Changes for page LHT65N -- Manual do sensor de temperatura e umidade LoRaWAN

Last modified by Xiaoling on 2023/07/18 10:12

From 204.1 to 203.1 From 210.1 to 209.1

From version 209.1

edited by Bei Jinggeng
on 2022/10/18 10:47

Change comment: There is no comment for this version

To version 204.1

edited by Edwin Chen
on 2022/10/08 15:03

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Bei
++XWiki.Edwin

Content

@@ -197,7 +197,7 @@
--== 2.4 Uplink Payload   ( Fport~=2) ==
++== 2.4 Uplink Payload ==
  (((
@@ -276,14 +276,18 @@
  * The 7th byte (EXT #): defines the external sensor model.
  * The 8(% _msthash="734578" _msttexthash="21372" _mstvisible="4" %)^^th^^(%%) ~~ 11(% _msthash="734579" _msttexthash="21372" _mstvisible="4" %)^^th^^(%%) byte: the value for external sensor value. The definition is based on external sensor type. (If EXT=0, there won't be these four bytes.)
++
  === 2.4.1 Decoder in TTN V3 ===
  When the uplink payload arrives TTNv3, it shows HEX format and not friendly to read. We can add LHT65N decoder in TTNv3 for friendly reading.
--Below is the position to put the decoder and LHT65N decoder can be download from here: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
++Below is the position to put the decoder and LHT65N decoder can be download from here:
++[[https:~~/~~/www.dropbox.com/sh/r2i3zlhsyrpavla/AAB1sZw3mdT0K7XjpHCITt13a?dl=0 >>https://www.dropbox.com/sh/r2i3zlhsyrpavla/AAB1sZw3mdT0K7XjpHCITt13a?dl=0||_msthash="315253" _msttexthash="3509064" _mstvisible="2"]]
++
++
  [[image:image-20220522234118-10.png||_mstalt="451464" _mstvisible="3" height="353" width="729"]]
@@ -305,6 +305,7 @@
  * BAT status=(0Xcba4>>14)&0xFF=11(B)，very good
  * Battery Voltage =0xCBF6&0x3FFF=0x0BA4=2980mV
++
  === 2.4.3 Built-in Temperature ===
@@ -316,6 +316,7 @@
  * Temperature:  (0xF5C6-65536)/100=-26.18℃
++
  === 2.4.4 Built-in Humidity ===
@@ -323,6 +323,7 @@
  * Humidity:    0x025C/10=60.4%
++
  === 2.4.5 Ext # ===
@@ -480,6 +480,7 @@
  * (% style="color:blue" %)**Sync time OK**: (%%)          1: Set time ok，0: N/A. After time SYNC request is sent, LHT65N will set this bit to 0 until got the time stamp from the application server.
  * (% style="color:blue" %)**Unix Time Request**:(%%)  1: Request server downlink Unix time, 0 : N/A. In this mode, LHT65N will set this bit to 1 every 10 days to request a time SYNC. (AT+SYNCMOD to set this)
++
  ==== 2.4.6.3 Ext~=6, ADC Sensor (use with E2 Cable) ====
@@ -994,9 +994,9 @@
  (((
  [[image:image-20221006192726-1.png||height="112" width="754"]]
--(% class="mark" %)**No ACK Message**(%%): 1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for [[PNACKMD=1>>||anchor="H4.13AutoSendNone-ACKmessages"]] feature)
++(% class="mark" %)No ACK Message(%%): 1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for [[PNACKMD=1>>||anchor="H4.13AutoSendNone-ACKmessages"]] feature)
--(% class="mark" %)**Poll Message Flag**(%%): 1: This message is a poll message reply.
++(% class="mark" %)Poll Message Flag(%%): 1: This message is a poll message reply.
  )))
@@ -1047,7 +1047,7 @@
  (((
  (% _msthash="736725" _msttexthash="1065532" _mstvisible="3" %)
  (((
--**a) DR0:** max is 11 bytes so one entry of data
++a) DR0: max is 11 bytes so one entry of data
  )))
  )))
  )))
@@ -1058,7 +1058,7 @@
  (((
  (% _msthash="736726" _msttexthash="3265665" _mstvisible="3" %)
  (((
--**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
++b) DR1: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
  )))
  )))
  )))
@@ -1069,7 +1069,7 @@
  (((
