Wiki source code of LDDS20 - LoRaWAN Ultrasonic Liquid Level Sensor User Manual
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | (% style="text-align:center" %) | ||
| 2 | [[image:1655254599445-662.png]] | ||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 | |||
| 7 | **Table of Contents:** | ||
| 8 | |||
| 9 | |||
| 10 | |||
| 11 | |||
| 12 | |||
| 13 | |||
| 14 | |||
| 15 | |||
| 16 | = 1. Introduction = | ||
| 17 | |||
| 18 | == 1.1 What is LoRaWAN Ultrasonic liquid level Sensor == | ||
| 19 | |||
| 20 | ((( | ||
| 21 | |||
| 22 | |||
| 23 | ((( | ||
| 24 | ((( | ||
| 25 | ((( | ||
| 26 | The Dragino LDDS20 is a (% style="color:#4472c4" %)**LoRaWAN Ultrasonic liquid level sensor**(%%) for Internet of Things solution. It uses (% style="color:#4472c4" %)**none-contact method **(%%)to measure the height of liquid in a container without opening the container, and send the value via LoRaWAN network to IoT Server | ||
| 27 | ))) | ||
| 28 | |||
| 29 | ((( | ||
| 30 | |||
| 31 | ))) | ||
| 32 | |||
| 33 | ((( | ||
| 34 | The LDDS20 sensor is installed directly below the container to detect the height of the liquid level. User doesn’t need to open a hole on the container to be tested. The (% style="color:#4472c4" %)**none-contact measurement makes the measurement safety, easier and possible for some strict situation**. | ||
| 35 | ))) | ||
| 36 | |||
| 37 | ((( | ||
| 38 | |||
| 39 | ))) | ||
| 40 | |||
| 41 | ((( | ||
| 42 | LDDS20 uses ultrasonic sensing technology for distance measurement. LDDS20 is of high accuracy to measure various liquid such as: (% style="color:#4472c4" %)**toxic substances**(%%), (% style="color:#4472c4" %)**strong acids**(%%), (% style="color:#4472c4" %)**strong alkalis**(%%) and (% style="color:#4472c4" %)**various pure liquids**(%%) in high-temperature and high-pressure airtight containers. | ||
| 43 | ))) | ||
| 44 | |||
| 45 | ((( | ||
| 46 | |||
| 47 | ))) | ||
| 48 | |||
| 49 | ((( | ||
| 50 | The LoRa wireless technology used in LDDS20 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. | ||
| 51 | ))) | ||
| 52 | |||
| 53 | ((( | ||
| 54 | |||
| 55 | ))) | ||
| 56 | |||
| 57 | ((( | ||
| 58 | LDDS20 is powered by (% style="color:#4472c4" %)**8500mA Li-SOCI2 battery**(%%); It is designed for long term use up to 10 years*. | ||
| 59 | ))) | ||
| 60 | |||
| 61 | ((( | ||
| 62 | |||
| 63 | ))) | ||
| 64 | |||
| 65 | ((( | ||
| 66 | Each LDDS20 pre-loads with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect if there is network coverage, after power on. | ||
| 67 | ))) | ||
| 68 | |||
| 69 | ((( | ||
| 70 | |||
| 71 | ))) | ||
| 72 | ))) | ||
| 73 | |||
| 74 | ((( | ||
| 75 | ((( | ||
| 76 | (% style="color:#4472c4" %) * (%%)Actually lifetime depends on network coverage and uplink interval and other factors. | ||
| 77 | ))) | ||
| 78 | ))) | ||
| 79 | ))) | ||
| 80 | ))) | ||
| 81 | |||
| 82 | |||
| 83 | [[image:1655255122126-327.png]] | ||
| 84 | |||
| 85 | |||
| 86 | |||
| 87 | == 1.2 Features == | ||
| 88 | |||
| 89 | * LoRaWAN 1.0.3 Class A | ||
| 90 | * Ultra low power consumption | ||
| 91 | * Liquid Level Measurement by Ultrasonic technology | ||
| 92 | * Measure through container, No need to contact Liquid. | ||
| 93 | * Valid level range 20mm - 2000mm | ||
| 94 | * Accuracy: ±(5mm+S*0.5%) (S: Measure Value) | ||
| 95 | * Cable Length : 25cm | ||
| 96 | * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865 | ||
| 97 | * AT Commands to change parameters | ||
| 98 | * Uplink on periodically | ||
| 99 | * Downlink to change configure | ||
| 100 | * IP66 Waterproof Enclosure | ||
| 101 | * 8500mAh Battery for long term use | ||
| 102 | |||
| 103 | |||
| 104 | == 1.3 Suitable Container & Liquid == | ||
| 105 | |||
| 106 | * Solid Wall container such as: steel, iron, glass, ceramics, non-foaming plastics etc. | ||
| 107 | * Container shape is regular, and surface is smooth. | ||
| 108 | * Container Thickness: | ||
| 109 | ** Pure metal material. 2~~8mm, best is 3~~5mm | ||
| 110 | ** Pure non metal material: <10 mm | ||
| 111 | * Pure liquid without irregular deposition. | ||
| 112 | |||
| 113 | |||
| 114 | == 1.4 Mechanical == | ||
| 115 | |||
| 116 | [[image:image-20220615090910-1.png]] | ||
| 117 | |||
| 118 | |||
| 119 | [[image:image-20220615090910-2.png]] | ||
| 120 | |||
| 121 | |||
| 122 | |||
| 123 | == 1.5 Install LDDS20 == | ||
| 124 | |||
| 125 | |||
| 126 | (% style="color:blue" %)**Step 1**(%%): Choose the installation point. | ||
| 127 | |||
| 128 | LDDS20 (% style="color:red" %)**MUST**(%%) be installed on the container bottom middle position. | ||
| 129 | |||
| 130 | [[image:image-20220615091045-3.png]] | ||
| 131 | |||
| 132 | |||
