Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -58,14 +58,10 @@
58	58
59	59	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
60	60
61		-* (((
62		-AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
63		-)))
64		-* (((
65		-LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
66		-)))
	61	+* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
	62	+* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
67	67
68		-There are two kinds of commands to configure GroPoint, they are:
	64	+There are two kinds of commands to configure GroPoint Air, they are:
69	69
70	70	* (((
71	71	**~ General Commands**.
...	...	@@ -73,21 +73,17 @@
73	73
74	74	These commands are to configure:
75	75
76		-* (((
77		-General system settings like: uplink interval.
78		-)))
79		-* (((
80		-LoRaWAN protocol & radio-related command.
81		-)))
	72	+* General system settings like: uplink interval.
	73	+* LoRaWAN protocol & radio-related command.
82	82
83	83	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
84	84
85	85
86	86	* (((
87		-**~ Commands special design for LLMS01**
	79	+**~ Commands special design for GroPoint Air**
88	88	)))
89	89
90		-These commands only valid for LLMS01, as below:
	82	+These commands only valid for GroPoint Air, as below:
91	91
92	92	== 3.1 Set Transmit Interval Time ==
93	93
...	...	@@ -103,14 +103,9 @@
103	103
104	104	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
105	105
106		-* (((
107		-Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
108		-)))
109		-* (((
110		-Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	98	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	99	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
111	111
112		-
113		-)))
114	114
115	115	== 3.2 Set Interrupt Mode  （是否存在） ==
116	116
...	...	@@ -126,12 +126,8 @@
126	126
127	127	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
128	128
129		-* (((
130		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
131		-)))
132		-* (((
133		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
134		-)))
	116	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	117	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
135	135
136	136
137	137	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==