Wiki source code of LSPH01-LoRaWAN Soil pH Sensor User Manual

Version 34.33 by Xiaoling on 2022/06/07 16:46

version	line-number	content
2.2	1	(% style="text-align:center" %)
	2	[[image:1654574317295-380.png\|\|height="621" width="576"]]
1.1	3
	4
	5
	6
	7
14.8	8	Contents:
1.1	9
14.8	10	{{toc/}}
1.1	11
	12
	13
	14
	15
	16
	17
	18
	19
14.8	20
	21
	22
3.2	23	= 1. Introduction =
2.2	24
3.2	25	== 1.1 What is LoRaWAN Soil pH Sensor ==
2.2	26
3.2	27	The Dragino LSPH01 is a (% style="color:#4f81bd" %)LoRaWAN Soil pH Sensor(%%) for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
2.2	28
3.2	29	LSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's (% style="color:#4f81bd" %)pH (%%)with high accuracy and stable value. The LSPH01 probe can be buried into soil for long time use.
2.2	30
	31	The LoRa wireless technology used in LSPH01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
	32
3.2	33	LSPH01 is powered by (% style="color:#4f81bd" %)8500mAh Li-SOCI2 battery(%%), it is designed for long term use up to 5 years.
2.2	34
3.2	35	Each LSPH01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
2.2	36
	37
3.2	38	[[image:1654580186518-415.png]]
2.2	39
	40
	41
3.2	42	== 1.2 Features ==
	43
2.2	44	* LoRaWAN 1.0.3 Class A
	45	* Ultra-low power consumption
	46	* Monitor soil pH with temperature compensation.
	47	* Monitor soil temperature
	48	* Monitor Battery Level
	49	* Support pH calibration by end user
	50	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	51	* AT Commands to change parameters
	52	* Uplink on periodically
	53	* Downlink to change configure
	54	* IP66 Waterproof Enclosure
	55	* IP68 rate for the Sensor Probe
	56	* 8500mAh Battery for long term use
	57
34.15	58
3.3	59	== 1.3 Probe Specification ==
2.2	60
	61
3.3	62	(% style="color:#4f81bd" %)Soil pH:
	63
	64	* Range: 3 ~~ 10 pH
	65	* Resolution: 0.01 pH
	66	* Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)
	67	* Temperature Compensation Range: 0 ~~ 50℃
2.2	68	* IP68 Protection
	69	* Length: 3.5 meters
	70
3.3	71	(% style="color:#4f81bd" %)Soil Temperature:
2.2	72
3.3	73	* Range -40℃～85℃
	74	* Resolution: 0.1℃
	75	* Accuracy: <±0.5℃(-10℃～40℃)，<±0.8℃ (others)
2.2	76	* IP68 Protection
	77	* Length: 3.5 meters
	78
3.3	79	== 1.4 Applications ==
	80
2.2	81	* Smart Agriculture
	82
3.3	83	== 1.5 Pin mapping and power on ==
	84
5.5	85	[[image:1654580482666-473.png]]
2.2	86
	87
	88
5.2	89	= 2. Configure LSPH01 to connect to LoRaWAN network =
2.2	90
5.5	91	== 2.1 How it works ==
2.2	92
5.3	93	(((
2.2	94	The LSPH01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSPH01. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
5.3	95	)))
2.2	96
5.3	97	(((
34.18	98	In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>\|\|anchor="H5.UseATCommand"]]to set the keys in the LSPH01.
5.3	99	)))
2.2	100
	101
5.3	102	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
2.2	103
6.3	104	(((
2.2	105	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
6.3	106	)))
2.2	107
6.3	108	(((
	109
	110	)))
2.2	111
6.3	112	(((
2.2	113	The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
6.3	114	)))
2.2	115
6.3	116	(((
23.5	117	(% style="color:blue" %)Step 1(%%): Create a device in TTN with the OTAA keys from LSPH01.
