LS -- LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

Version 91.1 by Xiaoling on 2025/04/09 17:52

version	line-number	content
73.2	1	(% style="display:none" %) (%%) (% style="display:none" %) (%%) (% style="display:none" %)
1.1	2
73.2	3	(% style="text-align:center" %)
	4	[[image:image-20240104162316-6.png]]
1.1	5
73.2	6
	7
	8
	9
	10
	11
76.5	12	Table of Contents:
30.1	13
1.1	14	{{toc/}}
	15
	16
	17
	18
	19
	20
31.1	21	= 1. Introduction =
1.1	22
73.3	23	== 1.1 What is S31x-LB/LS LoRaWAN Temperature & Humidity Sensor ==
1.1	24
39.6	25
73.3	26	The Dragino S31x-LB/LS is a (% style="color:blue" %)LoRaWAN Temperature and Humidity Sensor(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)surrounding environment temperature and relative air humidity precisely(%%), and then upload to IoT server via LoRaWAN wireless protocol.
1.1	27
73.3	28	The temperature & humidity sensor used in S31x-LB/LS is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)waterproof anti-condensation casing(%%) for long term use.
1.1	29
73.3	30	The LoRa wireless technology used in S31x-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
1.1	31
73.3	32	S31x-LB/LS supports (% style="color:blue" %)Temperature & Humdity alarm feature(%%), user can set temperature alarm for instant notice. S31x-LB/LS supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
1.1	33
73.3	34	S31x-LB/LS (% style="color:blue" %)supports BLE configure(%%) and (% style="color:blue" %)wireless OTA update(%%) which make user easy to use.
1.1	35
77.1	36	S31x-LB/LS is powered by (% style="color:blue" %)8500mAh Li-SOCI2 battery(%%) or (% style="color:blue" %)solar powered + Li-ion battery(%%) it is designed for long term use up to 5 years.
1.1	37
73.3	38	Each S31x-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
1.1	39
	40
	41	== 1.2 Features ==
	42
39.6	43
1.1	44	* LoRaWAN 1.0.3 Class A
	45	* Ultra-low power consumption
5.1	46	* External 3 meters SHT31 probe (For S31-LB)
67.2	47	* Measure range -40°C ~~ 80°C
5.1	48	* Temperature & Humidity alarm
1.1	49	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	50	* Support Bluetooth v5.1 and LoRaWAN remote configure
	51	* Support wireless OTA update firmware
	52	* Uplink on periodically
	53	* Downlink to change configure
76.12	54	* 8500mAh Li/SOCl2 Battery (S31/S31B-LB)
77.1	55	* Solar panel + 3000mAh Li-ion battery (S31/S31B-LS)
1.1	56
	57	== 1.3 Specification ==
	58
	59
	60	(% style="color:#037691" %)Common DC Characteristics:
	61
73.4	62	* Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
1.1	63	* Operating Temperature: -40 ~~ 85°C
	64
	65	(% style="color:#037691" %)Temperature Sensor:
	66
5.1	67	* Range: -40 to + 80°C
	68	* Accuracy: ±0.2 @ 0-90 °C
	69	* Resolution: 0.1°C
	70	* Long Term Shift: <0.03 °C/yr
1.1	71
5.1	72	(% style="color:#037691" %)Humidity Sensor:
	73
	74	* Range: 0 ~~ 99.9% RH
	75	* Accuracy: ± 2%RH ( 0 ~~ 100%RH)
	76	* Resolution: 0.01% RH
	77	* Long Term Shift: <0.25 %RH/yr
	78
1.1	79	(% style="color:#037691" %)LoRa Spec:
	80
	81	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	82	* Max +22 dBm constant RF output vs.
	83	* RX sensitivity: down to -139 dBm.
