Wiki source code of LTS5 LoRa HMI Touch Screen

Version 189.6 by BoYang Xie on 2025/07/09 11:42

version	line-number	content
133.2	1
	2
188.2	3	[[image:image-20241226135550-1.png\|\|data-xwiki-image-style-alignment="center"]]
2.1	4
	5
56.1	6
	7
2.1	8	(% _mstvisible="1" %)
56.1	9	(% _msthash="315238" _msttexthash="18964465" _mstvisible="3" %)Table of Contents:
2.1	10
	11	{{toc/}}
	12
	13
	14
	15
	16
	17
	18
	19
	20	= 1. Introduction =
	21
116.1	22	== 1.1 What is the LTS5 LoRa HMI Touch Screen? ==
2.1	23
56.1	24
116.1	25	The LTS5 is a (% style="color:blue" %)LoRa / LoRaWAN HMI Touch Screen(%%) designed for displaying information in IoT projects. It features a 5.0-inch HMI touch screen and supports Wi-Fi, Bluetooth, and LoRa wireless protocols.
2.1	26
116.1	27	The LTS5 is an open-source software project powered by an ESP32 MCU and a Dragino LA66 LoRa module. The extensive development resources available for ESP32 can significantly reduce development time.
2.1	28
116.1	29	The LTS5's HMI touch screen supports drag-and-drop design, allowing developers to use SquareLine to easily customize the display UI for various applications.
2.1	30
116.1	31	The LA66 LoRa module can be programmed to support either private LoRa protocols or the LoRaWAN protocol.
2.1	32
189.2	33
189.3	34	//Note: Due to the current incomplete functionality, it is not recommended to purchase at this time.//
189.2	35
2.1	36	== 1.2 Features ==
	37
115.1	38
55.1	39	* ESP32-WROOM MCU: 8MB RAM & 16MB ROM
	40	* Dragino LA66 LoRa Module
4.2	41	* Support Private LoRa protocol or LoRaWAN protocol
	42	* Support WiFi & BLE wireless protocol
	43	* 5.0" HMI touch screen
4.6	44	* Support LVGL case. SquareLine program.
4.2	45	* Support RS485 Interface
	46	* Open Source Project
2.1	47	* Wall Attachable.
4.2	48	* 5V DC power
2.1	49	* IP Rating: IP52
	50
116.1	51	== 1.3 Specifications ==
2.1	52
56.1	53
4.9	54	LoRa:
	55
55.1	56	* Frequency Range: 870 MHz ~~ 960 MHz
	57	* TCXO crystal to ensure RF performance on low temperature
	58	* Maximum Power +22 dBm constant RF output
	59	* High sensitivity: -148 dBm
	60	* LoRa Tx Current: <90 mA at +17 dBm, 108 mA at +22 dBm
	61	* LoRa Rx current: <9 mA
4.9	62
4.7	63	WiFi:
	64
	65	* 802.11b/g/n
	66	* Up to 150 Mbps data rate in 802.11n mode
	67	* Support A-MPDU and A-MSDU aggregation
	68	* zero point four μ S protection interval
	69	* Working channel center frequency range: 2412~~2484 MHz
	70
	71	Bluetooth:
	72
	73	* Bluetooth V4.2 BR/EDR and Bluetooth LE standard
	74	* Class-1, Class-2, and Class-3 transmitters.
	75	* AFH
	76	* CVSD and SBC
	77
4.2	78	Display:
2.1	79
4.9	80	* 5.0 Inch , 800 x 480
	81	* IPS Capacitive Touch SCreen
4.11	82	* RGB color.
	83	* Display Area: 120.7*75.80 mm
2.1	84
	85	== 1.4 Power Consumption ==
	86
56.1	87
4.5	88	* External 5V DC power adapter
2.1	89
	90	== 1.5 Storage & Operation Temperature ==
	91
56.1	92
4.10	93	* Operation Temperature: -20 ~~ 70°C (No Dew)
	94	* Storage Temperature: -30 ~~ 70°C (No Dew)
2.1	95
	96	== 1.6 Applications ==
	97
56.1	98
2.1	99	* Smart Buildings & Home Automation
	100	* Logistics and Supply Chain Management
	101	* Smart Metering
	102	* Smart Agriculture
	103	* Smart Cities
	104	* Smart Factory
	105
122.1	106	= 2. Getting Started with 'Hello World' =
2.1	107
5.1	108	== 2.1 About this demo ==
2.1	109
56.1	110
117.1	111	This getting started example demonstrates how to design and deploy a simple display UI for the LTS5 device. The example includes:
2.1	112
117.1	113	* Creating a basic UI with a single button.
	114	* Implementing functionality to navigate the Web UI to a new page when the button is clicked.
	115	* Uploading the UI to the LTS5 device.
56.1	116
117.1	117	By completing this demo, you will gain foundational knowledge for customizing the LTS5 interface and building more advanced IoT applications.
	118
	119
5.1	120	== 2.2 Install Software Running Environment ==
2.1	121
115.1	122
120.1	123	The ESP MCU supports development with ESP-IDF, Arduino, or MicroPython. We use ESP-IDF for compilation and Visual Studio Code (VS Code) as the development environment for this project.
