Changes for page GroPoint Air-M -- LoRaWAN Multi Segment Soil Sensor Converter User Manual

Last modified by Xiaoling on 2025/04/25 10:03

From version < 40.1 >

edited by Edwin Chen
on 2022/06/09 00:01

To version < 28.1 >

edited by Edwin Chen
on 2022/06/08 23:45

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -54,160 +54,6 @@
  [[image:image-20220530002453-3.png||height="262" width="493"]]
--= Connect LoRaWAN Network =
--
--
--== LED Indicator  ( 检查等状态是否对的) ==
--
--The GroPoint Air has an internal LED which can show the status of different states.
--
--* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
--* Blink once when device transmits a packet.
--
--== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
--
--Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
--
--Change Log:
--
--
--
--= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
--
--Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
--
--* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
--* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
--
--There are two kinds of commands to configure GroPoint Air, they are:
--
--* (((
--**~ General Commands**.
--)))
--
--These commands are to configure:
--
--* General system settings like: uplink interval.
--* LoRaWAN protocol & radio-related command.
--
--They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--
--
--* (((
--**~ Commands special design for GroPoint Air**
--)))
--
--These commands only valid for GroPoint Air, as below:
--
--== 3.1 Set Transmit Interval Time ==
--
--Feature: Change LoRaWAN End Node Transmit Interval.
--
--**AT Command: AT+TDC**
--
--[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171554-8.png?rev=1.1||alt="image-20220607171554-8.png"]]
--
--**Downlink Command: 0x01**
--
--Format: Command Code (0x01) followed by 3 bytes time value.
--
--If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
--
--* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
--* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--== 3.2 Set Interrupt Mode  （是否存在） ==
--
--Feature, Set Interrupt mode for GPIO_EXIT.
--
--**AT Command: AT+INTMOD**
--
--[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171716-9.png?rev=1.1||alt="image-20220607171716-9.png"]]
--
--**Downlink Command: 0x06**
--
--Format: Command Code (0x06) followed by 3 bytes.
--
--This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
--
--* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
--* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
--
--== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
--
--Feature: use downlink to get firmware version.
--
--**Downlink Command: 0x26**
--
--[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171917-10.png?rev=1.1||alt="image-20220607171917-10.png"]]
--
--* Reply to the confirmation package: 26 01
--* Reply to non-confirmed packet: 26 00
--
--Device will send an uplink after got this downlink command. With below payload:
--
--Configures info payload:
--
--|=(((
--**Size(bytes)**
--)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
--|**Value**|Software Type|(((
--Frequency
--
--Band
--)))|Sub-band|(((
--Firmware
--
--Version
--)))|Sensor Type|Reserve|(((
--[[Message Type>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H2.3.6MessageType]]
--Always 0x02
--)))
--
--**Software Type**: Always 0x03 for LLMS01
--
--**Frequency Band**:
--
--*0x01: EU868
--
--*0x02: US915
--
--*0x03: IN865
--
--*0x04: AU915
--
--*0x05: KZ865
--
--*0x06: RU864
--
--*0x07: AS923
--
--*0x08: AS923-1
--
--*0x09: AS923-2
--
--*0xa0: AS923-3
--
--**Sub-Band**: value 0x00 ~~ 0x08
--
--**Firmware Version**: 0x0100, Means: v1.0.0 version
--
--**Sensor Type**:
--
--0x01: LSE01
--
--0x02: LDDS75
--
--0x03: LDDS20
--
--0x04: LLMS01
--
--0x05: LSPH01
--
--0x06: LSNPK01
--
--
--
  = Use AT Command =
  == Access AT Commands ==
@@ -247,7 +247,16 @@
  GroPoint Air:  2.45v ~~ 3.6v
++==   ==
++== Replace Battery ==
++
++Any battery with a range 2.45 ~~ 3.6v can be a replacement. We recommend using Li-SOCl2 Battery.
++
++And make sure the positive and negative pins match.
++
++==   ==
++
  == Power Consumption Analyze ==
  Dragino Battery-powered products are all runs in Low Power mode. We have an updated battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit intervals.
@@ -270,7 +270,7 @@
  Working Mode
  )))
--And the Life expectation in different cases will be shown on the right.
++And the Life expectation in difference case will be shown on the right.
  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/1654593605679-189.png?rev=1.1||alt="1654593605679-189.png"]]
@@ -288,21 +288,20 @@
  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607172042-11.png?rev=1.1||alt="image-20220607172042-11.png"]]
++=== 4.3.1 Battery Note ===
--=== Battery Note ===
++The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
--The Li-SICO battery is designed for small current / long period applications. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period to transmit LoRa, then the battery life may be decreased.
++=== 4.3.2 Replace the battery ===
++You can change the battery in the LLMS01.The type of battery is not limited as long as the output is between 3v to 3.6v.  On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
--=== Replace the battery ===
++The default battery pack of LLMS01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
--You can change the battery in GroPoint Air. The type of battery is not limited as long as the output is between 3v to 3.6v.
--The default battery pack of GroPoint Air includes a ER26500 plus supercapacitor. If users can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most cases. The SPC can enlarge the battery life for high-frequency use (update period below 5 minutes)
--
  = FAQ =
  == How to change the LoRa Frequency Bands/Region ==

Changes for page GroPoint Air-M -- LoRaWAN Multi Segment Soil Sensor Converter User Manual

Summary

Details

Applications

Navigation