| 133 | |||
| 134 | (% style="color:blue" %)**Step 2**(%%): Polish the installation point. | ||
| 135 | |||
| 136 | For Metal Surface with paint, it is important to polish the surface, first use crude sand paper to polish the paint level , then use exquisite sand paper to polish the metal level to make it shine & smooth. | ||
| 137 | |||
| 138 | [[image:image-20220615092010-11.png]] | ||
| 139 | |||
| 140 | |||
| 141 | No polish needed if the container is shine metal surface without paint or non-metal container. | ||
| 142 | |||
| 143 | [[image:image-20220615092044-12.png]] | ||
| 144 | |||
| 145 | |||
| 146 | |||
| 147 | (% style="color:blue" %)**Step3: **(%%)Test the installation point. | ||
| 148 | |||
| 149 | Power on LDDS75, check if the blue LED is on, If the blue LED is on, means the sensor works. Then put ultrasonic coupling paste on the sensor and put it tightly on the installation point. | ||
| 150 | |||
| 151 | |||
| 152 | It is necessary to put the coupling paste between the sensor and the container, otherwise LDDS20 won’t detect the liquid level. | ||
| 153 | |||
| 154 | [[image:1655256160324-178.png]][[image:image-20220615092327-13.png]] | ||
| 155 | |||
| 156 | |||
| 157 | After paste the LDDS20 well, power on LDDS20. In the first 30 seconds of booting, device will check the sensors status and BLUE LED will show the status as below. After 30 seconds, BLUE LED will be off to save battery life. | ||
| 158 | |||
| 159 | |||
| 160 | (% style="color:red" %)**LED Status:** | ||
| 161 | |||
| 162 | * Onboard LED: When power on device, the onboard LED will fast blink 4 times which means detect the sensor well. | ||
| 163 | |||
| 164 | * (% style="color:blue" %)BLUE LED(% style="color:red" %) always ON(%%): Sensor is power on but doesn’t detect liquid. There is problem in installation point. | ||
| 165 | * (% style="color:blue" %)BLUE LED(% style="color:red" %) slowly blinking(%%): Sensor detects Liquid Level, The installation point is good. | ||
| 166 | |||
| 167 | LDDS20 will enter into low power mode at 30 seconds after system reset or power on, Blue LED will be off after that. | ||
| 168 | |||
| 169 | |||
| 170 | (% style="color:red" %)**Note 2:** | ||
| 171 | |||
| 172 | (% style="color:red" %)Ultrasonic coupling paste (%%) is subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally. | ||
| 173 | |||
| 174 | |||
| 175 | |||
| 176 | (% style="color:blue" %)**Step4: **(%%)Install use Epoxy ab glue. | ||
| 177 | |||
| 178 | Prepare Eproxy AB glue. | ||
| 179 | |||
| 180 | Put Eproxy AB glue in the sensor and press it hard on the container installation point. | ||
| 181 | |||
| 182 | Reset LDDS20 and see if the BLUE LED is slowly blinking. | ||
| 183 | |||
| 184 | [[image:image-20220615091045-8.png||height="226" width="380"]] [[image:image-20220615091045-9.png||height="239" width="339"]] | ||
| 185 | |||
| 186 | |||
| 187 | (% style="color:red" %)**Note 1:** | ||
| 188 | |||
| 189 | Eproxy AB glue needs 3~~ 5 minutes to stable attached. we can use other glue material to keep it in the position. | ||
| 190 | |||
| 191 | |||
| 192 | (% style="color:red" %)**Note 2:** | ||
| 193 | |||
| 194 | (% style="color:red" %)Eproxy AB glue(%%) is subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally. | ||
| 195 | |||
| 196 | |||
| 197 | |||
| 198 | == 1.6 Applications == | ||
| 199 | |||
| 200 | * Smart liquid control solution. | ||
| 201 | * Smart liquefied gas solution. | ||
| 202 | |||
| 203 | |||
| 204 | |||
| 205 | == 1.7 Precautions == | ||
| 206 | |||
| 207 | * At room temperature, containers of different materials, such as steel, glass, iron, ceramics, non-foamed plastics and other dense materials, have different detection blind areas and detection limit heights. | ||
| 208 | * For containers of the same material at room temperature, the detection blind zone and detection limit height are also different for the thickness of the container. | ||
| 209 | * When the detected liquid level exceeds the effective detection value of the sensor, and the liquid level of the liquid to be measured shakes or tilts, the detected liquid height is unstable. | ||
| 210 | |||
| 211 | |||
| 212 | |||
| 213 | == 1.8 Pin mapping and power on == | ||
| 214 | |||
| 215 | |||
| 216 | [[image:1655257026882-201.png]] | ||
| 217 | |||
| 218 | |||
| 219 | |||
| 220 | = 2. Configure LDDS20 to connect to LoRaWAN network = | ||
| 221 | |||
| 222 | |||
| 223 | == 2.1 How it works == | ||
| 224 | |||
| 225 | ((( | ||
| 226 | The LDDS20 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LDDS20. If there is coverage of the LoRaWAN network, it will automatically join the network via OTAA and start to send the sensor value. | ||
