LSN50 & LSN50-V2 - LoRaWAN Sensor Node User Manual

(% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||height="15" role="presentation" title="Click and drag to move" width="15"]]

20

)))

21

= 1. Introduction =

== 1.1 What is LSN50 LoRa Sensor Node ==

(((

(((

LSN50 is a Long Range LoRaWAN Sensor Node. It is designed for (% style="color:#4472c4" %)**outdoor data logging **(%%)and powered by (% style="color:#4472c4" %)**Li/SOCl2 battery**(%%) for long term use and secure data transmission. It is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It helps users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

)))

(((

It is based on SX1276/SX1278 allows the user to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

(% style="color:#4472c4" %)**LSN50**(%%) uses STM32l0x chip from ST, STML0x is the (% style="color:#4472c4" %)**ultra-low-power**(%%) STM32L072xx microcontrollers incorporate the connectivity power of the universal serial bus (USB 2.0 crystal-less) with the high-performance ARM® Cortex®-M0+ 32-bit RISC core operating at a 32 MHz frequency, a memory protection unit (MPU), high-speed embedded memories (192 Kbytes of Flash program memory, 6 Kbytes of data EEPROM and 20 Kbytes of RAM) plus an extensive range of enhanced I/Os and peripherals.

)))

(((

LSN50 is an (% style="color:#4472c4" %)**open source product**(%%), it is based on the STM32Cube HAL drivers and lots of libraries can be found in ST site for rapid development.

)))

)))

[[image:1656294562709-486.png]]

== 1.2 Specifications ==

62

63

64

(% style="color:#037691" %)**Micro Controller:**

* STM32L072CZT6 MCU

* MCU: STM32L072CZT6

* Flash: 192KB

* RAM: 20KB

* EEPROM: 6KB

* Clock Speed: 32Mhz

(% style="color:#037691" %)**Common DC Characteristics:**

74

75

* Supply Voltage: 2.1v ~~ 3.6v

76

* Operating Temperature: -40 ~~ 85°C

77

* I/O pins: Refer to STM32L072 datasheet

78

79

(% style="color:#037691" %)**LoRa Spec:**

* Frequency Range,

** Band 1 (HF): 862 ~~ 1020 Mhz

or

*

** Band 2 (LF): 410 ~~ 528 Mhz

89

* 168 dB maximum link budget.

90

* +20 dBm - 100 mW constant RF output vs.

91

* +14 dBm high efficiency PA.

92

* Programmable bit rate up to 300 kbps.

93

* High sensitivity: down to -148 dBm.

94

* Bullet-proof front end: IIP3 = -12.5 dBm.

95

* Excellent blocking immunity.

96

* Low RX current of 10.3 mA, 200 nA register retention.

97

* Fully integrated synthesizer with a resolution of 61 Hz .

98

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

99

* Built-in bit synchronizer for clock recovery.

100

* Preamble detection.

101

* 127 dB Dynamic Range RSSI.

102

* Automatic RF Sense and CAD with ultra-fast AFC.

103

* Packet engine up to 256 bytes with CRC.

104

* LoRaWAN 1.0.2 Specification

105

106

(% style="color:#037691" %)**Battery:**

107

108

* Li/SOCI2 un-chargeable battery

109

* Capacity: 4000mAh

110

* Self Discharge: <1% / Year @ 25°C

111

* Max continuously current: 130mA

112

* Max boost current: 2A, 1 second

113

114

(% style="color:#037691" %)**Power Consumption**

115

116

* STOP Mode: 2.7uA @ 3.3v

117

* LoRa Transmit Mode: 125mA @ 20dBm 44mA @ 14dBm

== 1.3 Features ==

* LoRaWAN 1.0.3 Class A, Class C

122

* STM32L072CZT6 MCU

123

* SX1276/78 Wireless Chip

124

* Pre-load bootloader on USART1/USART2

125

* MDK-ARM Version 5.24a IDE

126

* I2C, LPUSART1, USB, SPI2

127

* 3x12bit ADC, 1x12bit DAC

* 20xDigital I/Os

* LoRa™ Modem

* Preamble detection

* Baud rate configurable

132

* CN470/EU433/KR920/US915/IN865

133

* EU868/AS923/AU915

134

* Open-source hardware / software

135

* Available Band:433/868/915/920 Mhz

136

* IP66 Waterproof Enclosure

137

* Ultra-Low Power consumption

138

* AT Commands to change parameters

139

* 4000mAh or 8500mAh Battery for long term use。

140

141

== 1.4 Applications ==

142

143

* Smart Buildings & Home Automation

144

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

(% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)(%%)

== 1.5 Pin Definitions and Switch ==

155

156

(% class="wikigeneratedid" %)

157

[[image:1656295519542-152.png||height="413" width="728"]]

158

159

160

(% class="wikigeneratedid" %)

161

[[image:1656295532863-613.png||height="371" width="721"]]

162

163

164

(% class="wikigeneratedid" %)

165

[[image:image-20220627101527-1.png]]

166

167

(% class="wikigeneratedid" style="display:none" %)

=== 1.5.1 Jumper JP2 ===

172

173

Power on Device when put this jumper.

174

175

176

=== 1.5.2 BOOT MODE / SW1 ===

177

178

(((

179

~1. ISP: upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. Firmware won't run.

)))

(((

2. Flash: work mode, device starts to work and send out console output for further debug

)))

=== 1.5.3 Reset Button ===

188

189

Press to reboot the device.

=== 1.5.4 LED ===

It will flash:

1. When boot the device in flash mode

197

1. Send an uplink packet

198

199

=== 1.6 Hardware Change log ===

200

201

Note: Hardware version is marked in the PCB.

**LSN50 v2.1:**

1. Change R14 to 1M ohm

206

1. Change R3, R4 to 4.7Kohm. So no need to modify them for 3 DS18B20 connection.

207

1. Add ESD to each I/O

**LSN50 v2.0:**

* Change to a new enclosure. Improve with external antenna, IP68, ear hook.