2.1	124
115.1	125
120.1	126	=== 2.2.1 Install VS Code and ESP-IDF extension ===
26.2	127
56.1	128
120.1	129	First, download and install VS Code for your operating system from the Visual Studio Code website: [[Visual Studio Code - Mac, Linux, Windows>>https://code.visualstudio.com/download]].
26.2	130
120.1	131	Next, install the ESP-IDF extension within VS Code. Detailed steps for this process are shown in Image 1.
26.2	132
120.1	133
51.2	134	[[image:image-20240928110211-5.png\|\|height="508" width="866"]]
	135
120.1	136	Image 1: ESP-IDF extension install
26.2	137
	138	Links for reference: [[Install ESP32 ESP-IDF on Windows and Integrate with VS code (esp32tutorials.com)>>url:https://esp32tutorials.com/install-esp32-esp-idf-windows-integrate-vs-code/#:~~:text=In%20this%20tutorial,%20we%20will%20show%20you%20how%20to%20install]]
	139
56.1	140
5.1	141	=== 2.2.2 Install SquareLine Studio ===
2.1	142
56.1	143
125.1	144	Download and install the latest version of [[SquareLine Studio>>https://squareline.io/downloads#lastRelease]] on your computer. It supports Windows, Linux, and Mac OS. The software version we are using here is 1.5.0. See the image below.
2.1	145
133.2	146	[[image:squareline.io_downloads.png\|\|height="888" width="1294"]]
2.1	147
56.1	148
121.1	149	After installation, you can use SquareLine Studio with a PERSONAL license plan. Click LOG IN and create a free account using your email address. Then activate your PERSONAL license plan for free. You don’t need to provide any credit card information. However, the PERSONAL license plan has the following limitations:
120.1	150
121.1	151	* Max. 10 screens
	152	* Max. 150 widgets
	153	* Max. 5 global colors
	154	* Max. 2 themes
	155	* Max. 1 component
120.1	156
121.1	157	== 2.3 Simple usage of SquareLine Studio and exporting UI code ==
2.1	158
56.1	159
131.1	160	Start the SquareLine Studio. The launcher screen appears as shown in the below image. You can create a new project by clicking Create in the top menu. Then select the Desktop tab. Select the development platform, Eclipse with SDL for development on PC.
2.1	161
125.1	162	* In the PROJECT SETTINGS, select LVGL version as 8.3.11 and Resolution as 800 x 480.
	163	* Select the CREATE button to create the new project with the selected settings.
121.1	164
133.2	165	[[image:squareline-studio-launcher-screen.png\|\|height="752" width="1415"]]
26.2	166
	167
131.1	168	Next, you need to configure some additional settings for this project. To do so, select File -> Project Settings as shown in the image below.
	169
26.2	170	[[image:1727229582471-566.png]]
	171
	172
131.1	173	In the PROJECT SETTINGS dialog box, configure/modify the project settings as shown in the image below.
121.1	174
179.1	175	* UI Files Export Path: Select a folder on your computer to store the UI files.
121.1	176	* LVGL Include Path: Set this to lvgl.h
131.1	177	* Click on the APPLY CHANGES button.
121.1	178
51.2	179	[[image:image-20240928105309-4.png\|\|height="526" width="556"]]
	180
26.2	181
131.1	182	Now you can start building the user interface. Follow the steps below:
26.2	183
121.1	184
123.2	185	=== Add widgets ===
26.2	186
123.2	187
180.1	188	After creating a project, a Screen will be automatically added. Its name is Screen1 by default.
	189
131.1	190	To add a widget, navigate to the Widgets panel, and then click on the widget you want to add to the screen. You can reposition the widgets in the screen area by clicking and dragging them. Now add a Label, Button, and Image as shown in the image below. The added widgets are also displayed in the Hierarchy panel.
26.2	191
51.2	192	[[image:image-20240928111412-6.png\|\|height="526" width="864"]]
26.2	193
	194
131.1	195	Then click the Screen widget to add the second screen. After adding the second screen, it will appear in the Screens panel as Screen2.
26.2	196
131.1	197	[[image:Screenshot 2024-12-24 140459.png\|\|height="278" width="290"]]
	198
123.2	199	=== Modify widget properties ===
	200
	201
131.1	202	The area for modifying widgets is called the Inspector panel. The Inspector panel consists of four sections: COMPONENT, <WIDGET>, STYLE SETTINGS, and EVENTS, as shown in the image below. The second section allows you to adjust a widget's layout, size, position, alignment, flags, states, and more. When you select a widget on the screen, the name of this section changes to match the name of the selected widget.
26.2	203
51.2	204	[[image:1727485118799-984.png]]
26.2	205
	206
123.2	207	==== Changing the Button properties ====
122.1	208
123.2	209
131.1	210	Click the Button you have added to the screen. Under the Layout you can change the button's position and size. Use the following settings:
122.1	211
131.1	212	* Flex Flow: No Layout
	213	* Transform:
	214	X**: 331 px
	215	Y**: 203 px
	216	Width**: 100 px
	217	Height**: 50 px
	218	Align**: CENTER
122.1	219
51.2	220	[[image:1727485251053-655.png]]
26.2	221
	222
123.1	223	Next, add a click event to the button. When the button is clicked, an event should trigger to change the current screen (Screen1) to a new screen (Screen2) with a fade effect and the transition from Screen1 to Screen2 should take 500ms.
