Skip to Content
Last modified by Mengting Qiu on 2025/08/06 17:02
From version 175.20
edited by Xiaoling
on 2022/06/15 11:08
Change comment: There is no comment for this version
To version 173.3
edited by Xiaoling
on 2022/06/15 10:11
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -100,9 +100,6 @@
100 100  * IP66 Waterproof Enclosure
101 101  * 8500mAh Battery for long term use
102 102  
103 -
104 -
105 -
106 106  == 1.3  Suitable Container & Liquid ==
107 107  
108 108  * Solid Wall container such as: steel, iron, glass, ceramics, non-foaming plastics etc.
... ... @@ -112,9 +112,6 @@
112 112  ** Pure non metal material: <10 mm
113 113  * Pure liquid without irregular deposition.
114 114  
115 -
116 -
117 -
118 118  == 1.4  Mechanical ==
119 119  
120 120  [[image:image-20220615090910-1.png]]
... ... @@ -205,8 +205,6 @@
205 205  * Smart liquefied gas solution.
206 206  
207 207  
208 -
209 -
210 210  == 1.7  Precautions ==
211 211  
212 212  * At room temperature, containers of different materials, such as steel, glass, iron, ceramics, non-foamed plastics and other dense materials, have different detection blind areas and detection limit heights.
... ... @@ -213,6 +213,7 @@
213 213  * For containers of the same material at room temperature, the detection blind zone and detection limit height are also different for the thickness of the container.
214 214  * When the detected liquid level exceeds the effective detection value of the sensor, and the liquid level of the liquid to be measured shakes or tilts, the detected liquid height is unstable.
215 215  
208 +
216 216  == 1.8  Pin mapping and power on ==
217 217  
218 218  
... ... @@ -371,6 +371,7 @@
371 371  * If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
372 372  * If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid.
373 373  
367 +
374 374  === 2.3.3  Interrupt Pin ===
375 375  
376 376  This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2A0SetInterruptMode"]] for the hardware and software set up.
... ... @@ -414,7 +414,7 @@
414 414  While using TTN network, you can add the payload format to decode the payload.
415 415  
416 416  
417 -[[image:1655261164557-670.png]]
411 +[[image:1654850829385-439.png]]
418 418  
419 419  The payload decoder function for TTN V3 is here:
420 420  
... ... @@ -481,7 +481,7 @@
481 481  
482 482  (% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
483 483  
484 -(% style="color:blue" %)**Step 4**(%%)**: Search the LDDS75 and add DevEUI.(% style="color:red" %)(Note: LDDS20 use same payload as LDDS75)(%%)**
478 +(% style="color:blue" %)**Step 4**(%%)**: Search the LDDS75 and add DevEUI.**
485 485  
486 486  [[image:1654851029373-510.png]]
487 487  
... ... @@ -492,227 +492,682 @@
492 492  
493 493  
494 494  
495 -== 2.6  LED Indicator ==
489 +== 2.6  Frequency Plans ==
496 496  
497 -The LDDS20 has an internal LED which is to show the status of different state.
491 +(((
492 +The LDDS75 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
493 +)))
498 498  
499 499  
500 -* Blink once when device power on.
501 -* The device detects the sensor and flashes 5 times.
502 -* Solid ON for 5 seconds once device successful Join the network.
503 -* Blink once when device transmit a packet.
