Last modified by Xiaoling on 2024/04/23 14:37
<
From version < 28.1 >
edited by Edwin Chen
on 2022/06/08 23:45
To version < 41.1 >
edited by David Huang
on 2022/06/11 16:36
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.David
Content
... ... @@ -54,6 +54,164 @@
54 54  [[image:image-20220530002453-3.png||height="262" width="493"]]
55 55  
56 56  
57 += Connect LoRaWAN Network =
58 +
59 +
60 +== LED Indicator ==
61 +
62 +The GroPoint Air has an internal LED which can show the status of different states.
63 +
64 +* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
65 +* Blink once when device transmits a packet.
66 +
67 +== Firmware and Changelog ==
68 +
69 +Firmware Download Location: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/]]
70 +
71 +Change Log:
72 +
73 +
74 +
75 += Configure GroPoint Air via AT Command or LoRaWAN Downlink =
76 +
77 +Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
78 +
79 +* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
80 +* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
81 +
82 +There are two kinds of commands to configure GroPoint Air, they are:
83 +
84 +* (((
85 +**~ General Commands**.
86 +)))
87 +
88 +These commands are to configure:
89 +
90 +* General system settings like: uplink interval.
91 +* LoRaWAN protocol & radio-related command.
92 +
93 +They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
94 +
95 +
96 +* (((
97 +**~ Commands special design for GroPoint Air**
98 +)))
99 +
100 +These commands only valid for GroPoint Air, as below:
101 +
102 +== 3.1 Set Transmit Interval Time ==
103 +
104 +Feature: Change LoRaWAN End Node Transmit Interval.
105 +
106 +**AT Command: AT+TDC**
107 +
108 +[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171554-8.png?rev=1.1||alt="image-20220607171554-8.png"]]
109 +
110 +**Downlink Command: 0x01**
111 +
112 +Format: Command Code (0x01) followed by 3 bytes time value.
113 +
114 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
115 +
116 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
117 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
118 +
119 +== 3.2 Set Interrupt Mode ==
120 +
121 +Feature, Set Interrupt mode for GPIO_EXIT.
122 +
123 +**AT Command: AT+INTMOD**
124 +
125 +[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171716-9.png?rev=1.1||alt="image-20220607171716-9.png"]]
126 +
127 +**Downlink Command: 0x06**
128 +
129 +Format: Command Code (0x06) followed by 3 bytes.
130 +
131 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
132 +
133 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
134 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
135 +
136 +== 3.3 Get Firmware Version Info ==
137 +
138 +Feature: use downlink to get firmware version.
139 +
140 +**Downlink Command: 0x26**
141 +
142 +[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607171917-10.png?rev=1.1||alt="image-20220607171917-10.png"]]
143 +
144 +* Reply to the confirmation package: 26 01
145 +* Reply to non-confirmed packet: 26 00
146 +
147 +Device will send an uplink after got this downlink command. With below payload:
148 +
149 +Configures info payload:
150 +
151 +|=(((
152 +**Size(bytes)**
153 +)))|=**1**|=**1**|=**1**|=**2**|=**1**|=4|=**1**
154 +|**Value**|Software Type|(((
155 +Frequency
156 +
157 +Band
158 +)))|Sub-band|(((
159 +Firmware
160 +
161 +Version
162 +)))|Sensor Type|Reserve|(((
163 +[[Message Type>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H2.3.6MessageType]]
164 +Always 0x02
165 +)))
166 +
167 +**Software Type**: Always 0x03 for LLMS01
168 +
169 +**Frequency Band**:
170 +
171 +*0x01: EU868
172 +
173 +*0x02: US915
174 +
175 +*0x03: IN865
176 +
177 +*0x04: AU915
178 +
179 +*0x05: KZ865
180 +
181 +*0x06: RU864
182 +
183 +*0x07: AS923
184 +
185 +*0x08: AS923-1
186 +
187 +*0x09: AS923-2
188 +
189 +*0x0A: AS923-3
190 +
191 +*0x0B: AS923-4
192 +
193 +**Sub-Band**: value 0x00 ~~ 0x08
194 +
195 +**Firmware Version**: 0x0100, Means: v1.0.0 version
196 +
197 +**Sensor Type**:
198 +
199 +0x01: LSE01
200 +
201 +0x02: LDDS75
202 +
203 +0x03: LDDS20
204 +
205 +0x04: LLMS01
206 +
207 +0x05: LSPH01
208 +
209 +0x06: LSNPK01
210 +
211 +0x07: LDDS45
212 +
213 +0x08: LSLP01
214 +
57 57  = Use AT Command =
58 58  
59 59  == Access AT Commands ==
... ... @@ -93,16 +93,7 @@
93 93  
94 94  GroPoint Air:  2.45v ~~ 3.6v
95 95  
96 -== ==
97 97  
98 -== Replace Battery ==
99 -
100 -Any battery with a range 2.45 ~~ 3.6v can be a replacement. We recommend using Li-SOCl2 Battery.
101 -
102 -And make sure the positive and negative pins match.
103 -
104 -== ==
105 -
106 106  == Power Consumption Analyze ==
107 107  
108 108  Dragino Battery-powered products are all runs in Low Power mode. We have an updated battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit intervals.
... ... @@ -125,7 +125,7 @@
125 125  Working Mode
126 126  )))
127 127  
128 -And the Life expectation in difference case will be shown on the right.
277 +And the Life expectation in different cases will be shown on the right.
129 129  
130 130  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/1654593605679-189.png?rev=1.1||alt="1654593605679-189.png"]]
131 131  
... ... @@ -143,20 +143,21 @@
143 143  
144 144  [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/WebHome/image-20220607172042-11.png?rev=1.1||alt="image-20220607172042-11.png"]]
145 145  
146 -=== 4.3.1 ​Battery Note ===
147 147  
148 -The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
296 +=== ​Battery Note ===
149 149  
150 -=== ​4.3.2 Replace the battery ===
298 +The Li-SICO battery is designed for small current / long period applications. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period to transmit LoRa, then the battery life may be decreased.
151 151  
152 -You can change the battery in the LLMS01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
153 153  
154 -The default battery pack of LLMS01 includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
301 +=== Replace the battery ===
155 155  
303 +You can change the battery in GroPoint Air. The type of battery is not limited as long as the output is between 3v to 3.6v.
156 156  
305 +The default battery pack of GroPoint Air includes a ER26500 plus supercapacitor. If users can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most cases. The SPC can enlarge the battery life for high-frequency use (update period below 5 minutes)
157 157  
158 158  
159 159  
309 +
160 160  = FAQ =
161 161  
162 162  == How to change the LoRa Frequency Bands/Region ==

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0