Last modified by Xiaoling on 2024/01/17 16:19
<
From version < 73.4 >
edited by Xiaoling
on 2022/06/07 17:24
To version < 78.1 >
edited by Xiaoling
on 2022/06/07 18:00
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -64,24 +64,29 @@
64 64  
65 65  
66 66  
67 -
68 -
69 -
70 -
71 -
72 72  = 1. Introduction =
73 73  
74 74  == 1.1 ​What is LoRaWAN Soil pH Sensor ==
75 75  
71 +(((
76 76  The Dragino LSPH01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil pH Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
73 +)))
77 77  
75 +(((
78 78  LSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:#4f81bd" %)pH (%%)**with high accuracy and stable value. The LSPH01 probe can be buried into soil for long time use.
77 +)))
79 79  
79 +(((
80 80  The LoRa wireless technology used in LSPH01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
81 +)))
81 81  
83 +(((
82 82  LSPH01 is powered by (% style="color:#4f81bd" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
85 +)))
83 83  
87 +(((
84 84  Each LSPH01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
89 +)))
85 85  
86 86  
87 87  [[image:1654592435432-887.png]]
... ... @@ -104,9 +104,6 @@
104 104  * IP68 rate for the Sensor Probe
105 105  * 8500mAh Battery for long term use
106 106  
107 -
108 -
109 -
110 110  == 1.3 Probe Specification ==
111 111  
112 112  
... ... @@ -127,16 +127,10 @@
127 127  * IP68 Protection
128 128  * Length: 3.5 meters
129 129  
130 -
131 -
132 -
133 133  == 1.4 ​Applications ==
134 134  
135 135  * Smart Agriculture
136 136  
137 -
138 -
139 -
140 140  == 1.5 Pin mapping and power on ==
141 141  
142 142  [[image:1654592472094-134.png]]
... ... @@ -215,7 +215,9 @@
215 215  [[image:image-20220607170442-2.png]]
216 216  
217 217  
214 +(((
218 218  (% style="color:blue" %)**Step 3**(%%)**:** The LSPH01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
216 +)))
219 219  
220 220  [[image:1654592697690-910.png]]
221 221  
... ... @@ -223,11 +223,17 @@
223 223  
224 224  == 2.3 ​Uplink Payload ==
225 225  
224 +(((
226 226  LSPH01 will uplink payload via LoRaWAN with below payload format: 
226 +)))
227 227  
228 +(((
228 228  Uplink payload includes in total 11 bytes.
230 +)))
229 229  
232 +(((
230 230  Normal uplink payload:
234 +)))
231 231  
232 232  (% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
233 233  |(((
... ... @@ -311,18 +311,21 @@
311 311  
312 312  === 2.3.6 Message Type ===
313 313  
318 +(((
314 314  For a normal uplink payload, the message type is always 0x01.
320 +)))
315 315  
322 +(((
316 316  Valid Message Type:
324 +)))
317 317  
318 318  
319 319  (% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
320 -|**Message Type Code**|**Description**|**Payload**
328 +|=**Message Type Code**|=**Description**|=**Payload**
321 321  |0x01|Normal Uplink|[[Normal Uplink Payload>>path:#H2.3200BUplinkPayload]]
322 322  |0x02|Reply configures info|[[Configure Info Payload>>path:#H3.4GetFirmwareVersionInfo]]
323 323  |0x03|Reply Calibration Info|[[Calibration Payload>>path:#H2.7Calibration]]
324 324  
325 -
326 326  === 2.3.7 Decode payload in The Things Network ===
327 327  
328 328  While using TTN network, you can add the payload format to decode the payload.
