Last modified by Xiaoling on 2023/09/19 09:20
<
From version < 162.2 >
edited by Xiaoling
on 2023/06/05 15:32
To version < 146.4 >
edited by Xiaoling
on 2022/08/16 14:24
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -8,6 +8,7 @@
8 8  
9 9  = 1.  LA66 LoRaWAN Module =
10 10  
11 +
11 11  == 1.1  What is LA66 LoRaWAN Module ==
12 12  
13 13  
... ... @@ -48,6 +48,7 @@
48 48  )))
49 49  
50 50  
52 +
51 51  == 1.2  Features ==
52 52  
53 53  
... ... @@ -61,6 +61,8 @@
61 61  * Firmware upgradable via UART interface
62 62  * Ultra-long RF range
63 63  
66 +
67 +
64 64  == 1.3  Specification ==
65 65  
66 66  
... ... @@ -82,12 +82,15 @@
82 82  * LoRa Rx current: <9 mA
83 83  * I/O Voltage: 3.3v
84 84  
89 +
90 +
85 85  == 1.4  AT Command ==
86 86  
87 87  
88 -AT Command is valid over Main TXD and Main RXD. Serial Baud Rate is 9600. AT commands can be found in[[ AT Command documents>>https://www.dropbox.com/sh/wtq43za8sykpgta/AABAEE02uEAsRU-JV7bzEhMba?dl=0]].
94 +AT Command is valid over Main TXD and Main RXD. Serial Baud Rate is 9600. AT commands can be found in AT Command documents.
89 89  
90 90  
97 +
91 91  == 1.5  Dimension ==
92 92  
93 93  
... ... @@ -94,11 +94,13 @@
94 94  [[image:image-20220718094750-3.png]]
95 95  
96 96  
104 +
97 97  == 1.6  Pin Mapping ==
98 98  
99 99  [[image:image-20220720111850-1.png]]
100 100  
101 101  
110 +
102 102  == 1.7  Land Pattern ==
103 103  
104 104  
... ... @@ -105,112 +105,23 @@
105 105  [[image:image-20220517072821-2.png]]
106 106  
107 107  
117 +
108 108  = 2.  FAQ =
109 109  
110 -== 2.1  Where to find examples of how to use LA66? ==
111 111  
121 +== 2.1  How to Compile Source Code for LA66? ==
112 112  
113 -(% class="wikigeneratedid" %)
114 -Below products are made by LA66. User can use their examples as reference:
115 115  
116 -* [[LA66 Shield for Arduino>>doc:Main.User Manual for LoRaWAN End Nodes.LA66 LoRaWAN Shield User Manual.WebHome]]
117 -* [[LA66 USB Adapter>>doc:Main.User Manual for LoRaWAN End Nodes.LA66 USB LoRaWAN Adapter User Manual.WebHome]]
124 +Compile and Upload Code to ASR6601 Platform ：[[Instruction>>Compile and Upload Code to ASR6601 Platform]]
118 118  
119 -== 2.2  How to Compile Source Code for LA66? ==
120 120  
121 121  
122 -Compile and Upload Code to ASR6601 Platform：[[Instruction>>Compile and Upload Code to ASR6601 Platform]]
123 -
124 -
125 -== 2.3  Can i use LA66 module's internal I/O without external MCU, So to save product cost? ==
126 -
127 -
128 -Yes, this is possible, user can refer[[ the source code from ASR >>https://github.com/asrlora/asr_lora_6601/tree/master/projects/ASR6601SE-EVAL/examples/lora]]to get examples for how to its I/O Interfaces.