| 227 | ))) | ||
| 228 | |||
| 229 | ((( | ||
| 230 | In case you can't set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.A0UsingtheATCommands"]]to set the keys in the LDDS20. | ||
| 231 | ))) | ||
| 232 | |||
| 233 | |||
| 234 | |||
| 235 | == 2.2 Quick guide to connect to LoRaWAN server (OTAA) == | ||
| 236 | |||
| 237 | ((( | ||
| 238 | Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example. | ||
| 239 | ))) | ||
| 240 | |||
| 241 | ((( | ||
| 242 | [[image:1655257698953-697.png]] | ||
| 243 | ))) | ||
| 244 | |||
| 245 | ((( | ||
| 246 | The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server. | ||
| 247 | ))) | ||
| 248 | |||
| 249 | ((( | ||
| 250 | |||
| 251 | |||
| 252 | (% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LDDS20. | ||
| 253 | ))) | ||
| 254 | |||
| 255 | ((( | ||
| 256 | Each LDDS20 is shipped with a sticker with the default device keys, user can find this sticker in the box. it looks like below. | ||
| 257 | ))) | ||
| 258 | |||
| 259 | [[image:image-20220607170145-1.jpeg]] | ||
| 260 | |||
| 261 | |||
| 262 | ((( | ||
| 263 | For OTAA registration, we need to set **APP EUI/ APP KEY/ DEV EUI**. Some server might no need to set APP EUI. | ||
| 264 | ))) | ||
| 265 | |||
| 266 | ((( | ||
| 267 | Enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot: | ||
| 268 | ))) | ||
| 269 | |||
| 270 | ((( | ||
| 271 | |||
| 272 | |||
| 273 | **Add APP EUI in the application** | ||
| 274 | ))) | ||
| 275 | |||
| 276 | [[image:image-20220610161353-4.png]] | ||
| 277 | |||
| 278 | [[image:image-20220610161353-5.png]] | ||
| 279 | |||
| 280 | [[image:image-20220610161353-6.png]] | ||
| 281 | |||
| 282 | |||
| 283 | [[image:image-20220610161353-7.png]] | ||
| 284 | |||
| 285 | |||
| 286 | |||
| 287 | You can also choose to create the device manually. | ||
| 288 | |||
| 289 | [[image:image-20220610161538-8.png]] | ||
| 290 | |||
| 291 | |||
| 292 | |||
| 293 | **Add APP KEY and DEV EUI** | ||
| 294 | |||
| 295 | [[image:image-20220610161538-9.png]] | ||
| 296 | |||
| 297 | |||
| 298 | |||
| 299 | (% style="color:blue" %)**Step 2**(%%): Power on LDDS20 | ||
| 300 | |||
| 301 | |||
| 302 | Put a Jumper on JP2 to power on the device. ( The Switch must be in FLASH position). | ||
| 303 | |||
| 304 | [[image:image-20220615095102-14.png]] | ||
| 305 | |||
| 306 | |||
| 307 | |||
| 308 | ((( | ||
| 309 | (% style="color:blue" %)**Step 3**(%%)**:** The LDDS20 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel. | ||
| 310 | ))) | ||
| 311 | |||
| 312 | [[image:1654849068701-275.png]] | ||
| 313 | |||
| 314 | |||
| 315 | |||
| 316 | == 2.3 Uplink Payload == | ||
| 317 | |||
| 318 | ((( | ||
| 319 | ((( | ||
| 320 | LDDS20 will uplink payload via LoRaWAN with below payload format: | ||
| 321 | |||
| 322 | Uplink payload includes in total 8 bytes. | ||
| 323 | Payload for firmware version v1.1.4. . Before v1.1.3, there is only 5 bytes: BAT and Distance(Please check manual v1.2.0 if you have 5 bytes payload). | ||
| 324 | ))) | ||
| 325 | ))) | ||
| 326 | |||
| 327 | ((( | ||
| 328 | |||
| 329 | ))) | ||
| 330 | |||
| 331 | (% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %) | ||
| 332 | |=(% style="width: 62.5px;" %)((( | ||
| 333 | **Size (bytes)** | ||
| 334 | )))|=(% style="width: 62.5px;" %)**2**|=**2**|=1|=2|=**1** | ||
| 335 | |(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|((( | ||
| 336 | [[Distance>>||anchor="H2.3.2A0Distance"]] | ||
| 337 | |||
| 338 | (unit: mm) | ||
| 339 | )))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|((( | ||
| 340 | [[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]] | ||
| 341 | )))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]] | ||
| 342 | |||
| 343 | [[image:1654850511545-399.png]] | ||
| 344 | |||
| 345 | |||
| 346 | |||
| 347 | === 2.3.1 Battery Info === | ||
| 348 | |||
| 349 | |||
| 350 | Check the battery voltage for LDDS20. | ||
| 351 | |||
| 352 | Ex1: 0x0B45 = 2885mV | ||
| 353 | |||
| 354 | Ex2: 0x0B49 = 2889mV | ||
| 355 | |||
| 356 | |||
| 357 | |||
| 358 | === 2.3.2 Distance === | ||
| 359 | |||
| 360 | ((( | ||
| 361 | Get the distance. Flat object range 20mm - 2000mm. | ||
| 362 | ))) | ||
| 363 | |||
| 364 | ((( | ||
| 365 | For example, if the data you get from the register is __0x06 0x05__, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** 0605(H) = 1541 (D) = 1541 mm.** | ||
| 366 | ))) | ||
| 367 | |||
| 368 | * If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor. | ||
| 369 | * If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid. | ||
| 370 | |||
| 371 | |||
| 372 | |||
| 373 | === 2.3.3 Interrupt Pin === | ||
| 374 | |||
