Skip to Content
Last modified by Xiaoling on 2025/04/27 13:43
From version 26.11
edited by Xiaoling
on 2022/06/07 15:11
Change comment: There is no comment for this version
To version 3.1
edited by Xiaoling
on 2022/06/07 13:36
Change comment: Uploaded new attachment "1654580186518-415.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -3,11 +3,10 @@
3 3  
4 4  
5 5  
6 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png]]
6 6  
7 7  
8 -**Contents:**
9 9  
10 -{{toc/}}
11 11  
12 12  
13 13  
... ... @@ -17,30 +17,28 @@
17 17  
18 18  
19 19  
19 +1. Introduction
20 +11. ​What is LoRaWAN Soil pH Sensor
20 20  
22 +The Dragino LSPH01 is a **LoRaWAN Soil pH Sensor** for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
21 21  
22 22  
23 -= 1. Introduction =
25 +LSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil’s** pH **with high accuracy and stable value. The LSPH01 probe can be buried into soil for long time use.
24 24  
25 -== 1.1 ​What is LoRaWAN Soil pH Sensor ==
26 26  
27 -The Dragino LSPH01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil pH Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
28 +The LoRa wireless technology used in LSPH01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
28 28  
29 -LSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:#4f81bd" %)pH (%%)**with high accuracy and stable value. The LSPH01 probe can be buried into soil for long time use.
30 30  
31 -The LoRa wireless technology used in LSPH01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
31 +LSPH01 is powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use up to 5 years.
32 32  
33 -LSPH01 is powered by (% style="color:#4f81bd" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
34 34  
35 35  Each LSPH01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
36 36  
37 37  
38 -[[image:1654580186518-415.png]]
37 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.png]]
39 39  
40 -
41 -
42 -== ​1.2 Features ==
43 -
39 +*
40 +*1. ​Features
44 44  * LoRaWAN 1.0.3 Class A
45 45  * Ultra-low power consumption
46 46  * Monitor soil pH with temperature compensation.
... ... @@ -55,146 +55,167 @@
55 55  * IP68 rate for the Sensor Probe
56 56  * 8500mAh Battery for long term use
57 57  
58 -== 1.3 Probe Specification ==
59 59  
56 +1.
57 +11. Probe Specification
60 60  
61 -(% style="color:#4f81bd" %)**Soil pH:**
59 +Soil pH:
62 62  
63 -* Range: 3 ~~ 10 pH
64 -* Resolution: 0.01 pH
65 -* Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)
66 -* Temperature Compensation Range: 0 ~~ 50℃
61 +* **Range: 3 ~~ 10 pH **
62 +* **Resolution: 0.01 pH**
63 +* **Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)**
64 +* **Temperature Compensation Range: 0 ~~ 50℃**
67 67  * IP68 Protection
68 68  * Length: 3.5 meters
69 69  
70 -(% style="color:#4f81bd" %)**Soil Temperature:**
71 71  
72 -* Range -40℃～85℃
73 -* Resolution: 0.1℃
74 -* Accuracy: <±0.5℃(-10℃～40℃)，<±0.8℃ (others)
69 +Soil Temperature:
70 +
71 +* **Range** -40℃～8**5**℃
72 +* **Resolution: 0.1℃**
73 +* **Accuracy:** <±0.5℃(-10℃～40℃)，<±0.8℃ (others)
75 75  * IP68 Protection
76 76  * Length: 3.5 meters
77 77  
78 -== 1.4 ​Applications ==
79 79  
78 +*
79 +*1. ​Applications
80 80  * Smart Agriculture
81 81  
82 -== 1.5 Pin mapping and power on ==
83 83  
84 -[[image:1654580482666-473.png]]
85 85  
84 +1.