... ... @@ -348,12 +348,21 @@
348 348  
349 349  == 2.5 ​Show Data in DataCake IoT Server ==
350 350  
358 +(((
351 351  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
360 +)))
352 352  
362 +(((
363 +
364 +)))
353 353  
366 +(((
354 354  (% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
368 +)))
355 355  
370 +(((
356 356  (% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
372 +)))
357 357  
358 358  
359 359  [[image:1654592790040-760.png]]
... ... @@ -376,9 +376,13 @@
376 376  [[image:1654592856403-259.png]]
377 377  
378 378  
395 +(((
379 379  (% style="color:blue" %)**Step 5**(%%)**: add payload decode**
397 +)))
380 380  
399 +(((
381 381  Download Datacake decoder from: [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Decoder/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSNPK01/Decoder/]]
401 +)))
382 382  
383 383  
384 384  [[image:1654592878525-845.png]]
... ... @@ -401,8 +401,10 @@
401 401  === 2.6.1 Before measurement ===
402 402  
403 403  (((
424 +(((
404 404  If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
405 405  )))
427 +)))
406 406  
407 407  
408 408  
... ... @@ -409,24 +409,45 @@
409 409  === 2.6.2 Measurement ===
410 410  
411 411  
434 +(((
412 412  (% style="color:#4f81bd" %)**Measurement the soil surface:**
436 +)))
413 413  
438 +(((
414 414  [[image:1654592946732-634.png]]
440 +)))
415 415  
442 +(((
416 416  Choose the proper measuring position. Split the surface soil according to the measured deep.
444 +)))
417 417  
446 +(((
418 418  Put pure water, or rainwater to make the soil of measurement point to moist mud. Remove rocks or hard things.
448 +)))
419 419  
450 +(((
420 420  Slowly insert the probe to the measure point. Don’t use large force which will break the probe. Make sure not shake when inserting.
452 +)))
421 421  
454 +(((
422 422  Put soil over the probe after insert. And start to measure.
456 +)))
423 423  
458 +(((
459 +
460 +)))
424 424  
462 +(((
425 425  (% style="color:#4f81bd" %)**Measurement inside soil:**
464 +)))
426 426  
466 +(((
427 427  Dig a hole with diameter > 20CM.
468 +)))
428 428  
470 +(((
429 429  Insert the probe inside, method like measure the surface.
472 +)))
430 430  
431 431  
432 432  
... ... @@ -456,9 +456,13 @@
456 456  
457 457  == 2.7 Calibration ==
458 458  
502 +(((
459 459  User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
504 +)))
460 460  
506 +(((
461 461  After stable, user can use below command to calibrate.
508 +)))
462 462  
463 463  [[image:image-20220607171149-4.png]]
464 464  
... ... @@ -465,7 +465,7 @@
465 465  
466 466  (% style="color:#037691" %)**Calibration Payload**
467 467  
468 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
515 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
469 469  |(((
470 470  **Size**
471 471  
... ... @@ -493,7 +493,6 @@
493 493  * Reply to the confirmation package: 14 01
494 494  * Reply to non-confirmed packet: 14 00
495 495  
496 -
497 497  == 2.8 Frequency Plans ==
498 498  
499 499  (((
... ... @@ -503,32 +503,61 @@
503 503  
504 504  === 2.8.1 EU863-870 (EU868) ===
505 505  
552 +(((
506 506  (% style="color:blue" %)**Uplink:**
554 +)))
507 507  
556 +(((
508 508  868.1 - SF7BW125 to SF12BW125
558 +)))
509 509  
560 +(((
510 510  868.3 - SF7BW125 to SF12BW125 and SF7BW250
562 +)))
511 511  
564 +(((
512 512  868.5 - SF7BW125 to SF12BW125