**LSN50 v1.3**:

* Add P-MOS to control 5V output

**LSN50 v1.2**:

* Add LED. Turn on for every LoRa transmit

220

* Add pin PA4, PB13, NRST

221

* Add 5V Output, on/off control by PB5(Low to Enable, High to Disable)

222

223

== (% id="cke_bm_478801S" style="display:none" %) (%%)1.7 Hole Option ==

224

225

The LSN50 provides different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

226

227

[[image:image-20220627104757-1.png]]

228

229

230

[[image:1656298089706-973.png]]

= 2. Use LSN50 with LoRaWAN firmware =

235

236

== 2.1 How it works ==

(((

(((

The LSN50 is pre-loaded with a firmware and is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you just need to input the OTAA keys in the LoRaWAN IoT server and power on the LSN50. It will automatically join the network via OTAA.

)))

(((

)))

(((

The diagram below shows the working flow in default firmware (ver 1.7.0):

)))

[[image:image-20220627104855-2.png]]

253

254

255

In case you can't set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands>>doc:Main.End Device AT Commands and Downlink Command.WebHome]] to set the keys in the LSN50.

)))

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

260

261

(((

262

Following is an example for how to join the [[TTN V3 LoRaWAN Network>>url:http://www.thethingsnetwork.org/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.

263

264

(% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:1655891470063-521.png]](% title="Click and drag to resize" %)[[image:1656298385089-555.png]]

)))

(% title="Click and drag to resize" %)(%%)The LG308 is already set to connected to [[TTN V3 network >>url:https://www.thethingsnetwork.org/]], so what we need to now is configure the TTN V3 server.(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)(%%)

(((

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LSN50.

275

276

Each LSN50is shipped with a sticker with the default device EUI as below:

)))

(((

)))

(% aria-label="image-20220607170145-1.jpeg image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20220607170145-1.jpeg||data-widget="image"]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)(%%)

(((

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

288

289

**Register the device：**

290

)))

291

292

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)(% aria-label="1654935135620-998.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1654935135620-998.png||data-widget="image"]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](%%)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)

293

294

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)

295

296

297

**Add APP EUI and DEV EUI：**

298

299

300

(% aria-label="image-20220611161308-4.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20220611161308-4.png||data-widget="image" height="551" width="753"]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

**Add APP EUI in the application：**

305

306

307

(% aria-label="image-20220611161308-5.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20220611161308-5.png||data-widget="image" height="601" width="742"]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

**Add APP KEY**

(% aria-label="image-20220611161308-6.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20220611161308-6.png||data-widget="image" height="485" width="744"]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

313

314

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)

315

316

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)(%%)

317

318

(% style="color:blue" %)**Step 2**(%%): Power on LSN50

319

320

Put a Jumper on JP2 to power on the device.(% style="display:none" %)

321

322

[[image:image-20220627145643-5.png]](% style="display:none" %)

323

324

(% style="display:none" %)

325

326

327

(% style="display:none" %) (%%)

**For LSn50v2:**

[[image:1656313034748-905.png]](% style="display:none" %)

332

333

334

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(%%)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)(%%)

(((

(((

(% style="color:blue" %)**Step 3**(%%)**:** The LSN50 will auto join to the TTN V3 network. After join success, it will start to upload messages to TTN V3 and you can see the messages in the panel.

)))

)))

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)[[image:1656312908855-552.png]](% style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]]

343

344

(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)(% title="Click and drag to resize" %)

345

346

347

== 2.3 Working Mode & Uplink Payload ==

348

349

LSN50 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set LSN50 to different working modes.

For example:

(% style="color:red" %)**AT+MOD=2**(%%) ~/~/ will set the LSN50 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

354

355

356

(% style="color:red" %)**NOTE:**

357

358

(% style="color:red" %)1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands’ definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while LSn50 transmit in DR0 with 12 bytes payload.

359

2. All modes share the same Payload Explanation from HERE.

360

3. By default, the device will send an uplink message every 5 minutes.

361

362

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:400px" %)

363

|=(% style="width: 62.5px;" %)(((

364

**Size (bytes)**

365

366

|(% style="width:65px" %)**Value**|(((

367

[[Battery>>||anchor="HBattery:"]]

368

)))|(% style="width:61px" %)(((

369

ignore

370

)))|(% style="width:91px" %)(((

371

[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]

372

)))|(% style="width:99px" %)(((

373

[[Temperature>>||anchor="HTemperature:"]]

374

)))|(% style="width:97px" %)(((

375

[[Humidity>>||anchor="HHumidity:"]]

376

)))

377

378

=== 2.3.1 MOD~=1 (Default Mode) ===

379

380

(((

381

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

382

[[image:image-20220627171207-27.png]]

383

384

[[image:image-20220627150949-6.png]]

)))

=== 2.3.2 MOD~=2 (Distance Mode) ===

391

392

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

393

394

[[image:image-20220627180835-31.png]]

395

396

397

[[image:1656324539647-568.png]]

Connection of LIDAR-Lite V3HP:

402

403

[[image:1656324581381-162.png]]

404

405

406

Connection to Ultrasonic Sensor:

407

408

[[image:1656324598488-204.png]]

409

410

411

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

412

413

[[image:image-20220628083801-1.png]]

414

415

[[image:1656376779088-686.png]]

416

417

418

Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):

419

420

Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0

421

422

[[image:1656376795715-436.png]]

Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):

427

428

Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0

429

430

[[image:1656376865561-355.png]]

(((

Please use firmware version > 1.6.5 when use MOD=2, in this firmware version, user can use LSn50 v1 to power the ultrasonic sensor directly and with low power consumption.

)))

=== 2.3.3 MOD~=3 (3 ADC + I2C) ===

440

441

442

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

443

444

[[image:image-20220628085009-2.png]]

445

446

[[image:1656377431497-975.png]]

=== 2.3.4 MOD~=4 (3 x DS18B20) ===

451

452

453

This mode is supported in firmware version since v1.6.1. Software set to AT+MOD=4

454

455

Hardware connection is as below,

456

457

(% style="color:red" %)**(Note:**

458

459

* In hardware version v1.x and v2.0 , R3 & R4 should change from 10k to 4.7k ohm to support the other 2 x DS18B20 probes.