26.2	224
131.1	225	* Click ADD EVENT button. A new section will appear to configure this event.
26.2	226
131.1	227	[[image:Screenshot 2024-12-24 134937.png\|\|height="80" width="290"]]
	228
	229	* Select CLICKED from the dropdown under Trigger. Choose CHANGE SCREEN under Action, then click the ADD button. A new section will appear to configure the action.
	230
	231	[[image:Screenshot 2024-12-24 134818.png\|\|height="222" width="290"]]
	232
	233	* Select Screen2 under Screen to. Select FADE ON from Fade mode. The default value 500 means the transition takes 500 milliseconds to appear the Screen2.
	234	* Finally, click the ADD button.
	235
51.2	236	[[image:1727485480434-713.png\|\|height="395" width="290"]]
26.2	237
123.2	238	Image 8: Add an event for the button
51.2	239
	240
123.2	241	==== Changing the label properties ====
51.2	242
123.2	243
131.1	244	Click the Label you have added to the screen. Under the Label section, type "Click for Detail" in the Text textbox.
122.1	245
51.2	246	[[image:image-20240928090825-1.png\|\|height="327" width="391"]]
	247
	248
131.1	249	Once you enter the text, it will immediately appear on the label.
51.2	250
131.1	251
123.2	252	==== Changing image properties ====
122.1	253
123.2	254
131.1	255	To use the Image widget, you should first add an image to your project. The image format must be PNG, and its resolution should not exceed 800x480 pixels. There are two ways to add an image file.
51.2	256
131.1	257	One way is to move your image into the folder "…/squareline project/assets/", as shown in the image below.
	258
51.2	259	[[image:image-20240928113424-9.png\|\|height="355" width="505"]]
	260
	261
131.1	262	The other way is to click the "ADD FILE INTO ASSETS" button, then select an image from your computer to import. After adding, you can see the image in the "assets" panel in SquareLine Studio, as shown in the image below.
	263
51.2	264	[[image:image-20240928114139-10.png\|\|height="559" width="810"]]
	265
	266
123.2	267	==== The relationship between widgets ====
51.2	268
123.2	269
123.1	270	Widgets commonly have two types of relationships: parallel and parent-child.
	271
	272	* In a parallel relationship, widgets' positions are determined relative to a shared reference object.
132.1	273	* In a parent-child relationship, any part of the child object outside the parent's boundaries is hidden by default. To make the child object fully visible, you must adjust its position to fit within the parent's range.
123.1	274
51.2	275	[[image:1727486567182-334.png\|\|height="318" width="278"]]
	276
	277
131.1	278	Move the label, Label1 to make it a child of Button1 as shown in the image below.
123.1	279
51.2	280	[[image:image-20240928112001-8.png\|\|height="431" width="796"]]
	281
	282
131.1	283	Then set the X and Y position of the label to 0 as shown in the image below. The label will appear on the button. If you move the button on the screen, the label will move along with it as part of the button.
51.2	284
131.1	285	[[image:Screenshot 2024-12-24 144005.png\|\|height="360" width="290"]]
	286
	287
123.2	288	==== Preview the screen ====
51.2	289
123.2	290
132.1	291	You can test the result by clicking on the PLAY button as shown in the image below. The screen will change into play mode.
122.1	292
51.2	293	[[image:1727487368023-281.png]]
	294
	295
123.1	296	For more information, please visit the official link: [[SquareLine Studio 1.4.2 Documentation ~\| SquareLine Studio>>url:https://docs.squareline.io/docs/squareline/]].
51.2	297
123.1	298
181.1	299	== 2.4 Integrate UI Code into an ESP-IDF Project ==
26.2	300
56.1	301
132.1	302	To integrate, first export the UI code, then make some modifications, and finally relocate the UI code to a specific position within the project.
26.2	303
135.1	304	On the menubar, click Export -> Export UI Files as shown in the image below.
	305
26.2	306	[[image:1727229798126-306.png]]
	307
	308
135.1	309	The exported UI files can be found in your SquareLine project folder as shown in the image below.
	310
	311
51.2	312	[[image:1727229821582-258.png\|\|height="333" width="662"]]
26.2	313
	314
135.1	315	Create a new folder named "ui" at path "basic_prj/app_components/ui/", and copy all the exported UI code into it as shown in the image below.
26.2	316
54.1	317	[[image:image-20240928144830-11.png]]
26.2	318
	319
135.1	320	Open the CMakeLists.txt file and edit it as ahown below.
	321
51.2	322	[[image:1727229892636-154.png\|\|height="521" width="407"]]
26.2	323
	324
135.1	325	Open the main.c file and add two lines of code as shown in the below images.
132.1	326
135.1	327	Add #include "ui.h"
26.2	328
	329	[[image:1727229926561-300.png]]
	330
	331
135.1	332	Add ui_init();
	333
26.2	334	[[image:1727229955611-607.png]]
	335
	336
135.1	337	== 2.5 Brief introduction to the Hello World project ==
56.1	338
2.1	339
135.1	340	The project consists of two screens. The first screen displays the company's logo, the project name, and a button to navigate to the next screen. The second screen provides information about the HMI screen product through an image and includes a button to return to the previous screen.
