Changes for page N95S31B -- NB-IoT Temperature & Humidity Sensor User Manual

Last modified by Mengting Qiu on 2024/04/02 16:44

From 120.1 to 119.3 From 125.3 to 125.2

From version 125.2

edited by Xiaoling
on 2022/09/09 15:51

Change comment: There is no comment for this version

To version 120.1

edited by David Huang
on 2022/09/08 15:49

Change comment: Uploaded new attachment "image-20220908154949-1.png", version {1}

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 1 removed)
- image-20220908163102-2.png

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Xiaoling
++XWiki.David

Content

@@ -70,6 +70,7 @@
++
  == 1.3  Specification ==
@@ -78,6 +78,8 @@
  * Supply Voltage: 2.1v ~~ 3.6v
  * Operating Temperature: -40 ~~ 85°C
++
++
  (% style="color:#037691" %)**NB-IoT Spec:**
  * - B1 @H-FDD: 2100MHz
@@ -87,6 +87,8 @@
  * - B20 @H-FDD: 800MHz
  * - B28 @H-FDD: 700MHz
++
++
  (% style="color:#037691" %)**Battery:**
  * Li/SOCI2 un-chargeable battery
@@ -97,6 +97,7 @@
++
  == 1.4  Applications ==
@@ -112,7 +112,6 @@
--
  == 1.5  Pin Definitions & Switch ==
@@ -160,6 +160,7 @@
++
  = 2.  Use N95S31B to communicate with IoT Server =
@@ -350,6 +350,8 @@
  * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   **  (%%) ~/~/ to set UDP server address and port
  * (% style="color:blue" %)**AT+CFM=1       **   (%%) ~/~/ If the server does not respond, this command is unnecessary
++
++
  [[image:1657352391268-297.png]]
@@ -370,6 +370,8 @@
  * (% style="color:blue" %)**AT+PUBTOPIC=f9527                               **(%%)~/~/Set the sending topic of MQTT
  * (% style="color:blue" %)**AT+SUBTOPIC=Ns9527          **(%%)                  ~/~/Set the subscription topic of MQTT
++
++
  [[image:1657352634421-276.png]]
@@ -395,6 +395,8 @@
  * (% style="color:blue" %)**AT+PRO=4   ** (%%)                                          ~/~/ Set to use TCP protocol to uplink
  * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
++
++
  [[image:1657352898400-901.png]]
@@ -413,21 +413,13 @@
  )))
--(((
--(% style="color:red" %)**NOTE: Since firmware version is v1.2:**
--)))
--(((
--(% style="color:red" %)**By default, the device will send an uplink message every 2 hours. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
--)))
--
--
  == 2.3  Uplink Payload ==
  (((
--N95S31B has different working modes for the connections of different types of sensors. This section describes these modes. User can use the AT Command (% style="color:blue" %)**AT+MOD**(%%) to set NBSN95 to different working modes.
++N95S31B has different working mode for the connections of different type of sensors. This section describes these modes. User can use the AT Command (% style="color:blue" %)**AT+MOD**(%%) to set NBSN95 to different working modes.
  )))
@@ -472,17 +472,14 @@
  === 2.3.1  Payload Analyze ===
--==== 2.3.1.1  Before Firmware v1.2 ====
--
--
  N95S31B uplink payload includes in total 21 bytes
--(% border="2" cellspacing="10" style="background-color:#ffffcc; color:green; width:760px" %)
++(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:520px" %)
  |=(% style="width: 60px;" %)(((
  **Size(bytes)**
--)))|=(% style="width: 65px;" %)**6**|=(% style="width: 50px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 75px;" %)**1**|=(% style="width: 59px;" %)1|=(% style="width: 174px;" %)5|=(% style="width: 106px;" %)**2**|=(% style="width: 85px;" %)**2**