85 +11. Pin mapping and power on
86 86  
87 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image003.png]]
87 87  
88 -= 2. Configure LSPH01 to connect to LoRaWAN network =
89 89  
90 -== 2.1 How it works ==
91 91  
92 -(((
91 +
92 +
93 +1. Configure LSPH01 to connect to LoRaWAN network
94 +11. How it works
95 +
93 93  The LSPH01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSPH01. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
94 -)))
95 95  
96 -(((
97 -In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H5.200BUseATCommand"]]to set the keys in the LSPH01.
98 -)))
99 99  
99 +In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>path:#_​Using_the_AT]]to set the keys in the LSPH01.
100 100  
101 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
102 102  
103 -(((
102 +1.
103 +11. ​Quick guide to connect to LoRaWAN server (OTAA)
104 +
104 104  Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
105 -)))
106 106  
107 -(((
108 -
109 -)))
110 110  
111 -(((
108 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.png]]
109 +
110 +
112 112  The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
113 -)))
114 114  
115 -(((
116 -(% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from LSPH01.
117 -)))
118 118  
119 -(((
114 +**Step 1**: Create a device in TTN with the OTAA keys from LSPH01.
115 +
120 120  Each LSPH01 is shipped with a sticker with the default device EUI as below:
121 -)))
122 122  
123 123  
124 -[[image:image-20220607135531-1.jpeg]]
119 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image004.png]]
125 125  
126 126  
122 +
123 +
124 +
127 127  You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
128 128  
129 129  
130 130  **Register the device**
131 131  
132 -[[image:1654581442672-605.png]]
130 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image005.png]]
133 133  
134 134  
135 -
136 136  **Add APP EUI and DEV EUI**
137 137  
138 -[[image:1654581465717-368.png]]
139 139  
136 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image006.png]]
140 140  
141 141  
142 142  **Add APP EUI in the application**
143 143  
144 -[[image:1654581493871-516.png]]
145 145  
142 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image007.png]]
146 146  
147 147  
148 148  **Add APP KEY**
149 149  
150 -[[image:1654581517630-991.png]]
147 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image008.png]]
151 151  
152 152  
153 -(% style="color:blue" %)**Step 2**(%%): Power on LSPH01
150 +**Step 2**: Power on LSPH01
154 154  
155 155  
156 156  Put a Jumper on JP2 to power on the device. ( The Switch must be in FLASH position).
157 157  
158 -[[image:image-20220607135918-2.png]]
159 159  
160 160  
161 -(% style="color:blue" %)**Step 3**(%%)**:** The LSPH01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
157 +|(((
158 +
159 +)))
162 162  
163 -[[image:1654581590132-631.png]]
161 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.png]]
164 164  
165 165  
166 166  
167 -== 2.3 ​Uplink Payload ==
168 168  
169 -LSPH01 will uplink payload via LoRaWAN with below payload format: 
166 +**Step 3:** The LSPH01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
170 170  
168 +
169 +
170 +
171 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image010.png]]
172 +
173 +
174 +
175 +1.
176 +11. ​Uplink Payload
177 +
178 +LSPH01 will uplink payload via LoRaWAN with below payload format:
179 +
180 +
171 171  Uplink payload includes in total 11 bytes.
182 +
172 172  
173 173  Normal uplink payload:
174 174  
175 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
176 176  |(((
177 177  **Size**
178 178  
179 179  **(bytes)**
180 180  )))|**2**|**2**|**2**|**2**|**1**|**1**|**1**
181 -|**Value**|[[BAT>>||anchor="H2.3.1BatteryInfo"]]|(((
182 -[[Temperature>>||anchor="H2.3.2DS18B20Temperaturesensor"]]
191 +|**Value**|[[BAT>>path:#bat]]|(((
192 +[[Temperature>>path:#DS18B20]]
183 183  
184 -[[(Optional)>>||anchor="H2.3.2DS18B20Temperaturesensor"]]
185 -)))|[[Soil pH>>||anchor="H2.3.3SoilpH"]]|[[Soil Temperature>>||anchor="H2.3.4SoilTemperature"]]|(((
186 -[[Digital Interrupt (Optional)>>||anchor="H2.3.5InterruptPin"]]
194 +[[( Optional )>>path:#DS18B20]]
195 +)))|[[Soil pH>>path:#Soil_Nitrogen]]|[[Soil Temperature>>path:#Soil_Phosphorus]]|(((
196 +[[Digital Interrupt>>path:#Int_pin]]
197 +
198 +[[(Optional)>>path:#Int_pin]]
187 187  )))|Reserve|(((
188 -[[Message Type>>||anchor="H2.3.6MessageType"]]
200 +[[Message>>path:#Message_Type]]
201 +
202 +[[Type>>path:#Message_Type]]
189 189  )))
190 190  
191 -[[image:1654581735133-458.png]]
192 192  
193 193  
194 194  
195 -=== 2.3.1 Battery Info ===
208 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image010.png]]
196 196  
197 197  
211 +
212 +1.