566 +)))
513 513  
568 +(((
514 514  867.1 - SF7BW125 to SF12BW125
570 +)))
515 515  
572 +(((
516 516  867.3 - SF7BW125 to SF12BW125
574 +)))
517 517  
576 +(((
518 518  867.5 - SF7BW125 to SF12BW125
578 +)))
519 519  
580 +(((
520 520  867.7 - SF7BW125 to SF12BW125
582 +)))
521 521  
584 +(((
522 522  867.9 - SF7BW125 to SF12BW125
586 +)))
523 523  
588 +(((
524 524  868.8 - FSK
590 +)))
525 525  
592 +(((
593 +
594 +)))
526 526  
596 +(((
527 527  (% style="color:blue" %)**Downlink:**
598 +)))
528 528  
600 +(((
529 529  Uplink channels 1-9 (RX1)
602 +)))
530 530  
604 +(((
531 531  869.525 - SF9BW125 (RX2 downlink only)
606 +)))
532 532  
533 533  
534 534  
... ... @@ -549,50 +549,91 @@
549 549  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
550 550  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
551 551  
552 -
553 -
554 554  === 2.8.3 CN470-510 (CN470) ===
555 555  
629 +(((
556 556  Used in China, Default use CHE=1
631 +)))
557 557  
633 +(((
558 558  (% style="color:blue" %)**Uplink:**
635 +)))
559 559  
637 +(((
560 560  486.3 - SF7BW125 to SF12BW125
639 +)))
561 561  
641 +(((
562 562  486.5 - SF7BW125 to SF12BW125
643 +)))
563 563  
645 +(((
564 564  486.7 - SF7BW125 to SF12BW125
647 +)))
565 565  
649 +(((
566 566  486.9 - SF7BW125 to SF12BW125
651 +)))
567 567  
653 +(((
568 568  487.1 - SF7BW125 to SF12BW125
655 +)))
569 569  
657 +(((
570 570  487.3 - SF7BW125 to SF12BW125
659 +)))
571 571  
661 +(((
572 572  487.5 - SF7BW125 to SF12BW125
663 +)))
573 573  
665 +(((
574 574  487.7 - SF7BW125 to SF12BW125
667 +)))
575 575  
669 +(((
670 +
671 +)))
576 576  
673 +(((
577 577  (% style="color:blue" %)**Downlink:**
675 +)))
578 578  
677 +(((
579 579  506.7 - SF7BW125 to SF12BW125
679 +)))
580 580  
681 +(((
581 581  506.9 - SF7BW125 to SF12BW125
683 +)))
582 582  
685 +(((
583 583  507.1 - SF7BW125 to SF12BW125
687 +)))
584 584  
689 +(((
585 585  507.3 - SF7BW125 to SF12BW125
691 +)))
586 586  
693 +(((
587 587  507.5 - SF7BW125 to SF12BW125
695 +)))
588 588  
697 +(((
589 589  507.7 - SF7BW125 to SF12BW125
699 +)))
590 590  
701 +(((
591 591  507.9 - SF7BW125 to SF12BW125
703 +)))
592 592  
705 +(((
593 593  508.1 - SF7BW125 to SF12BW125
707 +)))
594 594  
709 +(((
595 595  505.3 - SF12BW125 (RX2 downlink only)
711 +)))
596 596  
597 597  
598 598  
... ... @@ -617,112 +617,219 @@
617 617  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
618 618  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
619 619  
620 -
621 -
622 622  === 2.8.5 AS920-923 & AS923-925 (AS923) ===
623 623  
738 +(((
624 624  (% style="color:blue" %)**Default Uplink channel:**
740 +)))
625 625  
742 +(((
626 626  923.2 - SF7BW125 to SF10BW125
744 +)))
627 627  
746 +(((
628 628  923.4 - SF7BW125 to SF10BW125
748 +)))
629 629  
750 +(((
751 +
752 +)))
630 630  
754 +(((
631 631  (% style="color:blue" %)**Additional Uplink Channel**:
756 +)))
632 632  
758 +(((
633 633  (OTAA mode, channel added by JoinAccept message)
760 +)))
634 634  
762 +(((
763 +
764 +)))
635 635  
766 +(((
636 636  (% style="color:blue" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
768 +)))
637 637  
770 +(((
638 638  922.2 - SF7BW125 to SF10BW125
772 +)))
639 639  
774 +(((
640 640  922.4 - SF7BW125 to SF10BW125
776 +)))
641 641  
778 +(((
642 642  922.6 - SF7BW125 to SF10BW125
780 +)))
643 643  