129 -
130 -
131 -== 2.4  Where to find Peer-to-Peer firmware of LA66? ==
132 -
133 -
134 -Instruction for LA66 Peer to Peer firmware :[[ Instruction >>doc:Main.User Manual for LoRaWAN End Nodes.LA66 LoRaWAN Shield User Manual.Instruction for LA66 Peer to Peer firmware.WebHome]]
135 -
136 -
137 -== 2.5 How can i use J-LInk to debug LA66? ==
138 -
139 -
140 -(% style="color:#037691" %)**The steps are as follows:**
141 -
142 -
143 -(% style="color:blue" %)**1. Install J-Link software from**
144 -
145 -[[https:~~/~~/www.segger.com/downloads/jlink/>>url:https://www.segger.com/downloads/jlink/]]
146 -
147 -
148 -(% style="color:blue" %)**2. Expose PA6 / PA7 / RSTN of LA66.**
149 -
150 -
151 -[[image:image-20230605151850-1.png]]
152 -
153 -
154 -[[image:image-20230605151850-2.png]]
155 -
156 -
157 -(% style="color:blue" %)**3. Connect JLINK, and switch mother board SW1 to ISP. Wire connection as below:**
158 -
159 -**LA66 PA6 < ~-~- > JLINK SWDIO (Pin 7)**
160 -
161 -**LA66 PA7 < ~-~- > JLINK SWCLK (Pin 9)**
162 -
163 -**LA66 RSTN < ~-~- > JLINK RESET (Pin 15)**
164 -
165 -**LA66 GND  < ~-~- > JLINK GND (Pin 8)**
166 -
167 -[[image:image-20230605151850-3.png||height="629" width="1182"]]
168 -
169 -(% style="display:none" %) (%%)
170 -
171 -(% style="color:blue" %)**4. Copy \SN50v3\tools\FLM\ASR6601.FLM to \Keil\ARM\ Flash\**
172 -
173 -(% style="display:none" %) [[image:image-20230605151850-4.png]]
174 -
175 -
176 -(% style="color:blue" %)**Add ASR6601 256KB Flash to Flash Download**
177 -
178 -[[image:image-20230605152412-12.png]]
179 -
180 -
181 -[[image:image-20230605151851-6.png]]
182 -
183 -
184 -(% style="color:blue" %)**5. Modify \SN50v3\Projects\Applications\DRAGINO-LRWAN-AT\cfg\gcc.ld, to 0x08000000.**
185 -
186 -[[image:image-20230605151851-7.png]]
187 -
188 -[[image:image-20230605151851-8.png]]
189 -
190 -
191 -(% style="color:red" %)Note**: After debug, user should change the Flash address back to 0x0800D000, and upload the OTA bootloader to LA66. Otherwise, the compiled program doesn’t support OTA update.**
192 -
193 -
194 -(% style="color:blue" %)**6. Comment the low power function in main.c.**
195 -
196 -
197 -[[image:image-20230605151851-9.png]]
198 -
199 -
200 -(% style="color:blue" %)**Click Debug mode to debug.**
201 -
202 -[[image:image-20230605151851-10.png||height="293" width="1275"]]
203 -
204 -
205 -[[image:image-20230605151851-11.png||height="739" width="1275"]](% style="display:none" %)
206 -
207 -(% style="display:none" %) (%%)
208 -
209 209  = 3.  Order Info =
210 210  
211 211  
212 212  **Part Number:**  (% style="color:blue" %)**LA66-XXX**
213 213  
133 +
214 214  (% style="color:blue" %)**XXX**(%%): The default frequency band
215 215  
216 216  * (% style="color:red" %)**AS923**(%%):  LoRaWAN AS923 band
... ... @@ -223,31 +223,5 @@
223 223  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
224 224  * (% style="color:red" %)**PP**(%%):  Peer to Peer LoRa Protocol
225 225  
226 -= 4.  FCC Statement =
227 227  
228 -
229 -(% style="color:red" %)**FCC Caution:**
230 -
231 -Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
232 -
233 -This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
234 -
235 -
236 -(% style="color:red" %)**IMPORTANT NOTE: **
237 -
238 -(% style="color:red" %)**Note:**(%%) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
239 -
240 -—Reorient or relocate the receiving antenna.
241 -
242 -—Increase the separation between the equipment and receiver.
243 -
244 -—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
245 -
246 -—Consult the dealer or an experienced radio/TV technician for help.
247 -
248 -
249 -(% style="color:red" %)**FCC Radiation Exposure Statement: **
250 -
251 -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
252 -
253 253  
image-20230605151850-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -532.8 KB
Content
image-20230605151850-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -534.2 KB
Content
image-20230605151850-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -2.3 MB
Content
image-20230605151850-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -42.7 KB
Content
image-20230605151851-10.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -64.0 KB
Content
image-20230605151851-11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.3 KB
Content
image-20230605151851-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -67.2 KB
Content
image-20230605151851-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -43.3 KB
Content
image-20230605151851-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -26.3 KB
Content
image-20230605151851-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -12.9 KB
Content
image-20230605151851-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -12.2 KB
Content
image-20230605152412-12.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -60.2 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0