Skip to Content
Last modified by Mengting Qiu on 2025/08/06 17:02
From version 174.8
edited by Xiaoling
on 2022/06/15 10:37
Change comment: There is no comment for this version
To version 174.6
edited by Xiaoling
on 2022/06/15 10:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -562,27 +562,88 @@
562 562  
563 563  
564 564  
565 -== 2.8.4  Battery Life Analyze ==
565 += 3.  Configure LDDS75 via AT Command or LoRaWAN Downlink =
566 566  
567 -Dragino battery powered products are all run in Low Power mode. User can check the guideline from this link to calculate the estimate battery life:
567 +(((
568 +(((
569 +Use can configure LDDS75 via AT Command or LoRaWAN Downlink.
570 +)))
571 +)))
568 568  
569 -[[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/Battery_Analyze/DRAGINO_Battery_Life_Guide.pdf]]
573 +* (((
574 +(((
575 +AT Command Connection: See [[FAQ>>||anchor="H4.A0FAQ"]].
576 +)))
577 +)))
578 +* (((
579 +(((
580 +LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
581 +)))
582 +)))
570 570  
584 +(((
585 +(((
586 +
587 +)))
571 571  
589 +(((
590 +There are two kinds of commands to configure LDDS75, they are:
591 +)))
592 +)))
572 572  
573 -= 3.  Using the AT Commands =
594 +* (((
595 +(((
596 +(% style="color:#4f81bd" %)** General Commands**.
597 +)))
598 +)))
574 574  
575 575  (((
576 576  (((
602 +These commands are to configure:
603 +)))
604 +)))
605 +
606 +* (((
607 +(((
608 +General system settings like: uplink interval.
609 +)))
610 +)))
611 +* (((
612 +(((
613 +LoRaWAN protocol & radio related command.
614 +)))
615 +)))
616 +
617 +(((
618 +(((
619 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
620 +)))
621 +)))
622 +
623 +(((
624 +(((
577 577  
578 578  )))
579 579  )))
580 580  
581 -== 3.1  Access AT Commands ==
629 +* (((
630 +(((
631 +(% style="color:#4f81bd" %)** Commands special design for LDDS75**
632 +)))
633 +)))
582 582  
583 -LDDS20 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS20 for using AT command, as below.
635 +(((
636 +(((
637 +These commands only valid for LDDS75, as below:
638 +)))
639 +)))
584 584  
585 585  
642 +
643 +== 3.1  Access AT Commands ==
644 +
645 +LDDS75 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LDDS75 for using AT command, as below.
646 +
586 586  [[image:image-20220610172924-4.png||height="483" width="988"]]
587 587  
588 588