| 375 | This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2A0SetInterruptMode"]] for the hardware and software set up. | ||
| 376 | |||
| 377 | **Example:** | ||
| 378 | |||
| 379 | 0x00: Normal uplink packet. | ||
| 380 | |||
| 381 | 0x01: Interrupt Uplink Packet. | ||
| 382 | |||
| 383 | |||
| 384 | |||
| 385 | === 2.3.4 DS18B20 Temperature sensor === | ||
| 386 | |||
| 387 | This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature. | ||
| 388 | |||
| 389 | **Example**: | ||
| 390 | |||
| 391 | If payload is: 0105H: (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree | ||
| 392 | |||
| 393 | If payload is: FF3FH : (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees. | ||
| 394 | |||
| 395 | (% style="color:red" %)Note: DS18B20 feature is supported in the hardware version > v1.3 which made since early of 2021. | ||
| 396 | |||
| 397 | |||
| 398 | |||
| 399 | === 2.3.5 Sensor Flag === | ||
| 400 | |||
| 401 | ((( | ||
| 402 | 0x01: Detect Ultrasonic Sensor | ||
| 403 | ))) | ||
| 404 | |||
| 405 | ((( | ||
| 406 | 0x00: No Ultrasonic Sensor | ||
| 407 | ))) | ||
| 408 | |||
| 409 | |||
| 410 | |||
| 411 | === 2.3.6 Decode payload in The Things Network === | ||
| 412 | |||
| 413 | While using TTN network, you can add the payload format to decode the payload. | ||
| 414 | |||
| 415 | |||
| 416 | [[image:1654850829385-439.png]] | ||
| 417 | |||
| 418 | The payload decoder function for TTN V3 is here: | ||
| 419 | |||
| 420 | ((( | ||
| 421 | LDDS20 TTN V3 Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDDS20/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]] | ||
| 422 | ))) | ||
| 423 | |||
| 424 | |||
| 425 | |||
| 426 | == 2.4 Uplink Interval == | ||
| 427 | |||
| 428 | The LDDS75 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]] | ||
| 429 | |||
| 430 | |||
| 431 | |||
| 432 | == 2.5 Show Data in DataCake IoT Server == | ||
| 433 | |||
| 434 | ((( | ||
| 435 | [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps: | ||
| 436 | ))) | ||
| 437 | |||
| 438 | ((( | ||
| 439 | |||
| 440 | ))) | ||
| 441 | |||
| 442 | ((( | ||
| 443 | (% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.** | ||
| 444 | ))) | ||
| 445 | |||
| 446 | ((( | ||
| 447 | (% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:** | ||
| 448 | ))) | ||
| 449 | |||
| 450 | |||
| 451 | [[image:1654592790040-760.png]] | ||
| 452 | |||
| 453 | |||
| 454 | [[image:1654592800389-571.png]] | ||
| 455 | |||
| 456 | |||
| 457 | (% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.** | ||
| 458 | |||
| 459 | (% style="color:blue" %)**Step 4**(%%)**: Search the LDDS75 and add DevEUI.** | ||
| 460 | |||
| 461 | [[image:1654851029373-510.png]] | ||
| 462 | |||
| 463 | |||
| 464 | After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake. | ||
| 465 | |||
| 466 | [[image:image-20220610165129-11.png||height="595" width="1088"]] | ||
| 467 | |||
| 468 | |||
| 469 | |||
| 470 | == 2.6 Frequency Plans == | ||
| 471 | |||
| 472 | ((( | ||
| 473 | The LDDS75 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets. | ||
| 474 | ))) | ||
| 475 | |||
| 476 | |||
| 477 | |||
| 478 | === 2.6.1 EU863-870 (EU868) === | ||
| 479 | |||
| 480 | ((( | ||
| 481 | (% style="color:blue" %)**Uplink:** | ||
| 482 | ))) | ||
| 483 | |||
| 484 | ((( | ||
| 485 | 868.1 - SF7BW125 to SF12BW125 | ||
| 486 | ))) | ||
| 487 | |||
| 488 | ((( | ||
| 489 | 868.3 - SF7BW125 to SF12BW125 and SF7BW250 | ||
| 490 | ))) | ||
| 491 | |||
| 492 | ((( | ||
| 493 | 868.5 - SF7BW125 to SF12BW125 | ||
| 494 | ))) | ||
| 495 | |||
| 496 | ((( | ||
| 497 | 867.1 - SF7BW125 to SF12BW125 | ||
| 498 | ))) | ||
| 499 | |||
| 500 | ((( | ||
| 501 | 867.3 - SF7BW125 to SF12BW125 | ||
| 502 | ))) | ||
| 503 | |||
| 504 | ((( | ||
| 505 | 867.5 - SF7BW125 to SF12BW125 | ||
| 506 | ))) | ||
| 507 | |||
| 508 | ((( | ||
| 509 | 867.7 - SF7BW125 to SF12BW125 | ||
| 510 | ))) | ||
| 511 | |||
| 512 | ((( | ||
| 513 | 867.9 - SF7BW125 to SF12BW125 | ||
| 514 | ))) | ||
| 515 | |||
| 516 | ((( | ||
| 517 | 868.8 - FSK | ||
| 518 | ))) | ||
| 519 | |||
| 520 | ((( | ||
| 521 | |||
| 522 | ))) | ||
| 523 | |||
| 524 | ((( | ||
| 525 | (% style="color:blue" %)**Downlink:** | ||
| 526 | ))) | ||
| 527 | |||
| 528 | ((( | ||
| 529 | Uplink channels 1-9 (RX1) | ||
| 530 | ))) | ||
| 531 | |||
| 532 | ((( | ||
| 533 | 869.525 - SF9BW125 (RX2 downlink only) | ||
| 534 | ))) | ||
| 535 | |||
| 536 | |||
| 537 | |||
| 538 | === 2.6.2 US902-928(US915) === | ||
| 539 | |||
| 540 | ((( | ||
| 541 | Used in USA, Canada and South America. Default use CHE=2 | ||
| 542 | |||
| 543 | (% style="color:blue" %)**Uplink:** | ||
| 544 | |||
| 545 | 903.9 - SF7BW125 to SF10BW125 | ||
| 546 | |||
| 547 | 904.1 - SF7BW125 to SF10BW125 | ||
