image-20220708111918-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +38.8 KB
Content
image-20220708133731-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +8.7 KB
Content
image-20220708140453-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +132.7 KB
Content
image-20220708141352-7.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +102.7 KB
Content