Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 29.1 >
edited by Xiaoling
on 2022/06/06 17:10
To version < 35.16 >
edited by Xiaoling
on 2022/06/14 14:13
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,18 +1,24 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20220606151504-2.jpeg||height="848" width="848"]]
2 +[[image:image-20220606151504-2.jpeg||height="554" width="554"]]
3 3  
4 4  
5 5  
6 +**Table of Contents:**
6 6  
8 +{{toc/}}
7 7  
8 8  
9 9  
10 10  
13 +
14 +
11 11  = 1. Introduction =
12 12  
13 13  == 1.1 ​What is LoRaWAN Soil Moisture & EC Sensor ==
14 14  
15 15  (((
20 +
21 +
16 16  The Dragino LSE01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil Moisture & EC Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
17 17  )))
18 18  
... ... @@ -85,7 +85,7 @@
85 85  )))
86 86  
87 87  (((
88 -In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.​UsingtheATCommands"]].
94 +In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.200BUsingtheATCommands"]].
89 89  )))
90 90  
91 91  
... ... @@ -101,7 +101,7 @@
101 101  The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
102 102  
103 103  
104 -**Step 1**: Create a device in TTN with the OTAA keys from LSE01.
110 +(% style="color:blue" %)**Step 1**(%%):  Create a device in TTN with the OTAA keys from LSE01.
105 105  
106 106  Each LSE01 is shipped with a sticker with the default device EUI as below:
107 107  
... ... @@ -122,7 +122,7 @@
122 122  
123 123  
124 124  
125 -**Step 2**: Power on LSE01
131 +(% style="color:blue" %)**Step 2**(%%): Power on LSE01
126 126  
127 127  
128 128  Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
... ... @@ -130,7 +130,7 @@
130 130  [[image:image-20220606163915-7.png]]
131 131  
132 132  
133 -**Step 3:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
139 +(% style="color:blue" %)**Step 3**(%%)**:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
134 134  
135 135  [[image:1654504778294-788.png]]
136 136  
... ... @@ -138,86 +138,108 @@
138 138  
139 139  == 2.3 Uplink Payload ==
140 140  
147 +
141 141  === 2.3.1 MOD~=0(Default Mode) ===
142 142  
143 143  LSE01 will uplink payload via LoRaWAN with below payload format: 
144 144  
145 -
152 +(((
146 146  Uplink payload includes in total 11 bytes.
147 -
154 +)))
148 148  
156 +(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
149 149  |(((
150 150  **Size**
151 151  
152 152  **(bytes)**
153 153  )))|**2**|**2**|**2**|**2**|**2**|**1**
154 -|**Value**|[[BAT>>path:#bat]]|(((
162 +|**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
155 155  Temperature
156 156  
157 157  (Reserve, Ignore now)
158 -)))|[[Soil Moisture>>path:#soil_moisture]]|[[Soil Temperature>>path:#soil_tem]]|[[Soil Conductivity (EC)>>path:#EC]]|(((
166 +)))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]]|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]]|(((
159 159  MOD & Digital Interrupt
160 160  
161 161  (Optional)
162 162  )))
163 163  
164 -[[image:1654504881641-514.png]]
165 165  
166 166  
167 -
168 168  === 2.3.2 MOD~=1(Original value) ===
169 169  
170 170  This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
171 171  
178 +(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
172 172  |(((
173 173  **Size**
174 174  
175 175  **(bytes)**
176 176  )))|**2**|**2**|**2**|**2**|**2**|**1**
177 -|**Value**|[[BAT>>path:#bat]]|(((
184 +|**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
178 178  Temperature
179 179  
180 180  (Reserve, Ignore now)
181 -)))|[[Soil Moisture>>path:#soil_moisture]](raw)|[[Soil Temperature>>path:#soil_tem]]|[[Soil Conductivity (EC)>>path:#EC]](raw)|(((
188 +)))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]](raw)|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]](raw)|(((
182 182  MOD & Digital Interrupt
183 183  
184 184  (Optional)
185 185  )))
186 186  
187 -[[image:1654504907647-967.png]]
188 188  
189 189  
190 -
191 191  === 2.3.3 Battery Info ===
192 192  
198 +(((
193 193  Check the battery voltage for LSE01.