  (% _msthash="736727" _msttexthash="1454115" _mstvisible="3" style="text-align: left;" %)
  (((
--**c) DR2:** total payload includes 11 entries of data
++c) DR2: total payload includes 11 entries of data
  )))
  )))
  )))
@@ -1080,7 +1080,7 @@
  (((
  (% _msthash="736728" _msttexthash="1483924" _mstvisible="3" style="text-align: left;" %)
  (((
--**d) DR3: **total payload includes 22 entries of data.
++d) DR3: total payload includes 22 entries of data.
  )))
  )))
  )))
@@ -1091,7 +1091,7 @@
  (((
  (% _msthash="736729" _msttexthash="5848349" _mstvisible="3" style="text-align: left;" %)
  (((
--If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0
++If devise doesn’t have any data in the polling time. Device will uplink 11 bytes of 0
  )))
  )))
  )))
@@ -1192,37 +1192,17 @@
  (((
  (% style="color:red" %)**Note: alarm mode adds a little power consumption, and we recommend extending the normal read time when this feature is enabled.**
--=== **2.7.1 ALARM MODE ( Since v1.3.1 firmware)** ===
--
--(((
--(% class="box infomessage" %)
--(((
--**AT+WMOD=3,**:              Enable/disable alarm mode. (0: Disabled, 1: Enabled Temperature Alarm for onboard temperature sensor)
--
--**AT+CITEMP=1**:             The interval between checking the alarm temperature. (In minutes)
--
--**AT+ARTEMP**:                 Gets or sets the alarm range of the internal temperature sensor
--
--**AT+ARTEMP=？ **:          Gets the alarm range of the internal temperature sensor(% _mstvisible="3" style="display:none" %)
--
--**AT+ARTEMP=45,105**:   Set the internal temperature sensor alarm range from 45 to 105.
--
--**AT+LEDALARM=1** :       Enable LED visual Alarm.
--)))
--)))
--
--
  )))
  (((
--=== **2.7.2 ALARM MODE ( Before v1.3.1 firmware)** ===
++**AT COMMAND FOR ALARM MODE:**
  )))
  (% _mstvisible="1" class="box infomessage" %)
  (((
  (((
--**AT+WMOD=1**:              Enable/disable alarm mode. (0: Disabled, 1: Enabled Temperature Alarm for onboard temperature sensor)
++**AT+WMOD=1**:              Enable/disable alarm mode. (0: Disabled, 1: Enabled)
  )))
  (((
@@ -1272,6 +1272,7 @@
  * RED LED when external sensor is not connected
  * For each success downlink, the PURPLE LED will blink once
++
  == 2.9 installation ==
@@ -1329,6 +1329,7 @@
  * Operating Range: -40 ~~ 125 °C
  * Working voltage 2.35v ~~ 5v
++
  = 4. Configure LHT65N via AT command or LoRaWAN downlink =
@@ -1398,6 +1398,7 @@
  * **Example 2**: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
++
  == 4.2 Set External Sensor Mode ==
@@ -1421,6 +1421,7 @@
  * 0xA20702003c: Same as AT+SETCNT=60
++
  == 4.3 Enable/Disable uplink Temperature probe ID ==
@@ -1451,6 +1451,7 @@
  * **0xA800**     **~-~->** AT+PID=0
  * **0xA801**     **~-~->** AT+PID=1
++
  == 4.4 Set Password ==
@@ -1502,6 +1502,7 @@
  * There is no downlink command to set to Sleep mode.
++
  == 4.7 Set system time ==
@@ -1557,7 +1557,7 @@
  (% _msthash="315257" _msttexthash="298038" style="color:#4f81bd" %)**Downlink Command:**
--**0x29 0A**   ~/~/ Same as AT+SYNCTDC=0x0A
++**0x29 0A** ~/~/ Same as AT+SYNCTDC=0x0A
@@ -1608,8 +1608,9 @@
  (% style="color:#4f81bd" %)**Downlink Command: 0xA3**
--* Example: 0xA301     ~/~/  Same as AT+CLRDTA
++* Example: 0xA301   ~/~/Same as AT+CLRDTA
++
  == 4.13 Auto Send None-ACK messages ==
@@ -1628,57 +1628,9 @@
  (% style="color:#4f81bd" %)**Downlink Command: 0x34**
--* Example: 0x3401   ~/~/  Same as AT+PNACKMD=1
++* Example: 0x3401   ~/~/Same as AT+PNACKMD=1
--== 4.14 Modified ATWOOD command for external sensor TMP117 or DS18B20 temperature alarm ==
--
