<
From version < 147.4 >
edited by Xiaoling
on 2022/06/10 17:40
To version < 147.2 >
edited by Xiaoling
on 2022/06/10 17:34
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -977,44 +977,106 @@
977 977  
978 978  
979 979  (((
980 -(% style="color:#037691" %)**Downlink Command: 0x01**
980 +(% style="color:#037691" %)**Downlink Command: 0x06**
981 981  )))
982 982  
983 983  (((
984 +Format: Command Code (0x06) followed by 3 bytes.
985 +)))
986 +
984 984  (((
985 -Format: Command Code (0x01) followed by 3 bytes time value.
988 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
989 +)))
986 986  
987 -If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
988 -
989 -* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
990 -* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
991 +* (((
992 +Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
991 991  )))
994 +* (((
995 +Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
996 +)))
992 992  
998 +== 3.3  Get Firmware Version Info ==
993 993  
994 -
1000 +Feature: use downlink to get firmware version.
1001 +
1002 +(% style="color:#037691" %)**Downlink Command: 0x26**
1003 +
1004 +[[image:image-20220607171917-10.png]]
1005 +
1006 +* Reply to the confirmation package: 26 01
1007 +* Reply to non-confirmed packet: 26 00
1008 +
1009 +Device will send an uplink after got this downlink command. With below payload:
1010 +
1011 +Configures info payload:
1012 +
1013 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
1014 +|=(((
1015 +**Size(bytes)**
1016 +)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
1017 +|**Value**|Software Type|(((
1018 +Frequency
1019 +
1020 +Band
1021 +)))|Sub-band|(((
1022 +Firmware
1023 +
1024 +Version
1025 +)))|Sensor Type|Reserve|(((
1026 +[[Message Type>>||anchor="H2.3.7A0MessageType"]]
1027 +Always 0x02
995 995  )))
996 996  
997 -== 3.3  Set Interrupt Mode ==
1030 +**Software Type**: Always 0x03 for LLDS12
998 998  
999 -Feature, Set Interrupt mode for GPIO_EXIT.
1000 1000  
1033 +**Frequency Band**:
1001 1001  
1002 -(% style="color:#037691" %)**Downlink Command: AT+INTMOD**
1035 +*0x01: EU868
1003 1003  
1004 -[[image:image-20220610105907-1.png]]
1037 +*0x02: US915
1005 1005  
1039 +*0x03: IN865
1006 1006  
1007 -**Downlink Command: 0x06**
1041 +*0x04: AU915
1008 1008  
1009 -Format: Command Code (0x06) followed by 3 bytes.
1043 +*0x05: KZ865
1010 1010  
1011 -This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1045 +*0x06: RU864
1012 1012  
1013 -* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
1014 -* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1047 +*0x07: AS923
1015 1015  
1049 +*0x08: AS923-1
1016 1016  
1051 +*0x09: AS923-2
1017 1017  
1053 +*0xa0: AS923-3
1054 +
1055 +
1056 +**Sub-Band**: value 0x00 ~~ 0x08
1057 +
1058 +
1059 +**Firmware Version**: 0x0100, Means: v1.0.0 version
1060 +
1061 +
1062 +**Sensor Type**:
1063 +
1064 +0x01: LSE01
1065 +
1066 +0x02: LDDS75
1067 +
1068 +0x03: LDDS20
1069 +
1070 +0x04: LLMS01
1071 +
1072 +0x05: LSPH01
1073 +
1074 +0x06: LSNPK01
1075 +
1076 +0x07: LLDS12
1077 +
1078 +
1079 +
1018 1018  = 5.  Battery & How to replace =
1019 1019  
1020 1020  == 5.1  Battery Type ==
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0