213 +11.
214 +111. Battery Info
215 +
198 198  Check the battery voltage for LSPH01.
199 199  
200 200  Ex1: 0x0B45 = 2885mV
... ... @@ -202,12 +202,13 @@
202 202  Ex2: 0x0B49 = 2889mV
203 203  
204 204  
223 +1.
224 +11.
225 +111. DS18B20 Temperature sensor
205 205  
206 -=== 2.3.2 DS18B20 Temperature sensor ===
227 +This is optional, user can connect external DS18B20 sensor to the [[+3.3v, 1-wire and GND pin>>path:#DS18B20]] . and this field will report temperature.
207 207  
208 -This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
209 209  
210 -
211 211  **Example**:
212 212  
213 213  If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
... ... @@ -216,35 +216,40 @@
216 216  
217 217  
218 218  
219 -=== 2.3.3 Soil pH ===
238 +1.
239 +11.
240 +111. Soil pH
220 220  
221 221  Range: 0 ~~ 14 pH
222 222  
223 -**Example:**
244 +Example:
224 224  
225 -(% style="color:#037691" %)** 0x02B7(H) = 695(D) = 6.95pH**
246 +**0x02B7(H) = 695(D) = 6.95pH**
226 226  
227 227  
249 +1.
250 +11.
251 +111. Soil Temperature
228 228  
229 -=== 2.3.4 Soil Temperature ===
230 -
231 231  Get Soil Temperature 
232 232  
233 233  
234 234  **Example**:
235 235  
236 -If payload is: **0105H**:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
258 +If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
237 237  
238 -If payload is: **FF3FH** :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
260 +If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
239 239  
240 240  
241 241  
242 -=== 2.3.5 Interrupt Pin ===
264 +1.
265 +11.
266 +111. Interrupt Pin
243 243  
244 -This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2SetInterruptMode"]] for the hardware and software set up.
268 +This data field shows if this packet is generated by interrupt or not. [[Click here>>path:#Int_mod]] for the hardware and software set up.
245 245  
246 246  
247 -**Example:**
271 +Example:
248 248  
249 249  0x00: Normal uplink packet.
250 250  
... ... @@ -251,163 +251,193 @@
251 251  0x01: Interrupt Uplink Packet.
252 252  
253 253  
278 +1.
279 +11.
280 +111. Message Type
254 254  
255 -=== 2.3.6 Message Type ===
256 -
257 257  For a normal uplink payload, the message type is always 0x01.
258 258  
259 259  Valid Message Type:
260 260  
261 261  
262 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
263 -|**Message Type Code**|**Description**|**Payload**
264 -|0x01|Normal Uplink|[[Normal Uplink Payload>>||anchor="H2.3Uplink Payload"]]
265 -|0x02|Reply configures info|[[Configure Info Payload>>||anchor="H3.4GetFirmwareVersionInfo"]]
266 -|0x03|Reply Calibration Info|[[Calibration Payload>>||anchor="H2.7Calibration"]]
287 +|Message Type Code|Description|Payload
288 +|0x01|Normal Uplink|[[Normal Uplink Payload>>path:#Normal_Uplink]]
289 +|0x02|Reply configures info|[[Configure Info Payload>>path:#Configure_Info_Payload]]
290 +|0x03|Reply Calibration Info|[[Calibration Payload>>path:#Calibration_Payload]]
267 267  
268 -=== 2.3.7 Decode payload in The Things Network ===
269 269  
293 +
294 +1.
