Last modified by Bei Jinggeng on 2024/03/30 17:55
<
From version < 26.7 >
edited by Xiaoling
on 2022/06/07 15:08
To version < 23.5 >
edited by Xiaoling
on 2022/06/07 14:40
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -55,6 +55,7 @@
55 55  * IP68 rate for the Sensor Probe
56 56  * 8500mAh Battery for long term use
57 57  
58 +
58 58  == 1.3 Probe Specification ==
59 59  
60 60  
... ... @@ -75,10 +75,12 @@
75 75  * IP68 Protection
76 76  * Length: 3.5 meters
77 77  
79 +
78 78  == 1.4 ​Applications ==
79 79  
80 80  * Smart Agriculture
81 81  
84 +
82 82  == 1.5 Pin mapping and power on ==
83 83  
84 84  [[image:1654580482666-473.png]]
... ... @@ -265,6 +265,7 @@
265 265  |0x02|Reply configures info|[[Configure Info Payload>>||anchor="H3.4GetFirmwareVersionInfo"]]
266 266  |0x03|Reply Calibration Info|[[Calibration Payload>>||anchor="H2.7Calibration"]]
267 267  
271 +
268 268  === 2.3.7 Decode payload in The Things Network ===
269 269  
270 270  While using TTN network, you can add the payload format to decode the payload.
... ... @@ -338,76 +338,95 @@
338 338  
339 339  
340 340  
341 -== 2.6 Installation and Maintain ==
342 342  
343 -=== 2.6.1 Before measurement ===
344 344  
345 -(((
347 +1.
348 +11. Installation and Maintain
349 +111. Before measurement
350 +
346 346  If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
347 -)))
348 348  
349 349  
354 +1.
355 +11.
356 +111. Measurement
350 350  
351 -=== 2.6.2 Measurement ===
358 +**Measurement the soil surface**
352 352  
353 353  
354 -(% style="color:#4f81bd" %)**Measurement the soil surface:**
361 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] Choose the proper measuring position. Split the surface soil according to the measured deep.
355 355  
356 -[[image:1654584128046-287.png]]
357 357  
358 -Choose the proper measuring position. Split the surface soil according to the measured deep.
359 -
360 360  Put pure water, or rainwater to make the soil of measurement point to moist mud. Remove rocks or hard things.
361 361  
366 +
362 362  Slowly insert the probe to the measure point. Don’t use large force which will break the probe. Make sure not shake when inserting.
363 363  
369 +
364 364  Put soil over the probe after insert. And start to measure.
365 365  
366 366  
367 -(% style="color:#4f81bd" %)**Measurement inside soil:**
373 +**Measurement inside soil**
368 368  
375 +
376 +
369 369  Dig a hole with diameter > 20CM.
370 370  
379 +
371 371  Insert the probe inside, method like measure the surface.
372 372  
373 373  
383 +1.
384 +11.
385 +111. Maintain Probe
386 +1111. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
387 +1111. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
388 +1111. Probe reference electrode is also no strong, need to avoid strong force or hitting.
389 +1111. User should keep reference electrode wet while not use.
390 +1111. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
391 +1111. The probe is IP68 can be put in water.
374 374  
375 -=== 2.6.3 Maintain Probe ===
393 +1.
394 +11. Calibration
376 376  
377 -1. (((
378 -pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
379 -)))
380 -1. (((
381 -After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
382 -)))
383 -1. (((
384 -Probe reference electrode is also no strong, need to avoid strong force or hitting.
385 -)))
386 -1. (((
387 -User should keep reference electrode wet while not use.
388 -)))
389 -1. (((
390 -Avoid the probes to touch oily matter. Which will cause issue in accuracy.
391 -)))
392 -1. (((
393 -The probe is IP68 can be put in water.
396 +User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
394 394  
395 395  
396 -
397 -)))
399 +**After stable, user can use below command to calibrate.**
398 398  
399 -== 2.7 Calibration ==
400 400  
401 -User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
402 +|**pH buffer solution**|**AT Command to calibrate**|**Downlink Command**|**Read Cal Value**
403 +|**4.00**|**AT+PHCAL=4**|(((
404 +**0x13 04**
402 402  
403 -After stable, user can use below command to calibrate.