56.1	341
51.2	342
	343	== 2.6 Test Result ==
	344
56.1	345
135.1	346	By pressing the button located at the bottom right, the screen switches to the next one as expected. This confirms that the UI file has been successfully integrated into the project and is functioning correctly.
2.1	347
135.1	348	Screen 1:
	349
51.2	350	[[image:1727488067077-684.png\|\|height="402" width="574"]]
26.2	351
	352
135.1	353	Screen 2:
	354
51.2	355	[[image:1727488157579-949.png\|\|height="397" width="572"]]
26.2	356
	357
5.1	358	= 3. Example Project 1: LoRa Central Display =
2.1	359
7.1	360	[[image:image-20240916101737-1.png\|\|height="468" width="683"]]
2.1	361
7.1	362
8.1	363	= 4. Example Project 2: LoRaWAN RS485 Alarm =
2.1	364
165.2	365	= 5. Example Project 3: P2P =
164.2	366
	367	The project achieves the function of receiving LoRa P2P messages and displaying them on the screen. The workflow is as follows: A LA66, running a P2P program, sends a message in a particular format via an AT command. Then, the LTS5 receives the message and displays it on the screen.
	368
	369	The project can be found at [[this link>>url:https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main/Example/P2P]].
	370
182.1	371	== 5.1 Firmware Flashing ==
164.2	372
	373
182.1	374	The following software tools are required to flash firmware to the ESP32 and LA66.
164.2	375
182.1	376	* Download the ESP32 firmware flash tool from [[this link>>https://docs.espressif.com/projects/esp-test-tools/en/latest/esp32/production_stage/tools/flash_download_tool.html]].
	377	* Download the LA66 firmware flash tool from [[this link>>https://www.dropbox.com/scl/fo/9kqeqf6wmet10o9hgxuwa/h?rlkey=4ikrg6kg5v0yjxwhp0i37wrv7&e=1&dl=0]].
164.2	378
182.1	379	=== 5.1.1 Upload the Firmware to the ESP32 ===
164.2	380
182.1	381	Open //flash_download_tool.exe// and follow the steps below.
	382
	383	* Chip Type: ESP32-S3
	384	* WorkMode: Develop
	385	* LoadMode: UART
	386	* Click on the OK button.
	387
164.2	388	[[image:1738893226894-758.png\|\|height="170" width="176"]]
	389
182.1	390
	391	In the SPIDownload tab,
	392
188.1	393	* Select the checkboxes for ESP32_LoRaC-P2P_CommonFW_v1.0.0.bin.
	394	* SPI Flashing Config(default configuration):
182.1	395	SPI SPEED**: 40MHz
	396	SPI MODE**: DIO
	397	Check DoNotChgBin** option.
	398	* COM: Select the correct COM port.
	399	* BAUD: 1152000
	400	* Click on the START button.
	401
188.1	402	[[image:image-20250505122103-4.png\|\|height="551" width="705"]]
164.2	403
182.1	404	The progress bar will indicate the firmware update progress and display a FINISH message once the update is complete.
164.2	405
182.1	406
	407	=== 5.1.2 Upload the Firmware to the LA66 ===
	408
	409	Open Dragino_Sensor_Manager_Utility.exe, and then follow the steps below.
	410
	411	* Click on the UART Update Firmware tab.
	412	* Select the correct COM port.
188.1	413	* Click on the Upload_File button and select the LA66_P2P_FW_v1.0.0.bin file.
182.1	414	* Click on the Start button.
	415
164.2	416
182.1	417
188.1	418	[[image:image-20250505121328-2.png]]
164.2	419
182.1	420
188.1	421	[[image:image-20250505121531-3.png]]
	422
182.1	423	(% class="wikigeneratedid" %)
	424	The progress bar will indicate the firmware update progress.
	425
	426
183.1	427	== 5.2 AT commands and LTS5 Panel Data Formats ==
164.2	428
	429	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A801A4CBBB0A8E085C02,0,3
	430
	431	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A802A4CB00,0,3
	432
	433	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A803A4CB00,0,3
	434
	435	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A804A4CB00,0,3
	436
	437	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A805A4CB00,0,3
	438
	439	AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A806A4CB00,0,3
	440
178.1	441	LTS5 panel data format:
164.2	442
178.1	443	~1. AT+SEND=1,01 4b69746368656e2d467269676531FFFF A84041000181D4A8 01 A4CB BB0A 8E08 5C02,0,3
164.2	444
	445	01: encrypt. 1 Byte. 01 ~-~-> no encryption. This 1-byte information is now invalid; simply write 0x01 instead.
	446
	447	4b69746368656e2d467269676531FFFF: Device Name. 16 Bytes. The Device Name for this piece of information is "Kitchen-Frige1," and the subsequent "FFFF" is intended to pad it up to 16 Bytes. The Device Name for this piece of information is 'Kitchen-Frige1,' and the subsequent 'FFFF' is intended to pad it up to 16 Bytes, but it is not necessary as the system can handle shorter names as well.