504 504  
505 -== 2.7  ​Firmware Change Log ==
497 +=== 2.6.1  EU863-870 (EU868) ===
506 506  
499 +(((
500 +(% style="color:blue" %)**Uplink:**
501 +)))
507 507  
508 508  (((
509 -**Firmware download link:  **[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
504 +868.1 - SF7BW125 to SF12BW125
510 510  )))
511 511  
512 512  (((
508 +868.3 - SF7BW125 to SF12BW125 and SF7BW250
509 +)))
510 +
511 +(((
512 +868.5 - SF7BW125 to SF12BW125
513 +)))
514 +
515 +(((
516 +867.1 - SF7BW125 to SF12BW125
517 +)))
518 +
519 +(((
520 +867.3 - SF7BW125 to SF12BW125
521 +)))
522 +
523 +(((
524 +867.5 - SF7BW125 to SF12BW125
525 +)))
526 +
527 +(((
528 +867.7 - SF7BW125 to SF12BW125
529 +)))
530 +
531 +(((
532 +867.9 - SF7BW125 to SF12BW125
533 +)))
534 +
535 +(((
536 +868.8 - FSK
537 +)))
538 +
539 +(((
513 513  
514 514  )))
515 515  
516 516  (((
517 -**Firmware Upgrade Method:  [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]**
544 +(% style="color:blue" %)**Downlink:**
518 518  )))
519 519  
547 +(((
548 +Uplink channels 1-9 (RX1)
549 +)))
520 520  
551 +(((
552 +869.525 - SF9BW125 (RX2 downlink only)
553 +)))
521 521  
522 -== 2.8  Battery Analysis ==
523 523  
524 524  
557 +=== 2.6.2  US902-928(US915) ===
525 525  
559 +(((
560 +Used in USA, Canada and South America. Default use CHE=2
526 526  
527 -=== 2.8.1  Battery Type ===
562 +(% style="color:blue" %)**Uplink:**
528 528  
529 -The LDDS20 battery is a combination of a 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
564 +903.9 - SF7BW125 to SF10BW125
530 530  
566 +904.1 - SF7BW125 to SF10BW125
531 531  
532 -The battery related documents as below:
568 +904.3 - SF7BW125 to SF10BW125
533 533  
534 -* (((
535 -[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],
570 +904.5 - SF7BW125 to SF10BW125
571 +
572 +904.7 - SF7BW125 to SF10BW125
573 +
574 +904.9 - SF7BW125 to SF10BW125
575 +
576 +905.1 - SF7BW125 to SF10BW125
577 +
578 +905.3 - SF7BW125 to SF10BW125
579 +
580 +
581 +(% style="color:blue" %)**Downlink:**
582 +
583 +923.3 - SF7BW500 to SF12BW500
584 +
585 +923.9 - SF7BW500 to SF12BW500
586 +
587 +924.5 - SF7BW500 to SF12BW500
588 +
589 +925.1 - SF7BW500 to SF12BW500
590 +
591 +925.7 - SF7BW500 to SF12BW500
592 +
593 +926.3 - SF7BW500 to SF12BW500
594 +
595 +926.9 - SF7BW500 to SF12BW500
596 +
597 +927.5 - SF7BW500 to SF12BW500
598 +
599 +923.3 - SF12BW500(RX2 downlink only)
600 +
601 +
602 +
536 536  )))
537 -* (((
538 -[[Lithium-Thionyl Chloride Battery  datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]],
604 +
605 +=== 2.6.3  CN470-510 (CN470) ===
606 +
607 +(((
608 +Used in China, Default use CHE=1
539 539  )))
540 -* (((
541 -[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
610 +
611 +(((
612 +(% style="color:blue" %)**Uplink:**
542 542  )))
543 543  
544 - [[image:image-20220615102527-16.png]]
615 +(((
616 +486.3 - SF7BW125 to SF12BW125
617 +)))
545 545  
619 +(((
620 +486.5 - SF7BW125 to SF12BW125
621 +)))
546 546  
623 +(((
624 +486.7 - SF7BW125 to SF12BW125
625 +)))
547 547  
548 -== 2.8.2  Battery Note ==
627 +(((
628 +486.9 - SF7BW125 to SF12BW125
629 +)))
549 549  
550 -The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to uplink data, then the battery life may be decreased.
631 +(((
632 +487.1 - SF7BW125 to SF12BW125
633 +)))
551 551  
635 +(((
636 +487.3 - SF7BW125 to SF12BW125
637 +)))
552 552  
639 +(((
640 +487.5 - SF7BW125 to SF12BW125
641 +)))
553 553  
554 -=== 2.8.3  Replace the battery ===
643 +(((
644 +487.7 - SF7BW125 to SF12BW125
645 +)))
555 555  
556 556  (((
557 -You can change the battery in the LDDS75.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board.
