Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20220613175511-8.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.David
	1	+XWiki.Edwin

Content

...	...	@@ -120,12 +120,12 @@
120	120
121	121	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652927365661-475.png?width=723&height=359&rev=1.1||alt="1652927365661-475.png" height="359" width="723"]]
122	122
123		-Please check the decoder from this link:
	123	+Please check the decoder [gropoint_Decoder_V1.0.0.js] from this link:
124	124
125		-[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/Decoder/>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/Decoder/]]
	125	+[[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
126	126
127	127
128		-= Show data on Datacake =
	128	+== Show data on Datacake ==
129	129
130	130	Datacake IoT platform provides a human-friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:
131	131
...	...	@@ -133,16 +133,22 @@
133	133
134	134	**Step 2**: Configure SW3L in Datacake  ​​​​
135	135
	136	+[[image:image-20220613171007-1.png||height="567" width="542"]]
136	136
	138	+[[image:image-20220613171015-2.png||height="600" width="586"]]
137	137
	140	+[[image:image-20220613171029-3.png||height="507" width="513"]]
138	138
	142	+[[image:image-20220613171038-4.png||height="469" width="786"]]
139	139
	144	+[[image:image-20220613171105-5.png||height="533" width="949"]]
140	140
	146	+[[image:image-20220613171117-6.png||height="501" width="925"]]
141	141
	148	+[[image:image-20220613171124-7.png||height="466" width="877"]]
142	142
143	143
144	144
145		-
146	146	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
147	147
148	148	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
...	...	@@ -204,8 +204,27 @@
204	204	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
205	205	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
206	206
207		-== 3.3 Get Firmware Version Info ==
	213	+== (% id="cke_bm_55968S" style="display:none" %) (%%)3.3 Set the sensor delay time ==
208	208
	215	+Feature: Change the sensor delay time.
	216	+
	217	+The default delay is 1000ms.
	218	+
	219	+**AT Command: AT+SDELAY**
	220	+
	221	+[[image:image-20220613175511-8.png]]
	222	+
	223	+**Downlink Command: 0xA1**
	224	+
	225	+Format: Command Code (0xA1) followed by 3 bytes time value.
	226	+
	227	+If the downlink payload=A10007D0, it means set the sensor delay time to 0x0007D0=2000ms, while type code is A1.
	228	+
	229	+* Example 1: Downlink Payload: A10003E8 ~/~/ Set the sensor delay time = 1000ms
	230	+* Example 2: Downlink Payload: A10007D0 ~/~/ Set the sensor delay time = 2000ms
	231	+
	232	+== 3.4 Get Firmware Version Info ==
	233	+
209	209	Feature: use downlink to get firmware version.
210	210
211	211	**Downlink Command: 0x26**
...	...	@@ -421,5 +421,3 @@
421	421	* Device Weight: g
422	422	* Package Size / pcs : cm
423	423	* Weight / pcs : g
424		-
425		-

image-20220613175511-8.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.David

Size

...	...	@@ -1,0 +1,1 @@
	1	+15.7 KB

Content