460

* In hardware version v2.1 no need to change R3 , R4, by default, they are 4.7k ohm already.

461

462

See [[here>>path:#hardware_changelog]] for hardware changelog.

463

464

(% style="color:red" %)**) **

465

466

[[image:1656377461619-156.png]]

467

468

469

This mode has total 11 bytes. As shown below:

470

471

[[image:image-20220628085248-3.png]]

472

473

[[image:1656377606181-607.png]]

474

475

476

=== 2.3.5 MOD~=5(Weight Measurement by HX711) ===

477

478

479

This mode is supported in firmware version since v1.6.2. Please use v1.6.5 firmware version so user no need to use extra LDO for connection.

480

481

[[image:1656378224664-860.png]]

482

483

484

Each HX711 need to be calibrated before used. User need to do below two steps:

485

486

1. Zero calibration. Don’t put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

487

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

For example:

**AT+WEIGAP =403.0**

Response: Weight is 401 g

495

496

497

Check the response of this command and adjust the value to match the real value for thing.

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:726px" %)

502

503

|(% style="width:97px" %)**Value**|(% style="width:44px" %)[[BAT>>path:#BAT]]|(% style="width:172px" %)(((

504

[[Temperature(DS18B20)>>path:#DS18B20]]

505

)))|(% style="width:51px" %)[[ADC>>path:#ADC]]|(% style="width:206px" %)[[Digital in & Digital Interrupt>>path:#Digtial_input]]|(% style="width:72px" %)Weight|(% style="width:81px" %)Reserved

506

507

[[image:1656378323863-824.png]]

=== 2.3.6 MOD~=6(Counting Mode, Since firmware v1.6.5) ===

(((

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

)))

(((

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

)))

[[image:1656378351863-572.png]]

525

526

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the LSN50 to avoid this happen.

527

528

529

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:522px" %)

530

531

|(% style="width:98px" %)**Value**|(% style="width:45px" %)[[BAT>>path:#BAT]]|(% style="width:177px" %)(((

532

[[Temperature(DS18B20)>>path:#DS18B20]]

533

)))|(% style="width:52px" %)[[ADC>>path:#ADC]]|(% style="width:85px" %)[[Digital in>>path:#Digtial_input]]|(% style="width:62px" %)Count

534

535

[[image:1656378441509-171.png]]

=== 2.3.7 Decode payload in The Things Network ===

540

541

While using TTN V3 network, you can add the payload format to decode the payload.

542

543

544

[[image:1656378466788-734.png]]

545

546

547

The payload decoder function for TTN V3 are here:

548

549

LSN50 TTN V3 Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/downloads/LSN50-LoRaST/Payload_decoder/>>url:http://www.dragino.com/downloads/downloads/LSN50-LoRaST/Payload_decoder/]]

550

551

552

(% style="display:none" %) (%%)

553

554

== 2.4 Payload Explanation and Sensor Interface ==

555

556

=== 2.4.1 Battery Info ===

557

558

Check the battery voltage for LSN50.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.4.2 Temperature (DS18B20) ===

567

568

If there is a DS18B20 connected to PB3 pin. The temperature will be uploaded in the payload.

569

570

571

More DS18B20 can check the [[3 DS18B20 mode>>path:#ds18b20_3]]

**Connection**

[[image:1656378573379-646.png]]

**Example**:

If payload is: 0105H: (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree

582

583

If payload is: FF3FH : (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

=== 2.4.3 Digital Input ===

588

589

The digital input for pin PA12,

590

591

* When PA12 is high, the bit 1 of payload byte 6 is 1.

592

* When PA12 is low, the bit 1 of payload byte 6 is 0.

593

594

595

=== 2.4.4 Analogue Digital Converter (ADC) ===

596

597

The ADC pins in LSN50 can measure range from 0~~3.3v, it use reference voltage from STM32. If user need to measure a voltage >3.3v, please use resistors to divide this voltage to lower than 3.3v, otherwise, it may destroy the ADC pin.

598

599

600

The ADC monitors the voltage on the PA0 line, in mV.

Ex: 0x021F = 543mv,

**Example1:** Reading an Oil Sensor (Read a resistance value):

606

607

[[image:image-20220627172409-28.png]]

608

609

610

In the LSN50, we can use PB4 and PA0 pin to calculate the resistance for the oil sensor.

611

612

613

(% style="color:blue" %)**Steps:**

614

615

1. Solder a 10K resistor between PA0 and VCC.

616

1. Screw oil sensor's two pins to PA0 and PB4.

617

618

The equipment circuit is as below:

619

620

[[image:image-20220627172500-29.png]]

621

622

623

According to above diagram:

624

625

[[image:image-20220628091043-4.png]]

So

[[image:image-20220628091344-6.png]]

630

631

632

[[image:image-20220628091621-8.png]] is the reading of ADC. So if ADC=0x05DC=0.9 v and VCC (BAT) is 2.9v

633

634

635

The [[image:image-20220628091702-9.png]] 4.5K ohm

636

637

Since the Bouy is linear resistance from 10 ~~ 70cm.

638

639

640

The position of Bouy is [[image:image-20220628091824-10.png]] , from the bottom of Bouy.

=== 2.4.5 Digital Interrupt ===

645

646

Digital Interrupt refers to pin PB14, and there are different trigger methods. When there is a trigger, the LSN50 will send a packet to the server.

(((

Interrupt connection method:

651

)))

652

653

[[image:1656379178634-321.png]]

654

655

656

**Example to use with door sensor **

657

(Requires firmware > 1.5.1)

658

659

660

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

661

662

[[image:1656379210849-860.png]]

663

664

665

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use LSN50 interrupt interface to detect the status for the door or window.

666

667

668

Below is the installation example:

669

670

Fix one piece of the magnetic sensor to the door and connect the two pins to LSN50 as follows:

671

672

* One pin to LSN50's PB14 pin

673

* The other pin to LSN50's VCC pin

674

675

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PB14 will be at the VCC voltage.

