Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -66,7 +66,6 @@
66	66
67	67
68	68
69		-
70	70	= 1. Introduction =
71	71
72	72	== 1.1 ​What is LoRaWAN Soil pH Sensor ==
...	...	@@ -337,7 +337,6 @@
337	337	|0x03|Reply Calibration Info|[[Calibration Payload>>path:#H2.7Calibration]]
338	338
339	339
340		-
341	341	=== 2.3.7 Decode payload in The Things Network ===
342	342
343	343	While using TTN network, you can add the payload format to decode the payload.
...	...	@@ -549,7 +549,6 @@
549	549	* Reply to non-confirmed packet: 14 00
550	550
551	551
552		-
553	553	== 2.8 Frequency Plans ==
554	554
555	555	(((
...	...	@@ -635,8 +635,6 @@
635	635	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
636	636
637	637
638		-
639		-
640	640	=== 2.8.3 CN470-510 (CN470) ===
641	641
642	642	(((
...	...	@@ -971,6 +971,8 @@
971	971	* Blink once when device transmit a packet.
972	972
973	973
	969	+
	970	+
974	974	== 2.10 ​Firmware Change Log ==
975	975
976	976
...	...	@@ -985,26 +985,51 @@
985	985
986	986	= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
987	987
	985	+(((
988	988	Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
	987	+)))
989	989
990		-* AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
991		-* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
	989	+* (((
	990	+AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
	991	+)))
	992	+* (((
	993	+LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
	994	+)))
992	992
	996	+(((
993	993	There are two kinds of commands to configure LSPH01, they are:
	998	+)))
994	994
995		-* (% style="color:#4f81bd" %)** General Commands**.
	1000	+* (((
	1001	+(% style="color:#4f81bd" %)** General Commands**.
	1002	+)))
996	996
	1004	+(((
997	997	These commands are to configure:
	1006	+)))
998	998
999		-* General system settings like: uplink interval.
1000		-* LoRaWAN protocol & radio related command.
	1008	+* (((
	1009	+General system settings like: uplink interval.
	1010	+)))
	1011	+* (((
	1012	+LoRaWAN protocol & radio related command.
	1013	+)))
1001	1001
	1015	+(((
1002	1002	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	1017	+)))
1003	1003
	1019	+(((
	1020	+
	1021	+)))
1004	1004
1005		-* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
	1023	+* (((
	1024	+(% style="color:#4f81bd" %)** Commands special design for LSPH01**
	1025	+)))
1006	1006
	1027	+(((
1007	1007	These commands only valid for LSPH01, as below:
	1029	+)))
1008	1008
1009	1009
1010	1010
...	...	@@ -1018,16 +1018,27 @@
1018	1018
1019	1019
1020	1020
	1043	+(((
1021	1021	(% style="color:#037691" %)**Downlink Command: 0x01**
	1045	+)))
1022	1022
	1047	+(((
1023	1023	Format: Command Code (0x01) followed by 3 bytes time value.
	1049	+)))
1024	1024
	1051	+(((
1025	1025	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	1053	+)))
1026	1026
1027		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1028		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	1055	+* (((
	1056	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1057	+)))
	1058	+* (((
	1059	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1029	1029
1030	1030
	1062	+
	1063	+)))
1031	1031
1032	1032	== 3.2 Set Interrupt Mode ==
1033	1033
...	...	@@ -1038,15 +1038,31 @@
1038	1038	[[image:image-20220607171716-9.png]]
1039	1039
1040	1040
	1074	+(((
1041	1041	(% style="color:#037691" %)**Downlink Command: 0x06**
	1076	+)))
1042	1042
	1078	+(((
1043	1043	Format: Command Code (0x06) followed by 3 bytes.
	1080	+)))
1044	1044
	1082	+(((
1045	1045	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1084	+)))
1046	1046
1047		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1048		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1086	+* (((
	1087	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1088	+)))
	1089	+* (((
	1090	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1091	+)))
1049	1049
	1093	+(((
	1094	+
	1095	+)))
	1096	+
	1097	+
	1098	+
1050	1050	== 3.3 Calibrate Sensor ==
1051	1051
1052	1052	Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands
...	...	@@ -1221,9 +1221,13 @@
1221	1221
1222	1222	=== ​4.3.2 Replace the battery ===
1223	1223
	1273	+(((
1224	1224	You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	1275	+)))
1225	1225
	1277	+(((
1226	1226	The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	1279	+)))
1227	1227
1228	1228
1229	1229
...	...	@@ -1244,7 +1244,9 @@
1244	1244	(% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
1245	1245
1246	1246
	1300	+(((
1247	1247	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
	1302	+)))
1248	1248
1249	1249
1250	1250	[[image:1654593712276-618.png]]
...	...	@@ -1286,6 +1286,8 @@
1286	1286	* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1287	1287	* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1288	1288
	1344	+
	1345	+
1289	1289	= 9. ​Packing Info =
1290	1290
1291	1291
...	...	@@ -1300,6 +1300,9 @@
1300	1300	* Package Size / pcs : cm
1301	1301	* Weight / pcs : g
1302	1302
	1360	+
	1361	+
	1362	+
1303	1303	= 10. ​Support =
1304	1304
1305	1305	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.