782 +(((
644 644  922.8 - SF7BW125 to SF10BW125
784 +)))
645 645  
786 +(((
646 646  923.0 - SF7BW125 to SF10BW125
788 +)))
647 647  
790 +(((
648 648  922.0 - SF7BW125 to SF10BW125
792 +)))
649 649  
794 +(((
795 +
796 +)))
650 650  
798 +(((
651 651  (% style="color:blue" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
800 +)))
652 652  
802 +(((
653 653  923.6 - SF7BW125 to SF10BW125
804 +)))
654 654  
806 +(((
655 655  923.8 - SF7BW125 to SF10BW125
808 +)))
656 656  
810 +(((
657 657  924.0 - SF7BW125 to SF10BW125
812 +)))
658 658  
814 +(((
659 659  924.2 - SF7BW125 to SF10BW125
816 +)))
660 660  
818 +(((
661 661  924.4 - SF7BW125 to SF10BW125
820 +)))
662 662  
822 +(((
663 663  924.6 - SF7BW125 to SF10BW125
824 +)))
664 664  
826 +(((
827 +
828 +)))
665 665  
830 +(((
666 666  (% style="color:blue" %)**Downlink:**
832 +)))
667 667  
834 +(((
668 668  Uplink channels 1-8 (RX1)
836 +)))
669 669  
838 +(((
670 670  923.2 - SF10BW125 (RX2)
840 +)))
671 671  
672 672  
673 673  
674 674  === 2.8.6 KR920-923 (KR920) ===
675 675  
846 +(((
676 676  (% style="color:blue" %)**Default channel:**
848 +)))
677 677  
850 +(((
678 678  922.1 - SF7BW125 to SF12BW125
852 +)))
679 679  
854 +(((
680 680  922.3 - SF7BW125 to SF12BW125
856 +)))
681 681  
858 +(((
682 682  922.5 - SF7BW125 to SF12BW125
860 +)))
683 683  
862 +(((
863 +
864 +)))
684 684  
866 +(((
685 685  (% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
868 +)))
686 686  
870 +(((
687 687  922.1 - SF7BW125 to SF12BW125
872 +)))
688 688  
874 +(((
689 689  922.3 - SF7BW125 to SF12BW125
876 +)))
690 690  
878 +(((
691 691  922.5 - SF7BW125 to SF12BW125
880 +)))
692 692  
882 +(((
693 693  922.7 - SF7BW125 to SF12BW125
884 +)))
694 694  
886 +(((
695 695  922.9 - SF7BW125 to SF12BW125
888 +)))
696 696  
890 +(((
697 697  923.1 - SF7BW125 to SF12BW125
892 +)))
698 698  
894 +(((
699 699  923.3 - SF7BW125 to SF12BW125
896 +)))
700 700  
898 +(((
899 +
900 +)))
701 701  
902 +(((
702 702  (% style="color:blue" %)**Downlink:**
904 +)))
703 703  
906 +(((
704 704  Uplink channels 1-7(RX1)
908 +)))
705 705  
910 +(((
706 706  921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
912 +)))
707 707  
708 708  
709 709  
710 710  === 2.8.7 IN865-867 (IN865) ===
711 711  
918 +(((
712 712  (% style="color:blue" %)**Uplink:**
920 +)))
713 713  
922 +(((
714 714  865.0625 - SF7BW125 to SF12BW125
924 +)))
715 715  
926 +(((
716 716  865.4025 - SF7BW125 to SF12BW125
928 +)))
717 717  
930 +(((
718 718  865.9850 - SF7BW125 to SF12BW125
932 +)))
719 719  
934 +(((
935 +
936 +)))
720 720  
938 +(((
721 721  (% style="color:blue" %)**Downlink:**
940 +)))
722 722  
942 +(((
723 723  Uplink channels 1-3 (RX1)
944 +)))
724 724  
946 +(((
725 725  866.550 - SF10BW125 (RX2)
948 +)))
726 726  
727 727  
728 728  
... ... @@ -734,7 +734,6 @@
734 734  * Blink once when device transmit a packet.
735 735  
736 736  
737 -
738 738  == 2.10 ​Firmware Change Log ==
739 739  
740 740  
... ... @@ -749,26 +749,51 @@
749 749  
750 750  = 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
751 751  
974 +(((
752 752  Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
976 +)))
753 753  
754 -* AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
755 -* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
978 +* (((
979 +AT Command Connection: See [[FAQ>>path:#H6.FAQ]].