676

677

678

Door sensors have two types: ** (% style="color:#4472c4" %)NC (Normal close)(%%)** and (% style="color:#4472c4" %)**NO (normal open)**(%%). The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

679

680

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v2/1Mohm = 0.3uA which can be ignored.

681

682

683

[[image:1656379283019-229.png]]

(((

The above photos shows the two parts of the magnetic switch fitted to a door.

)))

(((

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

)))

The command is:

(% style="color:blue" %)**AT+INTMOD=1 **(%%)** ~/~/(more info about INMOD please refer **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. )**

699

700

701

Below shows some screen captures in TTN V3:

702

703

704

[[image:1656379339508-835.png]]

705

706

707

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

708

709

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

710

711

712

(% style="color:red" %)**Notice for hardware version LSN50 v1 < v1.3**(%%) (produced before 2018-Nov).

713

714

In this hardware version, there is no R14 resistance solder. When use the latest firmware, it should set AT+INTMOD=0 to close the interrupt. If user need to use Interrupt in this hardware version, user need to solder R14 with 10M resistor and C1 (0.1uF) on board.

715

716

[[image:1656379563303-771.png]]

=== 2.4.6 I2C Interface (SHT20) ===

721

722

The PB6(SDA) and PB7(SCK) are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

723

724

We have made an example to show how to use the I2C interface to connect to the SHT20 Temperature and Humidity Sensor. This is supported in the stock firmware since v1.5 with (% style="color:#4472c4" %)**AT+MOD=1 (default value).**

725

726

Below is the connection to SHT20.

727

728

729

[[image:1656379593307-549.png]]

730

731

732

The device will be able to get the I2C sensor data now and upload to IoT Server.

733

734

735

[[image:1656379664142-345.png]]

736

737

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

743

744

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

745

746

747

If you want to use other I2C device, please refer the SHT20 part source code as reference.

=== 2.4.7 Distance Reading ===

752

753

Refer [[Ultrasonic Sensor section>>path:#Ultrasonic_Sensor]].

754

755

756

=== 2.4.8 Ultrasonic Sensor ===

757

758

(((

759

The LSN50 v1.5 firmware supports ultrasonic sensor (with AT+MOD=2) such as SEN0208 from DF-Robot. This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

)))

(((

The LSN50 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

)))

(((

The picture below shows the connection:

770

)))

771

772

[[image:1656380061365-178.png]]

Connect to the LSN50 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

777

778

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read:0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

784

785

786

[[image:1656384895430-327.png]]

787

788

789

[[image:1656384913616-455.png]]

790

791

792

You can see the serial output in ULT mode as below:

793

794

[[image:1656384939855-223.png]]

In TTN V3 server:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

801

802

803

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]

804

805

806

=== 2.4.9 +5V Output ===

807

808

Since v1.2 hardware version, a +5v output is added in the hardware. The +5V output will be valid for every sampling. LSN50 will enable +5V output before all sampling and disable the +5v after all sampling.

809

810

811

Since firmware **v1.6.3**, The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

816

817

818

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

=== 2.4.10 Weigh Sensor HX711 ===

824

825

Since v1.6.2 firmware, LSN50 support Weigh Sensor HX711.

826

827

828

=== 2.4.11 BH1750 Illumination Sensor ===

829

830

Since v1.7.0 firmware, MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

831

832

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.jpg]]

833

834

835

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

=== 2.4.12 Working MOD ===

840

841

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

842

843

844

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

845

846

847

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4:MOD5

* 5:MOD6

== 2.5 Configure LSN50 via AT or Downlink ==

857

858

User can configure LSN50 via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

859

860

There are two kinds of Commands:

861

862

* (% style="color:#4472c4" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.7.0, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

863

864

* (% style="color:#4472c4" %)**Sensor Related Commands**(%%): These commands are special designed for LSN50. User can see these commands below:

865

866

=== 2.5.1 Common Commands: ===

867

868

869

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.7.0, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

870

871

872

=== 2.5.2 Sensor related commands: ===

873

874

875

(% style="color:#4472c4" %)**Set work mode:**

876

877

* (% style="color:#037691" %)AT Command:

878

879

AT+MOD=2 ~/~/ Set work MOD =2. (1:IIC mode,2:Distance mode,3:3ADC mode, 4:3DS18B20 mode,5:weight mode)

880

881

AT+MOD=? ~/~/ Get current work MOD

882

883

884

* (% style="color:#037691" %)Downlink Payload:

885

886

0x0A aa ~/~/ Same as AT+MOD=aa

(% style="color:#4472c4" %)**Set the trigger interrupt mode:**

891

892

* (% style="color:#037691" %)AT Command:

893

894

AT+INTMOD=2 ~/~/ Set INTMOD =2. (0:Disable,1:falling or rising,2:falling,3:rising)

895

896

AT+INTMOD=? ~/~/ Get current INTMOD

897

898

899

* (% style="color:#037691" %)Downlink Payload:

900

901

0x06 000003 ~/~/ Set AT+INTMOD=3

902

903

904

(% style="color:#4472c4" %)**Set the 5V power open time during sampling:**

905

906

907

* (% style="color:#037691" %)AT Command:

908

909

AT+5VT=1000 ~/~/ Set 5v open time to 1000ms

910

911

AT+5VT=? ~/~/ Check current 5v open duration

912

913

914

* (% style="color:#037691" %)Downlink Payload:

915

916

0x07 aa bb ~/~/ Equal AT+5VT=0x(aa bb)

(% style="color:#4472c4" %)**Set the weight to 0g (Zero Calibration)**

922

923

* (% style="color:#037691" %)AT Command:

924

925

AT+WEIGRE ~/~/ Set the weight to 0g

926

927

928

* (% style="color:#037691" %)Downlink Payload:

929

930

0x08 01 ~/~/ Set the weight to 0g

(% style="color:#4472c4" %)**Get or Set the GAP Value (calibrate factor) of measurement**

935

936

* (% style="color:#037691" %)AT Command:

937

938

AT+WEIGAP=403.0 ~/~/ Set GAP Value =403.0 (response: Weight: xx g)

939

940

AT+WEIGAP=? ~/~/ Get current GAP Value

941

942

943

* (% style="color:#037691" %)Downlink Payload:

944

945

0x08 02 aa bb ~/~/ Equal to AT+WEIGAP=0x(aa bb)/10

== 2.6 Show Data in Datacake IoT Server ==

954

955

Datacake provides a human friendly interface to show the sensor data, once we have data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

956

957

958

(% style="color:blue" %)Step 1(%%): Be sure that your device is programmed and properly connected to the network at this time.

