Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -54,31 +54,18 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
57		-== LED Indicator  ( 检查等状态是否对的) ==
58		-
59		-The GroPoint Air has an internal LED which can show the status of different states.
60		-
61		-* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
62		-* Blink once when device transmits a packet.
63		-
64		-
65		-
66		-== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
67		-
68		-Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
69		-
70		-Change Log:
71		-
72		-
73		-
74	74	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
75	75
76	76	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
77	77
78		-* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
79		-* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
	61	+* (((
	62	+AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
	63	+)))
	64	+* (((
	65	+LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
	66	+)))
80	80
81		-There are two kinds of commands to configure GroPoint Air, they are:
	68	+There are two kinds of commands to configure GroPoint, they are:
82	82
83	83	* (((
84	84	**~ General Commands**.
...	...	@@ -86,17 +86,21 @@
86	86
87	87	These commands are to configure:
88	88
89		-* General system settings like: uplink interval.
90		-* LoRaWAN protocol & radio-related command.
	76	+* (((
	77	+General system settings like: uplink interval.
	78	+)))
	79	+* (((
	80	+LoRaWAN protocol & radio-related command.
	81	+)))
91	91
92	92	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
93	93
94	94
95	95	* (((
96		-**~ Commands special design for GroPoint Air**
	87	+**~ Commands special design for LLMS01**
97	97	)))
98	98
99		-These commands only valid for GroPoint Air, as below:
	90	+These commands only valid for LLMS01, as below:
100	100
101	101	== 3.1 Set Transmit Interval Time ==
102	102
...	...	@@ -112,9 +112,15 @@
112	112
113	113	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
114	114
115		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
116		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	106	+* (((
	107	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	108	+)))
	109	+* (((
	110	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
117	117
	112	+
	113	+)))
	114	+
118	118	== 3.2 Set Interrupt Mode  （是否存在） ==
119	119
120	120	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -129,9 +129,14 @@
129	129
130	130	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
131	131
132		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
133		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	129	+* (((
	130	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	131	+)))
	132	+* (((
	133	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	134	+)))
134	134
	136	+
135	135	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
136	136
137	137	Feature: use downlink to get firmware version.