980 +)))
981 +* (((
982 +LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>path:/xwiki/bin/view/Main/]]
983 +)))
756 756  
985 +(((
757 757  There are two kinds of commands to configure LSPH01, they are:
987 +)))
758 758  
759 -* (% style="color:#4f81bd" %)** General Commands**.
989 +* (((
990 +(% style="color:#4f81bd" %)** General Commands**.
991 +)))
760 760  
993 +(((
761 761  These commands are to configure:
995 +)))
762 762  
763 -* General system settings like: uplink interval.
764 -* LoRaWAN protocol & radio related command.
997 +* (((
998 +General system settings like: uplink interval.
999 +)))
1000 +* (((
1001 +LoRaWAN protocol & radio related command.
1002 +)))
765 765  
1004 +(((
766 766  They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
1006 +)))
767 767  
1008 +(((
1009 +
1010 +)))
768 768  
769 -* (% style="color:#4f81bd" %)** Commands special design for LSPH01**
1012 +* (((
1013 +(% style="color:#4f81bd" %)** Commands special design for LSPH01**
1014 +)))
770 770  
1016 +(((
771 771  These commands only valid for LSPH01, as below:
1018 +)))
772 772  
773 773  
774 774  
... ... @@ -782,16 +782,28 @@
782 782  
783 783  
784 784  
1032 +(((
785 785  (% style="color:#037691" %)**Downlink Command: 0x01**
1034 +)))
786 786  
1036 +(((
787 787  Format: Command Code (0x01) followed by 3 bytes time value.
1038 +)))
788 788  
1040 +(((
789 789  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
1042 +)))
790 790  
791 -* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
792 -* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1044 +* (((
1045 +Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1046 +)))
1047 +* (((
1048 +Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
793 793  
794 794  
1051 +
1052 +)))
1053 +
795 795  == 3.2 Set Interrupt Mode ==
796 796  
797 797  Feature, Set Interrupt mode for GPIO_EXIT.
... ... @@ -801,17 +801,31 @@
801 801  [[image:image-20220607171716-9.png]]
802 802  
803 803  
1063 +(((
804 804  (% style="color:#037691" %)**Downlink Command: 0x06**
1065 +)))
805 805  
1067 +(((
806 806  Format: Command Code (0x06) followed by 3 bytes.
1069 +)))
807 807  
1071 +(((
808 808  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1073 +)))
809 809  
810 -* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
811 -* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1075 +* (((
1076 +Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1077 +)))
1078 +* (((
1079 +Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1080 +)))
812 812  
1082 +(((
1083 +
1084 +)))
813 813  
814 814  
1087 +
815 815  == 3.3 Calibrate Sensor ==
816 816  
817 817  Detail See [[Calibration Guide>>path:#H2.7Calibration]] for the user of 0x13 and 0x14 downlink commands
... ... @@ -986,9 +986,13 @@
986 986  
987 987  === ​4.3.2 Replace the battery ===
988 988  
1262 +(((
989 989  You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
1264 +)))
990 990  
1266 +(((
991 991  The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
1268 +)))
992 992  
993 993  
994 994  
... ... @@ -1009,7 +1009,9 @@
1009 1009  (% style="background-color:yellow" %)** USB TTL RXD  <~-~-~-~-> UART_TXD**
1010 1010  
1011 1011  
1289 +(((
1012 1012  In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
1291 +)))
1013 1013  
1014 1014  
1015 1015   [[image:1654593712276-618.png]]
... ... @@ -1051,8 +1051,6 @@
1051 1051  * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1052 1052  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1053 1053  
1054 -
1055 -
1056 1056  = 9. ​Packing Info =
1057 1057  
1058 1058  
... ... @@ -1067,8 +1067,6 @@
1067 1067  * Package Size / pcs : cm
1068 1068  * Weight / pcs : g
1069 1069  
1070 -
1071 -
1072 1072  = 10. ​Support =
1073 1073  
1074 1074  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0