	84	* Excellent blocking immunity
	85
	86	(% style="color:#037691" %)Battery:
	87
	88	* Li/SOCI2 un-chargeable battery
	89	* Capacity: 8500mAh
	90	* Self-Discharge: <1% / Year @ 25°C
	91	* Max continuously current: 130mA
	92	* Max boost current: 2A, 1 second
	93
	94	(% style="color:#037691" %)Power Consumption
	95
	96	* Sleep Mode: 5uA @ 3.3v
	97	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	98
	99	== 1.4 Sleep mode and working mode ==
	100
	101
	102	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
	103
	104	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
	105
	106
	107	== 1.5 Button & LEDs ==
	108
	109
73.6	110	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1\|\|alt="image-20240103160425-4.png"]]
1.1	111
76.13	112	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
	113	\|=(% style="width: 167px;background-color:#4F81BD;color:white" %)Behavior on ACT\|=(% style="width: 117px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 226px;background-color:#4F81BD;color:white" %)Action
1.1	114	\|(% style="width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="width:117px" %)Send an uplink\|(% style="width:225px" %)(((
	115	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
	116	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	117	)))
	118	\|(% style="width:167px" %)Pressing ACT for more than 3s\|(% style="width:117px" %)Active Device\|(% style="width:225px" %)(((
	119	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	120	(% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	121	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	122	)))
6.1	123	\|(% style="width:167px" %)Fast press ACT 5 times.\|(% style="width:117px" %)Deactivate Device\|(% style="width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
1.1	124
	125	== 1.6 BLE connection ==
	126
	127
73.4	128	S31x-LB/LS support BLE remote configure.
1.1	129
	130
	131	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	132
	133	* Press button to send an uplink
	134	* Press button to active device.
	135	* Device Power on or reset.
	136
	137	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	138
	139
43.1	140	== 1.7 Pin Definitions ==
1.1	141
	142
43.1	143
77.1	144	[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/image-20240926134323-1.png?rev=1.1\|\|alt="image-20240926134323-1.png"]]
	145
	146
45.2	147	== 1.8 Hardware Variant ==
43.1	148
	149
76.13	150	(% border="1" cellspacing="3" style="width:460px" %)
76.2	151	\|=(% style="width: 102px;background-color:#4F81BD;color:white" %)Model\|=(% style="width: 182px; background-color:#4F81BD;color:white" %)Photo\|=(% style="width: 176px; background-color:#4F81BD;color:white" %)Probe Info
44.1	152	\|(% style="width:102px" %)(((
73.6	153	S31-LB/LS
76.7	154	)))\|(% style="width:182px" %)(((
	155	(% style="text-align:center" %)
	156	[[image:image-20240104165223-7.png]]
	157	)))\|(% style="width:176px" %)(((
6.1	158	1 x SHT31 Probe
1.1	159
	160	Cable Length : 2 meters
	161
	162
	163	)))
44.1	164	\|(% style="width:102px" %)(((
73.6	165	S31B-LB/LS
76.7	166	)))\|(% style="width:182px" %)(((
	167	(% style="text-align:center" %)
	168	[[image:image-20240104165338-9.png]]
	169	)))\|(% style="width:176px" %)(((
6.1	170	1 x SHT31 Probe
1.1	171
6.1	172	Installed in device.
1.1	173	)))
	174
	175	(% style="display:none" %)
	176
	177
	178
43.1	179	== 1.9 Mechanical ==
1.1	180
73.6	181	=== 1.9.1 for LB version ===
1.1	182
89.2	183	[[image:image-20250409174350-1.jpeg]]
1.1	184
	185
	186
	187
73.6	188	=== 1.9.2 for LS version ===
	189
	190
89.2	191	[[image:image-20250409174410-2.jpeg]]
73.6	192
	193
73.4	194	= 2. Configure S31x-LB/LS to connect to LoRaWAN network =
1.1	195
	196	== 2.1 How it works ==
	197
	198
73.4	199	The S31x-LB/LS is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
1.1	200
	201
	202	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
	203
	204
	205	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	206
	207	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	208
	209
73.4	210	(% style="color:blue" %)Step 1:(%%) Create a device in TTN with the OTAA keys from S31x-LB/LS.
1.1	211
73.4	212	Each S31x-LB/LS is shipped with a sticker with the default device EUI as below:
1.1	213
30.1	214	[[image:image-20230426084152-1.png\|\|alt="图片-20230426084152-1.png" height="233" width="502"]]
1.1	215
	216
	217	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	218
	219
	220	(% style="color:blue" %)Register the device
	221
83.2	222	[[image:image-20250328173145-1.jpeg]]
1.1	223
	224
	225	(% style="color:blue" %)Add APP EUI and DEV EUI
	226
83.2	227	[[image:image-20250328173203-2.jpeg]]
1.1	228
	229
	230	(% style="color:blue" %)Add APP EUI in the application
	231
	232
83.2	233	[[image:image-20250328173224-3.jpeg]]
1.1	234
	235
	236	(% style="color:blue" %)Add APP KEY
	237
83.2	238	[[image:image-20250328173243-4.jpeg]]
1.1	239
73.4	240	(% style="color:blue" %)Step 2:(%%) Activate on S31x-LB/LS
1.1	241
73.4	242	Press the button for 5 seconds to activate the S31x-LB/LS.