	448
	449	A84041000181D4A8: Device EUI. 8 Bytes. The last three Bytes will be extracted by the ESP32-S3 and displayed on the screen.
	450
	451	01: Panel Type. 1 Byte. 0x01~-~->Tem & Hum,
	452
	453	0x02~-~->Door,
	454
	455	0x03~-~->Water Leak,
	456
	457	0x04~-~->Occupied,
	458
	459	0x05~-~->Button,
	460
	461	0x06~-~->Alarm,
	462
	463	A4CB: Battery level//. //2 Bytes. Battery Voltage =0xCBA4&0x3FFF=0x0BA4=2980mV
	464
	465	BB0A: The temperature of the built-in sensor in LHT65N.// //2 Bytes. Temperature: 0x0ABB/100=27.47℃
	466
	467	8E08: The temperature of the External temperature sensor.// //2 Bytes. Temperature: 0x088E/100=21.90℃
	468
	469	5C02：The humidity of the built-in sensor in LHT65N. 2 Bytes. Humidity: 0x025C/10=60.4%
	470
	471	2. AT+SEND=1,01 4b69746368656e2d467269676531FFFF A84041000181D4A8 02 A4CB 00,0,3
	472
	473	Specific sections of the data share the same function.
	474
	475	00: Status. 1 Byte//. //If Panel Type is 0x02, Status: 00~-~->Open; 01~-~->Close.
	476
	477	If Panel Type is 0x03, Status: 00~-~->Normal; 01~-~->Water Leaking.
	478
	479	If Panel Type is 0x04, Status: 00~-~->Free; 01~-~->Occupied.
	480
	481	If Panel Type is 0x05, Status: 00~-~->OFF; 01~-~->ON.
	482
	483	If Panel Type is 0x06, Status: 00~-~->OFF; 01~-~->Alarm.
	484
	485	== 5.3 Usage ==
	486
	487	After burning the firmware into LTS5, you can use an LA66 equipped with peer-to-peer firmware to send data to LTS5 via AT commands.
	488
	489	5.3.1 Connect LA66 to the computer, open Serial Port Utility, and send the AT+CFG instruction to check whether the LA66 has downloaded correct program.
	490
	491	[[image:image-20250207143131-11.png\|\|height="527" width="547"]]
	492
	493	5.3.2 Copy an AT instruction example, click "Send" button, then the led in LA66 will flash and the LTS5 will display the LoRa information.
	494
	495	[[image:image-20250207144605-12.png\|\|height="634" width="548"]]
	496
178.1	497	LTS5 receives this message and displays it on its screen as the image below shows.
	498
	499	[[image:image-20250208181700-8.jpeg\|\|height="528" width="704"]]
	500
164.2	501	= 6. Example Project 4: LoRaWAN_CLASS_C =
	502
	503
	504	The project achieves the function of receiving LoRaWAN Class C messages and displaying them on the screen. Note: The Things Network (TTN) needs to enable Class C support, and the LA66 within the LTS5 needs to operate in Class C mode.
	505
	506	The downlink workflow proceeds as follows: The Things Network (TTN) sends a message in a specific format via downlink. Then, a LoRaWAN gateway relays this message to the LTS5. Finally, the LTS5 receives the message and displays it on its screen.
	507
	508	The uplink workflow is as follows: The LA66 within the LTS5 sends a LoRaWAN message, for some reason, to a LoRaWAN gateway, which then forwards it to The Things Network (TTN).
	509
	510	The project can be found at [[this link>>https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main/Example/LoRaWAN_CLASS_C]].
	511
	512	== 6.1 firmware flashing approach ==
	513
165.3	514	The firmware flashing approach is the same as described in section 5.1.
164.2	515
	516	== 6.2 flowchart ==
	517
	518	[[image:image-20250207164320-13.png\|\|height="696" width="1344"]]
	519
	520	== 6.3 Usage ==
	521
165.3	522	This section now describes a process involving TTN downlink panel data that is to be displayed on the LTS5 screen.
164.2	523
	524	6.3.1 Connect LA66 to the computer, open Serial Port Utility, and send the AT+CFG instruction to check whether the LA66 has downloaded correct program.
	525
	526	[[image:image-20250207165702-14.png\|\|height="830" width="563"]]
	527
	528	6.3.2 Switch to Class C using "AT+CLASS=C", and check the class with "AT+CLASS=?".
	529
	530	[[image:image-20250207173212-27.png]]
	531
	532	[[image:image-20250207172246-20.png]]
	533
	534	6.3.3 Verify LA66's join status (in LTS5) with "AT+NJS=?". If not joined, connect manually to LoRaWAN with "AT+JOIN".
	535
	536	[[image:image-20250207172010-19.png]]
	537
	538	[[image:image-20250207171650-17.png]]
	539
	540	6.3.4 After joining, send a message to TTN, such as "AT+SENDB=01,02,8,05820802581ea0a5", to activate communication.
	541
	542	[[image:image-20250207192107-28.png]]
	543
165.3	544	6.3.5 TTN distributes panel data in three phases: DEUI, Dev Name, and Sensor Data. The Dev Name, the last three bytes of the DEUI, and the panel type union together ensure the identification of a panel. Data about the same panel type will update the existing panel display, while data about a different panel type will create a new panel display on the LTS5 screen.
