Wiki source code of S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

Version 60.9 by Xiaoling on 2023/05/27 11:03

version	line-number	content
26.1	1	(% style="text-align:center" %)
	2	[[image:S31-B.jpg]]
1.1	3
	4
26.1	5
1.1	6
31.2	7	Table of Contents：
30.1	8
1.1	9	{{toc/}}
	10
	11
	12
	13
	14
	15
31.1	16	= 1. Introduction =
1.1	17
31.1	18	== 1.1 What is S31x-LB LoRaWAN Temperature & Humidity Sensor ==
1.1	19
39.6	20
35.1	21	The Dragino S31x-LB is a (% style="color:blue" %)LoRaWAN Temperature and Humidity Sensor(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)surrounding environment temperature and relative air humidity precisely(%%), and then upload to IoT server via LoRaWAN wireless protocol.
1.1	22
35.1	23	The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)waterproof anti-condensation casing(%%) for long term use.
1.1	24
2.1	25	The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
1.1	26
35.1	27	S31x-LB supports (% style="color:blue" %)Temperature & Humdity alarm feature(%%), user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
1.1	28
35.1	29	S31x-LB (% style="color:blue" %)supports BLE configure(%%) and (% style="color:blue" %)wireless OTA update(%%) which make user easy to use.
1.1	30
35.1	31	S31x-LB is powered by (% style="color:blue" %)8500mAh Li-SOCI2 battery(%%), it is designed for long term use up to 5 years.
1.1	32
2.1	33	Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
1.1	34
	35
	36	== 1.2 Features ==
	37
39.6	38
1.1	39	* LoRaWAN 1.0.3 Class A
	40	* Ultra-low power consumption
5.1	41	* External 3 meters SHT31 probe (For S31-LB)
1.1	42	* Measure range -55°C ~~ 125°C
5.1	43	* Temperature & Humidity alarm
1.1	44	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	45	* Support Bluetooth v5.1 and LoRaWAN remote configure
	46	* Support wireless OTA update firmware
	47	* Uplink on periodically
	48	* Downlink to change configure
	49	* 8500mAh Battery for long term use
	50
	51	== 1.3 Specification ==
	52
	53
	54	(% style="color:#037691" %)Common DC Characteristics:
	55
	56	* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
	57	* Operating Temperature: -40 ~~ 85°C
	58
	59	(% style="color:#037691" %)Temperature Sensor:
	60
5.1	61	* Range: -40 to + 80°C
	62	* Accuracy: ±0.2 @ 0-90 °C
	63	* Resolution: 0.1°C
	64	* Long Term Shift: <0.03 °C/yr
1.1	65
5.1	66	(% style="color:#037691" %)Humidity Sensor:
	67
	68	* Range: 0 ~~ 99.9% RH
	69	* Accuracy: ± 2%RH ( 0 ~~ 100%RH)
	70	* Resolution: 0.01% RH
	71	* Long Term Shift: <0.25 %RH/yr
	72
1.1	73	(% style="color:#037691" %)LoRa Spec:
	74
	75	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	76	* Max +22 dBm constant RF output vs.
	77	* RX sensitivity: down to -139 dBm.
	78	* Excellent blocking immunity
	79
	80	(% style="color:#037691" %)Battery:
	81
	82	* Li/SOCI2 un-chargeable battery
	83	* Capacity: 8500mAh
	84	* Self-Discharge: <1% / Year @ 25°C
	85	* Max continuously current: 130mA
	86	* Max boost current: 2A, 1 second
	87
	88	(% style="color:#037691" %)Power Consumption
	89
	90	* Sleep Mode: 5uA @ 3.3v
	91	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	92
	93	== 1.4 Sleep mode and working mode ==
	94
	95
	96	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
	97
	98	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
	99
	100
	101	== 1.5 Button & LEDs ==
	102
	103
6.1	104	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
1.1	105
	106
14.13	107	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
14.11	108	\|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)Behavior on ACT\|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)Function\|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)Action
1.1	109	\|(% style="width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="width:117px" %)Send an uplink\|(% style="width:225px" %)(((
	110	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
	111	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	112	)))
	113	\|(% style="width:167px" %)Pressing ACT for more than 3s\|(% style="width:117px" %)Active Device\|(% style="width:225px" %)(((
	114	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	115	(% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	116	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	117	)))
6.1	118	\|(% style="width:167px" %)Fast press ACT 5 times.\|(% style="width:117px" %)Deactivate Device\|(% style="width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
1.1	119
	120	== 1.6 BLE connection ==
	121
	122
16.3	123	S31x-LB support BLE remote configure.
1.1	124
	125
	126	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	127
	128	* Press button to send an uplink
	129	* Press button to active device.
	130	* Device Power on or reset.