200 +)))
194 194  
202 +(((
195 195  Ex1: 0x0B45 = 2885mV
204 +)))
196 196  
206 +(((
197 197  Ex2: 0x0B49 = 2889mV
208 +)))
198 198  
199 199  
200 200  
201 201  === 2.3.4 Soil Moisture ===
202 202  
214 +(((
203 203  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
216 +)))
204 204  
218 +(((
205 205  For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
220 +)))
206 206  
222 +(((
223 +
224 +)))
207 207  
226 +(((
208 208  (% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
228 +)))
209 209  
210 210  
211 211  
212 212  === 2.3.5 Soil Temperature ===
213 213  
234 +(((
214 214   Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
236 +)))
215 215  
238 +(((
216 216  **Example**:
240 +)))
217 217  
242 +(((
218 218  If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
244 +)))
219 219  
246 +(((
220 220  If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
248 +)))
221 221  
222 222  
223 223  
... ... @@ -252,7 +252,7 @@
252 252  mod=(bytes[10]>>7)&0x01=1.
253 253  
254 254  
255 -Downlink Command:
283 +**Downlink Command:**
256 256  
257 257  If payload = 0x0A00, workmode=0
258 258  
... ... @@ -267,19 +267,21 @@
267 267  
268 268  [[image:1654505570700-128.png]]
269 269  
298 +(((
270 270  The payload decoder function for TTN is here:
300 +)))
271 271  
272 -LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
302 +(((
303 +LSE01 TTN Payload Decoder: [[https:~~/~~/www.dropbox.com/sh/si8icbrjlamxqdb/AAACYwjsxxr5fj_vpqRtrETAa?dl=0>>https://www.dropbox.com/sh/si8icbrjlamxqdb/AAACYwjsxxr5fj_vpqRtrETAa?dl=0]]
304 +)))
273 273  
274 274  
275 275  == 2.4 Uplink Interval ==
276 276  
277 -The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
309 +The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
278 278  
279 -[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]
280 280  
281 281  
282 -
283 283  == 2.5 Downlink Payload ==
284 284  
285 285  By default, LSE50 prints the downlink payload to console port.
... ... @@ -287,21 +287,41 @@
287 287  [[image:image-20220606165544-8.png]]
288 288  
289 289  
320 +(((
290 290  **Examples:**
322 +)))
291 291  
324 +(((
325 +
326 +)))
292 292  
293 -* **Set TDC**
328 +* (((
329 +**Set TDC**
330 +)))
294 294  
332 +(((
295 295  If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
334 +)))
296 296  
336 +(((
297 297  Payload:    01 00 00 1E    TDC=30S
338 +)))
298 298  
340 +(((
299 299  Payload:    01 00 00 3C    TDC=60S
342 +)))
300 300  
344 +(((
345 +
346 +)))
301 301  
302 -* **Reset**
348 +* (((
349 +**Reset**
350 +)))
303 303  
352 +(((
304 304  If payload = 0x04FF, it will reset the LSE01
354 +)))
305 305  
306 306  
307 307  * **CFM**
... ... @@ -312,12 +312,21 @@
312 312  
313 313  == 2.6 ​Show Data in DataCake IoT Server ==
314 314  
365 +(((
315 315  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
367 +)))
316 316  
369 +(((
370 +
371 +)))
317 317  
318 -**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
373 +(((
374 +(% style="color:blue" %)**Step 1**(%%):  Be sure that your device is programmed and properly connected to the network at this time.
375 +)))
319 319  
320 -**Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
377 +(((
378 +(% style="color:blue" %)**Step 2**(%%):  To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
379 +)))
321 321  
322 322  
323 323  [[image:1654505857935-743.png]]
... ... @@ -325,11 +325,12 @@
325 325  
326 326  [[image:1654505874829-548.png]]
327 327  
328 -Step 3: Create an account or log in Datacake.
329 329  
330 -Step 4: Search the LSE01 and add DevEUI.