648 +
558 558  )))
559 559  
560 560  (((
652 +(% style="color:blue" %)**Downlink:**
653 +)))
654 +
655 +(((
656 +506.7 - SF7BW125 to SF12BW125
657 +)))
658 +
659 +(((
660 +506.9 - SF7BW125 to SF12BW125
661 +)))
662 +
663 +(((
664 +507.1 - SF7BW125 to SF12BW125
665 +)))
666 +
667 +(((
668 +507.3 - SF7BW125 to SF12BW125
669 +)))
670 +
671 +(((
672 +507.5 - SF7BW125 to SF12BW125
673 +)))
674 +
675 +(((
676 +507.7 - SF7BW125 to SF12BW125
677 +)))
678 +
679 +(((
680 +507.9 - SF7BW125 to SF12BW125
681 +)))
682 +
683 +(((
684 +508.1 - SF7BW125 to SF12BW125
685 +)))
686 +
687 +(((
688 +505.3 - SF12BW125 (RX2 downlink only)
689 +)))
690 +
691 +
692 +
693 +=== 2.6.4  AU915-928(AU915) ===
694 +
695 +(((
696 +Default use CHE=2
697 +
698 +(% style="color:blue" %)**Uplink:**
699 +
700 +916.8 - SF7BW125 to SF12BW125
701 +
702 +917.0 - SF7BW125 to SF12BW125
703 +
704 +917.2 - SF7BW125 to SF12BW125
705 +
706 +917.4 - SF7BW125 to SF12BW125
707 +
708 +917.6 - SF7BW125 to SF12BW125
709 +
710 +917.8 - SF7BW125 to SF12BW125
711 +
712 +918.0 - SF7BW125 to SF12BW125
713 +
714 +918.2 - SF7BW125 to SF12BW125
715 +
716 +
717 +(% style="color:blue" %)**Downlink:**
718 +
719 +923.3 - SF7BW500 to SF12BW500
720 +
721 +923.9 - SF7BW500 to SF12BW500
722 +
723 +924.5 - SF7BW500 to SF12BW500
724 +
725 +925.1 - SF7BW500 to SF12BW500
726 +
727 +925.7 - SF7BW500 to SF12BW500
728 +
729 +926.3 - SF7BW500 to SF12BW500
730 +
731 +926.9 - SF7BW500 to SF12BW500
732 +
733 +927.5 - SF7BW500 to SF12BW500
734 +
735 +923.3 - SF12BW500(RX2 downlink only)
736 +
737 +
561 561  
562 562  )))
563 563  
741 +=== 2.6.5  AS920-923 & AS923-925 (AS923) ===
742 +
564 564  (((
565 -The default battery pack of LDDS75 includes a ER18505 plus super capacitor. If user can't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
744 +(% style="color:blue" %)**Default Uplink channel:**
566 566  )))
567 567  
747 +(((
748 +923.2 - SF7BW125 to SF10BW125
749 +)))
568 568  
751 +(((
752 +923.4 - SF7BW125 to SF10BW125
753 +)))
569 569  
570 -== 2.8.4  Battery Life Analyze ==
755 +(((
756 +
757 +)))
571 571  
572 -Dragino battery powered products are all run in Low Power mode. User can check the guideline from this link to calculate the estimate battery life:
759 +(((
760 +(% style="color:blue" %)**Additional Uplink Channel**:
761 +)))
573 573  
574 -[[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf]]
763 +(((
764 +(OTAA mode, channel added by JoinAccept message)
765 +)))
575 575  
767 +(((
768 +
769 +)))
576 576  
771 +(((
772 +(% style="color:blue" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
773 +)))
577 577  
578 -= 3.  Using the AT Commands =
775 +(((
776 +922.2 - SF7BW125 to SF10BW125
777 +)))
579 579  
580 580  (((
780 +922.4 - SF7BW125 to SF10BW125
781 +)))
782 +
581 581  (((
784 +922.6 - SF7BW125 to SF10BW125
785 +)))
786 +
787 +(((
788 +922.8 - SF7BW125 to SF10BW125
789 +)))
790 +
791 +(((
792 +923.0 - SF7BW125 to SF10BW125
793 +)))
794 +
795 +(((
796 +922.0 - SF7BW125 to SF10BW125
797 +)))
798 +
799 +(((
582 582  
583 583  )))
802 +
803 +(((
804 +(% style="color:blue" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
584 584  )))
585 585  
586 -== 3.1  Access AT Commands ==
807 +(((
808 +923.6 - SF7BW125 to SF10BW125
809 +)))
587 587  
588 -LDDS20 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS20 for using AT command, as below.