295 +11.
296 +111. ​Decode payload in The Things Network
297 +
270 270  While using TTN network, you can add the payload format to decode the payload.
271 271  
272 272  
273 -[[image:1654582541848-906.png]]
301 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.png]]
274 274  
275 -(((
276 276  The payload decoder function for TTN is here:
277 -)))
278 278  
279 -(((
280 280  LSPH01 TTN Payload Decoder: [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Decoder/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSNPK01/Decoder/]]
281 -)))
282 282  
283 283  
308 +1.
309 +11. Uplink Interval
284 284  
285 -== 2.4 Uplink Interval ==
311 +The LSPH01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
286 286  
287 -The LSPH01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
313 +[[http:~~/~~/wiki.dragino.com/index.pHp?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]
288 288  
289 289  
290 290  
291 -== 2.5 ​Show Data in DataCake IoT Server ==
317 +1.
318 +11. ​Show Data in DataCake IoT Server
292 292  
293 293  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
294 294  
295 295  
296 -(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
323 +**Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
297 297  
298 -(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
325 +**Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
299 299  
300 300  
301 -[[image:1654583683416-869.png]]
328 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image012.png]]
302 302  
303 303  
304 -[[image:1654583694084-878.png]]
331 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]
305 305  
306 306  
307 -(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
334 +Step 3: Create an account or log in Datacake.
308 308  
309 -(% style="color:blue" %)**Step 4**(%%)**: Create LSPH01 product.**
336 +Step 4: Create LSPH01 product.
310 310  
311 -[[image:1654583711590-413.png]]
338 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]
312 312  
313 313  
314 314  
315 -[[image:1654583732798-193.png]]
342 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]
316 316  
317 317  
318 -[[image:1654583749683-259.png]]
345 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]
319 319  
320 320  
321 -(% style="color:blue" %)**Step 5**(%%)**: add payload decode**
348 +Step 5: add payload decode
322 322  
323 323  Download Datacake decoder from: [[https:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Decoder/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSNPK01/Decoder/]]
324 324  
325 325  
326 -[[image:1654583770974-935.png]]
353 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]
327 327  
328 -[[image:1654583781517-146.png]]
355 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]
329 329  
330 330  
331 -[[image:1654583791351-557.png]]
358 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]
332 332  
333 333  
334 334  After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
335 335  
336 336  
337 -[[image:1654583805491-713.png]]
364 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]
338 338  
339 339  
340 340  
341 -== 2.6 Installation and Maintain ==
342 342  
343 -=== 2.6.1 Before measurement ===
344 344  
345 -(((
346 -If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
347 -)))
370 +1.
371 +11. Installation and Maintain
372 +111. Before measurement
348 348  
349 349  
375 +If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy.
350 350  
351 -=== 2.6.2 Measurement ===
352 352  
378 +1.
379 +11.
380 +111. Measurement
353 353  
354 -(% style="color:#4f81bd" %)**Measurement the soil surface:**
355 355  
356 -[[image:1654584128046-287.png]]
383 +**Measurement the soil surface**
357 357  
358 -Choose the proper measuring position. Split the surface soil according to the measured deep.
359 359  
386 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] Choose the proper measuring position. Split the surface soil according to the measured deep.
387 +
388 +
360 360  Put pure water, or rainwater to make the soil of measurement point to moist mud. Remove rocks or hard things.
361 361  
391 +
362 362  Slowly insert the probe to the measure point. Don’t use large force which will break the probe. Make sure not shake when inserting.
363 363  
394 +
364 364  Put soil over the probe after insert. And start to measure.
365 365  
366 366  
367 -(% style="color:#4f81bd" %)**Measurement inside soil:**
398 +**Measurement inside soil**
368 368  
400 +
401 +
369 369  Dig a hole with diameter > 20CM.
