Last modified by Xiaoling on 2025/04/27 16:45
<
From version < 150.41 >
edited by Xiaoling
on 2022/06/11 09:14
To version < 154.2 >
edited by Xiaoling
on 2022/06/15 09:00
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LDDS75 - LoRaWAN Distance Detection Sensor User Manual
1 +LDDS20 - LoRaWAN Ultrasonic Liquid Level Sensor User Manual
Content
... ... @@ -1,11 +1,10 @@
1 1  (% style="text-align:center" %)
2 -[[image:1654846127817-788.png]]
2 +[[image:1655254599445-662.png]]
3 3  
4 -**Contents:**
5 5  
6 -{{toc/}}
7 7  
8 8  
7 +**Table of Contents:**
9 9  
10 10  
11 11  
... ... @@ -12,9 +12,11 @@
12 12  
13 13  
14 14  
14 +
15 +
15 15  = 1.  Introduction =
16 16  
17 -== 1.1 ​ What is LoRaWAN Distance Detection Sensor ==
18 +== 1.1 ​ What is LoRaWAN Ultrasonic liquid level Sensor ==
18 18  
19 19  (((
20 20  
... ... @@ -25,42 +25,22 @@
25 25  )))
26 26  
27 27  (((
28 -
29 -)))
30 -
31 -(((
32 32  It detects the distance** (% style="color:#4472c4" %) between the measured object and the sensor(%%)**, and uploads the value via wireless to LoRaWAN IoT Server.
33 33  )))
34 34  
35 35  (((
36 -
37 -)))
38 -
39 -(((
40 40  The LoRa wireless technology used in LDDS75 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
41 41  )))
42 42  
43 43  (((
44 -
45 -)))
46 -
47 -(((
48 48  LDDS75 is powered by (% style="color:#4472c4" %)** 4000mA or 8500mAh Li-SOCI2 battery**(%%); It is designed for long term use up to 10 years*.
49 49  )))
50 50  
51 51  (((
52 -
53 -)))
54 -
55 -(((
56 56  Each LDDS75 pre-loads with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect if there is network coverage, after power on.
57 57  )))
58 58  
59 59  (((
60 -
61 -)))
62 -
63 -(((
64 64  (% style="color:#4472c4" %) * (%%)Actually lifetime depends on network coverage and uplink interval and other factors.
65 65  )))
66 66  )))
... ... @@ -87,7 +87,6 @@
87 87  * 4000mAh or 8500mAh Battery for long term use
88 88  
89 89  
90 -
91 91  == 1.3  Specification ==
92 92  
93 93  === 1.3.1  Rated environmental conditions ===
... ... @@ -95,7 +95,9 @@
95 95  [[image:image-20220610154839-1.png]]
96 96  
97 97  (((
98 -**Remarks: (1) a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);  b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
78 +**Remarks: (1) a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);       **
79 +
80 +**~ b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
99 99  )))
100 100  
101 101  
... ... @@ -110,7 +110,9 @@
110 110  
111 111  
112 112  
95 +(((
113 113  **(2)** **The object to be tested is a "corrugated cardboard box" perpendicular to the central axis of 0 °, and the length * width is 60cm * 50cm.**
97 +)))
114 114  
115 115  
116 116  [[image:1654852175653-550.png]](% style="display:none" %) ** **
... ... @@ -130,8 +130,6 @@
130 130  * Bottom water level monitoring
131 131  
132 132  
133 -
134 -
135 135  == 1.6  Pin mapping and power on ==
136 136  
137 137  
... ... @@ -168,6 +168,8 @@
168 168  )))
169 169  
170 170  (((
153 +
154 +
171 171  (% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LDDS75.
172 172  )))
173 173  
... ... @@ -178,11 +178,19 @@
178 178  [[image:image-20220607170145-1.jpeg]]
179 179  
180 180  
165 +(((
181 181  For OTAA registration, we need to set **APP EUI/ APP KEY/ DEV EUI**. Some server might no need to set APP EUI.
