Skip to Content
Last modified by Kilight Cao on 2025/07/03 15:34
From version 54.2
edited by Kilight Cao
on 2025/07/03 15:04
Change comment: There is no comment for this version
To version 54.1
edited by Kilight Cao
on 2025/07/03 15:03
Change comment: Uploaded new attachment "image-20221006170630-1.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -2704,11 +2704,16 @@
2704 2704  You can run the AT command **AT+DEBUG** to view the counting event in the serial output. If the firmware is too old and doesn’t support AT+DEBUG, update to the latest firmware first.
2705 2705  
2706 2706  
2707 +== 6.6 Can I use point-to-point communication with LT-22222-L? ==
2708 +
2709 +
2710 +Yes, you can. Please refer to the [[Point-to-Point Communication of LT-22222-L>>https://wiki.dragino.com/xwiki/bin/view/Main/%20Point%20to%20Point%20Communication%20of%20LT-22222-L/]] page. The firmware that supports point-to-point communication can be found [[here>>https://github.com/dragino/LT-22222-L/releases]].
2711 +
2707 2707  
2708 2708  )))
2709 2709  
2710 2710  (((
2711 -== 6.6 Why does the relay output default to an open relay after the LT-22222-LA is powered off? ==
2716 +== 6.7 Why does the relay output default to an open relay after the LT-22222-L is powered off? ==
2712 2712  
2713 2713  
2714 2714  * If the device is not properly shut down and is directly powered off.
... ... @@ -2716,19 +2716,23 @@
2716 2716  * In modes 2 to 5, the DO/RO status and pulse count are saved to flash memory.
2717 2717  * After a restart, the status before the power failure will be read from Flash.
2718 2718  
2719 -== 6.7 Can I set up LT-22222-LA as an NC (Normally Closed) relay? ==
2724 +== 6.8 Can I set up LT-22222-L as an NC (Normally Closed) relay? ==
2720 2720  
2721 2721  
2722 -The LT-22222-LA's built-in relay is Normally Open (NO). You can use an external relay to achieve a Normally Closed (NC) configuration. The circuit diagram is shown below:
2727 +The LT-22222-L's built-in relay is Normally Open (NO). You can use an external relay to achieve a Normally Closed (NC) configuration. The circuit diagram is shown below:
2723 2723  
2724 -[[image:image-20221006170630-1.png]]
2725 2725  
2726 2726  
2727 2727  
2732 +== 6.9 Can the LT-22222-L save the RO state? ==
2728 2728  
2729 -== 6.9 Why does the LT-22222-LA always report 15.585V when measuring the AVI? ==
2730 2730  
2735 +To enable this feature, the firmware version must be 1.6.0 or higher.
2731 2731  
2737 +
2738 +== 6.10 Why does the LT-22222-L always report 15.585V when measuring the AVI? ==
2739 +
2740 +
2732 2732  It is likely that the GND is not connected during the measurement, or that the wire connected to the GND is loose.
2733 2733  
2734 2734