LMDS200 - LoRaWAN Microwave Radar Distance Sensor User Manual

The Dragino LMDS200 is a (% style="color:#4472c4" %)**LoRaWAN Microwave Radar distance sensor**(%%). It uses (% style="color:#4472c4" %)**24Ghz Microwave**(%%) to detect the distance between sensor and different objects. Compare vs ultrasonic or Lidar measurement method, Microwave Radar is (% style="color:#4472c4" %)**more reliable for condensation / dusty environment**(%%). It can sense correct distance even there is water or thick dust on top of the sensor.

24

)))

25

(((

)))

(((

The LMDS200 can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.

)))

(((

)))

(((

LMDS200 can (% style="color:#4472c4" %)**measure two distances**(%%): the closest object and next object behind the closest one.

)))

(((

)))

(((

LMDS200 supports (% style="color:#4472c4" %)**Alarm Feature**(%%), user can set the LMDS200 to uplink data in a short interval when the distance is out of configured range.

)))

(((

)))

(((

The LoRa wireless technology used in LMDS200 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.

)))

(((

)))

(((

LMDS200 is powered by 8500mAh Li-SOCI2 battery, it is designed for long term use up to 5 years.

)))

(((

)))

(((

Each LMDS200 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.

)))

(((

)))

(((

*Battery life depends on how often to send data, please see [[battery analyzer>>||anchor="H4. Battery & how to replace"]].

)))

)))

)))

)))

)))

[[image:1655277036890-950.png]]

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

94

* Ultra-low power consumption

95

* Microwave Radar for distance detection

96

* Short uplink interval for Distance Alarm

97

* Monitor Battery Level

98

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

99

* AT Commands to change parameters

100

* Uplink on periodically

101

* Downlink to change configure

102

* 8500mAh Battery for long term use

* Wall Mountable

* Outdoor Use

== 1.3 Radar probe specification ==

109

110

* Measuring Method: FMCW

111

* Frequency: 24.000 ~~ 24.500 GHz

112

* Measurement output power: 6dBm

113

* Measure range: 0.5 ~~ 20m

114

* Accuracy: ±0.1m

115

* Resolution: 0.01m

116

* Horizontal Angel: 78°

117

* Vertical Angel: 23°

== 1.4 Mechanical ==

[[image:image-20220615090910-1.png]]

124

125

126

[[image:image-20220615090910-2.png]]

== 1.5 Install LDDS20 ==

131

132

133

(% style="color:blue" %)**Step 1**(%%): Choose the installation point.

134

135

LDDS20 (% style="color:red" %)**MUST**(%%) be installed on the container bottom middle position.

136

137

[[image:image-20220615091045-3.png]]

(((

(% style="color:blue" %)**Step 2**(%%): Polish the installation point.

)))

(((

For Metal Surface with paint, it is important to polish the surface, first use crude sand paper to polish the paint level , then use exquisite sand paper to polish the metal level to make it shine & smooth.

147

)))

148

149

[[image:image-20220615092010-11.png]]

150

151

152

No polish needed if the container is shine metal surface without paint or non-metal container.

153

154

[[image:image-20220615092044-12.png]]

(((

(% style="color:blue" %)**Step3: **(%%)Test the installation point.

)))

(((

Power on LDDS75, check if the blue LED is on, If the blue LED is on, means the sensor works. Then put ultrasonic coupling paste on the sensor and put it tightly on the installation point.

)))

(((

)))

(((

It is necessary to put the coupling paste between the sensor and the container, otherwise LDDS20 won’t detect the liquid level.

172

)))

173

174

[[image:1655256160324-178.png]][[image:image-20220615092327-13.png]]

(((

After paste the LDDS20 well, power on LDDS20. In the first 30 seconds of booting, device will check the sensors status and BLUE LED will show the status as below. After 30 seconds, BLUE LED will be off to save battery life.