--|(% style="width:97px" %)**Value**|(% style="width:65px" %)[[Device ID>>||anchor="H2.3.2A0DeviceID"]]|(% style="width:50px" %)[[Ver>>||anchor="H2.3.3A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.3.4A0BatteryInfo"]]|(% style="width:75px" %)[[Signal Strength>>||anchor="H2.3.5A0SignalStrength"]]|(% style="width:59px" %)MOD 0X01|(% style="width:174px" %)(((
++)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 55px;" %)1|=(% style="width: 115px;" %)5|=(% style="width: 60px;" %)**2**|=(% style="width: 60px;" %)**2**
++|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.3.2A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.3.3A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.3.4A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.3.5A0SignalStrength"]]|(% style="width:123px" %)MOD 0X01|(% style="width:99px" %)(((
  (((
  Reserve/ Same as NBSN95 CFGMOD=1
  )))
@@ -490,7 +490,7 @@
  (((
  No function here.
  )))
--)))|(% style="width:106px" %)(((
++)))|(% style="width:77px" %)(((
  (((
  [[Temperature >>||anchor="H2.3.6A0Temperature26Humidity"]]
  )))
@@ -498,7 +498,7 @@
  (((
  By SHT31
  )))
--)))|(% style="width:85px" %)(((
++)))|(% style="width:80px" %)(((
  (((
  [[Humidity>>||anchor="H2.3.6A0Temperature26Humidity"]]
  )))
@@ -522,60 +522,25 @@
  The payload is ASCII string, representative same HEX: 0x724031607457006e0ccd1b0100dc000ccc00e10186 where:
--* Device ID:  0x724031607457 = 724031607457
++* Device ID: 0x724031607457 = 724031607457
++* Version: 0x006e=110=1.1.0
--* Version:     0x006e=110=1.1.0
--
--* BAT:      0x0ccd = 3277 mV = 3.277V
--
--* Signal:  0x1b = 27
--
--* Model:  0x01 = 1
--
++* BAT: 0x0ccd = 3277 mV = 3.277V
++* Signal: 0x1b = 27
++* Model: 0x01 = 1
  * 0x00dc000ccc= reserve, ignore in N95S31B
++* Temperature by SHT31: 0x00e1 = 225 = 22.5 °C
++* Humidity by SHT31: 0x0186 = 390 = 39.0 %rh
--* Temperature by SHT31:  0x00e1 = 225 = 22.5 °C
--
--* Humidity by SHT31:       0x0186 = 390 = 39.0 %rh
--
  (((
++)))
--
++(((
  )))
--==== 2.3.1.2 Since Firmware v1.2 ====
--In this mode, uplink payload includes 91 bytes in total by default.
--
--Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
--
--|**Size(bytes)**|**8**|2|2|1|1|2|1|2|2|2|4|2|2|4
--|**Value**|Device ID|Ver|BAT|Signal Strength|MOD|TemDS18B20|Interrupt|ADC|SHTTEM|SHTHUM|Time stamp |SHTTEM|SHTHUM|Time stamp .....
--
--If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the N95S31B uplink data.
--
--[[image:image-20220908154949-1.png]]
--
--The payload is ASCII string, representative same HEX:
--
--0x(% style="color:red" %)f868411056758782(% style="color:blue" %)000c(% style="color:green" %)0d0f(% style="color:red" %)0c(% style="color:blue" %)01(% style="color:green" %)0000(% style="color:red" %)00**//0030//**(% style="color:blue" %)**//0114//**(% style="color:red" %)**//0231//**(% style="color:green" %)**//63199d3c//**0113023163199d12//**0113023163199c5e**//0112023763199baa//**0112023263199af6**//0111023b631999a7//**0112023b631998f3**//011202426319983f//**01110242631996eb**//(%%) where:
--
--* (% style="color:red" %) Device ID: f868411056758782 = f868411056758782
--* (% style="color:blue" %) Version: 0x000c=120=1.2
--* (% style="color:green" %)  BAT: 0x0d0f = 3343 mV = 3.343V
--* (% style="color:red" %)  Singal: 0x0c = 12
