Changes for page LSN50v2-D20-D22-D23 LoRaWAN Temperature Sensor User Manual

Last modified by Xiaoling on 2024/01/17 16:19

From version < 84.8 >

edited by Xiaoling
on 2022/06/07 18:09

To version < 74.12 >

edited by Xiaoling
on 2022/06/07 17:52

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -63,6 +63,10 @@
++
++
++
++
  = 1. Introduction =
  == 1.1 What is LoRaWAN Soil pH Sensor ==
@@ -109,8 +109,6 @@
  * 8500mAh Battery for long term use
--
--
  == 1.3 Probe Specification ==
@@ -132,15 +132,11 @@
  * Length: 3.5 meters
--
--
  == 1.4 Applications ==
  * Smart Agriculture
--
--
  == 1.5 Pin mapping and power on ==
  [[image:1654592472094-134.png]]
@@ -338,6 +338,8 @@
  |0x02|Reply configures info|[[Configure Info Payload>>path:#H3.4GetFirmwareVersionInfo]]
  |0x03|Reply Calibration Info|[[Calibration Payload>>path:#H2.7Calibration]]
++
++
  === 2.3.7 Decode payload in The Things Network ===
  While using TTN network, you can add the payload format to decode the payload.
@@ -550,7 +550,6 @@
--
  == 2.8 Frequency Plans ==
  (((
@@ -747,6 +747,7 @@
  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
++
  === 2.8.5 AS920-923 & AS923-925 (AS923) ===
  (((
@@ -929,37 +929,20 @@
  === 2.8.7 IN865-867 (IN865) ===
--(((
  (% style="color:blue" %)**Uplink:**
--)))
--(((
 .0625 - SF7BW125 to SF12BW125
--)))
--(((
 .4025 - SF7BW125 to SF12BW125
--)))
--(((
 .9850 - SF7BW125 to SF12BW125
--)))
--(((
--
--)))
--(((
  (% style="color:blue" %)**Downlink:**
--)))
--(((
  Uplink channels 1-3 (RX1)
--)))
--(((
 .550 - SF10BW125 (RX2)
--)))
@@ -971,8 +971,6 @@
  * Blink once when device transmit a packet.
--
--
  == 2.10 Firmware Change Log ==
@@ -987,51 +987,26 @@
  = 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
--(((
  Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
--)))
--* (((
--AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
--)))
--* (((
--LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
--)))
++* AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
++* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
--(((
  There are two kinds of commands to configure LSPH01, they are:
--)))
--* (((
--(% style="color:#4f81bd" %)** General Commands**.
--)))
++* (% style="color:#4f81bd" %)** General Commands**.
--(((
  These commands are to configure:
--)))
--* (((
--General system settings like: uplink interval.
--)))
--* (((
--LoRaWAN protocol & radio related command.
--)))
++* General system settings like: uplink interval.
++* LoRaWAN protocol & radio related command.
--(((
  They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--)))
--(((
--
--)))
--* (((
--(% style="color:#4f81bd" %)** Commands special design for LSPH01**
--)))
++* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
--(((
  These commands only valid for LSPH01, as below:
--)))
@@ -1045,27 +1045,16 @@
--(((
  (% style="color:#037691" %)**Downlink Command: 0x01**
--)))
--(((
  Format: Command Code (0x01) followed by 3 bytes time value.
--)))
--(((
  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
--)))
--* (((
--Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
--)))
--* (((
--Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
++* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
++* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--)))
  == 3.2 Set Interrupt Mode ==
@@ -1076,31 +1076,15 @@
  [[image:image-20220607171716-9.png]]
--(((
  (% style="color:#037691" %)**Downlink Command: 0x06**
--)))
--(((
  Format: Command Code (0x06) followed by 3 bytes.
--)))
--(((
  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
--)))
--* (((
--Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
--)))
--* (((
--Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
--)))
++* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
++* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
--(((
--
--)))
--
--
--
  == 3.3 Calibrate Sensor ==
  Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands
@@ -1275,13 +1275,9 @@
  === 4.3.2 Replace the battery ===
--(((
  You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v.  On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
--)))
--(((
  The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
--)))
@@ -1302,9 +1302,7 @@
  (% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
--(((
  In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
--)))
   [[image:1654593712276-618.png]]
@@ -1312,6 +1312,7 @@
  Valid AT Command please check [[Configure Device>>path:#H3.ConfigureLSPH01viaATCommandorLoRaWANDownlink]].
++
  = 6. FAQ =
  == 6.1 How to change the LoRa Frequency Bands/Region ==
@@ -1320,6 +1320,7 @@
  When downloading the images, choose the required image file for download.
++
  = 7. Trouble Shooting =
  == 7.1 AT Commands input doesn’t work ==
@@ -1327,6 +1327,7 @@
  In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
++
  = 8. Order Info =
  Part Number: (% style="color:blue" %)**LSPH01-XX**
@@ -1343,7 +1343,6 @@
  * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--
  = 9. Packing Info =
@@ -1358,7 +1358,6 @@
  * Package Size / pcs : cm
  * Weight / pcs : g
--
  = 10. Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

Changes for page LSN50v2-D20-D22-D23 LoRaWAN Temperature Sensor User Manual

Summary

Details

Applications

Navigation