6.3	118	)))
2.2	119
6.3	120	(((
2.2	121	Each LSPH01 is shipped with a sticker with the default device EUI as below:
6.3	122	)))
2.2	123
	124
6.3	125	[[image:image-20220607135531-1.jpeg]]
2.2	126
	127
	128	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	129
	130
	131	Register the device
	132
9.2	133	[[image:1654581442672-605.png]]
2.2	134
	135
9.2	136
2.2	137	Add APP EUI and DEV EUI
	138
9.2	139	[[image:1654581465717-368.png]]
2.2	140
	141
	142
	143	Add APP EUI in the application
	144
9.2	145	[[image:1654581493871-516.png]]
2.2	146
	147
10.2	148
2.2	149	Add APP KEY
	150
10.2	151	[[image:1654581517630-991.png]]
2.2	152
	153
23.5	154	(% style="color:blue" %)Step 2(%%): Power on LSPH01
2.2	155
	156
	157	Put a Jumper on JP2 to power on the device. ( The Switch must be in FLASH position).
	158
11.2	159	[[image:image-20220607135918-2.png]]
2.2	160
	161
23.5	162	(% style="color:blue" %)Step 3(%%): The LSPH01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
2.2	163
12.2	164	[[image:1654581590132-631.png]]
2.2	165
	166
	167
13.2	168	== 2.3 Uplink Payload ==
2.2	169
3.2	170	LSPH01 will uplink payload via LoRaWAN with below payload format:
2.2	171
	172	Uplink payload includes in total 11 bytes.
	173
	174	Normal uplink payload:
	175
13.2	176	(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
2.2	177	\|(((
	178	Size
	179
	180	(bytes)
	181	)))\|2\|2\|2\|2\|1\|1\|1
14.5	182	\|Value\|[[BAT>>\|\|anchor="H2.3.1BatteryInfo"]]\|(((
14.6	183	[[Temperature>>\|\|anchor="H2.3.2DS18B20Temperaturesensor"]]
2.2	184
14.6	185	[[(Optional)>>\|\|anchor="H2.3.2DS18B20Temperaturesensor"]]
	186	)))\|[[Soil pH>>\|\|anchor="H2.3.3SoilpH"]]\|[[Soil Temperature>>\|\|anchor="H2.3.4SoilTemperature"]]\|(((
	187	[[Digital Interrupt (Optional)>>\|\|anchor="H2.3.5InterruptPin"]]
2.2	188	)))\|Reserve\|(((
14.6	189	[[Message Type>>\|\|anchor="H2.3.6MessageType"]]
2.2	190	)))
	191
13.2	192	[[image:1654581735133-458.png]]
2.2	193
	194
	195
13.2	196	=== 2.3.1 Battery Info ===
2.2	197
13.2	198
2.2	199	Check the battery voltage for LSPH01.
	200
	201	Ex1: 0x0B45 = 2885mV
	202
	203	Ex2: 0x0B49 = 2889mV
	204
	205
	206
13.2	207	=== 2.3.2 DS18B20 Temperature sensor ===
2.2	208
13.2	209	This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
2.2	210
13.2	211
2.2	212	Example:
	213
	214	If payload is: 0105H: (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
	215
	216	If payload is: FF3FH : (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
	217
	218
	219
13.3	220	=== 2.3.3 Soil pH ===
2.2	221
	222	Range: 0 ~~ 14 pH
	223
13.3	224	Example:
2.2	225
13.3	226	(% style="color:#037691" %) 0x02B7(H) = 695(D) = 6.95pH
2.2	227
	228
	229
13.3	230	=== 2.3.4 Soil Temperature ===
	231
2.2	232	Get Soil Temperature
	233
	234
	235	Example:
	236
13.3	237	If payload is: 0105H: (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
2.2	238
13.3	239	If payload is: FF3FH : (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
2.2	240
	241
	242
13.3	243	=== 2.3.5 Interrupt Pin ===
2.2	244
13.4	245	This data field shows if this packet is generated by interrupt or not. [[Click here>>\|\|anchor="H3.2SetInterruptMode"]] for the hardware and software set up.
