Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.David
	1	+XWiki.Edwin

Content

...	...	@@ -54,24 +54,6 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
57		-= Connect LoRaWAN Network =
58		-
59		-
60		-== LED Indicator ==
61		-
62		-The GroPoint Air has an internal LED which can show the status of different states.
63		-
64		-* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
65		-* Blink once when device transmits a packet.
66		-
67		-== Firmware and Changelog ==
68		-
69		-Firmware Download Location: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/]]
70		-
71		-Change Log:
72		-
73		-
74		-
75	75	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
76	76
77	77	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
...	...	@@ -87,8 +87,12 @@
87	87
88	88	These commands are to configure:
89	89
90		-* General system settings like: uplink interval.
91		-* LoRaWAN protocol & radio-related command.
	72	+* (((
	73	+General system settings like: uplink interval.
	74	+)))
	75	+* (((
	76	+LoRaWAN protocol & radio-related command.
	77	+)))
92	92
93	93	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
94	94
...	...	@@ -113,11 +113,17 @@
113	113
114	114	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
115	115
116		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
117		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	102	+* (((
	103	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	104	+)))
	105	+* (((
	106	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
118	118
119		-== 3.2 Set Interrupt Mode ==
	108	+
	109	+)))
120	120
	111	+== 3.2 Set Interrupt Mode  （是否存在） ==
	112	+
121	121	Feature, Set Interrupt mode for GPIO_EXIT.
122	122
123	123	**AT Command: AT+INTMOD**
...	...	@@ -130,10 +130,14 @@
130	130
131	131	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
132	132
133		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
134		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	125	+* (((
	126	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	127	+)))
	128	+* (((
	129	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	130	+)))
135	135
136		-== 3.3 Get Firmware Version Info ==
	132	+== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
137	137
138	138	Feature: use downlink to get firmware version.
139	139
...	...	@@ -150,7 +150,7 @@
150	150
151	151	|=(((
152	152	**Size(bytes)**
153		-)))|=**1**|=**1**|=**1**|=**2**|=**1**|=4|=**1**
	149	+)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
154	154	|**Value**|Software Type|(((
155	155	Frequency
156	156
...	...	@@ -186,10 +186,8 @@
186	186
187	187	*0x09: AS923-2
188	188
189		-*0x0A: AS923-3
	185	+*0xa0: AS923-3
190	190
191		-*0x0B: AS923-4
192		-
193	193	**Sub-Band**: value 0x00 ~~ 0x08
194	194
195	195	**Firmware Version**: 0x0100, Means: v1.0.0 version
...	...	@@ -208,9 +208,7 @@
208	208
209	209	0x06: LSNPK01
210	210
211		-0x07: LDDS45
212	212
213		-0x08: LSLP01
214	214
215	215	= Use AT Command =
216	216