370 370  
404 +
371 371  Insert the probe inside, method like measure the surface.
372 372  
373 373  
408 +1.
409 +11.
410 +111. Maintain Probe
411 +1111. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
412 +1111. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
413 +1111. Probe reference electrode is also no strong, need to avoid strong force or hitting.
414 +1111. User should keep reference electrode wet while not use.
415 +1111. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
416 +1111. The probe is IP68 can be put in water.
374 374  
375 -=== 2.6.3 Maintain Probe ===
376 376  
377 -1. (((
378 -pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
379 -)))
380 -1. (((
381 -After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
382 -)))
383 -1. (((
384 -Probe reference electrode is also no strong, need to avoid strong force or hitting.
385 -)))
386 -1. (((
387 -User should keep reference electrode wet while not use.
388 -)))
389 -1. (((
390 -Avoid the probes to touch oily matter. Which will cause issue in accuracy.
391 -)))
392 -1. (((
393 -The probe is IP68 can be put in water.
394 394  
395 395  
396 -
397 -)))
398 398  
399 -== 2.7 Calibration ==
422 +1.
423 +11. Calibration
400 400  
425 +
401 401  User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
402 402  
403 -After stable, user can use below command to calibrate.
404 404  
405 -[[image:image-20220607144936-3.png]]
429 +**After stable, user can use below command to calibrate.**
406 406  
407 407  
408 -(% style="color:#037691" %)**Calibration Payload**
432 +|**pH buffer solution**|**AT Command to calibrate**|**Downlink Command**|**Read Cal Value**
433 +|**4.00**|**AT+PHCAL=4**|(((
434 +**0x13 04**
409 409  
410 -(% border="1" cellspacing="10" style="background-color:#ffffcc; width:510px" %)
436 +**Reply with Calibrate payload**
437 +)))|(((
438 +**AT+PHCAL=?**
439 +
440 +**Example 41,61,91**
441 +)))
442 +|**6.86**|**AT+PHCAL=6**|(((
443 +**0x13 06**
444 +
445 +**Reply with Calibrate payload**
446 +)))|**AT+PHCAL=?**
447 +|**9.18**|**AT+PHCAL=9**|(((
448 +**0x13 09**
449 +
450 +**Reply with Calibrate payload**
451 +)))|**AT+PHCAL=?**
452 +|**Factory Default**|**AT+PHCAL=15**|(((
453 +**0x13 15**
454 +
455 +**Reply with Calibrate payload**
456 +)))|(((
457 +**AT+PHCAL=?**
458 +
459 +**Example 151**
460 +)))
461 +
462 +
463 +Calibration Payload
464 +
411 411  |(((
412 412  **Size**
413 413  
... ... @@ -422,33 +422,37 @@
422 422  
423 423  Calibrate value
424 424  )))|Reserve|(((
425 -[[Message Type>>||anchor="H2.3.6MessageType"]]
479 +[[Message>>path:#Message_Type]]
426 426  
481 +[[Type>>path:#Message_Type]]
482 +
427 427  Always 0x03
428 428  )))
429 429  
430 430  
431 -
432 432  User can also send 0x14 downlink command to poll the current calibration payload.
433 433  
434 -[[image:image-20220607145603-4.png]]
435 435  
490 +|**Downlink Control Type**|**FPort**|**Type Code**|**Downlink payload size(bytes)**
491 +|Get Calibration Version Info|Any|14|2
492 +
436 436  * Reply to the confirmation package: 14 01
437 437  * Reply to non-confirmed packet: 14 00
438 438  
439 439  
440 440  
441 -== 2.8 Frequency Plans ==
442 442  
443 -(((
499 +1.
500 +11. Frequency Plans
501 +
444 444  The LSPH01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
445 -)))
446 446  
504 +1.
505 +11.
