Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -913,10 +913,10 @@
913	913
914	914
915	915
916		-= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
	916	+= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
917	917
918	918	(((
919		-Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
	919	+Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
920	920	)))
921	921
922	922	* (((
...	...	@@ -927,6 +927,8 @@
927	927	)))
928	928
929	929	(((
	930	+
	931	+
930	930	There are two kinds of commands to configure LSPH01, they are:
931	931	)))
932	932
...	...	@@ -946,7 +946,7 @@
946	946	)))
947	947
948	948	(((
949		-They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	951	+They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>path:/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
950	950	)))
951	951
952	952	(((
...	...	@@ -954,7 +954,7 @@
954	954	)))
955	955
956	956	* (((
957		-(% style="color:#4f81bd" %)** Commands special design for LSPH01**
	959	+(% style="color:#4f81bd" %)** Commands special design for LLDS12**
958	958	)))
959	959
960	960	(((
...	...	@@ -963,7 +963,7 @@
963	963
964	964
965	965
966		-== 3.1 Set Transmit Interval Time ==
	968	+== 4.1  Set Transmit Interval Time ==
967	967
968	968	Feature: Change LoRaWAN End Node Transmit Interval.
969	969
...	...	@@ -995,7 +995,7 @@
995	995
996	996	)))
997	997
998		-== 3.2 Set Interrupt Mode ==
	1000	+== 4.2  Set Interrupt Mode ==
999	999
1000	1000	Feature, Set Interrupt mode for GPIO_EXIT.
1001	1001
...	...	@@ -1023,20 +1023,10 @@
1023	1023	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1024	1024	)))
1025	1025
1026		-(((
1027		-
1028		-)))
1029	1029
1030	1030
	1030	+== 4.3  Get Firmware Version Info ==
1031	1031
1032		-== 3.3 Calibrate Sensor ==
1033		-
1034		-Detail See [[Calibration Guide>>||anchor="H2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
1035		-
1036		-
1037		-
1038		-== 3.4 Get Firmware Version Info ==
1039		-
1040	1040	Feature: use downlink to get firmware version.
1041	1041
1042	1042	(% style="color:#037691" %)**Downlink Command: 0x26**
...	...	@@ -1117,12 +1117,12 @@
1117	1117
1118	1118
1119	1119
1120		-= 4. Battery & How to replace =
	1112	+= 5.  Battery & How to replace =
1121	1121
1122		-== 4.1 Battery Type ==
	1114	+== 5.1  Battery Type ==
1123	1123
1124	1124	(((
1125		-LSPH01 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
	1117	+LLDS12 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
1126	1126	)))
1127	1127
1128	1128	(((
...	...	@@ -1132,13 +1132,13 @@
1132	1132	[[image:1654593587246-335.png]]
1133	1133
1134	1134
1135		-Minimum Working Voltage for the LSPH01:
	1127	+Minimum Working Voltage for the LLDS12:
1136	1136
1137		-LSPH01:  2.45v ~~ 3.6v
	1129	+LLDS12:  2.45v ~~ 3.6v
1138	1138
1139	1139
1140	1140
1141		-== 4.2 Replace Battery ==
	1133	+== 5.2  Replace Battery ==
1142	1142
1143	1143	(((
1144	1144	Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
...	...	@@ -1150,7 +1150,7 @@
1150	1150
1151	1151
1152	1152
1153		-== 4.3 Power Consumption Analyze ==
	1145	+== 5.3  Power Consumption Analyze ==
1154	1154
1155	1155	(((
1156	1156	Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
...	...	@@ -1193,7 +1193,7 @@
1193	1193
1194	1194
1195	1195
1196		-=== 4.3.1 ​Battery Note ===
	1188	+=== 5.3.1  ​Battery Note ===
1197	1197
1198	1198	(((
1199	1199	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
...	...	@@ -1201,23 +1201,23 @@
1201	1201
1202	1202
1203	1203
1204		-=== ​4.3.2 Replace the battery ===
	1196	+=== ​5.3.2  Replace the battery ===
1205	1205
1206	1206	(((
1207		-You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	1199	+You can change the battery in the LLDS12.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
1208	1208	)))
1209	1209
1210	1210	(((
1211		-The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	1203	+The default battery pack of LLDS12 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
1212	1212	)))
1213	1213
1214	1214
1215	1215
1216		-= 5. Use AT Command =
	1208	+= 6.  Use AT Command =
1217	1217
1218		-== 5.1 Access AT Commands ==
	1210	+== 6.1  Access AT Commands ==
1219	1219
1220		-LSPH01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSPH01 for using AT command, as below.
	1212	+LLDS12 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LLDS12 for using AT command, as below.
1221	1221
1222	1222	[[image:1654593668970-604.png]]
1223	1223
...	...	@@ -1240,9 +1240,9 @@
1240	1240	Valid AT Command please check [[Configure Device>>||anchor="H3.ConfigureLSPH01viaATCommandorLoRaWANDownlink"]].
1241	1241
1242	1242
1243		-= 6.  FAQ =
	1235	+= 7.  FAQ =
1244	1244
1245		-== 6.1  How to change the LoRa Frequency Bands/Region ==
	1237	+== 7.1  How to change the LoRa Frequency Bands/Region ==
1246	1246
1247	1247	You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
1248	1248	When downloading the images, choose the required image file for download. ​
...	...	@@ -1252,6 +1252,7 @@
1252	1252
1253	1253	== 8.1  AT Commands input doesn’t work ==
1254	1254
	1247	+
1255	1255	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1256	1256
1257	1257
...	...	@@ -1258,18 +1258,31 @@
1258	1258	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==
1259	1259
1260	1260
1261		-**(% style="color:blue" %)Cause ①**(%%)：Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
	1254	+(((
	1255	+(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
	1256	+)))
1262	1262
	1258	+(((
1263	1263	Troubleshooting: Please avoid use of this product under such circumstance in practice.
	1260	+)))
1264	1264
	1262	+(((
	1263	+
	1264	+)))
1265	1265
1266		-**(% style="color:blue" %)Cause ②**(%%): The IR-pass filters are blocked.
	1266	+(((
	1267	+(% style="color:blue" %)**Cause ②**(%%)**: **The IR-pass filters are blocked.
	1268	+)))
1267	1267
1268		-Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter
	1270	+(((
	1271	+Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter.
	1272	+)))
1269	1269
1270	1270
	1275	+
1271	1271	= 9.  Order Info =
1272	1272
	1278	+
1273	1273	Part Number: (% style="color:blue" %)**LLDS12-XX**
1274	1274
1275	1275
...	...	@@ -1285,7 +1285,6 @@
1285	1285	* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1286	1286
1287	1287
1288		-
1289	1289	= 10. ​ Packing Info =
1290	1290
1291	1291
...	...	@@ -1301,7 +1301,6 @@
1301	1301	* Weight / pcs : g
1302	1302
1303	1303
1304		-
1305	1305	= 11.  ​Support =
1306	1306
1307	1307	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.