--* (% style="color:blue" %) Mod: 0x01 = 1
--* TemDS18B20: 0x0000= 0 = 0
--* (% style="color:green" %)Interrupt: 0x00= 0
--* (% style="color:green" %)adc: 0x0030= 48
--* SHTTEM: 0x0114= 276 = 27.6
--* SHTHUM:0x0231 =561=56.1%
--* (% style="color:red" %) Time stamp : 0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
--* (% style="color:red" %)SHTTEM,SHTHUM,Time stamp : 0113023163199d12
--* 8 sets of recorded data: SHTTEM,SHTHUM,Time stamp : //**0113023163199c5e**//,.......
--
  === 2.3.2  Device ID ===
@@ -597,22 +597,10 @@
  (((
  The Device ID is stored in a none-erase area, Upgrade the firmware or run **AT+FDR** won't erase Device ID.
--
--
  )))
--(% style="color:red" %)**NOTE:When the firmware version is v1.2 and later firmware:**
--By default, the Device ID equal to the last 15 bits of IMEI.
--
--User can use **AT+DEUI** to set Device ID
--
--**Example:**
--
--AT+DEUI=868411056754138
--
--
  === 2.3.3  Version Info ===
@@ -758,59 +758,13 @@
  )))
--== 2.5 Humidity and Temperature alarm function ==
--➢ AT Command:
++== 2.5  Battery Analysis ==
--AT+ SHHUM=min,max
--² When min=0, and max≠0, Alarm higher than max
++=== 2.5.1  Battery Type ===
--² When min≠0, and max=0, Alarm lower than min
--² When min≠0 and max≠0, Alarm higher than max or lower than min
--
--Example:
--
--AT+ SHHUM=50,80 ~/~/ Alarm when humidity lower than 50.
--
--
--AT+ SHTEMP=min,max
--
--² When min=0, and max≠0, Alarm higher than max
--
--² When min≠0, and max=0, Alarm lower than min
--
--² When min≠0 and max≠0, Alarm higher than max or lower than min
--
--Example:
--
--AT+ SHTEMP=20,30 ~/~/ Alarm when temperature lower than 20.
--
--== 2.6 Set the number of data to be uploaded and the recording time ==
--
--➢ AT Command:
--
--AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
--
--AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
--
--== 2.7 Read or Clear cached data ==
--
--➢ AT Command:
--
--AT+CDP    ~/~/ Read cached data
--
--[[image:image-20220908163102-2.png]]
--
--AT+CDP=0    ~/~/ Clear cached data
--
--== 2.8  Battery Analysis ==
--
--
--=== 2.8.1  Battery Type ===
--
--
  (((
  The N95S31B battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
  )))
@@ -833,7 +833,7 @@
--=== 2.8.2  Power consumption Analyze ===
++=== 2.5.2  Power consumption Analyze ===
  (((
@@ -845,7 +845,7 @@
  )))
--=== 2.8.3  Battery Note ===
++=== 2.5.3  Battery Note ===
  (((
@@ -854,7 +854,7 @@
--=== 2.8.4  Replace the battery ===
++=== 2.5.4  Replace the battery ===
  (((
@@ -933,24 +933,7 @@
  AT+SERVADDR          : Server Address
--AT+TR      : Get or Set record time
--AT+APN            : Get or set the APN
--
--AT+FBAND          : Get or Set whether to automatically modify the frequency band
--
--AT+DNSCFG         :  Get or Set DNS Server
--
--AT+GETSENSORVALUE   : Returns the current sensor measurement
--
--AT+NOUD      : Get or Set the number of data to be uploaded
--
--AT+CDP     : Read or Clear cached data
--
--AT+SHTEMP: Get or Set alarm of temp
--
--AT+SHHUM: Get or Set alarm of moisture
--
  (% style="color:#037691" %)**COAP Management**
  AT+URI            : Resource parameters
@@ -1077,3 +1077,6 @@
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
++
++
++

image-20220908163102-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.David

Size

...	...	@@ -1,1 +1,0 @@
1		-29.7 KB

Content