| 548 | |||
| 549 | 904.3 - SF7BW125 to SF10BW125 | ||
| 550 | |||
| 551 | 904.5 - SF7BW125 to SF10BW125 | ||
| 552 | |||
| 553 | 904.7 - SF7BW125 to SF10BW125 | ||
| 554 | |||
| 555 | 904.9 - SF7BW125 to SF10BW125 | ||
| 556 | |||
| 557 | 905.1 - SF7BW125 to SF10BW125 | ||
| 558 | |||
| 559 | 905.3 - SF7BW125 to SF10BW125 | ||
| 560 | |||
| 561 | |||
| 562 | (% style="color:blue" %)**Downlink:** | ||
| 563 | |||
| 564 | 923.3 - SF7BW500 to SF12BW500 | ||
| 565 | |||
| 566 | 923.9 - SF7BW500 to SF12BW500 | ||
| 567 | |||
| 568 | 924.5 - SF7BW500 to SF12BW500 | ||
| 569 | |||
| 570 | 925.1 - SF7BW500 to SF12BW500 | ||
| 571 | |||
| 572 | 925.7 - SF7BW500 to SF12BW500 | ||
| 573 | |||
| 574 | 926.3 - SF7BW500 to SF12BW500 | ||
| 575 | |||
| 576 | 926.9 - SF7BW500 to SF12BW500 | ||
| 577 | |||
| 578 | 927.5 - SF7BW500 to SF12BW500 | ||
| 579 | |||
| 580 | 923.3 - SF12BW500(RX2 downlink only) | ||
| 581 | |||
| 582 | |||
| 583 | |||
| 584 | ))) | ||
| 585 | |||
| 586 | === 2.6.3 CN470-510 (CN470) === | ||
| 587 | |||
| 588 | ((( | ||
| 589 | Used in China, Default use CHE=1 | ||
| 590 | ))) | ||
| 591 | |||
| 592 | ((( | ||
| 593 | (% style="color:blue" %)**Uplink:** | ||
| 594 | ))) | ||
| 595 | |||
| 596 | ((( | ||
| 597 | 486.3 - SF7BW125 to SF12BW125 | ||
| 598 | ))) | ||
| 599 | |||
| 600 | ((( | ||
| 601 | 486.5 - SF7BW125 to SF12BW125 | ||
| 602 | ))) | ||
| 603 | |||
| 604 | ((( | ||
| 605 | 486.7 - SF7BW125 to SF12BW125 | ||
| 606 | ))) | ||
| 607 | |||
| 608 | ((( | ||
| 609 | 486.9 - SF7BW125 to SF12BW125 | ||
| 610 | ))) | ||
| 611 | |||
| 612 | ((( | ||
| 613 | 487.1 - SF7BW125 to SF12BW125 | ||
| 614 | ))) | ||
| 615 | |||
| 616 | ((( | ||
| 617 | 487.3 - SF7BW125 to SF12BW125 | ||
| 618 | ))) | ||
| 619 | |||
| 620 | ((( | ||
| 621 | 487.5 - SF7BW125 to SF12BW125 | ||
| 622 | ))) | ||
| 623 | |||
| 624 | ((( | ||
| 625 | 487.7 - SF7BW125 to SF12BW125 | ||
| 626 | ))) | ||
| 627 | |||
| 628 | ((( | ||
| 629 | |||
| 630 | ))) | ||
| 631 | |||
| 632 | ((( | ||
| 633 | (% style="color:blue" %)**Downlink:** | ||
| 634 | ))) | ||
| 635 | |||
| 636 | ((( | ||
| 637 | 506.7 - SF7BW125 to SF12BW125 | ||
| 638 | ))) | ||
| 639 | |||
| 640 | ((( | ||
| 641 | 506.9 - SF7BW125 to SF12BW125 | ||
| 642 | ))) | ||
| 643 | |||
| 644 | ((( | ||
| 645 | 507.1 - SF7BW125 to SF12BW125 | ||
| 646 | ))) | ||
| 647 | |||
| 648 | ((( | ||
| 649 | 507.3 - SF7BW125 to SF12BW125 | ||
| 650 | ))) | ||
| 651 | |||
| 652 | ((( | ||
| 653 | 507.5 - SF7BW125 to SF12BW125 | ||
| 654 | ))) | ||
| 655 | |||
| 656 | ((( | ||
| 657 | 507.7 - SF7BW125 to SF12BW125 | ||
| 658 | ))) | ||
| 659 | |||
| 660 | ((( | ||
| 661 | 507.9 - SF7BW125 to SF12BW125 | ||
| 662 | ))) | ||
| 663 | |||
| 664 | ((( | ||
| 665 | 508.1 - SF7BW125 to SF12BW125 | ||
| 666 | ))) | ||
| 667 | |||
| 668 | ((( | ||
| 669 | 505.3 - SF12BW125 (RX2 downlink only) | ||
| 670 | ))) | ||
| 671 | |||
| 672 | |||
| 673 | |||
| 674 | === 2.6.4 AU915-928(AU915) === | ||
| 675 | |||
| 676 | ((( | ||
| 677 | Default use CHE=2 | ||
| 678 | |||
| 679 | (% style="color:blue" %)**Uplink:** | ||
| 680 | |||
| 681 | 916.8 - SF7BW125 to SF12BW125 | ||
| 682 | |||
| 683 | 917.0 - SF7BW125 to SF12BW125 | ||
| 684 | |||
| 685 | 917.2 - SF7BW125 to SF12BW125 | ||
| 686 | |||
| 687 | 917.4 - SF7BW125 to SF12BW125 | ||
| 688 | |||
| 689 | 917.6 - SF7BW125 to SF12BW125 | ||
| 690 | |||
| 691 | 917.8 - SF7BW125 to SF12BW125 | ||
| 692 | |||
| 693 | 918.0 - SF7BW125 to SF12BW125 | ||
| 694 | |||
| 695 | 918.2 - SF7BW125 to SF12BW125 | ||
| 696 | |||
| 697 | |||
| 698 | (% style="color:blue" %)**Downlink:** | ||
| 699 | |||
| 700 | 923.3 - SF7BW500 to SF12BW500 | ||
| 701 | |||
| 702 | 923.9 - SF7BW500 to SF12BW500 | ||
| 703 | |||
| 704 | 924.5 - SF7BW500 to SF12BW500 | ||
| 705 | |||
| 706 | 925.1 - SF7BW500 to SF12BW500 | ||
| 707 | |||
| 708 | 925.7 - SF7BW500 to SF12BW500 | ||
| 709 | |||
| 710 | 926.3 - SF7BW500 to SF12BW500 | ||
| 711 | |||
| 712 | 926.9 - SF7BW500 to SF12BW500 | ||
| 713 | |||
| 714 | 927.5 - SF7BW500 to SF12BW500 | ||
| 715 | |||
| 716 | 923.3 - SF12BW500(RX2 downlink only) | ||
| 717 | |||
| 718 | |||
| 719 | |||
| 720 | ))) | ||
| 721 | |||
| 722 | === 2.6.5 AS920-923 & AS923-925 (AS923) === | ||
| 723 | |||
| 724 | ((( | ||
| 725 | (% style="color:blue" %)**Default Uplink channel:** | ||
| 726 | ))) | ||
| 727 | |||
| 728 | ((( | ||
| 729 | 923.2 - SF7BW125 to SF10BW125 | ||
| 730 | ))) | ||
| 731 | |||
| 732 | ((( | ||
| 733 | 923.4 - SF7BW125 to SF10BW125 | ||
| 734 | ))) | ||
| 735 | |||
| 736 | ((( | ||
| 737 | |||
| 738 | ))) | ||
| 739 | |||
| 740 | ((( | ||
| 741 | (% style="color:blue" %)**Additional Uplink Channel**: | ||
| 742 | ))) | ||