6.1	243
1.1	244	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	245
	246	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	247
	248
	249	== 2.3 Uplink Payload ==
	250
	251	=== 2.3.1 Device Status, FPORT~=5 ===
	252
	253
73.4	254	Users can use the downlink command(0x26 01) to ask S31x-LB/LS to send device configure detail, include device configure status. S31x-LB/LS will uplink a payload via FPort=5 to server.
1.1	255
	256	The Payload format is as below.
	257
76.14	258	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
76.4	259	\|(% colspan="6" style="background-color:#4f81bd; color:white" %)Device Status (FPORT=5)
1.1	260	\|(% style="width:103px" %)Size (bytes)\|(% style="width:72px" %)1\|2\|(% style="width:91px" %)1\|(% style="width:86px" %)1\|(% style="width:44px" %)2
76.4	261	\|(% style="width:103px" %)Value\|(% style="width:72px" %)Sensor Model\|Firmware Version\|(% style="width:91px" %)Frequency Band\|(% style="width:86px" %)Sub-band\|(% style="width:44px" %)BAT
1.1	262
	263	Example parse in TTNv3
	264
58.2	265	[[image:image-20230524144422-1.png\|\|height="174" width="1080"]]
1.1	266
	267
73.4	268	(% style="color:#037691" %)Sensor Model(%%): For S31x-LB/LS, this value is 0x0A
1.1	269
	270	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
	271
	272	(% style="color:#037691" %)Frequency Band:
	273
64.2	274	0x01: EU868
1.1	275
64.2	276	0x02: US915
1.1	277
64.2	278	0x03: IN865
1.1	279
64.2	280	0x04: AU915
1.1	281
64.2	282	0x05: KZ865
1.1	283
64.2	284	0x06: RU864
1.1	285
64.2	286	0x07: AS923
1.1	287
64.2	288	0x08: AS923-1
1.1	289
64.2	290	0x09: AS923-2
1.1	291
64.2	292	0x0a: AS923-3
1.1	293
64.2	294	0x0b: CN470
1.1	295
64.2	296	0x0c: EU433
1.1	297
64.2	298	0x0d: KR920
1.1	299
64.2	300	0x0e: MA869
1.1	301
	302
	303	(% style="color:#037691" %)Sub-Band:
	304
	305	AU915 and US915:value 0x00 ~~ 0x08
	306
	307	CN470: value 0x0B ~~ 0x0C
	308
	309	Other Bands: Always 0x00
	310
	311
	312	(% style="color:#037691" %)Battery Info:
	313
	314	Check the battery voltage.
	315
	316	Ex1: 0x0B45 = 2885mV
	317
	318	Ex2: 0x0B49 = 2889mV
	319
	320
	321	=== 2.3.2 Sensor Data. FPORT~=2 ===
	322
	323
7.1	324	Sensor Data is uplink via FPORT=2
1.1	325
76.14	326	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)
76.2	327	\|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
7.1	328	Size(bytes)
76.2	329	)))\|=(% style="width: 40px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)4\|=(% style="width: 150px; background-color: #4F81BD;color:white" %)1\|=(% style="width: 80px; background-color: #4F81BD;color:white" %)2\|=(% style="width: 80px; background-color: #4F81BD;color:white" %)2
60.8	330	\|(% style="width:99px" %)Value\|(% style="width:69px" %)(((
55.5	331	Battery
14.15	332	)))\|(% style="width:130px" %)(((
55.5	333	Unix TimeStamp
46.1	334	)))\|(% style="width:194px" %)(((
60.3	335	Alarm Flag & MOD& Level of PA8
46.1	336	)))\|(% style="width:106px" %)(((
55.5	337	Temperature
46.1	338	)))\|(% style="width:97px" %)(((
55.5	339	Humidity
7.1	340	)))
1.1	341
58.2	342	[[image:image-20230524144456-2.png\|\|height="180" width="1142"]]