506 +111. EU863-870 (EU868)
447 447  
448 -=== 2.8.1 EU863-870 (EU868) ===
508 +Uplink:
449 449  
450 -(% style="color:blue" %)**Uplink:**
451 -
452 452  868.1 - SF7BW125 to SF12BW125
453 453  
454 454  868.3 - SF7BW125 to SF12BW125 and SF7BW250
... ... @@ -468,7 +468,7 @@
468 468  868.8 - FSK
469 469  
470 470  
471 -(% style="color:blue" %)**Downlink:**
529 +Downlink:
472 472  
473 473  Uplink channels 1-9 (RX1)
474 474  
... ... @@ -475,31 +475,29 @@
475 475  869.525 - SF9BW125 (RX2 downlink only)
476 476  
477 477  
536 +1.
537 +11.
538 +111. US902-928(US915)
478 478  
479 -=== 2.8.2 US902-928(US915) ===
480 -
481 -(((
482 482  Used in USA, Canada and South America. Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
483 -)))
484 484  
485 -(((
542 +
486 486  To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
487 -)))
488 488  
489 -(((
545 +
490 490  After Join success, the end node will switch to the correct sub band by:
491 -)))
492 492  
493 493  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
494 494  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
495 495  
496 496  
552 +1.
553 +11.
554 +111. CN470-510 (CN470)
497 497  
498 -=== 2.8.3 CN470-510 (CN470) ===
499 -
500 500  Used in China, Default use CHE=1
501 501  
502 -(% style="color:blue" %)**Uplink:**
558 +Uplink:
503 503  
504 504  486.3 - SF7BW125 to SF12BW125
505 505  
... ... @@ -518,7 +518,7 @@
518 518  487.7 - SF7BW125 to SF12BW125
519 519  
520 520  
521 -(% style="color:blue" %)**Downlink:**
577 +Downlink:
522 522  
523 523  506.7 - SF7BW125 to SF12BW125
524 524  
... ... @@ -539,44 +539,42 @@
539 539  505.3 - SF12BW125 (RX2 downlink only)
540 540  
541 541  
598 +1.
599 +11.
600 +111. AU915-928(AU915)
542 542  
543 -=== 2.8.4 AU915-928(AU915) ===
544 544  
545 -(((
546 546  Frequency band as per definition in LoRaWAN 1.0.3 Regional document.
547 -)))
548 548  
549 -(((
605 +
550 550  To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
551 -)))
552 552  
553 -(((
554 -
555 -)))
556 556  
557 -(((
558 558  After Join success, the end node will switch to the correct sub band by:
559 -)))
560 560  
561 561  * Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
562 562  * Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
563 563  
564 -=== 2.8.5 AS920-923 & AS923-925 (AS923) ===
565 565  
566 -(% style="color:blue" %)**Default Uplink channel:**
567 567  
616 +1.
617 +11.
618 +111. AS920-923 & AS923-925 (AS923)
619 +
620 +
621 +**Default Uplink channel:**
622 +
568 568  923.2 - SF7BW125 to SF10BW125
569 569  
570 570  923.4 - SF7BW125 to SF10BW125
571 571  
572 572  
573 -(% style="color:blue" %)**Additional Uplink Channel**:
628 +**Additional Uplink Channel**:
574 574  
575 575  (OTAA mode, channel added by JoinAccept message)
576 576  
632 +**AS920~~AS923 for Japan, Malaysia, Singapore**:
577 577  
578 -(% style="color:blue" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
579 -
580 580  922.2 - SF7BW125 to SF10BW125
581 581  
582 582  922.4 - SF7BW125 to SF10BW125
... ... @@ -590,7 +590,7 @@
590 590  922.0 - SF7BW125 to SF10BW125
591 591  
592 592  
593 -(% style="color:blue" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
647 +**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
594 594  
595 595  923.6 - SF7BW125 to SF10BW125
596 596  
... ... @@ -605,18 +605,20 @@
605 605  924.6 - SF7BW125 to SF10BW125
606 606  
607 607  
608 -(% style="color:blue" %)**Downlink:**
609 609  
663 +**Downlink:**
664 +
610 610  Uplink channels 1-8 (RX1)
611 611  
612 612  923.2 - SF10BW125 (RX2)
613 613  
614 614  
670 +1.