406 +**Reply with Calibrate payload**
407 +)))|(((
408 +**AT+PHCAL=?**
404 404  
405 -[[image:image-20220607144936-3.png]]
410 +**Example 41,61,91**
411 +)))
412 +|**6.86**|**AT+PHCAL=6**|(((
413 +**0x13 06**
406 406  
415 +**Reply with Calibrate payload**
416 +)))|**AT+PHCAL=?**
417 +|**9.18**|**AT+PHCAL=9**|(((
418 +**0x13 09**
407 407  
408 -(% style="color:#037691" %)**Calibration Payload**
420 +**Reply with Calibrate payload**
421 +)))|**AT+PHCAL=?**
422 +|**Factory Default**|**AT+PHCAL=15**|(((
423 +**0x13 15**
409 409  
410 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
425 +**Reply with Calibrate payload**
426 +)))|(((
427 +**AT+PHCAL=?**
428 +
429 +**Example 151**
430 +)))
431 +
432 +Calibration Payload
433 +
411 411  |(((
412 412  **Size**
413 413  
... ... @@ -422,29 +422,33 @@
422 422  
423 423  Calibrate value
424 424  )))|Reserve|(((
425 -[[Message Type>>||anchor="H2.3.6MessageType"]]
448 +[[Message>>path:#Message_Type]]
426 426  
450 +[[Type>>path:#Message_Type]]
451 +
427 427  Always 0x03
428 428  )))
429 429  
430 430  User can also send 0x14 downlink command to poll the current calibration payload.
431 431  
432 -[[image:image-20220607145603-4.png]]
433 433  
458 +|**Downlink Control Type**|**FPort**|**Type Code**|**Downlink payload size(bytes)**
459 +|Get Calibration Version Info|Any|14|2
460 +
434 434  * Reply to the confirmation package: 14 01
435 435  * Reply to non-confirmed packet: 14 00
436 436  
437 -== 2.8 Frequency Plans ==
464 +1.
465 +11. Frequency Plans
438 438  
439 -(((
440 440  The LSPH01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
441 -)))
442 442  
469 +1.
470 +11.
471 +111. EU863-870 (EU868)
443 443  
444 -=== 2.8.1 EU863-870 (EU868) ===
473 +Uplink:
445 445  
446 -(% style="color:blue" %)**Uplink:**
447 -
448 448  868.1 - SF7BW125 to SF12BW125
449 449  
450 450  868.3 - SF7BW125 to SF12BW125 and SF7BW250
... ... @@ -464,7 +464,7 @@
464 464  868.8 - FSK
465 465  
466 466  
467 -(% style="color:blue" %)**Downlink:**
494 +Downlink:
468 468  
469 469  Uplink channels 1-9 (RX1)
470 470  
... ... @@ -471,30 +471,28 @@
471 471  869.525 - SF9BW125 (RX2 downlink only)
472 472  
473 473  
501 +1.
502 +11.
503 +111. US902-928(US915)
474 474  
475 -=== 2.8.2 US902-928(US915) ===
476 -
477 -(((
478 478  Used in USA, Canada and South America. Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
479 -)))
480 480  
481 -(((
507 +
482 482  To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
483 -)))
484 484  
485 -(((
510 +
486 486  After Join success, the end node will switch to the correct sub band by:
487 -)))
488 488  
489 489  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
490 490  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
491 491  
516 +1.
517 +11.
518 +111. CN470-510 (CN470)
492 492  
493 -=== 2.8.3 CN470-510 (CN470) ===
494 -
495 495  Used in China, Default use CHE=1
496 496  
497 -(% style="color:blue" %)**Uplink:**
522 +Uplink:
498 498  
499 499  486.3 - SF7BW125 to SF12BW125
500 500  
... ... @@ -513,7 +513,7 @@
513 513  487.7 - SF7BW125 to SF12BW125
514 514  
515 515  
516 -(% style="color:blue" %)**Downlink:**
541 +Downlink:
517 517  
518 518  506.7 - SF7BW125 to SF12BW125
519 519  
... ... @@ -534,45 +534,38 @@
534 534  505.3 - SF12BW125 (RX2 downlink only)
535 535  
536 536  
562 +1.
563 +11.