58.1	343
	344
51.1	345	==== (% style="color:#4472c4" %)Battery(%%) ====
1.1	346
	347	Sensor Battery Level.
	348
	349	Ex1: 0x0B45 = 2885mV
	350
	351	Ex2: 0x0B49 = 2889mV
	352
	353
51.1	354	==== (% style="color:#4472c4" %)Temperature(%%) ====
1.1	355
	356	Example:
	357
	358	If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
	359
	360	If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
	361
76.16	362	(FF3F & 8000:Judge whether the highest bit is 1, when the highest bit is 1, it is negative)
1.1	363
	364
51.1	365	==== (% style="color:#4472c4" %)Humidity(%%) ====
1.1	366
7.1	367	Read:0x(0197)=412 Value: 412 / 10=41.2, So 41.2%
1.1	368
	369
55.1	370	==== (% style="color:#4472c4" %)Alarm Flag & MOD & Level of PA8(%%) ====
1.1	371
	372	Example:
	373
46.1	374	If payload & 0x01 = 0x01 ~-~-> This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
1.1	375
46.1	376	If payload & 0x01 = 0x00 ~-~-> This is a normal uplink message, no alarm.
1.1	377
46.1	378	If payload & 0x80>>7 = 0x01 ~-~-> The PA8 is low level.
1.1	379
46.1	380	If payload & 0x80>>7 =0x00 ~-~-> The PA8 is high level.
	381
	382	If payload >> 2 = 0x00 ~-~-> means MOD=1, This is a sampling uplink message.
	383
8.1	384	If payload >> 2 = 0x31 ~-~-> means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail.
1.1	385
	386
	387	== 2.4 Payload Decoder file ==
	388
14.22	389
10.1	390	In TTN, use can add a custom payload so it shows friendly reading
1.1	391
10.1	392	In the page (% style="color:#037691" %)Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder(%%) to add the decoder from:
1.1	393
40.1	394	[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
1.1	395
10.1	396
1.1	397	== 2.5 Datalog Feature ==
	398
	399
73.4	400	Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB/LS will store the reading for future retrieving purposes.
1.1	401
	402
	403	=== 2.5.1 Ways to get datalog via LoRaWAN ===
	404
	405
76.10	406	Set PNACKMD=1, S31x-LB/LS will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB/LS will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
1.1	407
44.1	408	* (((
73.4	409	a) S31x-LB/LS will do an ACK check for data records sending to make sure every data arrive server.
44.1	410	)))
	411	* (((
73.4	412	b) S31x-LB/LS will send data in CONFIRMED Mode when PNACKMD=1, but S31x-LB/LS won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB/LS gets a ACK, S31x-LB/LS will consider there is a network connection and resend all NONE-ACK messages.
44.1	413	)))
1.1	414
	415	=== 2.5.2 Unix TimeStamp ===
	416
	417
73.4	418	S31x-LB/LS uses Unix TimeStamp format based on
1.1	419
85.2	420	[[image:image-20250328173339-5.jpeg]]
1.1	421
	422	User can get this time from link: [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
	423
	424	Below is the converter example
	425
85.2	426	[[image:image-20250328173355-6.jpeg]]
1.1	427
39.5	428
1.1	429	So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
	430
	431
	432	=== 2.5.3 Set Device Time ===
	433
	434
14.24	435	User need to set (% style="color:blue" %)SYNCMOD=1(%%) to enable sync time via MAC command.
1.1	436
73.4	437	Once S31x-LB/LS Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB/LS. If S31x-LB/LS fails to get the time from the server, S31x-LB/LS will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
1.1	438
14.24	439	(% style="color:red" %)Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.
1.1	440
	441
11.1	442	=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
1.1	443
	444
11.1	445	The Datalog uplinks will use below payload format.
1.1	446
	447	Retrieval data payload:
	448
76.15	449	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)
76.2	450	\|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
1.1	451	Size(bytes)
76.2	452	)))\|=(% style="width: 40px; background-color:#4F81BD;color:white" %)2\|=(% style="width: 55px; background-color:#4F81BD;color:white" %)2\|=(% style="width: 65px; background-color:#4F81BD;color:white" %)2\|=(% style="width: 180px; background-color:#4F81BD;color:white" %)1\|=(% style="width: 100px; background-color:#4F81BD;color:white" %)4
60.13	453	\|(% style="width:103px" %)Value\|(% style="width:68px" %)(((
46.1	454	ignore
	455	)))\|(% style="width:104px" %)(((
55.1	456	(((
	457	Humidity
	458	)))
	459	)))\|(% style="width:87px" %)(((
46.1	460	Temperature
55.1	461	)))\|(% style="width:178px" %)(((
60.10	462	Poll message flag & Alarm Flag& Level of PA8
46.1	463	)))\|(% style="width:137px" %)Unix Time Stamp
	464
55.1	465	Poll message flag & Alarm Flag & Level of PA8:
46.1	466
55.1	467	[[image:image-20230524114302-1.png\|\|height="115" width="736"]]
1.1	468
55.1	469
14.25	470	No ACK Message: 1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for PNACKMD=1 feature)
