Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -63,9 +63,6 @@
63	63	* Downlink to change configure
64	64	* 8500mAh Battery for long term use
65	65
66		-
67		-
68		-
69	69	== 1.3  Probe Specification ==
70	70
71	71	* Storage temperature ：-20℃~~75℃
...	...	@@ -877,81 +877,57 @@
877	877	* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
878	878	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
879	879
	877	+
	878	+
880	880	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
881	881
882	882	(((
883		-(((
884	884	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
885	885	)))
886		-)))
887	887
888	888	* (((
889		-(((
890	890	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
891	891	)))
892		-)))
893	893	* (((
894		-(((
895	895	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
896	896	)))
897		-)))
898	898
899	899	(((
900		-(((
901	901
902		-)))
903	903
904		-(((
905	905	There are two kinds of commands to configure LLDS12, they are:
906	906	)))
907		-)))
908	908
909	909	* (((
910		-(((
911	911	(% style="color:#4f81bd" %)** General Commands**.
912	912	)))
913		-)))
914	914
915	915	(((
916		-(((
917	917	These commands are to configure:
918	918	)))
919		-)))
920	920
921	921	* (((
922		-(((
923	923	General system settings like: uplink interval.
924	924	)))
925		-)))
926	926	* (((
927		-(((
928	928	LoRaWAN protocol & radio related command.
929	929	)))
930		-)))
931	931
932	932	(((
933		-(((
934	934	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
935	935	)))
936		-)))
937	937
938	938	(((
939		-(((
940	940
941	941	)))
942		-)))
943	943
944	944	* (((
945		-(((
946	946	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
947	947	)))
948		-)))
949	949
950	950	(((
951		-(((
952	952	These commands only valid for LLDS12, as below:
953	953	)))
954		-)))
955	955
956	956
957	957
...	...	@@ -964,6 +964,7 @@
964	964	[[image:image-20220607171554-8.png]]
965	965
966	966
	940	+
967	967	(((
968	968	(% style="color:#037691" %)**Downlink Command: 0x01**
969	969	)))
...	...	@@ -986,7 +986,6 @@
986	986
987	987	)))
988	988
989		-
990	990	== 4.2  Set Interrupt Mode ==
991	991
992	992	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1015,7 +1015,6 @@
1015	1015	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1016	1016	)))
1017	1017
1018		-
1019	1019	== 4.3  Get Firmware Version Info ==
1020	1020
1021	1021	Feature: use downlink to get firmware version.
...	...	@@ -1212,14 +1212,10 @@
1212	1212
1213	1213
1214	1214	(((
1215		-(((
1216	1216	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1217		-)))
1218	1218
1219		-(((
1220	1220	LLDS12 will output system info once power on as below:
1221	1221	)))
1222		-)))
1223	1223
1224	1224
1225	1225	[[image:1654593712276-618.png]]
...	...	@@ -1240,9 +1240,7 @@
1240	1240	== 8.1  AT Commands input doesn’t work ==
1241	1241
1242	1242
1243		-(((
1244	1244	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1245		-)))
1246	1246
1247	1247
1248	1248	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==