<
From version < 94.5 >
edited by Xiaoling
on 2022/06/10 10:43
To version < 95.2 >
edited by Xiaoling
on 2022/06/10 11:03
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -913,10 +913,10 @@
913 913  
914 914  
915 915  
916 -= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
916 += 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
917 917  
918 918  (((
919 -Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
919 +Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
920 920  )))
921 921  
922 922  * (((
... ... @@ -927,7 +927,9 @@
927 927  )))
928 928  
929 929  (((
930 -There are two kinds of commands to configure LSPH01, they are:
930 +
931 +
932 +There are two kinds of commands to configure LLDS12, they are:
931 931  )))
932 932  
933 933  * (((
... ... @@ -946,7 +946,7 @@
946 946  )))
947 947  
948 948  (((
949 -They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
951 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
950 950  )))
951 951  
952 952  (((
... ... @@ -954,16 +954,16 @@
954 954  )))
955 955  
956 956  * (((
957 -(% style="color:#4f81bd" %)** Commands special design for LSPH01**
959 +(% style="color:#4f81bd" %)** Commands special design for LLDS12**
958 958  )))
959 959  
960 960  (((
961 -These commands only valid for LSPH01, as below:
963 +These commands only valid for LLDS12, as below:
962 962  )))
963 963  
964 964  
965 965  
966 -== 3.1 Set Transmit Interval Time ==
968 +== 4.1  Set Transmit Interval Time ==
967 967  
968 968  Feature: Change LoRaWAN End Node Transmit Interval.
969 969  
... ... @@ -995,15 +995,17 @@
995 995  
996 996  )))
997 997  
998 -== 3.2 Set Interrupt Mode ==
1000 +== 4.2  Set Interrupt Mode ==
999 999  
1000 1000  Feature, Set Interrupt mode for GPIO_EXIT.
1001 1001  
1002 1002  (% style="color:#037691" %)**AT Command: AT+INTMOD**
1003 1003  
1004 -[[image:image-20220607171716-9.png]]
1006 +[[image:image-20220610105806-2.png]]
1005 1005  
1006 1006  
1009 +
1010 +
1007 1007  (((
1008 1008  (% style="color:#037691" %)**Downlink Command: 0x06**
1009 1009  )))
... ... @@ -1023,20 +1023,10 @@
1023 1023  Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1024 1024  )))
1025 1025  
1026 -(((
1027 -
1028 -)))
1029 1029  
1030 1030  
1032 +== 4.3  Get Firmware Version Info ==
1031 1031  
1032 -== 3.3 Calibrate Sensor ==
1033 -
1034 -Detail See [[Calibration Guide>>||anchor="H2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
1035 -
1036 -
1037 -
1038 -== 3.4 Get Firmware Version Info ==
1039 -
1040 1040  Feature: use downlink to get firmware version.
1041 1041  
1042 1042  (% style="color:#037691" %)**Downlink Command: 0x26**
image-20220610105806-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +15.5 KB
Content
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0