671 +11.
672 +111. KR920-923 (KR920)
615 615  
616 -=== 2.8.6 KR920-923 (KR920) ===
674 +Default channel:
617 617  
618 -(% style="color:blue" %)**Default channel:**
619 -
620 620  922.1 - SF7BW125 to SF12BW125
621 621  
622 622  922.3 - SF7BW125 to SF12BW125
... ... @@ -624,7 +624,7 @@
624 624  922.5 - SF7BW125 to SF12BW125
625 625  
626 626  
627 -(% style="color:blue" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
683 +Uplink: (OTAA mode, channel added by JoinAccept message)
628 628  
629 629  922.1 - SF7BW125 to SF12BW125
630 630  
... ... @@ -641,7 +641,7 @@
641 641  923.3 - SF7BW125 to SF12BW125
642 642  
643 643  
644 -(% style="color:blue" %)**Downlink:**
700 +Downlink:
645 645  
646 646  Uplink channels 1-7(RX1)
647 647  
... ... @@ -648,10 +648,13 @@
648 648  921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
649 649  
650 650  
651 -=== 2.8.7 IN865-867 (IN865) ===
707 +1.
708 +11.
709 +111. IN865-867 (IN865)
652 652  
653 -(% style="color:blue" %)**Uplink:**
654 654  
712 +Uplink:
713 +
655 655  865.0625 - SF7BW125 to SF12BW125
656 656  
657 657  865.4025 - SF7BW125 to SF12BW125
... ... @@ -659,7 +659,7 @@
659 659  865.9850 - SF7BW125 to SF12BW125
660 660  
661 661  
662 -(% style="color:blue" %)**Downlink:**
721 +Downlink:
663 663  
664 664  Uplink channels 1-3 (RX1)
665 665  
... ... @@ -666,22 +666,27 @@
666 666  866.550 - SF10BW125 (RX2)
667 667  
668 668  
728 +1.
729 +11. LED Indicator
669 669  
670 -== 2.9 LED Indicator ==
671 -
672 672  The LSPH01 has an internal LED which is to show the status of different state.
673 673  
733 +
674 674  * The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
675 675  * Blink once when device transmit a packet.
676 676  
677 -== 2.10 ​Firmware Change Log ==
678 678  
738 +
739 +
740 +1.
741 +11. ​Firmware Change Log
742 +
679 679  **Firmware download link:**
680 680  
681 681  [[http:~~/~~/www.dragino.com/downloads/index.pHp?dir=LoRa_End_Node/LSPH01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
682 682  
683 683  
684 -**Firmware Upgrade Method:[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]**
748 +**Firmware Upgrade Method:**
685 685  
686 686  [[http:~~/~~/wiki.dragino.com/index.pHp?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction]]
687 687  
... ... @@ -740,6 +740,7 @@
740 740  Set transmit interval to 60000ms = 60 seconds
741 741  )))
742 742  
807 +
743 743  **Downlink Command: 0x01**
744 744  
745 745  Format: Command Code (0x01) followed by 3 bytes time value.
... ... @@ -749,6 +749,9 @@
749 749  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
750 750  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
751 751  
817 +
818 +
819 +
752 752  1.
753 753  11. Set Interrupt Mode
754 754  
... ... @@ -773,6 +773,7 @@
773 773  1. (Trigger by rising edge)
774 774  )))|OK
775 775  
844 +
776 776  **Downlink Command: 0x06**
777 777  
778 778  Format: Command Code (0x06) followed by 3 bytes.
... ... @@ -782,6 +782,8 @@
782 782  * Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
783 783  * Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
784 784  
854 +
855 +
785 785  1.