2.2	246
	247
13.3	248	Example:
2.2	249
	250	0x00: Normal uplink packet.
	251
	252	0x01: Interrupt Uplink Packet.
	253
	254
	255
13.3	256	=== 2.3.6 Message Type ===
	257
2.2	258	For a normal uplink payload, the message type is always 0x01.
	259
	260	Valid Message Type:
	261
	262
13.4	263	(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
	264	\|Message Type Code\|Description\|Payload
34.21	265	\|0x01\|Normal Uplink\|[[Normal Uplink Payload>>\|\|anchor="H2.3200BUplinkPayload"]]
13.5	266	\|0x02\|Reply configures info\|[[Configure Info Payload>>\|\|anchor="H3.4GetFirmwareVersionInfo"]]
13.6	267	\|0x03\|Reply Calibration Info\|[[Calibration Payload>>\|\|anchor="H2.7Calibration"]]
2.2	268
34.22	269
13.6	270	=== 2.3.7 Decode payload in The Things Network ===
	271
2.2	272	While using TTN network, you can add the payload format to decode the payload.
	273
	274
14.2	275	[[image:1654582541848-906.png]]
2.2	276
14.2	277	(((
2.2	278	The payload decoder function for TTN is here:
14.2	279	)))
2.2	280
14.2	281	(((
2.2	282	LSPH01 TTN Payload Decoder: [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Decoder/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSNPK01/Decoder/]]
14.2	283	)))
2.2	284
	285
	286
14.3	287	== 2.4 Uplink Interval ==
	288
14.4	289	The LSPH01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome\|\|anchor="H4.1ChangeUplinkInterval"]]
2.2	290
	291
	292
16.2	293	== 2.5 Show Data in DataCake IoT Server ==
2.2	294
	295	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	296
	297
23.5	298	(% style="color:blue" %)Step 1(%%): Be sure that your device is programmed and properly connected to the network at this time.
2.2	299
23.5	300	(% style="color:blue" %)Step 2(%%): To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
2.2	301
	302
16.2	303	[[image:1654583683416-869.png]]
2.2	304
	305
16.2	306	[[image:1654583694084-878.png]]
2.2	307
	308
23.5	309	(% style="color:blue" %)Step 3(%%): Create an account or log in Datacake.
2.2	310
23.5	311	(% style="color:blue" %)Step 4(%%): Create LSPH01 product.
2.2	312
17.2	313	[[image:1654583711590-413.png]]
2.2	314
	315
	316
19.2	317	[[image:1654583732798-193.png]]
2.2	318
	319
19.2	320	[[image:1654583749683-259.png]]
2.2	321
	322
23.5	323	(% style="color:blue" %)Step 5(%%): add payload decode
2.2	324
	325	Download Datacake decoder from: [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Decoder/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSNPK01/Decoder/]]
	326
	327
23.2	328	[[image:1654583770974-935.png]]
2.2	329
23.2	330	[[image:1654583781517-146.png]]
2.2	331
	332
23.2	333	[[image:1654583791351-557.png]]
2.2	334
	335
	336	After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
	337
	338
23.2	339	[[image:1654583805491-713.png]]
2.2	340
	341
	342
24.2	343	== 2.6 Installation and Maintain ==
2.2	344
24.2	345	=== 2.6.1 Before measurement ===
	346
	347	(((
3.2	348	If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy.
24.2	349	)))
2.2	350
	351
	352
24.2	353	=== 2.6.2 Measurement ===
2.2	354
	355
24.2	356	(% style="color:#4f81bd" %)Measurement the soil surface:
2.2	357
24.2	358	[[image:1654584128046-287.png]]
2.2	359
24.2	360	Choose the proper measuring position. Split the surface soil according to the measured deep.