164.2	545
165.3	546	There is an example for TTN downlink.
165.2	547
164.2	548	1. downlink DEUI F1A84041000181D4A8
	549	1. downlink Dev Name F24B69746368656E2D467269676531FFFF
165.2	550	1. downlink Sensor Data 5501A4CBBB0A8E085C02 or 5504A4CB01. Both of them are vaild formats for LTS5. Note: 0x55 as prefix and any other prefix except 0xF1, 0xF2, 0xF3 means downlink is Sensor Data.
164.2	551
178.1	552	[[image:image-20250208175819-1.png\|\|height="503" width="502"]]
	553
	554
	555	[[image:image-20250208175918-2.png\|\|height="505" width="502"]]
	556
	557
	558	[[image:image-20250208180010-3.png\|\|height="507" width="503"]]
	559
	560
	561	[[image:image-20250208181019-4.jpeg\|\|height="592" width="790"]]
	562
	563
	564	[[image:image-20250208181328-7.png\|\|height="505" width="504"]]
	565
	566
	567	[[image:image-20250208181139-5.jpeg\|\|height="594" width="792"]]
	568
	569
165.3	570	= 7. The method for adding a new type of panel to the project =
2.1	571
141.2	572	If you don't have this need, then this part of the content can be ignored.
123.2	573
165.3	574	1. Design a panel in SquareLine Studio, as shown in Image 7.1 below for reference.
75.1	575
	576	[[image:image-20241121113445-1.png\|\|height="584" width="934"]]
	577
165.3	578	Image 7.1: a panel about water_leak
75.1	579
123.2	580
165.3	581	2. Export the UI file: You need to adjust the export path first, then click 'Export -> Export UI Files' on the menu bar. This step was introduced earlier. After that, you can get the UI files as shown in Image 7.2.
75.1	582
	583	[[image:image-20241121141120-4.png\|\|height="383" width="795"]]
	584
165.3	585	Image 7.2: Exported UI files
75.1	586
123.2	587
141.2	588	3. Delete and rename some file. Here are the steps:
75.1	589
135.1	590	Step 1: Delete the 'components' directory.
	591	Step 2: Delete 'filelist.txt'.
	592	Step 3: Delete 'ui_helpers.c' and 'ui_helpers.h'.
	593	Step 4: Rename 'ui_ScreenMain.c' in the 'screens' directory to 'ui_water_leak_style.c'.
	594	Step 5: Rename the 'screens' directory to 'styles'.
75.1	595
	596	[[image:image-20241121151934-10.png\|\|height="303" width="792"]]
	597
165.3	598	image 7.3 rest file (1)
75.1	599
	600	[[image:image-20241121142925-7.png\|\|height="141" width="793"]]
	601
165.3	602	image 7.4 rest file (2)
75.1	603
165.3	604	4. Open the project in VS Code.
75.1	605
165.3	606	5. Add the file include path for water_leak in extra_lib/CMakeLists.txt, as shown in Images 7.5 and 7.6. Its format is similar to that of tem_hum or door."
75.1	607
	608	[[image:image-20241121181957-17.png\|\|height="438" width="516"]]
	609
165.3	610	image 7.5 extra_lib/CMakeLists.txt before adding
75.1	611
	612	[[image:image-20241121182239-18.png\|\|height="520" width="518"]]
	613
165.3	614	image 7.6 extra_lib/CMakeLists.txt after adding
75.1	615
141.2	616	6. Modify the header files included in the fonts and images directories.
75.1	617
165.3	618	Open the fonts/ui_font_Font12.c file, as shown in Image 7.7, and change #include "../ui.h" to #include "../ui_water_leak.h". The modified file is shown in Image 7.8. Other font files need to be modified in the same way.
135.1	619
75.1	620	[[image:image-20241121171629-11.png]]
	621
165.3	622	image 7.7 unmodified font file
75.1	623
	624	[[image:image-20241121171901-12.png]]
	625
165.3	626	image 7.8 modified font file
75.1	627
165.3	628	Open the images/ui_img_battery_empty_png.c file, as shown in Image 7.9, and change #include "../ui.h" to #include "../ui_water_leak.h". The modified file is shown in Image 7.10. Other image files need to be modified in the same way.
75.1	629
	630	[[image:image-20241121172714-13.png]]
	631
165.3	632	image 7.9 unmodified image file
75.1	633
	634	[[image:image-20241121172908-14.png]]
	635
165.3	636	image 7.10 modified image file
75.1	637
165.3	638	7. Modify the ui_water_leak/CMakeLists.txt. Open this file, and modify it as shown in image 7.11 (before) and image 7.12 (after).
75.1	639
	640	[[image:image-20241121180030-15.png]]
	641
165.3	642	image 7.11 ui_water_leak/CMakeLists.txt before modification
75.1	643
	644	[[image:image-20241121180517-16.png]]
	645
165.3	646	image 7.12 ui_water_leak/CMakeLists.txt after modification
75.1	647
	648
165.3	649	8. Modify the ui_water_leak.h file. Images 7.13 and 7.14 show the code before modification, while Images 7.15 and 7.16 show the code after modification.