| 743 | |||
| 744 | ((( | ||
| 745 | (OTAA mode, channel added by JoinAccept message) | ||
| 746 | ))) | ||
| 747 | |||
| 748 | ((( | ||
| 749 | |||
| 750 | ))) | ||
| 751 | |||
| 752 | ((( | ||
| 753 | (% style="color:blue" %)**AS920~~AS923 for Japan, Malaysia, Singapore**: | ||
| 754 | ))) | ||
| 755 | |||
| 756 | ((( | ||
| 757 | 922.2 - SF7BW125 to SF10BW125 | ||
| 758 | ))) | ||
| 759 | |||
| 760 | ((( | ||
| 761 | 922.4 - SF7BW125 to SF10BW125 | ||
| 762 | ))) | ||
| 763 | |||
| 764 | ((( | ||
| 765 | 922.6 - SF7BW125 to SF10BW125 | ||
| 766 | ))) | ||
| 767 | |||
| 768 | ((( | ||
| 769 | 922.8 - SF7BW125 to SF10BW125 | ||
| 770 | ))) | ||
| 771 | |||
| 772 | ((( | ||
| 773 | 923.0 - SF7BW125 to SF10BW125 | ||
| 774 | ))) | ||
| 775 | |||
| 776 | ((( | ||
| 777 | 922.0 - SF7BW125 to SF10BW125 | ||
| 778 | ))) | ||
| 779 | |||
| 780 | ((( | ||
| 781 | |||
| 782 | ))) | ||
| 783 | |||
| 784 | ((( | ||
| 785 | (% style="color:blue" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**: | ||
| 786 | ))) | ||
| 787 | |||
| 788 | ((( | ||
| 789 | 923.6 - SF7BW125 to SF10BW125 | ||
| 790 | ))) | ||
| 791 | |||
| 792 | ((( | ||
| 793 | 923.8 - SF7BW125 to SF10BW125 | ||
| 794 | ))) | ||
| 795 | |||
| 796 | ((( | ||
| 797 | 924.0 - SF7BW125 to SF10BW125 | ||
| 798 | ))) | ||
| 799 | |||
| 800 | ((( | ||
| 801 | 924.2 - SF7BW125 to SF10BW125 | ||
| 802 | ))) | ||
| 803 | |||
| 804 | ((( | ||
| 805 | 924.4 - SF7BW125 to SF10BW125 | ||
| 806 | ))) | ||
| 807 | |||
| 808 | ((( | ||
| 809 | 924.6 - SF7BW125 to SF10BW125 | ||
| 810 | ))) | ||
| 811 | |||
| 812 | ((( | ||
| 813 | |||
| 814 | ))) | ||
| 815 | |||
| 816 | ((( | ||
| 817 | (% style="color:blue" %)**Downlink:** | ||
| 818 | ))) | ||
| 819 | |||
| 820 | ((( | ||
| 821 | Uplink channels 1-8 (RX1) | ||
| 822 | ))) | ||
| 823 | |||
| 824 | ((( | ||
| 825 | 923.2 - SF10BW125 (RX2) | ||
| 826 | ))) | ||
| 827 | |||
| 828 | |||
| 829 | |||
| 830 | === 2.6.6 KR920-923 (KR920) === | ||
| 831 | |||
| 832 | ((( | ||
| 833 | (% style="color:blue" %)**Default channel:** | ||
| 834 | ))) | ||
| 835 | |||
| 836 | ((( | ||
| 837 | 922.1 - SF7BW125 to SF12BW125 | ||
| 838 | ))) | ||
| 839 | |||
| 840 | ((( | ||
| 841 | 922.3 - SF7BW125 to SF12BW125 | ||
| 842 | ))) | ||
| 843 | |||
| 844 | ((( | ||
| 845 | 922.5 - SF7BW125 to SF12BW125 | ||
| 846 | ))) | ||
| 847 | |||
| 848 | ((( | ||
| 849 | |||
| 850 | ))) | ||
| 851 | |||
| 852 | ((( | ||
| 853 | (% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)** | ||
| 854 | ))) | ||
| 855 | |||
| 856 | ((( | ||
| 857 | 922.1 - SF7BW125 to SF12BW125 | ||
| 858 | ))) | ||
| 859 | |||
| 860 | ((( | ||
| 861 | 922.3 - SF7BW125 to SF12BW125 | ||
| 862 | ))) | ||
| 863 | |||
| 864 | ((( | ||
| 865 | 922.5 - SF7BW125 to SF12BW125 | ||
| 866 | ))) | ||
| 867 | |||
| 868 | ((( | ||
| 869 | 922.7 - SF7BW125 to SF12BW125 | ||
| 870 | ))) | ||
| 871 | |||
| 872 | ((( | ||
| 873 | 922.9 - SF7BW125 to SF12BW125 | ||
| 874 | ))) | ||
| 875 | |||
| 876 | ((( | ||
| 877 | 923.1 - SF7BW125 to SF12BW125 | ||
| 878 | ))) | ||
| 879 | |||
| 880 | ((( | ||
| 881 | 923.3 - SF7BW125 to SF12BW125 | ||
| 882 | ))) | ||
| 883 | |||
| 884 | ((( | ||
| 885 | |||
| 886 | ))) | ||
| 887 | |||
| 888 | ((( | ||
| 889 | (% style="color:blue" %)**Downlink:** | ||
| 890 | ))) | ||
| 891 | |||
| 892 | ((( | ||
| 893 | Uplink channels 1-7(RX1) | ||
| 894 | ))) | ||
| 895 | |||
| 896 | ((( | ||
| 897 | 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125) | ||
| 898 | ))) | ||
| 899 | |||
| 900 | |||
| 901 | |||
| 902 | === 2.6.7 IN865-867 (IN865) === | ||
| 903 | |||
| 904 | ((( | ||
| 905 | (% style="color:blue" %)**Uplink:** | ||
| 906 | ))) | ||
| 907 | |||
| 908 | ((( | ||
| 909 | 865.0625 - SF7BW125 to SF12BW125 | ||
| 910 | ))) | ||
| 911 | |||
| 912 | ((( | ||
| 913 | 865.4025 - SF7BW125 to SF12BW125 | ||
| 914 | ))) | ||
| 915 | |||
| 916 | ((( | ||
| 917 | 865.9850 - SF7BW125 to SF12BW125 | ||
| 918 | ))) | ||
| 919 | |||
| 920 | ((( | ||
| 921 | |||
| 922 | ))) | ||
| 923 | |||
| 924 | ((( | ||
| 925 | (% style="color:blue" %)**Downlink:** | ||
| 926 | ))) | ||
| 927 | |||
| 928 | ((( | ||
| 929 | Uplink channels 1-3 (RX1) | ||
| 930 | ))) | ||
| 931 | |||
| 932 | ((( | ||
| 933 | 866.550 - SF10BW125 (RX2) | ||
| 934 | ))) | ||
| 935 | |||
| 936 | |||
| 937 | |||
| 938 | == 2.7 LED Indicator == | ||
| 939 | |||
| 940 | The LDDS75 has an internal LED which is to show the status of different state. | ||
| 941 | |||
| 942 | |||
| 943 | * Blink once when device power on. | ||
| 944 | * The device detects the sensor and flashes 5 times. | ||
| 945 | * Solid ON for 5 seconds once device successful Join the network. | ||