167 +)))
182 182  
169 +(((
183 183  Enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:
171 +)))
184 184  
173 +(((
174 +
175 +
185 185  **Add APP EUI in the application**
177 +)))
186 186  
187 187  [[image:image-20220610161353-4.png]]
188 188  
... ... @@ -225,11 +225,15 @@
225 225  == 2.3  ​Uplink Payload ==
226 226  
227 227  (((
220 +(((
228 228  LDDS75 will uplink payload via LoRaWAN with below payload format: 
222 +)))
229 229  
224 +(((
230 230  Uplink payload includes in total 4 bytes.
231 231  Payload for firmware version v1.1.4. . Before v1.1.3, there is on two fields: BAT and Distance
232 232  )))
228 +)))
233 233  
234 234  (((
235 235  
... ... @@ -264,14 +264,19 @@
264 264  
265 265  === 2.3.2  Distance ===
266 266  
263 +(((
267 267  Get the distance. Flat object range 280mm - 7500mm.
265 +)))
268 268  
267 +(((
269 269  For example, if the data you get from the register is 0x0B 0x05, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** 0B05(H) = 2821 (D) = 2821 mm.**
269 +)))
270 270  
271 271  
272 272  * If the sensor value is 0x0000, it means system doesn’t detect ultrasonic sensor.
273 273  * If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
274 274  
275 +
275 275  === 2.3.3  Interrupt Pin ===
276 276  
277 277  This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3A0SetInterruptMode"]] for the hardware and software set up.
... ... @@ -300,9 +300,13 @@
300 300  
301 301  === 2.3.5  Sensor Flag ===
302 302  
304 +(((
303 303  0x01: Detect Ultrasonic Sensor
306 +)))
304 304  
308 +(((
305 305  0x00: No Ultrasonic Sensor
310 +)))
306 306  
307 307  
308 308  
... ... @@ -315,7 +315,9 @@
315 315  
316 316  The payload decoder function for TTN V3 is here:
317 317  
323 +(((
318 318  LDDS75 TTN V3 Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDDS75/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
325 +)))
319 319  
320 320  
321 321  
... ... @@ -841,13 +841,21 @@
841 841  * Solid ON for 5 seconds once device successful Join the network.
842 842  * Blink once when device transmit a packet.
843 843  
851 +
844 844  == 2.8  ​Firmware Change Log ==
845 845  
846 846  
855 +(((
847 847  **Firmware download link: **[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
857 +)))
848 848  
859 +(((
860 +
861 +)))
849 849  
863 +(((
850 850  **Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
865 +)))
851 851  
852 852  
853 853  
... ... @@ -991,7 +991,9 @@
991 991  [[image:image-20220610172924-5.png]]
992 992  
993 993  
1009 +(((
994 994  In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LDDS75. LDDS75 will output system info once power on as below:
1011 +)))
995 995  
996 996  
997 997   [[image:image-20220610172924-6.png||height="601" width="860"]]
... ... @@ -1015,16 +1015,19 @@
1015 1015  (((
1016 1016  Format: Command Code (0x01) followed by 3 bytes time value.
1017 1017  
1035 +(((
1018 1018  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
1037 +)))
1019 1019  
1020 1020  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
1021 1021  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1022 1022  )))
1042 +)))
1023 1023  
1024 1024  
1025 -
1026 -)))
1027 1027  
1046 +
1047 +
1028 1028  == 3.3  Set Interrupt Mode ==
1029 1029  
1030 1030  Feature, Set Interrupt mode for GPIO_EXIT.
... ... @@ -1038,7 +1038,9 @@
1038 1038  
1039 1039  Format: Command Code (0x06) followed by 3 bytes.
1040 1040  
1061 +(((
1041 1041  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1063 +)))
1042 1042  
1043 1043  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1044 1044  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1655254599445-662.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +117.0 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0