1.1	471
	472	Poll Message Flag: 1: This message is a poll message reply.
	473
	474	* Poll Message Flag is set to 1.
	475
	476	* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
	477
	478	For example, in US915 band, the max payload for different DR is:
	479
	480	a) DR0: max is 11 bytes so one entry of data
	481
	482	b) DR1: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
	483
	484	c) DR2: total payload includes 11 entries of data
	485
	486	d) DR3: total payload includes 22 entries of data.
	487
	488	If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0
	489
	490	Example:
	491
73.4	492	If S31x-LB/LS has below data inside Flash:
1.1	493
55.1	494	[[image:image-20230524114654-2.png]]
1.1	495
	496
55.1	497	If user sends below downlink command: 31646D84E1646D856C05
1.1	498
55.1	499	Where : Start time: 646D84E1 = time 23/5/24 03:30:41
1.1	500
55.1	501	Stop time: 646D856C= time 23/5/24 03:33:00
14.26	502
55.1	503
73.4	504	S31x-LB/LS will uplink this payload.
1.1	505
58.2	506	[[image:image-20230524114826-3.png\|\|height="448" width="1244"]]
1.1	507
14.44	508	(((
55.1	509	00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
14.44	510	)))
1.1	511
14.44	512	(((
1.1	513	Where the first 11 bytes is for the first entry:
14.44	514	)))
1.1	515
14.44	516	(((
55.1	517	00 00 02 36 01 10 40 64 6D 84 E1
14.44	518	)))
1.1	519
14.44	520	(((
55.1	521	Hum=0x0236/10=56.6
14.44	522	)))
1.1	523
14.44	524	(((
55.1	525	Temp=0x0110/10=27.2
14.44	526	)))
1.1	527
14.44	528	(((
55.1	529	poll message flag & Alarm Flag & Level of PA8=0x40,means reply data,sampling uplink message,the PA8 is low level.
14.44	530	)))
1.1	531
14.44	532	(((
55.1	533	Unix time is 0x646D84E1=1684899041s=23/5/24 03:30:41
14.44	534	)))
1.1	535
	536
30.1	537	(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
1.1	538
	539	== 2.6 Temperature Alarm Feature ==
	540
	541
73.4	542	S31x-LB/LS work flow with Alarm feature.
1.1	543
	544
51.1	545	[[image:image-20230524110125-3.png\|\|height="768" width="1115"]]
1.1	546
	547
51.1	548
1.1	549	== 2.7 Frequency Plans ==
	550
	551
76.9	552	The S31x-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
1.1	553
	554	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
	555
	556
60.19	557	== 2.8 Firmware Change Log ==
	558
	559
	560	Firmware download link: [[https:~~/~~/www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]
	561
	562
73.4	563	= 3. Configure S31x-LB/LS =
1.1	564
16.4	565	== 3.1 Configure Methods ==
1.1	566
	567
73.4	568	S31x-LB/LS supports below configure method:
1.1	569
	570	* AT Command via Bluetooth Connection (Recommended): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
11.1	571	* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
1.1	572	* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
	573
	574	== 3.2 General Commands ==
	575
	576
	577	These commands are to configure:
	578
	579	* General system settings like: uplink interval.
	580	* LoRaWAN protocol & radio related command.