959

960

(% style="color:blue" %)Step 2(%%): To configure the Application to forward data to Datacake you will need to add integration. To add the Datacake integration, perform the following steps:

961

962

963

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]

964

965

966

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

967

968

969

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]

(% style="color:blue" %)Step 3(%%): Create an account or log in Datacake.

974

975

(% style="color:blue" %)Step 4(%%): Search the LSN50 and add DevEUI.

976

977

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]

== 2.7 Firmware Change Log ==

982

983

~* [[**Firmware download link**>>url:https://github.com/dragino/LoRa_STM32/tree/master/LSN50.hex]]

984

985

[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Firmware/LSN50.hex/>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Firmware/LSN50.hex/]]

986

987

988

**~* Firmware Change Log:**

989

990

[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Firmware/LSN50.hex/>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Firmware/LSN50.hex/]]

== 2.8 Use VDD or +5V to Power External Sensor ==

996

997

User can use VDD or +5V to power external sensor.

998

999

(% style="color:red" %)Note:

1000

1001

1. VDD is 2.5~~3.3v from the battery + diode, the VDD is always on, so when use VDD to power external sensor, make sure the sensor has a low power consumption in sleep mode ( less 50 uA) to get a long battery life.

1002

1. +5V output is only ON when sampling. And MCU will turn off it after sampling. So if sensor can support 5v, +5V out is the best choice. [[See here for more info>>path:#output_5v]].

1003

1004

(% style="color:red" %)Note: Always test the actually current pass by the JP2 jumper when connect to a new type of sensor.

== 2.9 Battery Analysis ==

1013

1014

=== 2.9.1 Battery Type ===

1015

1016

The LSN50 battery is a combination of a 4000mAh or 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.

1017

1018

1019

The battery is designed to last for more than 5 years for the LSN50.

1020

1021

1022

The battery related documents as below:

1023

1024

* [[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],

1025

* [[Lithium-Thionyl Chloride Battery datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]

1026

* [[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]

1027

1028

[[image:image-20220627175349-30.png]]

1029

1030

1031

=== 2.9.2 Power consumption Analyze ===

1032

1033

When connect to different sensors, it is good to test the power consumption with the sensor working. User can remove the [[ON/OFF Jumper>>path:#power_on]] of LSN50, and connect a multimeter between the two pins of this header and measure the current to know the whole system power consumption. Because the sleep mode will have as low as 10uA, at least 4.5 digit multimeter is required to measure this level of current.

1034

1035

A victor VC86E is recommended.

1036

1037

[[image:1656323400306-359.png]]

1038

1039

1040

In a minimum system with DS18B20 and Oil Sensor and default firmware, the power consumption includes:

1041

1042

1043

~1. Deep Sleep (Stop mode) for STM32. ~~ 5uA

1044

1045

2. Sampling current while reading DS18B20 and Oil Sensor

1046

1047

* Oil Sensor sampling time: 200us, current: 0.3mA

1048

* DS18B20 sampling time: 750ms, current: 0.64mA

1049

* Above power should add 8mA CPU power in working mode.

1050

1051

3. LoRaWAN transmit and receive time consumption. The LoRa TX / RX time and power can be found in the [[LoRa calculator tool>>url:https://www.semtech.com/uploads/documents/SX1272LoRaCalculatorSetup1_1.zip]].

1052

1053

1054

In a typical LoRaWAN data transmit. The energy profile is as below:

1055

1056

1057

[[image:1656323450362-299.png]]

1058

1059

In the LoRaWAN protocol, the device will transfer in different LoRa Radio, and have different energy profile in LoRa part. We can calculate the battery life in two cases:

1060

1061

1. Lower power LoRa radio. Device has a good signal to gateway

1062

1. Higher power LoRa radio. Device has a poor signal to gateway

1063

1064

(% style="color:blue" %)**Low Power Case**:

1065

1066

* Radio Parameter: SF7, 125kHz, 20dbm

1067

* Transmit interval: 15 minutes.

1068

* Payload: 8 Bytes.

1069

1070

(% style="color:blue" %)**High Power Case**:

1071

1072

* Radio Parameter: SF10, 125kHz, 20dbm

1073

* Transmit interval: 15 minutes.

1074

* Payload: 8 Bytes.

1075

1076

To simplify the calculation, we can:

1077

1078

* Combine oil sensor and DS18B20 sampling energy together to **751ms@8.64ma**

1079

1080

* Combine the two RX windows together.

1081

1082

There is a [[power consumption tool>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=Battery_Calculator_v1.0.xlsx]] for easy analysis. Below is the analysis result.

1083

1084

1085

[[image:1656323531520-949.png]]

1086

1087

[[image:1656323549994-233.png]]

1088

1089

1090

(% style="color:red" %)Note: Ignore the 18 year result, because the battery has a max 2% discharge per year.

1091

1092

1093

=== 2.9.3 Battery Note ===

1094

1095

(((

1096

The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.

)))

=== 2.9.4 Replace the battery ===

1101

1102

(((

1103

You can change the battery in the LSN50.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.

)))

(((

The default battery pack of LSN50 includes a ER18505 plus super capacitor. If user can't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).

)))

= 3. Using the AT Commands =

1113

1114

== 3.1 Access AT Commands ==

1115

1116

LSN50 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSN50 for using AT command, as below.