)))

(((

)))

(((

(% style="color:red" %)**LED Status:**

)))

* (((

Onboard LED: When power on device, the onboard LED will fast blink 4 times which means detect the sensor well.

)))

* (((

(% style="color:blue" %)BLUE LED(% style="color:red" %) always ON(%%): Sensor is power on but doesn’t detect liquid. There is problem in installation point.

195

)))

196

* (((

197

(% style="color:blue" %)BLUE LED(% style="color:red" %) slowly blinking(%%): Sensor detects Liquid Level, The installation point is good.

)))

(((

LDDS20 will enter into low power mode at 30 seconds after system reset or power on, Blue LED will be off after that.

)))

(((

)))

(((

(% style="color:red" %)**Note 2:**

)))

(((

(% style="color:red" %)Ultrasonic coupling paste (%%) is subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally.

)))

(((

)))

(((

)))

(((

(% style="color:blue" %)**Step4: **(%%)Install use Epoxy ab glue.

)))

(((

Prepare Eproxy AB glue.

)))

(((

Put Eproxy AB glue in the sensor and press it hard on the container installation point.

)))

(((

Reset LDDS20 and see if the BLUE LED is slowly blinking.

238

)))

239

240

[[image:image-20220615091045-8.png||height="226" width="380"]] [[image:image-20220615091045-9.png||height="239" width="339"]]

(((

(% style="color:red" %)**Note 1:**

)))

(((

Eproxy AB glue needs 3~~ 5 minutes to stable attached. we can use other glue material to keep it in the position.

)))

(((

)))

(((

(% style="color:red" %)**Note 2:**

)))

(((

(% style="color:red" %)Eproxy AB glue(%%) is subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally.

)))

== 1.6 Applications ==

266

267

* Smart liquid control solution.

268

* Smart liquefied gas solution.

269

270

== 1.7 Precautions ==

271

272

* At room temperature, containers of different materials, such as steel, glass, iron, ceramics, non-foamed plastics and other dense materials, have different detection blind areas and detection limit heights.

273

* For containers of the same material at room temperature, the detection blind zone and detection limit height are also different for the thickness of the container.

274

* When the detected liquid level exceeds the effective detection value of the sensor, and the liquid level of the liquid to be measured shakes or tilts, the detected liquid height is unstable.

275

276

== 1.8 Pin mapping and power on ==

277

278

279

[[image:1655257026882-201.png]]

= 2. Configure LDDS20 to connect to LoRaWAN network =

284

285

286

== 2.1 How it works ==

287

288

(((

289

The LDDS20 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LDDS20. If there is coverage of the LoRaWAN network, it will automatically join the network via OTAA and start to send the sensor value.

)))

(((

In case you can't set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.A0UsingtheATCommands"]]to set the keys in the LDDS20.

)))

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

299

300

(((

301

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.

)))

(((

[[image:1655257698953-697.png]]

)))

(((

(((

The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

)))

)))

(((

(((

)))

(((

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LDDS20.

)))

)))

(((

(((

Each LDDS20 is shipped with a sticker with the default device keys, user can find this sticker in the box. it looks like below.

)))

)))

[[image:image-20220607170145-1.jpeg]]

(((

(((

For OTAA registration, we need to set **APP EUI/ APP KEY/ DEV EUI**. Some server might no need to set APP EUI.

)))

)))

(((

(((

Enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

)))

(((

(((

)))

(((

**Add APP EUI in the application**

)))

)))

[[image:image-20220610161353-4.png]]

356

357

[[image:image-20220610161353-5.png]]

358

359

[[image:image-20220610161353-6.png]]

360

361

362

[[image:image-20220610161353-7.png]]

You can also choose to create the device manually.

367

368

[[image:image-20220610161538-8.png]]

**Add APP KEY and DEV EUI**

373

374

[[image:image-20220610161538-9.png]]

(% style="color:blue" %)**Step 2**(%%): Power on LDDS20

379

380

381

Put a Jumper on JP2 to power on the device. ( The Switch must be in FLASH position).

