Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -64,7 +64,6 @@
64	64	* Ultra-long RF range
65	65
66	66
67		-
68	68	== 1.3  Specification ==
69	69
70	70
...	...	@@ -87,11 +87,10 @@
87	87	* I/O Voltage: 3.3v
88	88
89	89
90		-
91	91	== 1.4  AT Command ==
92	92
93	93
94		-AT Command is valid over Main TXD and Main RXD. Serial Baud Rate is 9600. AT commands can be found in AT Command documents.
	92	+AT Command is valid over Main TXD and Main RXD. Serial Baud Rate is 9600. AT commands can be found in[[ AT Command documents>>https://www.dropbox.com/sh/wtq43za8sykpgta/AABAEE02uEAsRU-JV7bzEhMba?dl=0]].
95	95
96	96
97	97
...	...	@@ -121,10 +121,24 @@
121	121	== 2.1  How to Compile Source Code for LA66? ==
122	122
123	123
124		-Compile and Upload Code to ASR6601 Platform ：[[Instruction>>Compile and Upload Code to ASR6601 Platform]]
	122	+Compile and Upload Code to ASR6601 Platform：[[Instruction>>Compile and Upload Code to ASR6601 Platform]]
125	125
126	126
127	127
	126	+== 2.2 Can i use LA66 module's internal I/O without external MCU, So to save product cost? ==
	127	+
	128	+
	129	+Yes, this is possible, user can refer[[ the source code from ASR >>https://github.com/asrlora/asr_lora_6601/tree/master/projects/ASR6601SE-EVAL/examples/lora]]to get examples for how to its I/O Interfaces.
	130	+
	131	+
	132	+
	133	+== 2.3  Where to find Peer-to-Peer firmware of LA66? ==
	134	+
	135	+
	136	+Instruction for LA66 Peer to Peer firmware :[[ Instruction >>doc:Main.User Manual for LoRaWAN End Nodes.LA66 LoRaWAN Shield User Manual.Instruction for LA66 Peer to Peer firmware.WebHome]]
	137	+
	138	+
	139	+
128	128	= 3.  Order Info =
129	129
130	130
...	...	@@ -144,4 +144,37 @@
144	144	* (% style="color:red" %)**PP**(%%):  Peer to Peer LoRa Protocol
145	145
146	146
147		-
	159	+
	160	+= 4.  FCC Statement =
	161	+
	162	+
	163	+**(% style="color:red" %)FCC Caution:**
	164	+
	165	+
	166	+Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
	167	+
	168	+
	169	+This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
	170	+
	171	+
	172	+**(% style="color:red" %)IMPORTANT NOTE: **
	173	+
	174	+
	175	+Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
	176	+
	177	+
	178	+—Reorient or relocate the receiving antenna.
	179	+
	180	+
	181	+—Increase the separation between the equipment and receiver.
	182	+
	183	+
	184	+—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
	185	+
	186	+
	187	+—Consult the dealer or an experienced radio/TV technician for help.
	188	+
	189	+
	190	+**(% style="color:red" %)FCC Radiation Exposure Statement: **
	191	+
	192	+This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.