1117

1118

1119

(% style="color:#4472c4" %)**LSN50 v1 UART connection photo**

1120

1121

[[image:image-20220627165424-24.png||height="495" width="486"]]

1122

1123

1124

(% style="color:#4472c4" %)**LSN50 v2 UART connection photo**

1125

1126

[[image:image-20220627165424-25.png||height="483" width="988"]]

(((

In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSN50. LSN50 will output system info once power on as below:

1131

)))

1132

1133

[[image:image-20220627165531-26.png]]

== 3.2 Common AT Command Sequence ==

1138

1139

1140

=== 3.2.1 Multi-channel ABP mode (Use with SX1301/LG308) ===

1141

1142

(% style="color:#037691" %)**If device has not joined network via OTAA:**

1143

1144

(% style="background-color:#dcdcdc" %)AT+FDR

1145

1146

(% style="background-color:#dcdcdc" %)AT+NJM=0

1147

1148

(% style="background-color:#dcdcdc" %)ATZ

1149

1150

1151

(% style="color:#037691" %)**If device already joined network:**

1152

1153

(% style="background-color:#dcdcdc" %)AT+NJM=0

1154

1155

(% style="background-color:#dcdcdc" %)ATZ

1156

1157

1158

=== 3.2.2 Single-channel ABP mode (Use with LG01/LG02) ===

1159

1160

See [[Sect 6.7>>path:#single_channel_mode]]

= 4. Upload Firmware =

1165

1166

(% style="color:red" %)**Notes**:

1167

1168

* Since image v1.3, the firmware will show version info during boot. If your device doesn't show version info, you may have a very old image version.

1169

* Always run AT+FDR to reset parameters to factory default after an update image.

1170

If the update is from image >= v1.3 to another image version >=v1.3, then the keys will be kept after running AT+FDR.

1171

Otherwise (e.g. from v1.2 to v1.3), AT+FDR may erase the keys.

1172

1173

== 4.1 Upload Firmware via Serial Port ==

1174

1175

The LSN50's AT Command port can be used for firmware upgrade. The hardware connection for upgrade firmware is as below:

1176

1177

1178

[[image:image-20220627163506-18.png||height="426" width="418"]]

1179

1180

1181

(% style="color:blue" %)**Step1**(%%)**:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1182

1183

1184

(% style="color:blue" %)**Step2**(%%)**:** Download the [[LSN50 Image files>>url:https://github.com/dragino/LoRa_STM32/tree/master/LSN50.hex]].

1185

1186

1187

(% style="color:blue" %)**Step3**(%%)**: **Open flashloader; choose the correct COM port to update

1188

1189

[[image:image-20220627163821-19.png]]

1190

1191

1192

[[image:image-20220627163930-20.png||height="450" width="751"]]

1193

1194

1195

[[image:image-20220627164030-21.png||height="459" width="750"]]

1196

1197

(% style="color:blue" %)**Step4**(%%)**: **Switch SW1 back to flash state and push the RESET button.

1198

1199

The LSN50 will then run the new firmware.

1200

1201

1202

== 4.2 Upload Firmware via ST-Link V2 ==

1203

1204

You can use ST-LINK to upgrade firmware into LSN50. The hardware connection for upgrade firmware is as below:

1205

1206

[[image:1656319349131-664.png]]

Connection:

* ST-LINK v2 GND <~-~-> LSN50 GND

1211

* ST-LINK v2 SWCLK <~-~-> LSN50 PA14

1212

* ST-LINK v2 SWDIO <~-~-> LSN50 PA13

1213

* ST-LINK v2 RST <~-~->LSN50 NRST.

1214

1215

(% style="color:blue" %)**Step1:**(%%) Install [[ST-LINK driver>>url:https://www.stmicroelectronics.com.cn/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-utilities/stsw-link009.html]] first and then install [[ST-LINK Utility>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stsw-link004.html]]

1216

1217

1218

(% style="color:blue" %)**Step2**(%%): Download the [[LSN50 Image files>>url:https://github.com/dragino/LoRa_STM32/tree/master/LSN50.hex]].

1219

1220

1221

(% style="color:blue" %)**Step3:**(%%)** **Open ST-LINK utility, (% style="color:blue" %)**file ~-~-> open file**(%%) to select the image to be upgraded.

1222

1223

1224

(% style="color:blue" %)**Step4:**(%%)** **Click the “(% style="color:blue" %)**Program Verify**”(%%) button on ST-LINK.

1225

1226

1227

[[image:image-20220627164303-22.png]]

1228

1229

1230

(% style="color:blue" %)**Step5:**(%%)** **The led on the ST-LINK adapter will now blinking, and the ST-Link utility will pop up a download window. Click the start button to download the image to LSN50.

1231

1232

1233

(% style="color:red" %)NOTE: If this step fails, ST-LINK can't establish connection to LSN50, please try to swap SWDIO & SWCLK pin. Some ST-LINK v2 devices are incorrectly marked.

1234

1235

1236

[[image:image-20220627164303-23.png]]

= 5. Developer Guide =

1241

1242

(% style="display:none" %)

1243

1244

* Software Source Code Download : [[https:~~/~~/github.com/dragino/LoRa_STM32/tree/master/STM32CubeExpansion_LRWAN>>https://github.com/dragino/LoRa_STM32/tree/master/STM32CubeExpansion_LRWAN]]

1245

* Hardware Source Code Download: [[https:~~/~~/github.com/dragino/Lora/tree/master/LSN50>>https://github.com/dragino/Lora/tree/master/LSN50]]

1246

1247

LSN50 is an open source project, developer can use compile their firmware for customized applications. User can get the source code from:

1248

1249

* Software Source Code: [[https:~~/~~/github.com/dragino/LoRa_STM32/tree/master/STM32CubeExpansion_LRWAN>>url:https://github.com/dragino/LoRa_STM32/tree/master/STM32CubeExpansion_LRWAN]]

1250

* Hardware Design files: [[https:~~/~~/github.com/dragino/Lora/tree/master/LSN50>>url:https://github.com/dragino/Lora/tree/master/LSN50]]

1251

* Compile instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Compile%20Instruction%20~~-~~-%20STM32/>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Compile%20Instruction%20--%20STM32/]]

1252

1253

Use Keil to open project file:

1254

1255

STM32CubeExpansion_LRWAN/Projects/Multi/Applications/LoRa/DRAGINO-LRWAN(AT)/MDK-ARM/STM32L072CZ-Nucleo/Lora.uvprojx

1256

1257

1258

In Keil, you can see what frequency band the code support.