	361
2.2	362	Put pure water, or rainwater to make the soil of measurement point to moist mud. Remove rocks or hard things.
	363
	364	Slowly insert the probe to the measure point. Don’t use large force which will break the probe. Make sure not shake when inserting.
	365
	366	Put soil over the probe after insert. And start to measure.
	367
	368
24.2	369	(% style="color:#4f81bd" %)Measurement inside soil:
2.2	370
24.2	371	Dig a hole with diameter > 20CM.
2.2	372
24.2	373	Insert the probe inside, method like measure the surface.
2.2	374
	375
	376
24.2	377	=== 2.6.3 Maintain Probe ===
2.2	378
24.2	379	1. (((
	380	pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
	381	)))
	382	1. (((
	383	After long time use (3~~ 6 months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
	384	)))
	385	1. (((
	386	Probe reference electrode is also no strong, need to avoid strong force or hitting.
	387	)))
	388	1. (((
	389	User should keep reference electrode wet while not use.
	390	)))
	391	1. (((
	392	Avoid the probes to touch oily matter. Which will cause issue in accuracy.
	393	)))
	394	1. (((
	395	The probe is IP68 can be put in water.
2.2	396
	397
25.2	398
	399	)))
2.2	400
24.3	401	== 2.7 Calibration ==
24.2	402
2.2	403	User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
	404
26.2	405	After stable, user can use below command to calibrate.
2.2	406
25.2	407	[[image:image-20220607144936-3.png]]
2.2	408
	409
25.2	410	(% style="color:#037691" %)Calibration Payload
2.2	411
25.2	412	(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
2.2	413	\|(((
	414	Size
	415
	416	(bytes)
	417	)))\|1\|1\|1\|7\|1
	418	\|Value\|(((
	419	PH4
	420
	421	Calibrate value
	422	)))\|PH6.86 Calibrate value\|(((
	423	PH9.18
	424
	425	Calibrate value
	426	)))\|Reserve\|(((
25.3	427	[[Message Type>>\|\|anchor="H2.3.6MessageType"]]
	428
	429	Always 0x03
2.2	430	)))
	431
	432	User can also send 0x14 downlink command to poll the current calibration payload.
	433
26.2	434	[[image:image-20220607145603-4.png]]
2.2	435
	436	* Reply to the confirmation package: 14 01
	437	* Reply to non-confirmed packet: 14 00
	438
34.23	439
26.5	440	== 2.8 Frequency Plans ==
26.2	441
26.6	442	(((
2.2	443	The LSPH01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
26.6	444	)))
2.2	445
	446
26.5	447	=== 2.8.1 EU863-870 (EU868) ===
2.2	448
26.5	449	(% style="color:blue" %)Uplink:
	450
2.2	451	868.1 - SF7BW125 to SF12BW125
	452
	453	868.3 - SF7BW125 to SF12BW125 and SF7BW250
	454
	455	868.5 - SF7BW125 to SF12BW125
	456
	457	867.1 - SF7BW125 to SF12BW125
	458
	459	867.3 - SF7BW125 to SF12BW125
	460
	461	867.5 - SF7BW125 to SF12BW125
	462
	463	867.7 - SF7BW125 to SF12BW125
	464
	465	867.9 - SF7BW125 to SF12BW125
	466
	467	868.8 - FSK
	468
	469
26.5	470	(% style="color:blue" %)Downlink:
2.2	471
	472	Uplink channels 1-9 (RX1)
	473
	474	869.525 - SF9BW125 (RX2 downlink only)
	475
	476
	477
26.5	478	=== 2.8.2 US902-928(US915) ===
	479
	480	(((
2.2	481	Used in USA, Canada and South America. Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
26.5	482	)))
2.2	483
26.5	484	(((
2.2	485	To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
26.5	486	)))
2.2	487
26.5	488	(((
2.2	489	After Join success, the end node will switch to the correct sub band by:
26.5	490	)))
2.2	491
	492	* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
	493	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
	494
34.24	495
26.5	496	=== 2.8.3 CN470-510 (CN470) ===
	497
2.2	498	Used in China, Default use CHE=1
	499
26.5	500	(% style="color:blue" %)Uplink:
2.2	501
	502	486.3 - SF7BW125 to SF12BW125
	503
	504	486.5 - SF7BW125 to SF12BW125
	505
	506	486.7 - SF7BW125 to SF12BW125
	507
	508	486.9 - SF7BW125 to SF12BW125
	509
	510	487.1 - SF7BW125 to SF12BW125
	511
	512	487.3 - SF7BW125 to SF12BW125
	513
	514	487.5 - SF7BW125 to SF12BW125
	515
	516	487.7 - SF7BW125 to SF12BW125
	517
	518
26.5	519	(% style="color:blue" %)Downlink:
2.2	520
	521	506.7 - SF7BW125 to SF12BW125
	522
	523	506.9 - SF7BW125 to SF12BW125
	524
	525	507.1 - SF7BW125 to SF12BW125
	526
	527	507.3 - SF7BW125 to SF12BW125
	528
	529	507.5 - SF7BW125 to SF12BW125
	530
	531	507.7 - SF7BW125 to SF12BW125
	532
	533	507.9 - SF7BW125 to SF12BW125
	534
	535	508.1 - SF7BW125 to SF12BW125
	536
	537	505.3 - SF12BW125 (RX2 downlink only)
	538
	539
	540
26.5	541	=== 2.8.4 AU915-928(AU915) ===
	542
	543	(((
2.2	544	Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
26.5	545	)))
2.2	546
26.5	547	(((
2.2	548	To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
26.5	549	)))
2.2	550
26.5	551	(((
	552
	553	)))
2.2	554
26.5	555	(((
2.2	556	After Join success, the end node will switch to the correct sub band by:
26.5	557	)))
2.2	558
	559	* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
	560	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
	561
34.25	562
26.5	563	=== 2.8.5 AS920-923 & AS923-925 (AS923) ===
	564
26.7	565	(% style="color:blue" %)Default Uplink channel:
2.2	566
	567	923.2 - SF7BW125 to SF10BW125
	568
	569	923.4 - SF7BW125 to SF10BW125
	570
	571
26.7	572	(% style="color:blue" %)Additional Uplink Channel:
2.2	573
	574	(OTAA mode, channel added by JoinAccept message)
	575
	576
26.7	577	(% style="color:blue" %)AS920~~AS923 for Japan, Malaysia, Singapore:
	578
2.2	579	922.2 - SF7BW125 to SF10BW125
	580
	581	922.4 - SF7BW125 to SF10BW125
	582
	583	922.6 - SF7BW125 to SF10BW125
	584
	585	922.8 - SF7BW125 to SF10BW125
	586
	587	923.0 - SF7BW125 to SF10BW125
	588
	589	922.0 - SF7BW125 to SF10BW125
	590
	591
26.7	592	(% style="color:blue" %)AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam:
2.2	593
	594	923.6 - SF7BW125 to SF10BW125
	595
	596	923.8 - SF7BW125 to SF10BW125
	597
	598	924.0 - SF7BW125 to SF10BW125
	599
	600	924.2 - SF7BW125 to SF10BW125
	601
	602	924.4 - SF7BW125 to SF10BW125
	603
	604	924.6 - SF7BW125 to SF10BW125
	605
	606
26.7	607	(% style="color:blue" %)Downlink:
2.2	608
	609	Uplink channels 1-8 (RX1)
	610
	611	923.2 - SF10BW125 (RX2)
	612
	613
	614
26.7	615	=== 2.8.6 KR920-923 (KR920) ===
2.2	616
26.7	617	(% style="color:blue" %)Default channel:
	618
2.2	619	922.1 - SF7BW125 to SF12BW125
	620
	621	922.3 - SF7BW125 to SF12BW125
	622
	623	922.5 - SF7BW125 to SF12BW125
	624
	625
26.7	626	(% style="color:blue" %)Uplink: (OTAA mode, channel added by JoinAccept message)
2.2	627
	628	922.1 - SF7BW125 to SF12BW125
	629
	630	922.3 - SF7BW125 to SF12BW125
	631
	632	922.5 - SF7BW125 to SF12BW125
	633
	634	922.7 - SF7BW125 to SF12BW125
	635
	636	922.9 - SF7BW125 to SF12BW125