786 786  11. Calibrate Sensor
787 787  
... ... @@ -801,9 +801,11 @@
801 801  |**Downlink Control Type**|**FPort**|**Type Code**|**Downlink payload size(bytes)**
802 802  |Get Firmware Version Info|Any|26|2
803 803  
875 +
804 804  * Reply to the confirmation package: 26 01
805 805  * Reply to non-confirmed packet: 26 00
806 806  
879 +
807 807  Device will send an uplink after got this downlink command. With below payload:
808 808  
809 809  Configures info payload:
... ... @@ -829,6 +829,7 @@
829 829  Always 0x02
830 830  )))
831 831  
905 +
832 832  **Software Type**: Always 0x03 for LSPH01
833 833  
834 834  
... ... @@ -910,6 +910,7 @@
910 910  1.
911 911  11. Power Consumption Analyze
912 912  
987 +
913 913  Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
914 914  
915 915  
... ... @@ -938,6 +938,8 @@
938 938  * [[Lithium-Thionyl Chloride Battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] datasheet
939 939  * [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
940 940  
1016 +
1017 +
941 941  |(((
942 942  JST-XH-2P connector
943 943  )))
... ... @@ -946,7 +946,7 @@
946 946  
947 947  
948 948  
949 -1.
1026 +1.
950 950  11.
951 951  111. ​Battery Note
952 952  
... ... @@ -970,6 +970,7 @@
970 970  1. Use AT Command
971 971  11. Access AT Commands
972 972  
1050 +
973 973  LSPH01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSPH01 for using AT command, as below.
974 974  
975 975  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]
... ... @@ -1004,11 +1004,13 @@
1004 1004  1. Trouble Shooting
1005 1005  11. AT Commands input doesn’t work
1006 1006  
1085 +
1007 1007  In the case if user can see the console output but can’t type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn’t send **ENTER** while press the send key, user need to add ENTER in their string.
1008 1008  
1009 1009  
1010 1010  1. Order Info
1011 1011  
1091 +
1012 1012  Part Number: **LSPH01-XX**
1013 1013  
1014 1014  
... ... @@ -1023,6 +1023,8 @@
1023 1023  * **IN865**: LoRaWAN IN865 band
1024 1024  * **CN470**: LoRaWAN CN470 band
1025 1025  
1106 +
1107 +
1026 1026  1. ​Packing Info
1027 1027  
1028 1028  **Package Includes**:
... ... @@ -1029,6 +1029,7 @@
1029 1029  
1030 1030  * LSPH01 LoRaWAN Soil Ph Sensor x 1
1031 1031  
1114 +
1032 1032  **Dimension and weight**:
1033 1033  
1034 1034  * Device Size: cm
... ... @@ -1036,6 +1036,8 @@
1036 1036  * Package Size / pcs : cm
1037 1037  * Weight / pcs : g
1038 1038  
1122 +
1123 +
1039 1039  = 10. ​Support =
1040 1040  
1041 1041  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1654580428909-307.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -492.6 KB
Content
1654580482666-473.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -492.6 KB
Content
1654581442672-605.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -59.6 KB
Content
1654581465717-368.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -62.1 KB
Content
1654581493871-516.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -83.1 KB
Content
1654581517630-991.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -65.2 KB
Content
1654581590132-631.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -42.6 KB
Content
1654581735133-458.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -42.6 KB
Content
1654582541848-906.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -59.2 KB
Content
1654583683416-869.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -62.2 KB
Content
1654583694084-878.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -66.6 KB
Content
1654583711590-413.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -246.2 KB
Content
1654583732798-193.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -199.6 KB
Content
1654583749683-259.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -129.1 KB
Content
1654583770974-935.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -37.7 KB
Content
1654583781517-146.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -64.0 KB
Content
1654583791351-557.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -11.3 KB
Content
1654583805491-713.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -127.1 KB
Content
1654584128046-287.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -345.3 KB
Content
image-20220607135531-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -16.5 KB
Content
image-20220607135918-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -99.6 KB
Content
image-20220607144936-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -23.6 KB
Content
image-20220607145603-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -5.8 KB
Content