Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,7 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -283,8 +283,6 @@
283	283	[[image:image-20220523174024-3.png]]
284	284
285	285	(((
286		-
287		-
288	288	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
289	289	)))
290	290
...	...	@@ -298,7 +298,6 @@
298	298
299	299	For example if payload is: [[image:image-20220523175847-2.png]]
300	300
301		-
302	302	**The value for the interface is:  **
303	303
304	304	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -330,6 +330,7 @@
330	330	** DO1 LED is off in both case
331	331
332	332
	329	+
333	333	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
334	334
335	335
...	...	@@ -622,6 +622,7 @@
622	622	* **AT+MOD=1 ** **~-~->** The normal working mode
623	623	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
624	624
	622	+
625	625	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
626	626
627	627	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
...	...	@@ -628,7 +628,6 @@
628	628	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
629	629
630	630
631		-
632	632	**AT Command to set Trigger Condition**:
633	633
634	634	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -642,7 +642,6 @@
642	642	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
643	643
644	644
645		-
646	646	(% style="color:#4f81bd" %)**Trigger base on current**:
647	647
648	648	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -652,7 +652,6 @@
652	652	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
653	653
654	654
655		-
656	656	(% style="color:#4f81bd" %)**Trigger base on DI status**:
657	657
658	658	DI status trigger Flag.
...	...	@@ -659,13 +659,12 @@
659	659
660	660	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
661	661
662		-
663	663	**Example:**
664	664
665	665	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
666	666
667	667
668		-**Downlink Command to set Trigger Condition:**
	662	+**Downlink Command to set Trigger Condition**
669	669
670	670	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
671	671
...	...	@@ -694,7 +694,6 @@
694	694	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
695	695
696	696
697		-
698	698	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
699	699
700	700	MOD6 Payload : total 11 bytes payload
...	...	@@ -709,7 +709,6 @@
709	709	* Each bits shows if the corresponding trigger has been configured.
710	710
711	711
712		-
713	713	**Example:**
714	714
715	715	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -722,7 +722,6 @@
722	722	* Each bits shows which status has been trigger on this uplink.
723	723
724	724
725		-
726	726	**Example:**
727	727
728	728	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -735,7 +735,6 @@
735	735	* Each bits shows which status has been trigger on this uplink.
736	736
737	737
738		-
739	739	**Example:**
740	740
741	741	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.