	637
	638	923.1 - SF7BW125 to SF12BW125
	639
	640	923.3 - SF7BW125 to SF12BW125
	641
	642
26.7	643	(% style="color:blue" %)Downlink:
2.2	644
	645	Uplink channels 1-7(RX1)
	646
	647	921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
	648
	649
26.7	650	=== 2.8.7 IN865-867 (IN865) ===
2.2	651
26.7	652	(% style="color:blue" %)Uplink:
2.2	653
	654	865.0625 - SF7BW125 to SF12BW125
	655
	656	865.4025 - SF7BW125 to SF12BW125
	657
	658	865.9850 - SF7BW125 to SF12BW125
	659
	660
26.7	661	(% style="color:blue" %)Downlink:
2.2	662
	663	Uplink channels 1-3 (RX1)
	664
	665	866.550 - SF10BW125 (RX2)
	666
	667
	668
26.7	669	== 2.9 LED Indicator ==
	670
2.2	671	The LSPH01 has an internal LED which is to show the status of different state.
	672
	673	* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
	674	* Blink once when device transmit a packet.
	675
34.9	676
26.9	677	== 2.10 Firmware Change Log ==
2.2	678
26.15	679
2.2	680	Firmware download link:
	681
	682	[[http:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
	683
	684
26.14	685	Firmware Upgrade Method: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
2.2	686
	687
	688
26.16	689	= 3. Configure LSPH01 via AT Command or LoRaWAN Downlink =
2.2	690
	691	Use can configure LSPH01 via AT Command or LoRaWAN Downlink.
	692
26.17	693	* AT Command Connection: See [[FAQ>>\|\|anchor="H6.FAQ"]].
	694	* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
2.2	695
	696	There are two kinds of commands to configure LSPH01, they are:
	697
27.2	698	* (% style="color:#4f81bd" %) General Commands.
2.2	699
	700	These commands are to configure:
	701
	702	* General system settings like: uplink interval.
	703	* LoRaWAN protocol & radio related command.
	704
26.17	705	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:[[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
2.2	706
	707
27.2	708	* (% style="color:#4f81bd" %) Commands special design for LSPH01
2.2	709
	710	These commands only valid for LSPH01, as below:
	711
	712
	713
27.2	714	== 3.1 Set Transmit Interval Time ==
	715
2.2	716	Feature: Change LoRaWAN End Node Transmit Interval.
	717
27.2	718	(% style="color:#037691" %)AT Command: AT+TDC
2.2	719
27.2	720
	721	(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:710px" %)
	722	\|(% style="width:154px" %)Command Example\|(% style="width:223px" %)Function\|(% style="width:330px" %)Response
	723	\|(% style="width:154px" %)AT+TDC=?\|(% style="width:223px" %)Show current transmit Interval\|(% style="width:330px" %)(((
2.2	724	30000
	725
	726	OK
	727
	728	the interval is 30000ms = 30s
	729	)))
27.2	730	\|(% style="width:154px" %)AT+TDC=60000\|(% style="width:223px" %)Set Transmit Interval\|(% style="width:330px" %)(((
2.2	731	OK
	732
	733	Set transmit interval to 60000ms = 60 seconds
	734	)))
	735
27.2	736	(% style="color:#037691" %)Downlink Command: 0x01
2.2	737
	738	Format: Command Code (0x01) followed by 3 bytes time value.
	739
	740	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	741
	742	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	743	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	744
34.26	745
34.31	746
27.3	747	== 3.2 Set Interrupt Mode ==
	748
2.2	749	Feature, Set Interrupt mode for GPIO_EXIT.
