Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -985,51 +985,26 @@
985	985
986	986	= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
987	987
988		-(((
989	989	Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
990		-)))
991	991
992		-* (((
993		-AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
994		-)))
995		-* (((
996		-LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
997		-)))
	990	+* AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
	991	+* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
998	998
999		-(((
1000	1000	There are two kinds of commands to configure LSPH01, they are:
1001		-)))
1002	1002
1003		-* (((
1004		-(% style="color:#4f81bd" %)** General Commands**.
1005		-)))
	995	+* (% style="color:#4f81bd" %)** General Commands**.
1006	1006
1007		-(((
1008	1008	These commands are to configure:
1009		-)))
1010	1010
1011		-* (((
1012		-General system settings like: uplink interval.
1013		-)))
1014		-* (((
1015		-LoRaWAN protocol & radio related command.
1016		-)))
	999	+* General system settings like: uplink interval.
	1000	+* LoRaWAN protocol & radio related command.
1017	1017
1018		-(((
1019	1019	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
1020		-)))
1021	1021
1022		-(((
1023		-
1024		-)))
1025	1025
1026		-* (((
1027		-(% style="color:#4f81bd" %)** Commands special design for LSPH01**
1028		-)))
	1005	+* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
1029	1029
1030		-(((
1031	1031	These commands only valid for LSPH01, as below:
1032		-)))
1033	1033
1034	1034
1035	1035
...	...	@@ -1043,24 +1043,14 @@
1043	1043
1044	1044
1045	1045
1046		-(((
1047	1047	(% style="color:#037691" %)**Downlink Command: 0x01**
1048		-)))
1049	1049
1050		-(((
1051	1051	Format: Command Code (0x01) followed by 3 bytes time value.
1052		-)))
1053	1053
1054		-(((
1055	1055	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
1056		-)))
1057	1057
1058		-* (((
1059		-Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1060		-)))
1061		-* (((
1062		-Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1063		-)))
	1027	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1028	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1064	1064
1065	1065
1066	1066
...	...	@@ -1073,31 +1073,15 @@
1073	1073	[[image:image-20220607171716-9.png]]
1074	1074
1075	1075
1076		-(((
1077	1077	(% style="color:#037691" %)**Downlink Command: 0x06**
1078		-)))
1079	1079
1080		-(((
1081	1081	Format: Command Code (0x06) followed by 3 bytes.
1082		-)))
1083	1083
1084		-(((
1085	1085	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1086		-)))
1087	1087
1088		-* (((
1089		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1090		-)))
1091		-* (((
1092		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1093		-)))
	1047	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1048	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1094	1094
1095		-(((
1096		-
1097		-)))
1098		-
1099		-
1100		-
1101	1101	== 3.3 Calibrate Sensor ==
1102	1102
1103	1103	Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands