Skip to Content
Last modified by Mengting Qiu on 2025/08/06 17:02
From version 175.19
edited by Xiaoling
on 2022/06/15 11:08
Change comment: There is no comment for this version
To version 175.4
edited by Xiaoling
on 2022/06/15 10:49
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -100,9 +100,6 @@
100 100  * IP66 Waterproof Enclosure
101 101  * 8500mAh Battery for long term use
102 102  
103 -
104 -
105 -
106 106  == 1.3  Suitable Container & Liquid ==
107 107  
108 108  * Solid Wall container such as: steel, iron, glass, ceramics, non-foaming plastics etc.
... ... @@ -112,9 +112,6 @@
112 112  ** Pure non metal material: <10 mm
113 113  * Pure liquid without irregular deposition.
114 114  
115 -
116 -
117 -
118 118  == 1.4  Mechanical ==
119 119  
120 120  [[image:image-20220615090910-1.png]]
... ... @@ -368,6 +368,7 @@
368 368  * If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
369 369  * If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid.
370 370  
365 +
371 371  === 2.3.3  Interrupt Pin ===
372 372  
373 373  This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2A0SetInterruptMode"]] for the hardware and software set up.
... ... @@ -499,6 +499,7 @@
499 499  * Solid ON for 5 seconds once device successful Join the network.
500 500  * Blink once when device transmit a packet.
501 501  
497 +
502 502  == 2.7  ​Firmware Change Log ==
503 503  
504 504  
... ... @@ -626,90 +626,120 @@
626 626  
627 627  (% style="color:#037691" %)** Keys, IDs and EUIs management :**
628 628  
629 -AT+APPEUI  :  Application EUI      
625 +AT+APPEUI  : Application EUI      
630 630  
631 -AT+APPKEY  :  Application Key     
627 +AT+APPKEY  : Application Key     
632 632  
633 -AT+APPSKEY  :  Application Session Key
629 +AT+APPSKEY  : Application Session Key
634 634  
635 -AT+DADDR :  Device Address     
631 +AT+DADDR : Device Address     
636 636  
637 -AT+DEUI :  Device EUI     
633 +AT+DEUI : Device EUI     
638 638  
639 -AT+NWKID  :  Network ID (You can enter this command change only after successful network connection) 
635 +AT+NWKID  : Network ID (You can enter this command change only after successful network connection) 
640 640  
641 641  AT+NWKSKEY  : Network Session Key Joining and sending date on LoRa network  
642 642  
643 -AT+CFM :  Confirm Mode       
639 +AT+CFM : Confirm Mode       
644 644  
645 -AT+CFS :  Confirm Status       
641 +AT+CFS : Confirm Status       
646 646  
647 -AT+JOIN  :  Join LoRa? Network       
643 +AT+JOIN  : Join LoRa? Network       
648 648  
649 -AT+NJM  :  LoRa? Network Join Mode    
645 +AT+NJM  : LoRa? Network Join Mode    
650 650  
651 -AT+NJS  :  LoRa? Network Join Status    
647 +AT+NJS  : LoRa? Network Join Status    
652 652  
653 -AT+RECV  :  Print Last Received Data in Raw Format
649 +AT+RECV  : Print Last Received Data in Raw Format
654 654  
655 -AT+RECVB :  Print Last Received Data in Binary Format      
651 +AT+RECVB : Print Last Received Data in Binary Format      
656 656  
657 -AT+SEND  :  Send Text Data      
653 +AT+SEND  : Send Text Data      
658 658  
659 -AT+SENB  :  Send Hexadecimal Data
655 +AT+SENB  : Send Hexadecimal Data
660 660  
661 661  
662 662  (% style="color:#037691" %)** LoRa Network Management :**
663 663  
664 -AT+ADR  :  Adaptive Rate
660 +AT+ADR          : Adaptive Rate
665 665  
666 -AT+CLASS  :  LoRa Class(Currently only support class A
662 +AT+CLASS                : LoRa Class(Currently only support class A
667 667  
668 -AT+DCS  :  Duty Cycle Setting 
664 +AT+DCS           : Duty Cycle Setting 
669 669  
670 -AT+DR  :  Data Rate (Can Only be Modified after ADR=0)     
666 +AT+DR                      : Data Rate (Can Only be Modified after ADR=0)     
671 671  
672 -AT+FCD  :  Frame Counter Downlink       
668 +AT+FCD           : Frame Counter Downlink       
673 673  
674 -AT+FCU  :  Frame Counter Uplink   
670 +AT+FCU           : Frame Counter Uplink   
675 675  
676 -AT+JN1DL  :  Join Accept Delay1
672 +AT+JN1DL                : Join Accept Delay1
677 677  
678 -AT+JN2DL  :  Join Accept Delay2
674 +AT+JN2DL                : Join Accept Delay2
679 679  
680 -AT+PNM  :  Public Network Mode   
676 +AT+PNM                   : Public Network Mode   
681 681  
682 -AT+RX1DL  :  Receive Delay1      
678 +AT+RX1DL                : Receive Delay1      
683 683  
684 -AT+RX2DL  :  Receive Delay2      
680 +AT+RX2DL                : Receive Delay2      
685 685  
686 -AT+RX2DR  :  Rx2 Window Data Rate 
682 +AT+RX2DR               : Rx2 Window Data Rate 
687 687  
688 -AT+RX2FQ  :  Rx2 Window Frequency
684 +AT+RX2FQ               : Rx2 Window Frequency
689 689  
690 -AT+TXP  :  Transmit Power
686 +AT+TXP           : Transmit Power
691 691  
692 692  
693 693  (% style="color:#037691" %)** Information :**
694 694  
695 -AT+RSSI  :  RSSI of the Last Received Packet   
691 +AT+RSSI           : RSSI of the Last Received Packet   
696 696  
697 -AT+SNR  :  SNR of the Last Received Packet   
693 +AT+SNR           : SNR of the Last Received Packet   
698 698  
699 -AT+VER  :  Image Version and Frequency Band       
695 +AT+VER           : Image Version and Frequency Band       
700 700  
701 -AT+FDR  :  Factory Data Reset
697 +AT+FDR           : Factory Data Reset
702 702  
703 -AT+PORT  :  Application Port    
699 +AT+PORT                  : Application Port    
704 704  
705 -AT+CHS  :  Get or Set Frequency (Unit: Hz) for Single Channel Mode
701 +AT+CHS           : Get or Set Frequency (Unit: Hz) for Single Channel Mode
706 706  
707 - AT+CHE  :  Get or Set eight channels mode, Only for US915, AU915, CN470
703 + AT+CHE                   : Get or Set eight channels mode, Only for US915, AU915, CN470
708 708  
709 709  
710 710  
711 -== 3.2  Set Interrupt Mode ==
707 +== 3.2  Set Transmit Interval Time ==
712 712  
709 +Feature: Change LoRaWAN End Node Transmit Interval.
710 +
711 +(% style="color:#037691" %)**AT Command: AT+TDC**
712 +
713 +[[image:image-20220610173409-7.png]]
714 +
715 +
716 +(((
717 +(% style="color:#037691" %)**Downlink Command: 0x01**
718 +)))
719 +
720 +(((
721 +(((
722 +Format: Command Code (0x01) followed by 3 bytes time value.
723 +
724 +(((
725 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
726 +)))
727 +
728 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
729 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
730 +)))
731 +)))
732 +
733 +
734 +
735 +
736 +
737 +== 3.3  Set Interrupt Mode ==
738 +
713 713  Feature, Set Interrupt mode for GPIO_EXIT.
714 714  
715 715  (% style="color:#037691" %)**Downlink Command: AT+INTMOD**
... ... @@ -728,23 +728,27 @@
728 728  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
729 729  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
730 730  
731 -
732 -
733 733  = 4.  FAQ =
734 734  
735 -== 4.1  What is the frequency plan for LDDS20? ==
759 +== 4.1  What is the frequency plan for LDDS75? ==
736 736  
737 -LDDS20 use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
761 +LDDS75 use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
738 738  
739 739  
740 740  
741 741  == 4.2  How to change the LoRa Frequency Bands/Region ==
742 742  
743 -You can follow the instructions for [[how to upgrade image>>||anchor="H2.7A0200BFirmwareChangeLog"]].
767 +You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
744 744  When downloading the images, choose the required image file for download. ​
745 745  
746 746  
747 747  
772 +== 4.3  Can I use LDDS75 in condensation environment? ==
773 +
774 +LDDS75 is not suitable to be used in condensation environment. Condensation on the LDDS75 probe will affect the reading and always got 0.
775 +
776 +
777 +
748 748  = 5.  Trouble Shooting =
749 749  
750 750  == 5.1  Why I can’t join TTN V3 in US915 / AU915 bands? ==
... ... @@ -764,7 +764,7 @@
764 764  = 6.  Order Info =
765 765  
766 766  
767 -Part Number **:** (% style="color:blue" %)**LDDS20-XX**
797 +Part Number **:** (% style="color:blue" %)**LDDS75-XX-YY**
768 768  
769 769  
770 770  (% style="color:blue" %)**XX**(%%)**: **The default frequency band
... ... @@ -778,20 +778,18 @@
778 778  * (% style="color:red" %)**IN865 **(%%)**:**  LoRaWAN IN865 band
779 779  * (% style="color:red" %)**CN470 **(%%)**:** LoRaWAN CN470 band
780 780  
811 +(% style="color:blue" %)**YY**(%%): Battery Option
781 781  
813 +* (% style="color:red" %)**4 **(%%)**: **4000mAh battery
814 +* (% style="color:red" %)**8 **(%%)**:** 8500mAh battery
815 +
782 782  = 7. ​ Packing Info =
783 783  
784 784  
785 785  **Package Includes**:
786 786  
787 -* LDDS20 LoRaWAN Liquid Level Sensor x 1
821 +* LDDS75 LoRaWAN Distance Detection Sensor x 1
788 788  
789 -
790 -(% style="color:red" %)**Note:**
791 -
792 -(% style="color:red" %)**Ultrasonic coupling paste**(%%) and(% style="color:red" %)** Eproxy AB glue**(%%) are subjected in most shipping way. So the default package doesn’t include it and user needs to purchase locally.
793 -
794 -
795 795  **Dimension and weight**:
796 796  
797 797  * Device Size: cm
... ... @@ -799,7 +799,6 @@
799 799  * Package Size / pcs : cm
800 800  * Weight / pcs : g
801 801  
802 -
803 803  = 8.  ​Support =
804 804  
805 805  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.