Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20220613175511-8.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.David
	1	+XWiki.Edwin

Content

...	...	@@ -120,9 +120,9 @@
120	120
121	121	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652927365661-475.png?width=723&height=359&rev=1.1||alt="1652927365661-475.png" height="359" width="723"]]
122	122
123		-Please check the decoder from this link:
	123	+Please check the decoder [gropoint_Decoder_V1.0.0.js] from this link:
124	124
125		-[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/Decoder/>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/Decoder/]]
	125	+[[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
126	126
127	127
128	128	= Show data on Datacake =
...	...	@@ -133,16 +133,22 @@
133	133
134	134	**Step 2**: Configure SW3L in Datacake  ​​​​
135	135
	136	+[[image:image-20220613171007-1.png||height="567" width="542"]]
136	136
	138	+[[image:image-20220613171015-2.png||height="600" width="586"]]
137	137
	140	+[[image:image-20220613171029-3.png||height="507" width="513"]]
138	138
	142	+[[image:image-20220613171038-4.png||height="469" width="786"]]
139	139
	144	+[[image:image-20220613171105-5.png||height="533" width="949"]]
140	140
	146	+[[image:image-20220613171117-6.png||height="501" width="925"]]
141	141
	148	+[[image:image-20220613171124-7.png||height="466" width="877"]]
142	142
143	143
144	144
145		-
146	146	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
147	147
148	148	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
...	...	@@ -204,8 +204,27 @@
204	204	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
205	205	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
206	206
207		-== 3.3 Get Firmware Version Info ==
	213	+== (% id="cke_bm_55968S" style="display:none" %) (%%)3.3 Set the sensor delay time ==
208	208
	215	+Feature: Change the sensor delay time.
	216	+
	217	+The default delay is 1000ms.
	218	+
	219	+**AT Command: AT+SDELAY**
	220	+
	221	+[[image:image-20220613175511-8.png]]
	222	+
	223	+**Downlink Command: 0xA1**
	224	+
	225	+Format: Command Code (0xA1) followed by 3 bytes time value.
	226	+
	227	+If the downlink payload=A10007D0, it means set the sensor delay time to 0x0007D0=2000ms, while type code is A1.
	228	+
	229	+* Example 1: Downlink Payload: A10003E8 ~/~/ Set the sensor delay time = 1000ms
	230	+* Example 2: Downlink Payload: A10007D0 ~/~/ Set the sensor delay time = 2000ms
	231	+
	232	+== 3.4 Get Firmware Version Info ==
	233	+
209	209	Feature: use downlink to get firmware version.
210	210
211	211	**Downlink Command: 0x26**
...	...	@@ -421,5 +421,3 @@
421	421	* Device Weight: g
422	422	* Package Size / pcs : cm
423	423	* Weight / pcs : g
424		-
425		-

image-20220613175511-8.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.David

Size

...	...	@@ -1,0 +1,1 @@
	1	+15.7 KB

Content