	750
27.3	751	(% style="color:#037691" %)AT Command: AT+INTMOD
2.2	752
28.2	753	[[image:image-20220607153759-6.png]]
2.2	754
	755
27.3	756	(% style="color:#037691" %)Downlink Command: 0x06
2.2	757
	758	Format: Command Code (0x06) followed by 3 bytes.
	759
	760	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	761
	762	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	763	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	764
34.27	765
34.30	766
27.3	767	== 3.3 Calibrate Sensor ==
	768
34.28	769	Detail See [[Calibration Guide>>\|\|anchor="H2.7Calibration"]] for the user of 0x13 and 0x14 downlink commands
2.2	770
	771
	772
28.3	773	== 3.4 Get Firmware Version Info ==
	774
2.2	775	Feature: use downlink to get firmware version.
	776
27.3	777	(% style="color:#037691" %)Downlink Command: 0x26
2.2	778
29.2	779	[[image:image-20220607154718-7.png]]
2.2	780
	781	* Reply to the confirmation package: 26 01
	782	* Reply to non-confirmed packet: 26 00
	783
	784	Device will send an uplink after got this downlink command. With below payload:
	785
	786	Configures info payload:
	787
29.4	788	(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
	789	\|=(((
	790	Size(bytes)
	791	)))\|=1\|=1\|=1\|=1\|=1\|=5\|=1
2.2	792	\|Value\|Software Type\|(((
	793	Frequency
	794
	795	Band
	796	)))\|Sub-band\|(((
	797	Firmware
	798
	799	Version
	800	)))\|Sensor Type\|Reserve\|(((
29.4	801	[[Message Type>>\|\|anchor="H2.3.6MessageType"]]
2.2	802	Always 0x02
	803	)))
	804
	805	Software Type: Always 0x03 for LSPH01
	806
	807
	808	Frequency Band:
	809
	810	*0x01: EU868
	811
	812	*0x02: US915
	813
	814	*0x03: IN865
	815
	816	*0x04: AU915
	817
	818	*0x05: KZ865
	819
	820	*0x06: RU864
	821
	822	*0x07: AS923
	823
	824	*0x08: AS923-1
	825
	826	*0x09: AS923-2
	827
	828	*0xa0: AS923-3
	829
	830
	831	Sub-Band: value 0x00 ~~ 0x08
	832
	833
	834	Firmware Version: 0x0100, Means: v1.0.0 version
	835
	836
	837	Sensor Type:
	838
	839	0x01: LSE01
	840
	841	0x02: LDDS75
	842
	843	0x03: LDDS20
	844
	845	0x04: LLMS01
	846
	847	0x05: LSPH01
	848
	849	0x06: LSNPK01
	850
	851	0x07: LDDS12
	852
	853
	854
29.9	855	= 4. Battery & How to replace =
2.2	856
29.9	857	== 4.1 Battery Type ==
2.2	858
30.2	859	(((
2.2	860	LSPH01 is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
30.2	861	)))
2.2	862
30.2	863	(((
2.2	864	The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
30.2	865	)))
2.2	866
30.2	867	[[image:1654588469844-778.png]]
2.2	868
	869
	870	Minimum Working Voltage for the LSPH01:
	871
	872	LSPH01: 2.45v ~~ 3.6v
	873
	874
	875
30.3	876	== 4.2 Replace Battery ==
	877
30.5	878	(((
2.2	879	Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
30.5	880	)))
2.2	881
30.5	882	(((
2.2	883	And make sure the positive and negative pins match.