135.1	650
113.2	651	[[image:image-20241122094200-23.png]]
75.1	652
165.3	653	image 7.13 ui_water_leak.h (1) before modification
75.1	654
113.2	655	[[image:image-20241122094320-24.png\|\|height="852" width="554"]]
75.1	656
165.3	657	image 7.14 ui_water_leak.h (2) before modification
75.1	658
113.2	659	[[image:image-20241122094600-25.png\|\|height="1078" width="554"]]
75.1	660
165.3	661	image 7.15 ui_water_leak.h (1) after modification
75.1	662
113.2	663	[[image:image-20241122094719-26.png\|\|height="941" width="583"]]
75.1	664
165.3	665	image 7.16 ui_water_leak.h (2) before modification
75.1	666
165.3	667	9. Modify ui_water_leak.c file. The image 7.17, 7.18, 7.19 show the code before modification, and the image 7.20, 7.21, 7.22 show the code after modification.
75.1	668
113.2	669	_ui_flag_modify( ((lv_obj_t *)(e->user_data)), LV_OBJ_FLAG_HIDDEN, _UI_MODIFY_FLAG_TOGGLE); This code replaces 4 lines of code in ui_water_leak.c, so it is pasted here for convenience.
75.1	670
113.2	671	[[image:image-20241122102929-27.png\|\|height="619" width="426"]]
	672
165.3	673	image 7.17 ui_water_leak.c (1) before modification
113.2	674
	675	[[image:image-20241122112838-30.png\|\|height="551" width="628"]]
	676
165.3	677	image 7.18 ui_water_leak.c (2) before modification
113.2	678
	679	[[image:image-20241122110815-29.png\|\|height="725" width="712"]]
	680
165.3	681	image 7.19 ui_water_leak.c (3) before modification
113.2	682
	683	[[image:image-20241122113158-31.png\|\|height="872" width="677"]]
	684
165.3	685	image 7.20 ui_water_leak.c (1) after modification
113.2	686
	687	[[image:image-20241122113259-33.png\|\|height="874" width="724"]]
	688
165.3	689	image 7.21 ui_water_leak.c (2) after modification
113.2	690
	691	[[image:image-20241122113359-34.png\|\|height="804" width="746"]]
	692
165.3	693	image 7.22 ui_water_leak.c (3) after modification
113.2	694
165.3	695	10. Modify ui_water_leak_events.h file. The image 7.23 show the code before modification, and the image 7.24 show the code after modification.
113.2	696
	697	[[image:image-20241122134113-35.png\|\|height="380" width="421"]]
	698
165.3	699	image 7.23 ui_water_leak_events_.h before modification
113.2	700
	701	[[image:image-20241122134420-37.png\|\|height="201" width="283"]]
	702
165.3	703	image 7.24 ui_water_leak_events_.h after modification
113.2	704
165.3	705	11. Modify ui_water_leak_events.c file. The image 7.25 show the code before modification, and the image 7.26 show the code after modification.
113.2	706
	707	Step1. '#include "ui.h"'~-~->'#include "ui_water_leak.h"'
	708
	709	Step2. add code below in delete_object() function definition.
	710
	711	panel_all * panel = find_upper_by_SensorPanel(&arr,((lv_obj_t *)(e->user_data~)~)~);
	712
	713	size_t index = panel->panel_obj_index;
	714
	715	deleteElement(&arr, index);
	716
	717	[[image:image-20241122135023-38.png\|\|height="358" width="372"]]
	718
165.3	719	image 7.25 ui_water_leak_events_.c before modification
113.2	720
	721	[[image:image-20241122135258-39.png\|\|height="403" width="559"]]
	722
165.3	723	image 7.26 ui_water_leak_events_.c after modification
113.2	724
123.2	725
141.2	726	12. Modify ui_water_leak_style.c file.
113.2	727
	728	Step1. '#include "../ui.h"'~-~->#include '"../ui_water_leak.h"'
	729
	730	add '#include "../../sort.h"'
	731
	732	add '#include "ui.h"'
	733
	734	[[image:image-20241122141536-41.png\|\|height="361" width="612"]]
	735
165.3	736	image 7.27 ui_water_leak_style.c (1) before modification
113.2	737
	738	[[image:image-20241122142129-42.png\|\|height="386" width="613"]]
	739
165.3	740	image 7.28 ui_water_leak_style.c (1) after modification
113.2	741
123.2	742
113.2	743	Step2. modify 'void ui_ScreenMain_screen_init(void)'~-~->'panel_with_type create_water_leak(uint8_t index)'
	744
165.3	745	delete code as shown in image 7.29
113.2	746
	747	[[image:image-20241122145620-44.png\|\|height="757" width="671"]]
	748
165.3	749	image 7.29 ui_water_leak_style.c (2)
113.2	750
123.2	751
165.3	752	Step3. The image 7.30, 7.31 show the change.
113.2	753
	754	[[image:image-20241122152026-45.png\|\|height="277" width="828"]]
	755
165.3	756	image 7.30 ui_water_leak_style.c (3) before modification
113.2	757
	758	[[image:image-20241122152542-46.png\|\|height="293" width="830"]]
	759
165.3	760	image 7.31 ui_water_leak_style.c (3) after modification
113.2	761
123.2	762
165.3	763	Step4. Copy partly the code in ui_water_leak.c, paste at extra_lib/sort.h(The process is shown in image 7.32, 7.33).
