<
From version < 74.20 >
edited by Xiaoling
on 2022/06/07 17:57
To version < 74.15 >
edited by Xiaoling
on 2022/06/07 17:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1043,24 +1043,16 @@
1043 1043  
1044 1044  
1045 1045  
1046 -(((
1047 1047  (% style="color:#037691" %)**Downlink Command: 0x01**
1048 -)))
1049 1049  
1050 -(((
1051 1051  Format: Command Code (0x01) followed by 3 bytes time value.
1052 -)))
1053 1053  
1054 1054  (((
1055 1055  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
1056 1056  )))
1057 1057  
1058 -* (((
1059 -Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1060 -)))
1061 -* (((
1062 -Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1063 -)))
1054 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1055 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1064 1064  
1065 1065  
1066 1066  
... ... @@ -1073,31 +1073,15 @@
1073 1073  [[image:image-20220607171716-9.png]]
1074 1074  
1075 1075  
1076 -(((
1077 1077  (% style="color:#037691" %)**Downlink Command: 0x06**
1078 -)))
1079 1079  
1080 -(((
1081 1081  Format: Command Code (0x06) followed by 3 bytes.
1082 -)))
1083 1083  
1084 -(((
1085 1085  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1086 -)))
1087 1087  
1088 -* (((
1089 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1090 -)))
1091 -* (((
1092 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1093 -)))
1074 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1075 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1094 1094  
1095 -(((
1096 -
1097 -)))
1098 -
1099 -
1100 -
1101 1101  == 3.3 Calibrate Sensor ==
1102 1102  
1103 1103  Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands
... ... @@ -1272,13 +1272,9 @@
1272 1272  
1273 1273  === ​4.3.2 Replace the battery ===
1274 1274  
1275 -(((
1276 1276  You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
1277 -)))
1278 1278  
1279 -(((
1280 1280  The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
1281 -)))
1282 1282  
1283 1283  
1284 1284  
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0