Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -54,6 +54,15 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
	57	+
	58	+== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
	59	+
	60	+Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
	61	+
	62	+Change Log:
	63	+
	64	+
	65	+
57	57	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
58	58
59	59	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
...	...	@@ -69,12 +69,8 @@
69	69
70	70	These commands are to configure:
71	71
72		-* (((
73		-General system settings like: uplink interval.
74		-)))
75		-* (((
76		-LoRaWAN protocol & radio-related command.
77		-)))
	81	+* General system settings like: uplink interval.
	82	+* LoRaWAN protocol & radio-related command.
78	78
79	79	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
80	80
...	...	@@ -99,15 +99,9 @@
99	99
100	100	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
101	101
102		-* (((
103		-Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
104		-)))
105		-* (((
106		-Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	107	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	108	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
107	107
108		-
109		-)))
110		-
111	111	== 3.2 Set Interrupt Mode  （是否存在） ==
112	112
113	113	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -122,12 +122,8 @@
122	122
123	123	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
124	124
125		-* (((
126		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
127		-)))
128		-* (((
129		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
130		-)))
	124	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	125	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
131	131
132	132	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
133	133