	581
	582	They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	583
	584	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	585
	586
73.4	587	== 3.3 Commands special design for S31x-LB/LS ==
1.1	588
	589
73.4	590	These commands only valid for S31x-LB/LS, as below:
1.1	591
	592
	593	=== 3.3.1 Set Transmit Interval Time ===
	594
	595
	596	Feature: Change LoRaWAN End Node Transmit Interval.
	597
	598	(% style="color:blue" %)AT Command: AT+TDC
	599
76.15	600	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
76.2	601	\|=(% style="width: 156px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 137px;background-color:#4F81BD;color:white" %)Function\|=(% style="background-color:#4F81BD;color:white" %)Response
1.1	602	\|(% style="width:156px" %)AT+TDC=?\|(% style="width:137px" %)Show current transmit Interval\|(((
	603	30000
	604	OK
	605	the interval is 30000ms = 30s
	606	)))
	607	\|(% style="width:156px" %)AT+TDC=60000\|(% style="width:137px" %)Set Transmit Interval\|(((
	608	OK
	609	Set transmit interval to 60000ms = 60 seconds
	610	)))
	611
	612	(% style="color:blue" %)Downlink Command: 0x01
	613
	614	Format: Command Code (0x01) followed by 3 bytes time value.
	615
	616	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
	617
	618	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	619	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	620
	621	=== 3.3.2 Get Device Status ===
	622
	623
	624	Send a LoRaWAN downlink to ask device send Alarm settings.
	625
14.31	626	(% style="color:blue" %)Downlink Payload: (%%)0x26 01
1.1	627
	628	Sensor will upload Device Status via FPORT=5. See payload section for detail.
	629
	630
16.4	631	=== 3.3.3 Set Temperature Alarm Threshold ===
1.1	632
39.6	633
14.34	634	* (% style="color:blue" %)AT Command:
1.1	635
14.34	636	(% style="color:#037691" %)AT+SHTEMP=min,max
1.1	637
11.1	638	* When min=0, and max≠0, Alarm higher than max
	639	* When min≠0, and max=0, Alarm lower than min
	640	* When min≠0 and max≠0, Alarm higher than max or lower than min
1.1	641
11.1	642	Example:
1.1	643
11.1	644	AT+SHTEMP=0,30 ~/~/ Alarm when temperature higher than 30.
1.1	645
14.34	646	* (% style="color:blue" %)Downlink Payload:
1.1	647
14.45	648	(% style="color:#037691" %)0x(0C 01 00 1E) (%%) ~/~/ Set AT+SHTEMP=0,30
1.1	649
14.34	650	(% style="color:red" %)(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)
1.1	651
	652
16.4	653	=== 3.3.4 Set Humidity Alarm Threshold ===
1.1	654
39.6	655
14.34	656	* (% style="color:blue" %)AT Command:
1.1	657
14.34	658	(% style="color:#037691" %)AT+SHHUM=min,max
1.1	659
11.1	660	* When min=0, and max≠0, Alarm higher than max
	661	* When min≠0, and max=0, Alarm lower than min
	662	* When min≠0 and max≠0, Alarm higher than max or lower than min
1.1	663
11.1	664	Example:
1.1	665
14.45	666	AT+SHHUM=70,0 ~/~/ Alarm when humidity lower than 70%.
1.1	667
14.34	668	* (% style="color:blue" %)Downlink Payload:
1.1	669
14.45	670	(% style="color:#037691" %)0x(0C 02 46 00)(%%) ~/~/ Set AT+SHTHUM=70,0
1.1	671
14.34	672	(% style="color:red" %)(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))
1.1	673
	674
16.4	675	=== 3.3.5 Set Alarm Interval ===
1.1	676
39.6	677
1.1	678	The shortest time of two Alarm packet. (unit: min)
	679
14.34	680	* (% style="color:blue" %)AT Command:
1.1	681
14.34	682	(% style="color:#037691" %)AT+ATDC=30 (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
1.1	683
14.34	684	* (% style="color:blue" %)Downlink Payload:
1.1	685
14.34	686	(% style="color:#037691" %)0x(0D 00 1E)(%%) ~-~--> Set AT+ATDC=0x 00 1E = 30 minutes
1.1	687
	688
16.4	689	=== 3.3.6 Get Alarm settings ===
1.1	690
	691
	692	Send a LoRaWAN downlink to ask device send Alarm settings.
	693
	694	* (% style="color:#037691" %)Downlink Payload: (%%)0x0E 01
	695
	696	Example:
	697
51.1	698	[[image:image-20230524110211-4.png]]
1.1	699
	700	Explain:
	701
	702	* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
	703
16.4	704	=== 3.3.7 Set Interrupt Mode ===
14.45	705
11.1	706
43.1	707	Feature, Set Interrupt mode for PA8 of pin.
1.1	708
46.1	709	When AT+INTMOD=0 is set, PA8 is used as a digital input port.