| 946 | * Blink once when device transmit a packet. | ||
| 947 | |||
| 948 | == 2.8 Firmware Change Log == | ||
| 949 | |||
| 950 | |||
| 951 | ((( | ||
| 952 | **Firmware download link: **[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]] | ||
| 953 | ))) | ||
| 954 | |||
| 955 | ((( | ||
| 956 | |||
| 957 | ))) | ||
| 958 | |||
| 959 | ((( | ||
| 960 | **Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]] | ||
| 961 | ))) | ||
| 962 | |||
| 963 | |||
| 964 | |||
| 965 | == 2.9 Mechanical == | ||
| 966 | |||
| 967 | |||
| 968 | [[image:image-20220610172003-1.png]] | ||
| 969 | |||
| 970 | |||
| 971 | [[image:image-20220610172003-2.png]] | ||
| 972 | |||
| 973 | |||
| 974 | |||
| 975 | == 2.10 Battery Analysis == | ||
| 976 | |||
| 977 | === 2.10.1 Battery Type === | ||
| 978 | |||
| 979 | The LDDS75 battery is a combination of a 4000mAh or 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter. | ||
| 980 | |||
| 981 | |||
| 982 | The battery related documents as below: | ||
| 983 | |||
| 984 | * ((( | ||
| 985 | [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]], | ||
| 986 | ))) | ||
| 987 | * ((( | ||
| 988 | [[Lithium-Thionyl Chloride Battery datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]], | ||
| 989 | ))) | ||
| 990 | * ((( | ||
| 991 | [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]] | ||
| 992 | ))) | ||
| 993 | |||
| 994 | [[image:image-20220610172400-3.png]] | ||
| 995 | |||
| 996 | |||
| 997 | |||
| 998 | === 2.10.2 Replace the battery === | ||
| 999 | |||
| 1000 | ((( | ||
| 1001 | You can change the battery in the LDDS75.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board. | ||
| 1002 | ))) | ||
| 1003 | |||
| 1004 | ((( | ||
| 1005 | |||
| 1006 | ))) | ||
| 1007 | |||
| 1008 | ((( | ||
| 1009 | The default battery pack of LDDS75 includes a ER18505 plus super capacitor. If user can't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes) | ||
| 1010 | ))) | ||
| 1011 | |||
| 1012 | |||
| 1013 | |||
| 1014 | = 3. Configure LDDS75 via AT Command or LoRaWAN Downlink = | ||
| 1015 | |||
| 1016 | ((( | ||
| 1017 | ((( | ||
| 1018 | Use can configure LDDS75 via AT Command or LoRaWAN Downlink. | ||
| 1019 | ))) | ||
| 1020 | ))) | ||
| 1021 | |||
| 1022 | * ((( | ||
| 1023 | ((( | ||
| 1024 | AT Command Connection: See [[FAQ>>||anchor="H4.A0FAQ"]]. | ||
| 1025 | ))) | ||
| 1026 | ))) | ||
| 1027 | * ((( | ||
| 1028 | ((( | ||
| 1029 | LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]] | ||
| 1030 | ))) | ||
| 1031 | ))) | ||
| 1032 | |||
| 1033 | ((( | ||
| 1034 | ((( | ||
| 1035 | |||
| 1036 | ))) | ||
| 1037 | |||
| 1038 | ((( | ||
| 1039 | There are two kinds of commands to configure LDDS75, they are: | ||
| 1040 | ))) | ||
| 1041 | ))) | ||
| 1042 | |||
| 1043 | * ((( | ||
| 1044 | ((( | ||
| 1045 | (% style="color:#4f81bd" %)** General Commands**. | ||
| 1046 | ))) | ||
| 1047 | ))) | ||
| 1048 | |||
| 1049 | ((( | ||
| 1050 | ((( | ||
| 1051 | These commands are to configure: | ||
| 1052 | ))) | ||
| 1053 | ))) | ||
| 1054 | |||
| 1055 | * ((( | ||
| 1056 | ((( | ||
| 1057 | General system settings like: uplink interval. | ||
| 1058 | ))) | ||
| 1059 | ))) | ||
| 1060 | * ((( | ||
| 1061 | ((( | ||
| 1062 | LoRaWAN protocol & radio related command. | ||
| 1063 | ))) | ||
| 1064 | ))) | ||
| 1065 | |||
| 1066 | ((( | ||
| 1067 | ((( | ||
| 1068 | They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]] | ||
| 1069 | ))) | ||
| 1070 | ))) | ||
| 1071 | |||
| 1072 | ((( | ||
| 1073 | ((( | ||
| 1074 | |||
| 1075 | ))) | ||
| 1076 | ))) | ||
| 1077 | |||
| 1078 | * ((( | ||
| 1079 | ((( | ||
| 1080 | (% style="color:#4f81bd" %)** Commands special design for LDDS75** | ||
| 1081 | ))) | ||
| 1082 | ))) | ||
| 1083 | |||
| 1084 | ((( | ||
| 1085 | ((( | ||
| 1086 | These commands only valid for LDDS75, as below: | ||
| 1087 | ))) | ||
| 1088 | ))) | ||
| 1089 | |||
| 1090 | |||
| 1091 | |||
| 1092 | == 3.1 Access AT Commands == | ||
| 1093 | |||
| 1094 | LDDS75 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS75 for using AT command, as below. | ||
| 1095 | |||
| 1096 | [[image:image-20220610172924-4.png||height="483" width="988"]] | ||
| 1097 | |||
| 1098 | |||
| 1099 | Or if you have below board, use below connection: | ||
| 1100 | |||
| 1101 | |||
| 1102 | [[image:image-20220610172924-5.png]] | ||
| 1103 | |||
| 1104 | |||
| 1105 | ((( | ||
| 1106 | In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LDDS75. LDDS75 will output system info once power on as below: | ||
| 1107 | ))) | ||
| 1108 | |||
| 1109 | |||
| 1110 | [[image:image-20220610172924-6.png||height="601" width="860"]] | ||
| 1111 | |||
| 1112 | |||
| 1113 | |||
| 1114 | == 3.2 Set Transmit Interval Time == | ||
