Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -54,32 +54,18 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
57		-= Connect LoRaWAN Network =
58		-
59		-
60		-== LED Indicator  ( 检查等状态是否对的) ==
61		-
62		-The GroPoint Air has an internal LED which can show the status of different states.
63		-
64		-* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
65		-* Blink once when device transmits a packet.
66		-
67		-== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
68		-
69		-Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
70		-
71		-Change Log:
72		-
73		-
74		-
75	75	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
76	76
77	77	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
78	78
79		-* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
80		-* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
	61	+* (((
	62	+AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
	63	+)))
	64	+* (((
	65	+LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
	66	+)))
81	81
82		-There are two kinds of commands to configure GroPoint Air, they are:
	68	+There are two kinds of commands to configure GroPoint, they are:
83	83
84	84	* (((
85	85	**~ General Commands**.
...	...	@@ -87,17 +87,21 @@
87	87
88	88	These commands are to configure:
89	89
90		-* General system settings like: uplink interval.
91		-* LoRaWAN protocol & radio-related command.
	76	+* (((
	77	+General system settings like: uplink interval.
	78	+)))
	79	+* (((
	80	+LoRaWAN protocol & radio-related command.
	81	+)))
92	92
93	93	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
94	94
95	95
96	96	* (((
97		-**~ Commands special design for GroPoint Air**
	87	+**~ Commands special design for LLMS01**
98	98	)))
99	99
100		-These commands only valid for GroPoint Air, as below:
	90	+These commands only valid for LLMS01, as below:
101	101
102	102	== 3.1 Set Transmit Interval Time ==
103	103
...	...	@@ -113,9 +113,15 @@
113	113
114	114	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
115	115
116		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
117		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	106	+* (((
	107	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	108	+)))
	109	+* (((
	110	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
118	118
	112	+
	113	+)))
	114	+
119	119	== 3.2 Set Interrupt Mode  （是否存在） ==
120	120
121	121	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -130,9 +130,14 @@
130	130
131	131	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
132	132
133		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
134		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	129	+* (((
	130	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	131	+)))
	132	+* (((
	133	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	134	+)))
135	135
	136	+
136	136	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
137	137
138	138	Feature: use downlink to get firmware version.