811 +(((
812 +923.8 - SF7BW125 to SF10BW125
813 +)))
589 589  
815 +(((
816 +924.0 - SF7BW125 to SF10BW125
817 +)))
590 590  
591 -[[image:image-20220610172924-4.png||height="483" width="988"]]
819 +(((
820 +924.2 - SF7BW125 to SF10BW125
821 +)))
592 592  
823 +(((
824 +924.4 - SF7BW125 to SF10BW125
825 +)))
593 593  
594 -Or if you have below board, use below connection:
827 +(((
828 +924.6 - SF7BW125 to SF10BW125
829 +)))
595 595  
831 +(((
832 +
833 +)))
596 596  
597 -[[image:image-20220610172924-5.png]]
835 +(((
836 +(% style="color:blue" %)**Downlink:**
837 +)))
598 598  
839 +(((
840 +Uplink channels 1-8 (RX1)
841 +)))
599 599  
600 600  (((
601 -In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LDDS20. LDDS20 will output system info once power on as below:
844 +923.2 - SF10BW125 (RX2)
602 602  )))
603 603  
604 604  
605 - [[image:image-20220610172924-6.png||height="601" width="860"]]
606 606  
607 -Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]].
849 +=== 2.6.6  KR920-923 (KR920) ===
608 608  
851 +(((
852 +(% style="color:blue" %)**Default channel:**
853 +)))
609 609  
610 -AT+<CMD>?  :  Help on <CMD>
855 +(((
856 +922.1 - SF7BW125 to SF12BW125
857 +)))
611 611  
612 -AT+<CMD>  :  Run <CMD>
859 +(((
860 +922.3 - SF7BW125 to SF12BW125
861 +)))
613 613  
614 -AT+<CMD>=<value>  :  Set the value
863 +(((
864 +922.5 - SF7BW125 to SF12BW125
865 +)))
615 615  
616 -AT+<CMD>=?  :  Get the value
867 +(((
868 +
869 +)))
617 617  
871 +(((
872 +(% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
873 +)))
618 618  
619 -(% style="color:#037691" %)** General Commands :**     
875 +(((
876 +922.1 - SF7BW125 to SF12BW125
877 +)))
620 620  
621 -AT  :  Attention       
879 +(((
880 +922.3 - SF7BW125 to SF12BW125
881 +)))
622 622  
623 -AT?  :  Short Help     
883 +(((
884 +922.5 - SF7BW125 to SF12BW125
885 +)))
624 624  
625 -ATZ :  MCU Reset    
887 +(((
888 +922.7 - SF7BW125 to SF12BW125
889 +)))
626 626  
627 -AT+TDC :  Application Data Transmission Interval 
891 +(((
892 +922.9 - SF7BW125 to SF12BW125
893 +)))
628 628  
895 +(((
896 +923.1 - SF7BW125 to SF12BW125
897 +)))
629 629  
630 -(% style="color:#037691" %)** Keys, IDs and EUIs management :**
899 +(((
900 +923.3 - SF7BW125 to SF12BW125
901 +)))
631 631  
632 -AT+APPEUI  :  Application EUI      
903 +(((
904 +
905 +)))
633 633  
634 -AT+APPKEY  :  Application Key     
907 +(((
908 +(% style="color:blue" %)**Downlink:**
909 +)))
635 635  
636 -AT+APPSKEY  :  Application Session Key
911 +(((
912 +Uplink channels 1-7(RX1)
913 +)))
637 637  
638 -AT+DADDR :  Device Address     
915 +(((
916 +921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
917 +)))
639 639  
640 -AT+DEUI :  Device EUI     
641 641  
642 -AT+NWKID  :  Network ID (You can enter this command change only after successful network connection) 
643 643  
644 -AT+NWKSKEY  : Network Session Key Joining and sending date on LoRa network  
921 +=== 2.6.7  IN865-867 (IN865) ===
645 645  