113.2	764
	765	[[image:image-20241122153958-47.png]]
	766
165.3	767	image 7.32 ui_water_leak_style.c (4)
113.2	768
141.2	769
113.2	770	[[image:image-20241122154755-49.png\|\|height="864" width="513"]]
	771
165.3	772	image 7.33 ui_water_leak_style.c (4)
113.2	773
123.2	774
165.3	775	Step5. Delete event function in code which was just pasted in extra_lib/sort.h(The process is shown in image 7.34).
113.2	776
	777	[[image:image-20241122155650-50.png\|\|height="922" width="513"]]
	778
165.3	779	image 7.34 ui_water_leak_style.c (5)
113.2	780
123.2	781
165.3	782	Step6. Add some lines of code in extra_lib/sort.h as shown in image 7.35.
113.2	783
	784	[[image:image-20241122161934-51.png]]
	785
165.3	786	image 7.35
113.2	787
123.2	788
165.3	789	Step7. Add a line of code in extra_lib/sort.h as shown in image 7.36.
113.2	790
	791	[[image:image-20241122162852-53.png\|\|height="330" width="529"]]
	792
165.3	793	image 7.37
113.2	794
123.2	795
165.3	796	Step8. Add some code in ui_water_leak_style.c as shown in image 7.38 from line534 to line 576 in detail.
113.2	797
	798	panel_with_type union_sensor;
	799
	800	union_sensor.panel_type = WATER_LEAK_TYPE;
	801
	802	......
	803
	804	lv_obj_set_x(union_sensor.panel_union.door.ui_PanelSensorDoor, x_by_index(index));
	805
	806	lv_obj_set_y(union_sensor.panel_union.door.ui_PanelSensorDoor, y_by_index(index));
	807
	808	return union_sensor;
	809
141.2	810	[[image:image-20250122173546-6.png\|\|height="777" width="922"]]
113.2	811
165.3	812	image 7.38
113.2	813
123.2	814
141.2	815	13. Rest midification in sort.h file.
113.2	816
165.3	817	In image 7.39 as below, we can see "WATER_LEAK_TYPE" at line 24 and water leak switch status definition at line 32,33, and these are what we need to add in sort.h.
113.2	818
141.2	819	[[image:image-20250122170230-1.png\|\|height="580" width="513"]]
113.2	820
165.3	821	image 7.39 sort.h
113.2	822
141.2	823	13. Modify sort.c file.
	824
	825	Add a line of code ~-~-'#include "ui_water_leak.h"' as shown in image 5.39 line 26.
	826
	827	[[image:image-20250122171910-5.png\|\|height="524" width="510"]]
	828
165.3	829	image 7.40 sort.c (1)
141.2	830
113.2	831	There are still some changes need to be done in sort.c, and omit here for the moment.
	832
	833
141.2	834
165.3	835	= 8. FAQ =
2.1	836
165.3	837	== 8.1 ==
2.1	838
	839
165.3	840	= 9. Order Info =
2.1	841
165.3	842	== 9.1 Part Number ==
2.1	843
56.1	844
4.4	845	Part Number: (% style="color:#4472c4" %)LTS5
2.1	846
	847
165.3	848	== 9.2 Packing Info ==
2.1	849
56.1	850
4.4	851	Package Includes:
2.1	852
4.4	853	* LTS5 HMI Touch Screen
	854	* 5V,2A DC Power Adapter.
	855	* USB Type C Program Cable
2.1	856
165.3	857	= 10. Support =
2.1	858
56.1	859
2.1	860	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	861	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].
	862
165.3	863	= 11. Reference material =
2.1	864
56.1	865
188.2	866	* Datasheet: [[https:~~/~~/www.dropbox.com/scl/fo/fr7wjsdfh9huchg59p7bv/APASCR0elWtp_EbUZ1W9K-A?rlkey=pcuptw3dtg5pw9vgt4ag6hs9z&st=ds6hdztg&dl=0>>https://www.dropbox.com/scl/fo/fr7wjsdfh9huchg59p7bv/APASCR0elWtp_EbUZ1W9K-A?rlkey=pcuptw3dtg5pw9vgt4ag6hs9z&st=ds6hdztg&dl=0]]
188.3	867	* schematic: [[LTS5-V1>>https://www.dropbox.com/scl/fo/grwr5b4x1tk2omyjwg06y/ACleSdi5f7p5zRB2mfPH7CE?rlkey=vhcs83jrj9tkmw8wa9m9wo5rx&st=hkhe3bbj&dl=0]]
141.2	868	* Source Code: [[dragino/LoRa-HMI-Touch-Screen: Open Source LoRa / LoRaWAN HMI Touch Screen Project>>url:https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main]]
4.3	869	* Mechinical
2.1	870
165.3	871	= 12. FCC Warning =
2.1	872
	873
	874	This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:
	875
	876	(1) This device may not cause harmful interference;
	877
	878	(2) this device must accept any interference received,including interference that may cause undesired operation.
	879

Wiki source code of LTS5 LoRa HMI Touch Screen

Applications