382

383

[[image:image-20220615095102-14.png]]

(((

(% style="color:blue" %)**Step 3**(%%)**:** The LDDS20 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.

389

)))

390

391

[[image:1654849068701-275.png]]

== 2.3 Uplink Payload ==

(((

(((

(((

LDDS20 will uplink payload via LoRaWAN with below payload format:

)))

(((

Uplink payload includes in total 8 bytes.

405

Payload for firmware version v1.1.4. . Before v1.1.3, there is only 5 bytes: BAT and Distance(Please check manual v1.2.0 if you have 5 bytes payload).

)))

)))

)))

(((

)))

(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)

415

|=(% style="width: 62.5px;" %)(((

416

**Size (bytes)**

417

)))|=(% style="width: 62.5px;" %)**2**|=**2**|=1|=2|=**1**

418

|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((

419

[[Distance>>||anchor="H2.3.2A0Distance"]]

420

421

(unit: mm)

422

)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((

423

[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]

424

)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]

425

426

[[image:1654850511545-399.png]]

=== 2.3.1 Battery Info ===

431

432

433

Check the battery voltage for LDDS20.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Distance ===

442

443

(((

444

Get the distance. Flat object range 20mm - 2000mm.

)))

(((

For example, if the data you get from the register is __0x06 0x05__, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** 0605(H) = 1541 (D) = 1541 mm.**

449

)))

450

451

* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.

452

* If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid.

453

454

=== 2.3.3 Interrupt Pin ===

455

456

This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2A0SetInterruptMode"]] for the hardware and software set up.

**Example:**

0x00: Normal uplink packet.

461

462

0x01: Interrupt Uplink Packet.

=== 2.3.4 DS18B20 Temperature sensor ===

467

468

This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.

**Example**:

If payload is: 0105H: (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree

473

474

If payload is: FF3FH : (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

475

476

(% style="color:red" %)Note: DS18B20 feature is supported in the hardware version > v1.3 which made since early of 2021.

=== 2.3.5 Sensor Flag ===

481

482

(((

483

0x01: Detect Ultrasonic Sensor

)))

(((

0x00: No Ultrasonic Sensor

)))

=== 2.3.6 Decode payload in The Things Network ===

493

494

While using TTN network, you can add the payload format to decode the payload.

495

496

497

[[image:1655261164557-670.png]]

498

499

(((

500

The payload decoder function for TTN V3 is here:

)))

(((

(((

LDDS20 TTN V3 Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDDS20/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]

)))

)))

== 2.4 Downlink Payload ==

512

513

By default, LDDS20 prints the downlink payload to console port.

514

515

[[image:image-20220615100930-15.png]]

**Examples:**

* (% style="color:blue" %)**Set TDC**

522

523

If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.

524

525

Payload: 01 00 00 1E TDC=30S

526

527

Payload: 01 00 00 3C TDC=60S

528

529

530

* (% style="color:blue" %)**Reset**

531

532

If payload = 0x04FF, it will reset the LDDS20

533

534

535

* (% style="color:blue" %)**CFM**

536

537

Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0

== 2.5 Show Data in DataCake IoT Server ==

542

543

(((

544

[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:

)))

(((

)))

(((

(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**

)))

(((

(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**

)))

[[image:1654592790040-760.png]]

561

562

563

[[image:1654592800389-571.png]]

564

565

566

(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**

567

568

(% style="color:blue" %)**Step 4**(%%)**: Search the LDDS75 and add DevEUI.(% style="color:red" %)(Note: LDDS20 use same payload as LDDS75)(%%)**

569

570

[[image:1654851029373-510.png]]

571

572

573

After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake.

574

575

[[image:image-20220610165129-11.png||height="595" width="1088"]]

576

577

578

== 2.6 LED Indicator ==

579

580

The LDDS20 has an internal LED which is to show the status of different state.

