Last modified by Xiaoling on 2025/04/25 10:03
<
From version < 33.1 >
edited by Edwin Chen
on 2022/06/08 23:53
To version < 29.1 >
edited by Edwin Chen
on 2022/06/08 23:46
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -54,156 +54,6 @@
54 54  [[image:image-20220530002453-3.png||height="262" width="493"]]
55 55  
56 56  
57 -= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
58 -
59 -Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
60 -
61 -* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
62 -* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
63 -
64 -There are two kinds of commands to configure GroPoint, they are:
65 -
66 -* (((
67 -**~ General Commands**.
68 -)))
69 -
70 -These commands are to configure:
71 -
72 -* (((
73 -General system settings like: uplink interval.
74 -)))
75 -* (((
76 -LoRaWAN protocol & radio-related command.
77 -)))
78 -
79 -They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
80 -
81 -
82 -* (((
83 -**~ Commands special design for LLMS01**
84 -)))
85 -
86 -These commands only valid for LLMS01, as below:
87 -
88 -== 3.1 Set Transmit Interval Time ==
89 -
90 -Feature: Change LoRaWAN End Node Transmit Interval.
91 -
92 -**AT Command: AT+TDC**
93 -
94 -[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171554-8.png?rev=1.1||alt="image-20220607171554-8.png"]]
95 -
96 -**Downlink Command: 0x01**
97 -
98 -Format: Command Code (0x01) followed by 3 bytes time value.
99 -
100 -If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
101 -
102 -* (((
103 -Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
104 -)))
105 -* (((
106 -Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
107 -
108 -
109 -)))
110 -
111 -== 3.2 Set Interrupt Mode  （是否存在） ==
112 -
113 -Feature, Set Interrupt mode for GPIO_EXIT.
114 -
115 -**AT Command: AT+INTMOD**
116 -
117 -[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171716-9.png?rev=1.1||alt="image-20220607171716-9.png"]]
118 -
119 -**Downlink Command: 0x06**
120 -
121 -Format: Command Code (0x06) followed by 3 bytes.
122 -
123 -This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
124 -
125 -* (((
126 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
127 -)))
128 -* (((
129 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
130 -)))
131 -
132 -== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
133 -
134 -Feature: use downlink to get firmware version.
135 -
136 -**Downlink Command: 0x26**
137 -
138 -[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171917-10.png?rev=1.1||alt="image-20220607171917-10.png"]]
139 -
140 -* Reply to the confirmation package: 26 01
141 -* Reply to non-confirmed packet: 26 00
142 -
143 -Device will send an uplink after got this downlink command. With below payload:
144 -
145 -Configures info payload:
146 -
147 -|=(((
148 -**Size(bytes)**
149 -)))|=**1**|=**1**|=**1**|=**1**|=**1**|=**5**|=**1**
150 -|**Value**|Software Type|(((
151 -Frequency
152 -
153 -Band
154 -)))|Sub-band|(((
155 -Firmware
156 -
157 -Version
158 -)))|Sensor Type|Reserve|(((
159 -[[Message Type>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H2.3.6MessageType]]
160 -Always 0x02
161 -)))
162 -
163 -**Software Type**: Always 0x03 for LLMS01
164 -
165 -**Frequency Band**:
166 -
167 -*0x01: EU868
168 -
169 -*0x02: US915
170 -
171 -*0x03: IN865
172 -
173 -*0x04: AU915
174 -
175 -*0x05: KZ865
176 -
177 -*0x06: RU864
178 -
179 -*0x07: AS923
180 -
181 -*0x08: AS923-1
182 -
183 -*0x09: AS923-2
184 -
185 -*0xa0: AS923-3
186 -
187 -**Sub-Band**: value 0x00 ~~ 0x08
188 -
189 -**Firmware Version**: 0x0100, Means: v1.0.0 version
190 -
191 -**Sensor Type**:
192 -
193 -0x01: LSE01
194 -
195 -0x02: LDDS75
196 -
197 -0x03: LDDS20
198 -
199 -0x04: LLMS01
200 -
201 -0x05: LSPH01
202 -
203 -0x06: LSNPK01
204 -
205 -
206 -
207 207  = Use AT Command =
208 208  
209 209  == Access AT Commands ==
... ... @@ -243,6 +243,7 @@
243 243  
244 244  GroPoint Air:  2.45v ~~ 3.6v
245 245  
96 +== ==
246 246  
247 247  == Power Consumption Analyze ==
248 248  
... ... @@ -266,7 +266,7 @@
266 266  Working Mode
267 267  )))
268 268  
269 -And the Life expectation in different cases will be shown on the right.
120 +And the Life expectation in difference case will be shown on the right.
270 270  
271 271  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/1654593605679-189.png?rev=1.1||alt="1654593605679-189.png"]]
272 272  
... ... @@ -284,21 +284,26 @@
284 284  
285 285  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607172042-11.png?rev=1.1||alt="image-20220607172042-11.png"]]
286 286  
138 +(% class="wikigeneratedid" %)
139 +=== ===
287 287  
288 288  === ​Battery Note ===
289 289  
290 -The Li-SICO battery is designed for small current / long period applications. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period to transmit LoRa, then the battery life may be decreased.
143 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
291 291  
145 +(% class="wikigeneratedid" %)
146 +=== ===
292 292  
293 293  === Replace the battery ===
294 294  
295 -You can change the battery in GroPoint Air. The type of battery is not limited as long as the output is between 3v to 3.6v.
150 +You can change the battery in the LLMS01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
296 296  
297 -The default battery pack of GroPoint Air includes a ER26500 plus supercapacitor. If users can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most cases. The SPC can enlarge the battery life for high-frequency use (update period below 5 minutes)
152 +The default battery pack of LLMS01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
298 298  
299 299  
300 300  
301 301  
157 +
302 302  = FAQ =
303 303  
304 304  == How to change the LoRa Frequency Bands/Region ==

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0