564 +111. AU915-928(AU915)
537 537  
538 -=== 2.8.4 AU915-928(AU915) ===
539 -
540 -(((
541 541  Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
542 -)))
543 543  
544 -(((
568 +
545 545  To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
546 -)))
547 547  
548 -(((
549 -
550 -)))
551 551  
552 -(((
553 553  After Join success, the end node will switch to the correct sub band by:
554 -)))
555 555  
556 556  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
557 557  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
558 558  
577 +1.
578 +11.
579 +111. AS920-923 & AS923-925 (AS923)
559 559  
560 -=== 2.8.5 AS920-923 & AS923-925 (AS923) ===
581 +**Default Uplink channel:**
561 561  
562 -(% style="color:blue" %)**Default Uplink channel:**
563 -
564 564  923.2 - SF7BW125 to SF10BW125
565 565  
566 566  923.4 - SF7BW125 to SF10BW125
567 567  
568 568  
569 -(% style="color:blue" %)**Additional Uplink Channel**:
588 +**Additional Uplink Channel**:
570 570  
571 571  (OTAA mode, channel added by JoinAccept message)
572 572  
592 +**AS920~~AS923 for Japan, Malaysia, Singapore**:
573 573  
574 -(% style="color:blue" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
575 -
576 576  922.2 - SF7BW125 to SF10BW125
577 577  
578 578  922.4 - SF7BW125 to SF10BW125
... ... @@ -586,7 +586,7 @@
586 586  922.0 - SF7BW125 to SF10BW125
587 587  
588 588  
589 -(% style="color:blue" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
607 +**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
590 590  
591 591  923.6 - SF7BW125 to SF10BW125
592 592  
... ... @@ -601,18 +601,20 @@
601 601  924.6 - SF7BW125 to SF10BW125
602 602  
603 603  
604 -(% style="color:blue" %)**Downlink:**
605 605  
623 +**Downlink:**
624 +
606 606  Uplink channels 1-8 (RX1)
607 607  
608 608  923.2 - SF10BW125 (RX2)
609 609  
610 610  
630 +1.
631 +11.
632 +111. KR920-923 (KR920)
611 611  
612 -=== 2.8.6 KR920-923 (KR920) ===
634 +Default channel:
613 613  
614 -(% style="color:blue" %)**Default channel:**
615 -
616 616  922.1 - SF7BW125 to SF12BW125
617 617  
618 618  922.3 - SF7BW125 to SF12BW125
... ... @@ -620,7 +620,7 @@
620 620  922.5 - SF7BW125 to SF12BW125
621 621  
622 622  
623 -(% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
643 +Uplink: (OTAA mode, channel added by JoinAccept message)
624 624  
625 625  922.1 - SF7BW125 to SF12BW125
626 626  
... ... @@ -637,7 +637,7 @@
637 637  923.3 - SF7BW125 to SF12BW125
638 638  
639 639  
640 -(% style="color:blue" %)**Downlink:**
660 +Downlink:
641 641  
642 642  Uplink channels 1-7(RX1)
643 643  
... ... @@ -644,9 +644,11 @@
644 644  921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
645 645  
646 646  
647 -=== 2.8.7 IN865-867 (IN865) ===
667 +1.
668 +11.
669 +111. IN865-867 (IN865)
648 648  
649 -(% style="color:blue" %)**Uplink:**
671 +Uplink:
650 650  
651 651  865.0625 - SF7BW125 to SF12BW125
652 652  
... ... @@ -655,7 +655,7 @@
655 655  865.9850 - SF7BW125 to SF12BW125
656 656  
657 657  
658 -(% style="color:blue" %)**Downlink:**
680 +Downlink:
659 659  
660 660  Uplink channels 1-3 (RX1)
661 661  
... ... @@ -662,9 +662,9 @@
662 662  866.550 - SF10BW125 (RX2)
663 663  
664 664  
687 +1.
688 +11. LED Indicator
665 665  
666 -== 2.9 LED Indicator ==
667 -
668 668  The LSPH01 has an internal LED which is to show the status of different state.
669 669  
670 670  
1654584128046-287.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -345.3 KB
Content
image-20220607144936-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -23.6 KB
Content
image-20220607145603-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -5.8 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0