--Feature: Set internal and external temperature sensor alarms.
--
--(% border="1" style="background-color:#ffffcc; color:green; width:450px" %)
--|(%%)(% _msthash="1231737" _msttexthash="251862" _mstvisible="6" %)**Command Example**|(%%)(% _msthash="1231738" _msttexthash="116025" _mstvisible="6" %)**Function**|(%%)(% _msthash="1231739" _msttexthash="116831" _mstvisible="6" %)**Response**
--|(%%)(% style="color:#037691" %)AT+WMOD=parameter1,parameter2,parameter3,parameter4|Set internal and external temperature sensor alarms|OK
--
--(% style="color:#037691" %)**AT+WMOD=parameter1,parameter2,parameter3,parameter4**
--
--(% style="color:#037691" %)**Parameter 1**(%%):  Alarm mode:
--
--0): Cancel
--
--1): Threshold alarm
--
--2): Fluctuation alarm
--
--
--(% style="color:#037691" %)** Parameter 2**(%%):  Sampling time. Unit: seconds, up to 255 seconds.
--
--(% style="color:red" %)**Note: When the collection time is less than 60 seconds and always exceeds the set alarm threshold, the sending interval will not be the collection time, but will be sent every 60 seconds.**
--
--
--(% style="color:#037691" %) **Parameter 3 and parameter 4:**
--
--1):  If Alarm Mode is set to 1: Parameter 3 and parameter 4 are valid, as before, they represent low temperature and high temperature.
--
--Such as AT+WMOD=1,60,45,105, it means high and low temperature alarm.
--
--
--2):  If Alarm Mode is set to 2: Parameter 3 is valid, which represents the difference between the currently collected temperature and the last uploaded temperature.
--
--Such as AT+WMOD=2,10,2,it means that it is a fluctuation alarm.
--
--If the difference between the current collected temperature and the last Uplin is ±2 degrees, the alarm will be issued.
--
--
--(% style="color:#4f81bd" %)**Downlink Command: 0xA5**
--
--0xA5 00 ~-~- AT+WMOD=0.
--
--0xA5 01 0A 11 94 29 04 ~-~- AT+WMOD=1,10,45,105  (AT+WMOD = second byte, third byte, fourth and fifth bytes divided by 100, sixth and seventh bytes divided by 100 )
--
--0xA5 02 0A 02 ~-~- AT+WMOD=2,10,2  (AT+WMOD = second byte, third byte, fourth byte)
--
--0xA5 FF ~-~- After the device receives it, upload the current alarm configuration (FPORT=8). Such as 01 0A 11 94 29 04 or 02 0A 02.
--
  = 5. Battery & How to replace =
@@ -1748,6 +1748,7 @@
  * (% style="background-color:yellow" %)**USB to TTL GND <~-~->GND**
  * (% style="background-color:yellow" %)**USB to TTL RXD <~-~-> D+**
  * (% style="background-color:yellow" %)**USB to TTL TXD <~-~-> A11**
++* (% style="background-color:yellow" %)**USB to TTL 3.3V <~-~-> D-**
  (((
  In PC, User needs to set serial tool(such as [[**putty**>>https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to (% style="color:green" %)**9600**(%%) to access to access serial console for LHT65N. The AT commands are disable by default and need to enter password (default:(% style="color:green" %)**123456**) (%%)to active it. Timeout to input AT Command is 5 min, after 5-minute, user need to input password again. User can use AT+DISAT command to disable AT command before timeout.
@@ -2147,6 +2147,7 @@
  * (% style="color:red" %)**E3**(%%): External Temperature Probe
++
  = 8. Packing Info =
@@ -2160,11 +2160,13 @@
  * Device Size:  10 x 10 x 3.5 cm
  * Device Weight: 120.5g
++
  = 9. Reference material =
  * [[Datasheet, photos, decoder, firmware>>https://www.dropbox.com/sh/una19zsni308dme/AACOKp6J2RF5TMlKWT5zU3RTa?dl=0||_msthash="504975" _msttexthash="51420512"]]
++
  = 10. FCC Warning =

Changes for page LHT65N -- Manual do sensor de temperatura e umidade LoRaWAN

Summary

Details

Applications

Navigation