388 +(% style="color:blue" %)**Step 3**(%%)**:**  Create an account or log in Datacake.
331 331  
390 +(% style="color:blue" %)**Step 4**(%%)**:**  Search the LSE01 and add DevEUI.
332 332  
392 +
333 333  [[image:1654505905236-553.png]]
334 334  
335 335  
... ... @@ -627,99 +627,120 @@
627 627  
628 628  
629 629  
690 +
691 +
630 630  == 2.9 Installation in Soil ==
631 631  
632 632  **Measurement the soil surface**
633 633  
634 634  
635 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]] ​
697 +[[image:1654506634463-199.png]] ​
636 636  
699 +(((
700 +(((
637 637  Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
702 +)))
703 +)))
638 638  
639 639  
706 +[[image:1654506665940-119.png]]
640 640  
641 -
642 -
643 -
644 -
645 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]
646 -
647 -
648 -
708 +(((
649 649  Dig a hole with diameter > 20CM.
710 +)))
650 650  
712 +(((
651 651  Horizontal insert the probe to the soil and fill the hole for long term measurement.
714 +)))
652 652  
653 653  
717 +== 2.10 ​Firmware Change Log ==
654 654  
655 -
656 -1.
657 -11. ​Firmware Change Log
658 -
719 +(((
659 659  **Firmware download link:**
721 +)))
660 660  
723 +(((
661 661  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
725 +)))
662 662  
727 +(((
728 +
729 +)))
663 663  
664 -**Firmware Upgrade Method:**
731 +(((
732 +**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
733 +)))
665 665  
666 -[[http:~~/~~/wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction]]
735 +(((
736 +
737 +)))
667 667  
668 -
739 +(((
669 669  **V1.0.**
741 +)))
670 670  
743 +(((
671 671  Release
745 +)))
672 672  
673 673  
748 +== 2.11 ​Battery Analysis ==
674 674  
675 -1.
676 -11. ​Battery Analysis
677 -111. ​Battery Type
750 +=== 2.11.1 ​Battery Type ===
678 678  
752 +(((
679 679  The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
754 +)))
680 680  
681 -
756 +(((
682 682  The battery is designed to last for more than 5 years for the LSN50.
758 +)))
683 683  
760 +(((
761 +(((
762 +The battery-related documents are as below:
763 +)))
764 +)))
684 684  
685 -The battery related documents as below:
686 -
687 -* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
688 -* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet-EN.pdf]] datasheet, [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet_PM-ER18505-S-02-LF_EN.pdf]]
689 -* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
690 -
691 -|(((
692 -JST-XH-2P connector
766 +* (((
767 +[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
693 693  )))
769 +* (((
770 +[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
771 +)))
772 +* (((
773 +[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
774 +)))
694 694  
695 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]
776 + [[image:image-20220610172436-1.png]]
696 696  
697 697  
698 698  
699 -1.
700 -11.
701 -111. ​Battery Note
780 +=== 2.11.2 ​Battery Note ===
702 702  
782 +(((
703 703  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
784 +)))
704 704  
705 705  
706 -1.
707 -11.
708 -111. ​Replace the battery
709 709  
788 +=== 2.11.3 Replace the battery ===
789 +
790 +(((
710 710  If Battery is lower than 2.7v, user should replace the battery of LSE01.
792 +)))
711 711  
712 -
794 +(((
713 713  You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
796 +)))
714 714  
715 -
798 +(((
716 716  The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
800 +)))
717 717  
718 718  
719 719  
720 -
721 -
722 -
723 723  = 3. ​Using the AT Commands =
724 724  
725 725  == 3.1 Access AT Commands ==
... ... @@ -727,13 +727,13 @@
727 727  
728 728  LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
729 729  
730 -[[image:1654501986557-872.png]]
811 +[[image:1654501986557-872.png||height="391" width="800"]]
731 731  
732 732  
733 733  Or if you have below board, use below connection:
734 734  
735 735  
736 -[[image:1654502005655-729.png]]
817 +[[image:1654502005655-729.png||height="503" width="801"]]
737 737  
738 738  
739 739  
... ... @@ -740,7 +740,7 @@
740 740  In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
741 741  
742 742  
743 - [[image:1654502050864-459.png]]
824 + [[image:1654502050864-459.png||height="564" width="806"]]
744 744  
745 745  
746 746  Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
... ... @@ -855,20 +855,38 @@
855 855  
856 856  == 4.1 ​How to change the LoRa Frequency Bands/Region? ==
857 857  
858 -You can follow the instructions for [[how to upgrade image>>path:#3ygebqi]].