1259

1260

[[image:image-20220627162417-15.png]]

1261

1262

1263

~1. If you want to change frequency, modify the Preprocessor Symbols.

1264

For example, change EU868 to US915

1265

1266

[[image:1656318662202-530.png]]

1267

1268

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.emz]]

2. Compile and build

[[image:image-20220627163212-17.png]]

= 6. FAQ =

== 6.1 Why there is 433/868/915 version? ==

1279

1280

(((

1281

Different countries have different rules for the ISM band for LoRa. Although the LoRa chip can support a wide range of Frequencies, we provide different versions of the hardware for best tune of the LoRa hardware part.

)))

== 6.2 What is the frequency range of LT LoRa part? ? ==

1286

1287

Different LT version supports different frequency range, below is the table for the working frequency and recommend bands for each model:

1288

1289

[[image:image-20220627155456-9.png]]

== 6.3 How to change the LoRa Frequency Bands/Region? ==

1294

1295

You can follow the instructions for [[how to upgrade image>>path:#3ygebqi]].

1296

When downloading the images, choose the required image file for download.

1297

1298

1299

== 6.4 Can I use Private LoRa protocol? ==

(((

(((

The stock firmware is based on LoRaWAN protocol. You can use a private LoRa protocol in LSN50. This section describes an example for base LoRa transfer. It is a reference/demo and we do not provide further software development support on this topic.

)))

(((

In this demo, we will show the communication between LoRa Shield and LSN50, both of them using the basic LoRa library. LSN50 will send a message to a LoRa Shield and the LoRa Shield will print it to the console.

)))

)))

(% style="color:#4472c4" %)**LoRa Shield + UNO**:

1314

1315

Use the [[LoRa Library>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/LoRa_Raw_Example/Arduino/&file=LoRa.zip]] and upload the [[LoRa Receive>>http://www.dragino.com/downloads/downloads/LSN50-LoRaST/LoRa_Raw_Example/Arduino/LoRaReceiver.ino]] Sketch to Arduino.

Refs:

[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/LoRa_Raw_Example/Arduino/&file=LoRa.zip>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/LoRa_Raw_Example/Arduino/&file=LoRa.zip]]

1321

1322

[[http:~~/~~/www.dragino.com/downloads/downloads/LSN50-LoRaST/LoRa_Raw_Example/Arduino/LoRaReceiver.ino>>url:http://www.dragino.com/downloads/downloads/LSN50-LoRaST/LoRa_Raw_Example/Arduino/LoRaReceiver.ino]]

1323

1324

1325

Open the serial monitor to Arduino. The device acts as a LoRa Receiver and listen on the frequency 868.3Mhz by default.

1326

1327

1328

(% style="color:#4472c4" %)**LSN50**:

1329

1330

Use the <[[LoRa RAW code>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/LoRa_Raw_Example/LSN50/&file=lora_send.zip]]> . The project file is in: MDK-ARM\STM32L072CZ-Nucleo\ Lora.uvprojx

1331

1332

[[Compile>>path:#19c6y18]] it and [[Upload>>path:#3ygebqi]] it to LSN50, the LSN50 will transfer on the frequency 868.3Mhz.

1333

1334

In the Arduino Console, it will see the received packets as below.

1335

1336

1337

[[image:image-20220627160116-10.png]]

1338

1339

1340

== 6.5 How to set up LSN50 to work in 8 channel mode ==

1341

1342

By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.

1343

1344

You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.

1345

1346

1347

For example, in (% style="color:blue" %)**US915**(%%) band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.

1348

1349

[[image:image-20220627160940-13.png]]

1350

1351

1352

When you use the TTN V3 network, the US915 frequency bands use are:

1353

1354

* 903.9 - SF7BW125 to SF10BW125

1355

* 904.1 - SF7BW125 to SF10BW125

1356

* 904.3 - SF7BW125 to SF10BW125

1357

* 904.5 - SF7BW125 to SF10BW125

1358

* 904.7 - SF7BW125 to SF10BW125

1359

* 904.9 - SF7BW125 to SF10BW125

1360

* 905.1 - SF7BW125 to SF10BW125

1361

* 905.3 - SF7BW125 to SF10BW125

1362

* 904.6 - SF8BW500

1363

1364

Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN V3 network and uplink data. To solve this issue, you can access the device via the AT commands and run:

1365

1366

(% style="color:blue" %)**AT+CHE=2**

1367

1368

(% style="color:blue" %)**ATZ**

1369

1370

1371

to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.

1372

1373

The (% style="color:blue" %)**AU915**(%%) band is similar. Below are the AU915 Uplink Channels.

1374

1375

[[image:image-20220627161124-14.png]]

1376

1377

1378

== 6.6 How to set up LSN50 to work with Single Channel Gateway such as LG01/LG02? ==

1379

1380

In this case, users need to set LSN50 to work in ABP mode and transmit in only one frequency.

1381

1382

Assume we have a LG02 working in the frequency 868400000 now, below is the steps.

1383

1384

1385

(% style="color:blue" %)**Step1: **(%%)Log in TTN V3, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.

1386

1387

1388

[[image:image-20220627160542-11.png]]

1389

1390

1391

(% style="color:red" %)Note: You need to make sure the above three keys match in the device and in TTN V3. You can change them either in TTN V3 or in the Device to make them match. In TTN V3, NETSKEY and APPSKEY can be configured in the setting page, but the Device Addr is generated by TTN V3.

1392

You can also change the Device ADDR in TTN V3 by using the [[The Things Network CLI>>url:https://www.thethingsnetwork.org/docs/network/cli/quick-start.html]].