30.5	884	)))
2.2	885
	886
	887
30.4	888	== 4.3 Power Consumption Analyze ==
2.2	889
30.5	890	(((
2.2	891	Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
30.5	892	)))
2.2	893
30.5	894	(((
2.2	895	Instruction to use as below:
30.5	896	)))
2.2	897
	898
32.3	899	Step 1: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
2.2	900
	901	[[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
	902
	903
32.3	904	Step 2: Open it and choose
2.2	905
	906	* Product Model
	907	* Uplink Interval
	908	* Working Mode
	909
	910	And the Life expectation in difference case will be shown on the right.
	911
32.2	912	[[image:1654588577573-122.png]]
2.2	913
	914
	915	The battery related documents as below:
	916
32.2	917	* (((
	918	[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
2.2	919	)))
32.2	920	* (((
	921	[[Lithium-Thionyl Chloride Battery datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
	922	)))
	923	* (((
	924	[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	925	)))
2.2	926
32.2	927	[[image:image-20220607155856-8.png]]
2.2	928
	929
	930
32.4	931	=== 4.3.1 Battery Note ===
2.2	932
32.4	933	(((
2.2	934	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
32.4	935	)))
2.2	936
	937
	938
32.4	939	=== 4.3.2 Replace the battery ===
	940
2.2	941	You can change the battery in the LSPH01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	942
	943	The default battery pack of LSPH01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	944
	945
	946
33.2	947	= 5. Use AT Command =
2.2	948
33.2	949	== 5.1 Access AT Commands ==
2.2	950
	951	LSPH01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSPH01 for using AT command, as below.
	952
33.2	953	[[image:1654589001411-343.png]]
2.2	954
34.6	955	Connection:
2.2	956
34.2	957	(% style="background-color:yellow" %) USB TTL GND <~-~-~-~-> GND
2.2	958
34.2	959	(% style="background-color:yellow" %) USB TTL TXD <~-~-~-~-> UART_RXD
2.2	960
34.2	961	(% style="background-color:yellow" %) USB TTL RXD <~-~-~-~-> UART_TXD
2.2	962
	963
34.6	964	In the PC, you need to set the serial baud rate to (% style="color:green" %)9600(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
2.2	965
	966
34.2	967	[[image:1654589062541-567.png]]
2.2	968
34.32	969	Valid AT Command please check [[Configure Device>>\|\|anchor="H3.ConfigureLSPH01viaATCommandorLoRaWANDownlink"]].
2.2	970
	971
	972
34.7	973	= 6. FAQ =
2.2	974
34.7	975	== 6.1 How to change the LoRa Frequency Bands/Region ==
	976
34.8	977	You can follow the instructions for [[how to upgrade image>>\|\|anchor="H2.10200BFirmwareChangeLog"]].
2.2	978	When downloading the images, choose the required image file for download.
	979
	980
	981
34.7	982	= 7. Trouble Shooting =
2.2	983
34.7	984	== 7.1 AT Commands input doesn’t work ==
	985
34.9	986	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)ENTER(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)ENTER(%%) while press the send key, user need to add ENTER in their string.
2.2	987
	988
	989
34.9	990	= 8. Order Info =
2.2	991
34.9	992	Part Number: (% style="color:blue" %)LSPH01-XX
2.2	993
	994
34.9	995	(% style="color:blue" %)XX(%%): The default frequency band
2.2	996
34.13	997	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
34.9	998	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	999	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	1000	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	1001	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	1002	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
34.13	1003	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
34.9	1004	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
2.2	1005
34.33	1006
	1007
34.9	1008	= 9. Packing Info =
	1009
	1010
2.2	1011	Package Includes:
	1012
	1013	* LSPH01 LoRaWAN Soil Ph Sensor x 1
	1014
	1015	Dimension and weight:
	1016
	1017	* Device Size: cm
	1018	* Device Weight: g
	1019	* Package Size / pcs : cm
	1020	* Weight / pcs : g
	1021
34.33	1022
	1023
2.4	1024	= 10. Support =
2.2	1025
	1026	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
34.12	1027	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]].
2.2	1028
23.4	1029

Wiki source code of LSPH01-LoRaWAN Soil pH Sensor User Manual

Applications