	710
1.1	711	(% style="color:blue" %)AT Command: AT+INTMOD
	712
76.15	713	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.1	714	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 192px; background-color: rgb(79, 129, 189); color: white;" %)Function\|=(% style="width: 161px; background-color: rgb(79, 129, 189); color: white;" %)Response
	715	\|(% style="width:154px" %)AT+INTMOD=?\|(% style="width:192px" %)Show current interrupt mode\|(% style="width:161px" %)(((
1.1	716	0
	717	OK
	718	the mode is 0 =Disable Interrupt
	719	)))
87.1	720	\|(% style="width:154px" %)AT+INTMOD=2\|(% style="width:192px" %)(((
	721	0: Disable Interrupt
	722	1: Trigger by rising and falling edge
	723	2: Trigger by falling edge
	724	3: Trigger by rising edge
	725	)))\|(% style="width:161px" %)OK
1.1	726
	727	(% style="color:blue" %)Downlink Command: 0x06
	728
	729	Format: Command Code (0x06) followed by 3 bytes.
	730
	731	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	732
	733	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	734	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	735
44.2	736	=== 3.3.8 Set Power Output Duration ===
41.1	737
	738
	739	Control the output duration 5V . Before each sampling, device will
	740
	741	~1. first enable the power output to external sensor,
	742
	743	2. keep it on as per duration, read sensor value and construct uplink payload
	744
	745	3. final, close the power output.
	746
	747	(% style="color:blue" %)AT Command: AT+5VT
	748
76.15	749	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
76.2	750	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
41.1	751	\|(% style="width:154px" %)AT+5VT=?\|(% style="width:196px" %)Show 5V open time.\|(% style="width:157px" %)0 (default)
	752	OK
64.1	753	\|(% style="width:154px" %)AT+5VT=1000\|(% style="width:196px" %)Close after a delay of 1000 milliseconds.\|(% style="width:157px" %)OK
41.1	754
	755	(% style="color:blue" %)Downlink Command: 0x07
	756
	757	Format: Command Code (0x07) followed by 2 bytes.
	758
	759	The first and second bytes are the time to turn on.
	760
	761	* Example 1: Downlink Payload: 070000 ~-~--> AT+5VT=0
	762	* Example 2: Downlink Payload: 0701F4 ~-~--> AT+5VT=500
	763
78.1	764	=== 3.3.9 Print data entries base on page ===
	765
	766
	767	Feature: Print the sector data from start page to stop page (max is 416 pages).
	768
	769	(% style="color:#4f81bd" %)AT Command: AT+PDTA
	770
	771	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
	772	\|(% style="background-color:#4f81bd; color:white; width:158px" %)Command Example\|(% style="background-color:#4f81bd; color:white; width:352px" %)Function
	773	\|(% style="width:156px" %)(((
	774	AT+PDTA=1,3
	775	Print page 1 to 3
	776	)))\|(% style="width:311px" %)(((
	777	8019500 19/6/26 16:48 1 2992 sht temp=28.21 sht hum=71.5 ds temp=27.31
	778	8019510 19/6/26 16:53 1 2994 sht temp=27.64 sht hum=69.3 ds temp=26.93
	779	8019520 19/6/26 16:58 1 2996 sht temp=28.39 sht hum=72.0 ds temp=27.06
	780	8019530 19/6/26 17:03 1 2996 sht temp=27.97 sht hum=70.4 ds temp=27.12
	781	8019540 19/6/26 17:08 1 2996 sht temp=27.80 sht hum=72.9 ds temp=27.06
	782	8019550 19/6/26 17:13 1 2998 sht temp=27.30 sht hum=72.4 ds temp=26.68
	783	8019560 19/6/26 17:22 1 2992 sht temp=26.27 sht hum=62.3 ds temp=26.56
	784	8019570
	785	8019580
	786	8019590
	787	80195A0
	788	80195B0
	789	80195C0
	790	80195D0
	791	80195E0
	792	80195F0
	793
	794	OK
	795	)))
	796
	797	(% style="color:#4f81bd" %)Downlink Command:
	798
	799	No downlink commands for feature
	800
	801
	802	=== 3.3.10 Print last few data entries ===
	803
	804
	805	Feature: Print the last few data entries
	806
	807	(% style="color:#4f81bd" %)AT Command: AT+PLDTA
	808
	809	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
	810	\|(% style="background-color:#4f81bd; color:white; width:158px" %)Command Example\|(% style="background-color:#4f81bd; color:white; width:352px" %)Function
	811	\|(% style="width:156px" %)(((
	812	AT+PLDTA=5
	813	Print last 5 entries
	814	)))\|(% style="width:311px" %)(((
	815	Stop Tx and RTP events when read sensor data
	816	1 19/6/26 13:59 1 3005 sht temp=27.09 sht hum=79.5 ds temp=26.75
	817	2 19/6/26 14:04 1 3007 sht temp=26.65 sht hum=74.8 ds temp=26.43
	818	3 19/6/26 14:09 1 3007 sht temp=26.91 sht hum=77.9 ds temp=26.56
	819	4 19/6/26 14:15 1 3007 sht temp=26.93 sht hum=76.7 ds temp=26.75
	820	5 19/6/26 14:20 1 3007 sht temp=26.78 sht hum=76.6 ds temp=26.43
	821	Start Tx and RTP events
	822	OK
	823	)))
	824
	825	(% style="color:#4f81bd" %)Downlink Command:
	826
	827	No downlink commands for feature
	828
	829
79.1	830	=== 3.3.11 Clear Flash Record ===
78.1	831
	832
	833	Feature: Clear flash storage for data log feature.
	834
	835	(% style="color:#4f81bd" %)AT Command: AT+CLRDTA
	836
	837	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:503px" %)
	838	\|(% style="background-color:#4f81bd; color:white; width:157px" %)Command Example\|(% style="background-color:#4f81bd; color:white; width:137px" %)Function\|(% style="background-color:#4f81bd; color:white; width:209px" %)Response
	839	\|(% style="width:155px" %)AT+CLRDTA \|(% style="width:134px" %)Clear date record\|(% style="width:209px" %)(((
	840	Clear all stored sensor data…
	841
	842	OK
	843	)))
	844
	845	(% style="color:#4f81bd" %)Downlink Command: 0xA3
	846
	847	* Example: 0xA301 ~/~/ Same as AT+CLRDTA
	848
16.4	849	= 4. Battery & Power Consumption =
14.45	850
1.1	851
73.4	852	S31x-LB use ER26500 + SPC1520 battery pack and S31x-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
1.1	853
	854	[[Battery Info & Power Consumption Analyze>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
	855
	856
16.4	857	= 5. OTA Firmware update =
1.1	858
	859
13.1	860	(% class="wikigeneratedid" %)
73.4	861	User can change firmware S31x-LB/LS to:
1.1	862
13.1	863	* Change Frequency band/ region.
	864	* Update with new features.
	865	* Fix bugs.
1.1	866
63.2	867	Firmware and changelog can be downloaded from : [[Firmware download link>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]
1.1	868
	869
31.1	870	Methods to Update Firmware:
1.1	871
64.2	872	* (Recommanded way) OTA firmware update via wireless : [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	873	* Update through UART TTL interface : [[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]].
1.1	874
31.1	875	= 6. FAQ =
1.1	876
	877
	878
31.1	879	= 7. Order Info =
1.1	880
	881
73.5	882	Part Number: (% style="color:blue" %)S31-LB-XX / S31B-LB-XX(%%) or (% style="color:blue" %)S31-LS-XX / S31B-LS-XX(%%)
1.1	883
38.1	884	(% style="color:red" %)XX(%%): The default frequency band
1.1	885
38.1	886	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
1.1	887
38.1	888	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
1.1	889
38.1	890	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
1.1	891
38.1	892	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
1.1	893
38.1	894	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
1.1	895
38.1	896	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
1.1	897
38.1	898	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
1.1	899
38.1	900	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
1.1	901
31.1	902	= 8. Packing Info =
1.1	903
39.6	904
39.1	905	(% style="color:#037691" %)Package Includes:
1.1	906
73.4	907	* S31x-LB or S31x-LS LoRaWAN Temperature & Humidity Sensor
1.1	908
39.1	909	(% style="color:#037691" %)Dimension and weight:
1.1	910
31.1	911	* Device Size: cm
1.1	912
31.1	913	* Device Weight: g
1.1	914
31.1	915	* Package Size / pcs : cm
1.1	916
31.1	917	* Weight / pcs : g
1.1	918
31.1	919	= 9. Support =
1.1	920
	921
31.1	922	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
39.6	923
	924	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].

Wiki source code of S31/S31B-LB/LS -- LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

Applications