1393

1394

1395

(% style="color:blue" %)**Step2: **(%%)Run AT commands to make the LSN50 work in Single frequency and ABP mode. Below are the AT commands:

1396

1397

1398

(% style="background-color:#dcdcdc" %)AT+FDR(%%) Reset Parameters to Factory Default, Keys Reserve

1399

1400

(% style="background-color:#dcdcdc" %)AT+NJM=0(%%) Set to ABP mode

1401

1402

(% style="background-color:#dcdcdc" %)AT+ADR=0(%%) Set the Adaptive Data Rate Off

1403

1404

(% style="background-color:#dcdcdc" %)AT+DR=5(%%) Set Data Rate (Set AT+DR=3 for 915 band)

1405

1406

(% style="background-color:#dcdcdc" %)AT+TDC=300000(%%) Set transmit interval to 5 minutes

1407

1408

(% style="background-color:#dcdcdc" %)AT+CHS=868400000(%%) Set transmit frequency to 868.4Mhz

1409

1410

(% style="background-color:#dcdcdc" %)AT+DADDR=26 01 1A F1(%%) Set Device Address to 26 01 1A F1

1411

1412

(% style="background-color:#dcdcdc" %)ATZ(%%) Reset MCU

As shown below:

[[image:image-20220627160542-12.png]]

1418

1419

1420

== 6.7 How to configure the EUI keys in LSN50? ==

1421

1422

The early version of LSN50 firmware doesn't have pre-configured keys.

1423

It is recommended that you update the image to the latest version before configure the keys. Refer [[upgrade_image>>path:#3ygebqi]] to update the firmware to the latest version.

1424

1425

Run AT commands to set the keys to desired keys; refer [[AT Command manual>>path:#23ckvvd]].

1426

1427

1428

= 7. Trouble Shooting =

1429

1430

== 7.1 Connection problem when uploading firmware. ==

1431

1432

(% style="color:red" %)**Issue**(%%): While using USB to TTL to upload firmware via UART interface. It works for several times but most of times it fails.

1433

1434

1435

(% style="color:green" %)**Checklist**:

1436

1437

~1. Double check if follow up exactly the steps as manual.

1438

1439

2. Check if hardware works fine: a) check if AT command works, b) check if ISP / flash switch works: PA12 will have different output level while set the ISP/Flash Switch in different position. c) check if reset button works.

1440

1441

3. If you use Windows10 system. Please change the flash loader to run in Windows7 compatibility mode.

1442

1443

1444

[[image:image-20220627153421-8.png]]

1445

1446

4. We have seen cases where the FT232 USB TTL adapter has a reliability issue with the PC USB chipset (Intel). In this case, even though points 1 and 2 above work, it still has a reliability issue for uploading. If this happens, change to a different PC or change the USB to TTL adapter to solve the issue.

1447

1448

1449

== 7.2 Why I can't join TTN V3 in US915 / AU915 bands? ==

1450

1451

It is due to channel mapping. Please see the [[Eight Channel Mode>>path:#206ipza]] section above for details.

1452

1453

1454

7.3 AT Command input doesn't work

1455

1456

In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:red" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:red" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.

= 8. Order Info =

Part Number: (% style="color:blue" %)**LSN50-XX-YY **(%%)**or (% style="color:blue" %)LSN50-XX-YY-ZZ(%%)**

1463

1464

1465

(% style="color:blue" %)**XX**(%%): The default frequency band

1466

1467

* (% style="color:red" %)**AS923 **(%%)**:** LoRaWAN AS923 band

1468

* (% style="color:red" %)**AU915 **(%%)**:** LoRaWAN AU915 band

1469

* (% style="color:red" %)**EU433 **(%%)**:** LoRaWAN EU433 band

1470

* (% style="color:red" %)**EU868 **(%%)**:** LoRaWAN EU868 band

1471

* (% style="color:red" %)**KR920 **(%%)**:** LoRaWAN KR920 band

1472

* (% style="color:red" %)**US915 **(%%)**:** LoRaWAN US915 band

1473

* (% style="color:red" %)**IN865 **(%%)**:** LoRaWAN IN865 band

1474

* (% style="color:red" %)**CN470 **(%%)**:** LoRaWAN CN470 band

1475

1476

(% style="color:blue" %)**YY**(%%)**: **Hole Option

1477

1478

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1479

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1480

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole (LSN50 v2 doesn’t have this version)

1481

* (% style="color:red" %)**NH**(%%): No Hole

1482

1483

(% style="color:blue" %)**ZZ**(%%)**: **Battery Option ( Only valid for v2 model)

1484

1485

* (% style="color:red" %)**4**(%%): with 4000mAh battery

1486

* (% style="color:red" %)**8**(%%): with 8500mAg battery

= 9. Packing Info =

(% style="color:blue" %)**For LSN50**(%%)**:**

1492

1493

**Package Includes**:

1494

1495

* LSN50 LoRa Sensor Node x 1

1496

1497

**Dimension and weight**:

1498

1499

* Device Size: 8 x 6.5 x 5 cm

1500

* Device Weight: 137g

1501

* Package Size / pcs : 9 x 7 x 6cm

1502

* Weight / pcs : 160g

1503

1504

(% style="color:blue" %)**For LSN50 v2**(%%)**:**

1505

1506

**Package Includes**:

1507

1508

* LSN50 v2 LoRa Sensor Node x 1

1509

* External antenna x 1

1510

* Spring Antenna (evaluate purpose)

1511

1512

**Dimension and weight**:

1513

1514

* Device Size: 9.7 x 6.5 x 4.7 cm

1515

* Device Weight: 150g

1516

* Package Size / pcs : 14.0 x 8x 5 cm

1517

* Weight / pcs : 180g

(((

)))

= 10. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1530

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].

= 11. References =

* [[Product Page>>url:http://www.dragino.com/products/lora/item/128-lsn50.html]]

1535

* [[Data Sheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/EN/&file=Datasheet_LoRaSensorNode.pdf]]

1536

* [[Image Download>>url:https://github.com/dragino/LoRa_STM32/tree/master/LSN50.hex]]

1537

* [[Mechanical Drawing>>http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Mechanical_Drawing/]]

1538

1539

Wiki source code of LSN50 & LSN50-V2 - LoRaWAN Sensor Node User Manual

Applications

Navigation