581

582

583

* Blink once when device power on.

584

* The device detects the sensor and flashes 5 times.

585

* Solid ON for 5 seconds once device successful Join the network.

586

* Blink once when device transmit a packet.

587

588

== 2.7 Firmware Change Log ==

(((

**Firmware download link: **[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]

)))

(((

)))

(((

**Firmware Upgrade Method: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]**

)))

== 2.8 Battery Analysis ==

606

607

608

=== 2.8.1 Battery Type ===

609

610

(((

611

The LDDS20 battery is a combination of a 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.

)))

(((

)))

(((

The battery related documents as below:

)))

* (((

(((

[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],

)))

)))

* (((

(((

[[Lithium-Thionyl Chloride Battery datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],

)))

)))

* (((

(((

[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]

)))

)))

[[image:image-20220615111024-1.png]]

=== 2.8.2 Battery Note ===

643

644

The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to uplink data, then the battery life may be decreased.

=== 2.8.3 Replace the battery ===

(((

(((

You can change the battery in the NBSN95.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.

)))

(((

)))

(((

The default battery pack of NBSN95 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)

)))

)))

=== 2.8.4 Battery Life Analyze ===

667

668

(((

669

Dragino battery powered products are all run in Low Power mode. User can check the guideline from this link to calculate the estimate battery life:

)))

(((

[[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf]]

)))

= 3. Using the AT Commands =

(((

(((

)))

)))

== 3.1 Access AT Commands ==

687

688

LDDS20 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS20 for using AT command, as below.

689

690

691

[[image:image-20220610172924-4.png||height="483" width="988"]]

692

693

694

Or if you have below board, use below connection:

695

696

697

[[image:image-20220610172924-5.png]]

(((

In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LDDS20. LDDS20 will output system info once power on as below:

)))

[[image:image-20220610172924-6.png||height="601" width="860"]]

706

707

Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]].

708

709

710

AT+<CMD>? : Help on <CMD>

AT+<CMD> : Run <CMD>

AT+<CMD>=<value> : Set the value

715

716

AT+<CMD>=? : Get the value

717

718

719

(% style="color:#037691" %)** General Commands :**

AT : Attention

AT? : Short Help

ATZ : MCU Reset

AT+TDC : Application Data Transmission Interval

728

729

730

(% style="color:#037691" %)** Keys, IDs and EUIs management :**

731

732

AT+APPEUI : Application EUI

733

734

AT+APPKEY : Application Key

735

736

AT+APPSKEY : Application Session Key

737

738

AT+DADDR : Device Address

AT+DEUI : Device EUI

AT+NWKID : Network ID (You can enter this command change only after successful network connection)

743

744

AT+NWKSKEY : Network Session Key Joining and sending date on LoRa network

745

746

AT+CFM : Confirm Mode

747

748

AT+CFS : Confirm Status

749

750

AT+JOIN : Join LoRa? Network

751

752

AT+NJM : LoRa? Network Join Mode

753

754

AT+NJS : LoRa? Network Join Status

755

756

AT+RECV : Print Last Received Data in Raw Format

757

758

AT+RECVB : Print Last Received Data in Binary Format

759

760

AT+SEND : Send Text Data

761

762

AT+SENB : Send Hexadecimal Data

763

764

765

(% style="color:#037691" %)** LoRa Network Management :**

766

767

AT+ADR : Adaptive Rate

768

769

AT+CLASS : LoRa Class(Currently only support class A

770

771

AT+DCS : Duty Cycle Setting

772

773

AT+DR : Data Rate (Can Only be Modified after ADR=0)