| 1115 | |||
| 1116 | Feature: Change LoRaWAN End Node Transmit Interval. | ||
| 1117 | |||
| 1118 | (% style="color:#037691" %)**AT Command: AT+TDC** | ||
| 1119 | |||
| 1120 | [[image:image-20220610173409-7.png]] | ||
| 1121 | |||
| 1122 | |||
| 1123 | ((( | ||
| 1124 | (% style="color:#037691" %)**Downlink Command: 0x01** | ||
| 1125 | ))) | ||
| 1126 | |||
| 1127 | ((( | ||
| 1128 | ((( | ||
| 1129 | Format: Command Code (0x01) followed by 3 bytes time value. | ||
| 1130 | |||
| 1131 | ((( | ||
| 1132 | If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. | ||
| 1133 | ))) | ||
| 1134 | |||
| 1135 | * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds | ||
| 1136 | * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds | ||
| 1137 | ))) | ||
| 1138 | ))) | ||
| 1139 | |||
| 1140 | |||
| 1141 | |||
| 1142 | |||
| 1143 | |||
| 1144 | == 3.3 Set Interrupt Mode == | ||
| 1145 | |||
| 1146 | Feature, Set Interrupt mode for GPIO_EXIT. | ||
| 1147 | |||
| 1148 | (% style="color:#037691" %)**Downlink Command: AT+INTMOD** | ||
| 1149 | |||
| 1150 | [[image:image-20220610174917-9.png]] | ||
| 1151 | |||
| 1152 | |||
| 1153 | (% style="color:#037691" %)**Downlink Command: 0x06** | ||
| 1154 | |||
| 1155 | Format: Command Code (0x06) followed by 3 bytes. | ||
| 1156 | |||
| 1157 | ((( | ||
| 1158 | This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06. | ||
| 1159 | ))) | ||
| 1160 | |||
| 1161 | * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode | ||
| 1162 | * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger | ||
| 1163 | |||
| 1164 | = 4. FAQ = | ||
| 1165 | |||
| 1166 | == 4.1 What is the frequency plan for LDDS75? == | ||
| 1167 | |||
| 1168 | LDDS75 use the same frequency as other Dragino products. User can see the detail from this link: [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]] | ||
| 1169 | |||
| 1170 | |||
| 1171 | |||
| 1172 | == 4.2 How to change the LoRa Frequency Bands/Region == | ||
| 1173 | |||
| 1174 | You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]]. | ||
| 1175 | When downloading the images, choose the required image file for download. | ||
| 1176 | |||
| 1177 | |||
| 1178 | |||
| 1179 | == 4.3 Can I use LDDS75 in condensation environment? == | ||
| 1180 | |||
| 1181 | LDDS75 is not suitable to be used in condensation environment. Condensation on the LDDS75 probe will affect the reading and always got 0. | ||
| 1182 | |||
| 1183 | |||
| 1184 | |||
| 1185 | = 5. Trouble Shooting = | ||
| 1186 | |||
| 1187 | == 5.1 Why I can’t join TTN V3 in US915 / AU915 bands? == | ||
| 1188 | |||
| 1189 | It is due to channel mapping. Please see below link: [[Frequency band>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] | ||
| 1190 | |||
| 1191 | |||
| 1192 | == 5.2 AT Command input doesn't work == | ||
| 1193 | |||
| 1194 | In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string. | ||
| 1195 | |||
| 1196 | ((( | ||
| 1197 | |||
| 1198 | ))) | ||
| 1199 | |||
| 1200 | |||
| 1201 | = 6. Order Info = | ||
| 1202 | |||
| 1203 | |||
| 1204 | Part Number **:** (% style="color:blue" %)**LDDS75-XX-YY** | ||
| 1205 | |||
| 1206 | |||
| 1207 | (% style="color:blue" %)**XX**(%%)**: **The default frequency band | ||
| 1208 | |||
| 1209 | * (% style="color:red" %)**AS923 **(%%)**:** LoRaWAN AS923 band | ||
| 1210 | * (% style="color:red" %)**AU915 **(%%)**:** LoRaWAN AU915 band | ||
| 1211 | * (% style="color:red" %)**EU433 **(%%)**:** LoRaWAN EU433 band | ||
| 1212 | * (% style="color:red" %)**EU868 **(%%)**:** LoRaWAN EU868 band | ||
| 1213 | * (% style="color:red" %)**KR920 **(%%)**:** LoRaWAN KR920 band | ||
| 1214 | * (% style="color:red" %)**US915 **(%%)**:** LoRaWAN US915 band | ||
| 1215 | * (% style="color:red" %)**IN865 **(%%)**:** LoRaWAN IN865 band | ||
| 1216 | * (% style="color:red" %)**CN470 **(%%)**:** LoRaWAN CN470 band | ||
| 1217 | |||
| 1218 | (% style="color:blue" %)**YY**(%%): Battery Option | ||
| 1219 | |||
| 1220 | * (% style="color:red" %)**4 **(%%)**: **4000mAh battery | ||
| 1221 | * (% style="color:red" %)**8 **(%%)**:** 8500mAh battery | ||
| 1222 | |||
| 1223 | = 7. Packing Info = | ||
| 1224 | |||
| 1225 | |||
| 1226 | **Package Includes**: | ||
| 1227 | |||
| 1228 | * LDDS75 LoRaWAN Distance Detection Sensor x 1 | ||
| 1229 | |||
| 1230 | **Dimension and weight**: | ||
| 1231 | |||
| 1232 | * Device Size: cm | ||
| 1233 | * Device Weight: g | ||
| 1234 | * Package Size / pcs : cm | ||
| 1235 | * Weight / pcs : g | ||
| 1236 | |||
| 1237 | = 8. Support = | ||
| 1238 | |||
| 1239 | * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule. | ||
| 1240 | * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]. |