646 -AT+CFM :  Confirm Mode       
923 +(((
924 +(% style="color:blue" %)**Uplink:**
925 +)))
647 647  
648 -AT+CFS :  Confirm Status       
927 +(((
928 +865.0625 - SF7BW125 to SF12BW125
929 +)))
649 649  
650 -AT+JOIN  :  Join LoRa? Network       
931 +(((
932 +865.4025 - SF7BW125 to SF12BW125
933 +)))
651 651  
652 -AT+NJM  :  LoRa? Network Join Mode    
935 +(((
936 +865.9850 - SF7BW125 to SF12BW125
937 +)))
653 653  
654 -AT+NJS  :  LoRa? Network Join Status    
939 +(((
940 +
941 +)))
655 655  
656 -AT+RECV  :  Print Last Received Data in Raw Format
943 +(((
944 +(% style="color:blue" %)**Downlink:**
945 +)))
657 657  
658 -AT+RECVB :  Print Last Received Data in Binary Format      
947 +(((
948 +Uplink channels 1-3 (RX1)
949 +)))
659 659  
660 -AT+SEND  :  Send Text Data      
951 +(((
952 +866.550 - SF10BW125 (RX2)
953 +)))
661 661  
662 -AT+SENB  :  Send Hexadecimal Data
663 663  
664 664  
665 -(% style="color:#037691" %)** LoRa Network Management :**
957 +== 2.7  LED Indicator ==
666 666  
667 -AT+ADR  :  Adaptive Rate
959 +The LDDS75 has an internal LED which is to show the status of different state.
668 668  
669 -AT+CLASS  :  LoRa Class(Currently only support class A
670 670  
671 -AT+DCS  :  Duty Cycle Setting 
962 +* Blink once when device power on.
963 +* The device detects the sensor and flashes 5 times.
964 +* Solid ON for 5 seconds once device successful Join the network.
965 +* Blink once when device transmit a packet.
672 672  
673 -AT+DR  :  Data Rate (Can Only be Modified after ADR=0)     
967 +== 2.8  ​Firmware Change Log ==
674 674  
675 -AT+FCD  :  Frame Counter Downlink       
676 676  
677 -AT+FCU  :  Frame Counter Uplink   
970 +(((
971 +**Firmware download link: **[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
972 +)))
678 678  
679 -AT+JN1DL  :  Join Accept Delay1
974 +(((
975 +
976 +)))
680 680  
681 -AT+JN2DL  :  Join Accept Delay2
978 +(((
979 +**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
980 +)))
682 682  
683 -AT+PNM  :  Public Network Mode   
684 684  
685 -AT+RX1DL  :  Receive Delay1      
686 686  
687 -AT+RX2DL  :  Receive Delay2      
984 +== 2.9  Mechanical ==
688 688  
689 -AT+RX2DR  :  Rx2 Window Data Rate 
690 690  
691 -AT+RX2FQ  :  Rx2 Window Frequency
987 +[[image:image-20220610172003-1.png]]
692 692  
693 -AT+TXP  :  Transmit Power
694 694  
990 +[[image:image-20220610172003-2.png]]
695 695  
696 -(% style="color:#037691" %)** Information :**
697 697  
698 -AT+RSSI  :  RSSI of the Last Received Packet   
699 699  
700 -AT+SNR  :  SNR of the Last Received Packet   
994 +== 2.10  Battery Analysis ==
701 701  
702 -AT+VER  :  Image Version and Frequency Band       
996 +=== 2.10.1  Battery Type ===
703 703  
704 -AT+FDR  :  Factory Data Reset
998 +The LDDS75 battery is a combination of a 4000mAh or 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
705 705  
706 -AT+PORT  :  Application Port    
707 707  
708 -AT+CHS  :  Get or Set Frequency (Unit: Hz) for Single Channel Mode
