Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -985,26 +985,51 @@
985	985
986	986	= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
987	987
	988	+(((
988	988	Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
	990	+)))
989	989
990		-* AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
991		-* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
	992	+* (((
	993	+AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
	994	+)))
	995	+* (((
	996	+LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
	997	+)))
992	992
	999	+(((
993	993	There are two kinds of commands to configure LSPH01, they are:
	1001	+)))
994	994
995		-* (% style="color:#4f81bd" %)** General Commands**.
	1003	+* (((
	1004	+(% style="color:#4f81bd" %)** General Commands**.
	1005	+)))
996	996
	1007	+(((
997	997	These commands are to configure:
	1009	+)))
998	998
999		-* General system settings like: uplink interval.
1000		-* LoRaWAN protocol & radio related command.
	1011	+* (((
	1012	+General system settings like: uplink interval.
	1013	+)))
	1014	+* (((
	1015	+LoRaWAN protocol & radio related command.
	1016	+)))
1001	1001
	1018	+(((
1002	1002	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	1020	+)))
1003	1003
	1022	+(((
	1023	+
	1024	+)))
1004	1004
1005		-* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
	1026	+* (((
	1027	+(% style="color:#4f81bd" %)** Commands special design for LSPH01**
	1028	+)))
1006	1006
	1030	+(((
1007	1007	These commands only valid for LSPH01, as below:
	1032	+)))
1008	1008
1009	1009
1010	1010
...	...	@@ -1018,14 +1018,24 @@
1018	1018
1019	1019
1020	1020
	1046	+(((
1021	1021	(% style="color:#037691" %)**Downlink Command: 0x01**
	1048	+)))
1022	1022
	1050	+(((
1023	1023	Format: Command Code (0x01) followed by 3 bytes time value.
	1052	+)))
1024	1024
	1054	+(((
1025	1025	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	1056	+)))
1026	1026
1027		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1028		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	1058	+* (((
	1059	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1060	+)))
	1061	+* (((
	1062	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	1063	+)))
1029	1029
1030	1030
1031	1031
...	...	@@ -1038,14 +1038,24 @@
1038	1038	[[image:image-20220607171716-9.png]]
1039	1039
1040	1040
	1076	+(((
1041	1041	(% style="color:#037691" %)**Downlink Command: 0x06**
	1078	+)))
1042	1042
	1080	+(((
1043	1043	Format: Command Code (0x06) followed by 3 bytes.
	1082	+)))
1044	1044
	1084	+(((
1045	1045	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1086	+)))
1046	1046
1047		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1048		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1088	+* (((
	1089	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1090	+)))
	1091	+* (((
	1092	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1093	+)))
1049	1049
1050	1050	== 3.3 Calibrate Sensor ==
1051	1051