774

775

AT+FCD : Frame Counter Downlink

776

777

AT+FCU : Frame Counter Uplink

778

779

AT+JN1DL : Join Accept Delay1

780

781

AT+JN2DL : Join Accept Delay2

782

783

AT+PNM : Public Network Mode

784

785

AT+RX1DL : Receive Delay1

786

787

AT+RX2DL : Receive Delay2

788

789

AT+RX2DR : Rx2 Window Data Rate

790

791

AT+RX2FQ : Rx2 Window Frequency

792

793

AT+TXP : Transmit Power

794

795

796

(% style="color:#037691" %)** Information :**

797

798

AT+RSSI : RSSI of the Last Received Packet

799

800

AT+SNR : SNR of the Last Received Packet

801

802

AT+VER : Image Version and Frequency Band

803

804

AT+FDR : Factory Data Reset

805

806

AT+PORT : Application Port

807

808

AT+CHS : Get or Set Frequency (Unit: Hz) for Single Channel Mode

809

810

AT+CHE : Get or Set eight channels mode, Only for US915, AU915, CN470

== 3.2 Set Interrupt Mode ==

815

816

Feature, Set Interrupt mode for GPIO_EXIT.

817

818

(% style="color:#037691" %)**Downlink Command: AT+INTMOD**

819

820

[[image:image-20220610174917-9.png]]

(((

(% style="color:#037691" %)**Downlink Command: 0x06**

)))

(((

Format: Command Code (0x06) followed by 3 bytes.

)))

(((

(((

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

)))

)))

* (((

Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode

839

)))

840

* (((

841

Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger

)))

(((

)))

(((

)))

= 4. FAQ =

== 4.1 What is the frequency plan for LDDS20? ==

855

856

LDDS20 use the same frequency as other Dragino products. User can see the detail from this link: [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]

== 4.2 How to change the LoRa Frequency Bands/Region ==

861

862

You can follow the instructions for [[how to upgrade image>>||anchor="H2.7A0200BFirmwareChangeLog"]].

863

When downloading the images, choose the required image file for download.

= 5. Trouble Shooting =

868

869

== 5.1 Why I can't join TTN V3 in US915 / AU915 bands? ==

870

871

It is due to channel mapping. Please see below link: [[Frequency band>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]]

872

873

874

== 5.2 AT Command input doesn't work ==

875

876

In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.

(((

)))

= 6. Order Info =

Part Number **:** (% style="color:blue" %)**LDDS20-XX**

887

888

889

(% style="color:blue" %)**XX**(%%)**: **The default frequency band

890

891

* (% style="color:red" %)**AS923 **(%%)**:** LoRaWAN AS923 band

892

* (% style="color:red" %)**AU915 **(%%)**:** LoRaWAN AU915 band

893

* (% style="color:red" %)**EU433 **(%%)**:** LoRaWAN EU433 band

894

* (% style="color:red" %)**EU868 **(%%)**:** LoRaWAN EU868 band

895

* (% style="color:red" %)**KR920 **(%%)**:** LoRaWAN KR920 band

896

* (% style="color:red" %)**US915 **(%%)**:** LoRaWAN US915 band

897

* (% style="color:red" %)**IN865 **(%%)**:** LoRaWAN IN865 band

898

* (% style="color:red" %)**CN470 **(%%)**:** LoRaWAN CN470 band

= 7. Packing Info =

(((

**Package Includes**:

)))

* (((

LDDS20 LoRaWAN Liquid Level Sensor x 1

)))

(((

(% style="color:red" %)**Note:**

)))

(((

(((

(% style="color:red" %)**Ultrasonic coupling paste**(%%) and(% style="color:red" %)** Eproxy AB glue**(%%) are subjected in most shipping way. So the default package doesn't include it and user needs to purchase locally.

)))

)))

(((

)))

(((

**Dimension and weight**:

)))

* (((

Device Size: cm

)))

* (((

Device Weight: g

)))

* (((

Package Size / pcs : cm

)))

* (((

Weight / pcs : g

)))

= 8. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

948

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].

Wiki source code of LMDS200 - LoRaWAN Microwave Radar Distance Sensor User Manual

Applications

Navigation