1001 +The battery related documents as below:
709 709  
710 - AT+CHE  :  Get or Set eight channels mode, Only for US915, AU915, CN470
1003 +* (((
1004 +[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
1005 +)))
1006 +* (((
1007 +[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
1008 +)))
1009 +* (((
1010 +[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
1011 +)))
711 711  
1013 + [[image:image-20220610172400-3.png]]
712 712  
713 713  
714 -== 3.2  Set Interrupt Mode ==
715 715  
1017 +=== 2.10.2  Replace the battery ===
1018 +
1019 +(((
1020 +You can change the battery in the LDDS75.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board.
1021 +)))
1022 +
1023 +(((
1024 +
1025 +)))
1026 +
1027 +(((
1028 +The default battery pack of LDDS75 includes a ER18505 plus super capacitor. If user can't find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
1029 +)))
1030 +
1031 +
1032 +
1033 += 3.  Configure LDDS75 via AT Command or LoRaWAN Downlink =
1034 +
1035 +(((
1036 +(((
1037 +Use can configure LDDS75 via AT Command or LoRaWAN Downlink.
1038 +)))
1039 +)))
1040 +
1041 +* (((
1042 +(((
1043 +AT Command Connection: See [[FAQ>>||anchor="H4.A0FAQ"]].
1044 +)))
1045 +)))
1046 +* (((
1047 +(((
1048 +LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
1049 +)))
1050 +)))
1051 +
1052 +(((
1053 +(((
1054 +
1055 +)))
1056 +
1057 +(((
1058 +There are two kinds of commands to configure LDDS75, they are:
1059 +)))
1060 +)))
1061 +
1062 +* (((
1063 +(((
1064 +(% style="color:#4f81bd" %)** General Commands**.
1065 +)))
1066 +)))
1067 +
1068 +(((
1069 +(((
1070 +These commands are to configure:
1071 +)))
1072 +)))
1073 +
1074 +* (((
1075 +(((
1076 +General system settings like: uplink interval.
1077 +)))
1078 +)))
1079 +* (((
1080 +(((
1081 +LoRaWAN protocol & radio related command.
1082 +)))
1083 +)))
1084 +
1085 +(((
1086 +(((
1087 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
1088 +)))
1089 +)))
1090 +
1091 +(((
1092 +(((
1093 +
1094 +)))
1095 +)))
1096 +
1097 +* (((
1098 +(((
1099 +(% style="color:#4f81bd" %)** Commands special design for LDDS75**
1100 +)))
1101 +)))
1102 +
1103 +(((
1104 +(((
1105 +These commands only valid for LDDS75, as below:
1106 +)))
1107 +)))
1108 +
1109 +
1110 +
1111 +== 3.1  Access AT Commands ==
1112 +
1113 +LDDS75 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS75 for using AT command, as below.
1114 +
1115 +[[image:image-20220610172924-4.png||height="483" width="988"]]
1116 +
1117 +
1118 +Or if you have below board, use below connection:
1119 +
1120 +
1121 +[[image:image-20220610172924-5.png]]
1122 +
1123 +
1124 +(((
1125 +In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LDDS75. LDDS75 will output system info once power on as below:
1126 +)))
1127 +
1128 +
1129 + [[image:image-20220610172924-6.png||height="601" width="860"]]
1130 +
1131 +
1132 +
1133 +== 3.2  Set Transmit Interval Time ==
1134 +
1135 +Feature: Change LoRaWAN End Node Transmit Interval.