939 +(((
940 +You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
859 859  When downloading the images, choose the required image file for download. ​
942 +)))
860 860  
944 +(((
945 +
946 +)))
861 861  
948 +(((
862 862  How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
950 +)))
863 863  
952 +(((
953 +
954 +)))
864 864  
956 +(((
865 865  You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
958 +)))
866 866  
960 +(((
961 +
962 +)))
867 867  
964 +(((
868 868  For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
966 +)))
869 869  
870 870  [[image:image-20220606154726-3.png]]
871 871  
970 +
872 872  When you use the TTN network, the US915 frequency bands use are:
873 873  
874 874  * 903.9 - SF7BW125 to SF10BW125
... ... @@ -881,7 +881,9 @@
881 881  * 905.3 - SF7BW125 to SF10BW125
882 882  * 904.6 - SF8BW500
883 883  
983 +(((
884 884  Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
985 +)))
885 885  
886 886  (% class="box infomessage" %)
887 887  (((
... ... @@ -893,10 +893,17 @@
893 893  **ATZ**
894 894  )))
895 895  
997 +(((
896 896  to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
999 +)))
897 897  
1001 +(((
1002 +
1003 +)))
898 898  
1005 +(((
899 899  The **AU915** band is similar. Below are the AU915 Uplink Channels.
1007 +)))
900 900  
901 901  [[image:image-20220606154825-4.png]]
902 902  
... ... @@ -911,7 +911,9 @@
911 911  
912 912  == 5.2 AT Command input doesn’t work ==
913 913  
1022 +(((
914 914  In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1024 +)))
915 915  
916 916  
917 917  == 5.3 Device rejoin in at the second uplink packet ==
... ... @@ -923,7 +923,9 @@
923 923  
924 924  (% style="color:#4f81bd" %)**Cause for this issue:**
925 925  
1036 +(((
926 926  The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
1038 +)))
927 927  
928 928  
929 929  (% style="color:#4f81bd" %)**Solution: **
... ... @@ -930,7 +930,7 @@
930 930  
931 931  All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
932 932  
933 -[[image:1654500929571-736.png]]
1045 +[[image:1654500929571-736.png||height="458" width="832"]]
934 934  
935 935  
936 936  = 6. ​Order Info =
... ... @@ -955,10 +955,17 @@
955 955  * (% style="color:red" %)**4**(%%): 4000mAh battery
956 956  * (% style="color:red" %)**8**(%%): 8500mAh battery
957 957  
1070 +(% class="wikigeneratedid" %)
1071 +(((
1072 +
1073 +)))
1074 +
958 958  = 7. Packing Info =
959 959  
960 960  (((
961 -**Package Includes**:
1078 +
1079 +
1080 +(% style="color:#037691" %)**Package Includes**:
962 962  )))
963 963  
964 964  * (((
... ... @@ -967,10 +967,8 @@
967 967  
968 968  (((
969 969  
970 -)))
971 971  
972 -(((
973 -**Dimension and weight**:
1090 +(% style="color:#037691" %)**Dimension and weight**:
974 974  )))
975 975  
976 976  * (((
... ... @@ -984,6 +984,8 @@
984 984  )))
985 985  * (((
986 986  Weight / pcs : g
1104 +
1105 +
987 987  )))
988 988  
989 989  = 8. Support =
... ... @@ -990,5 +990,3 @@
990 990  
991 991  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
992 992  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
993 -
994 -
1654506665940-119.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +423.3 KB
Content
image-20220606171726-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +171.0 KB
Content
image-20220610172436-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +370.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0