1136 +
1137 +(% style="color:#037691" %)**AT Command: AT+TDC**
1138 +
1139 +[[image:image-20220610173409-7.png]]
1140 +
1141 +
1142 +(((
1143 +(% style="color:#037691" %)**Downlink Command: 0x01**
1144 +)))
1145 +
1146 +(((
1147 +(((
1148 +Format: Command Code (0x01) followed by 3 bytes time value.
1149 +
1150 +(((
1151 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
1152 +)))
1153 +
1154 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1155 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1156 +)))
1157 +)))
1158 +
1159 +
1160 +
1161 +
1162 +
1163 +== 3.3  Set Interrupt Mode ==
1164 +
716 716  Feature, Set Interrupt mode for GPIO_EXIT.
717 717  
718 718  (% style="color:#037691" %)**Downlink Command: AT+INTMOD**
... ... @@ -731,23 +731,27 @@
731 731  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
732 732  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
733 733  
734 -
735 -
736 736  = 4.  FAQ =
737 737  
738 -== 4.1  What is the frequency plan for LDDS20? ==
1185 +== 4.1  What is the frequency plan for LDDS75? ==
739 739  
740 -LDDS20 use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
1187 +LDDS75 use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
741 741  
742 742  
743 743  
744 744  == 4.2  How to change the LoRa Frequency Bands/Region ==
745 745  
746 -You can follow the instructions for [[how to upgrade image>>||anchor="H2.7A0200BFirmwareChangeLog"]].
1193 +You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
747 747  When downloading the images, choose the required image file for download. ​
748 748  
749 749  
750 750  
1198 +== 4.3  Can I use LDDS75 in condensation environment? ==
1199 +
1200 +LDDS75 is not suitable to be used in condensation environment. Condensation on the LDDS75 probe will affect the reading and always got 0.
1201 +
1202 +
1203 +
751 751  = 5.  Trouble Shooting =
752 752  
753 753  == 5.1  Why I can’t join TTN V3 in US915 / AU915 bands? ==
... ... @@ -767,7 +767,7 @@
767 767  = 6.  Order Info =
768 768  
769 769  
770 -Part Number **:** (% style="color:blue" %)**LDDS20-XX**
1223 +Part Number **:** (% style="color:blue" %)**LDDS75-XX-YY**
771 771  
772 772  
773 773  (% style="color:blue" %)**XX**(%%)**: **The default frequency band
... ... @@ -781,20 +781,18 @@
781 781  * (% style="color:red" %)**IN865 **(%%)**:**  LoRaWAN IN865 band
782 782  * (% style="color:red" %)**CN470 **(%%)**:** LoRaWAN CN470 band
783 783  
1237 +(% style="color:blue" %)**YY**(%%): Battery Option
784 784  
1239 +* (% style="color:red" %)**4 **(%%)**: **4000mAh battery
1240 +* (% style="color:red" %)**8 **(%%)**:** 8500mAh battery
1241 +
785 785  = 7. ​ Packing Info =
786 786  
787 787  
788 788  **Package Includes**:
789 789  
790 -* LDDS20 LoRaWAN Liquid Level Sensor x 1
1247 +* LDDS75 LoRaWAN Distance Detection Sensor x 1
791 791  
792 -
793 -(% style="color:red" %)**Note:**
794 -
795 -(% style="color:red" %)**Ultrasonic coupling paste**(%%) and(% style="color:red" %)** Eproxy AB glue**(%%) are subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally.
796 -
797 -
798 798  **Dimension and weight**:
799 799  
800 800  * Device Size: cm
... ... @@ -802,7 +802,6 @@
802 802  * Package Size / pcs : cm
803 803  * Weight / pcs : g
804 804  
805 -
806 806  = 8.  ​Support =
807 807  
808 808  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1655261164557-670.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -59.2 KB
Content
image-20220615102527-16.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -182.9 KB
Content