	131
	132	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	133
	134
43.1	135	== 1.7 Pin Definitions ==
1.1	136
43.1	137	[[image:image-20230523174230-1.png]]
1.1	138
43.1	139
45.2	140	== 1.8 Hardware Variant ==
43.1	141
	142
58.4	143	(% border="1" cellspacing="5" style="width:510px" %)
14.36	144	\|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model\|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo\|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info
44.1	145	\|(% style="width:102px" %)(((
	146	S31-LB
60.2	147	)))\|(% style="width:190px" %)[[image:image-20230527093214-2.jpeg]]\|(% style="width:297px" %)(((
6.1	148	1 x SHT31 Probe
1.1	149
	150	Cable Length : 2 meters
	151
	152
	153	)))
44.1	154	\|(% style="width:102px" %)(((
	155	S31B-LB
60.2	156	)))\|(% style="width:190px" %)[[image:image-20230527093155-1.jpeg]]\|(% style="width:297px" %)(((
6.1	157	1 x SHT31 Probe
1.1	158
6.1	159	Installed in device.
1.1	160	)))
	161
	162	(% style="display:none" %)
	163
	164
	165
43.1	166	== 1.9 Mechanical ==
1.1	167
	168
6.1	169	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
1.1	170
	171
6.1	172	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
1.1	173
	174
6.1	175	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
1.1	176
	177
6.1	178	= 2. Configure S31x-LB to connect to LoRaWAN network =
1.1	179
	180	== 2.1 How it works ==
	181
	182
6.1	183	The S31x-LB is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
1.1	184
	185
	186	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
	187
	188
	189	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	190
	191	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	192
	193
6.1	194	(% style="color:blue" %)Step 1:(%%) Create a device in TTN with the OTAA keys from S31x-LB.
1.1	195
6.1	196	Each S31x-LB is shipped with a sticker with the default device EUI as below:
1.1	197
30.1	198	[[image:image-20230426084152-1.png\|\|alt="图片-20230426084152-1.png" height="233" width="502"]]
1.1	199
	200
	201	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	202
	203
	204	(% style="color:blue" %)Register the device
	205
14.13	206	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1\|\|alt="1654935135620-998.png"]]
1.1	207
	208
	209	(% style="color:blue" %)Add APP EUI and DEV EUI
	210
30.1	211	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1\|\|alt="图片-20220611161308-4.png"]]
1.1	212
	213
	214	(% style="color:blue" %)Add APP EUI in the application
	215
	216
30.1	217	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1\|\|alt="图片-20220611161308-5.png"]]
1.1	218
	219
	220	(% style="color:blue" %)Add APP KEY
	221
30.1	222	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1\|\|alt="图片-20220611161308-6.png"]]
1.1	223
	224
6.1	225	(% style="color:blue" %)Step 2:(%%) Activate on S31x-LB
1.1	226
	227
6.1	228	Press the button for 5 seconds to activate the S31x-LB.
	229
1.1	230	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	231
	232	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	233
	234
	235	== 2.3 Uplink Payload ==
	236
	237	=== 2.3.1 Device Status, FPORT~=5 ===
	238
	239
16.5	240	Users can use the downlink command(0x26 01) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
1.1	241
	242	The Payload format is as below.
	243
	244
14.15	245	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
	246	\|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)Device Status (FPORT=5)
1.1	247	\|(% style="width:103px" %)Size (bytes)\|(% style="width:72px" %)1\|2\|(% style="width:91px" %)1\|(% style="width:86px" %)1\|(% style="width:44px" %)2
	248	\|(% style="width:103px" %)Value\|(% style="width:72px" %)Sensor Model\|Firmware Version\|(% style="width:91px" %)Frequency Band\|(% style="width:86px" %)Sub-band\|(% style="width:44px" %)BAT
	249
	250	Example parse in TTNv3
	251
58.2	252	[[image:image-20230524144422-1.png\|\|height="174" width="1080"]]
1.1	253
	254
6.1	255	(% style="color:#037691" %)Sensor Model(%%): For S31x-LB, this value is 0x0A
1.1	256
	257	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
	258
	259	(% style="color:#037691" %)Frequency Band:
	260
	261	*0x01: EU868
	262
	263	*0x02: US915
	264
	265	*0x03: IN865
	266
	267	*0x04: AU915
	268
	269	*0x05: KZ865
	270
	271	*0x06: RU864
	272
	273	*0x07: AS923
	274
	275	*0x08: AS923-1
	276
	277	*0x09: AS923-2
	278
	279	*0x0a: AS923-3
	280
	281	*0x0b: CN470
	282
	283	*0x0c: EU433
	284
	285	*0x0d: KR920
	286
	287	*0x0e: MA869
	288
	289
	290	(% style="color:#037691" %)Sub-Band:
	291
	292	AU915 and US915:value 0x00 ~~ 0x08
	293
	294	CN470: value 0x0B ~~ 0x0C
	295
	296	Other Bands: Always 0x00
	297
	298
	299	(% style="color:#037691" %)Battery Info:
	300
	301	Check the battery voltage.
	302
	303	Ex1: 0x0B45 = 2885mV
	304
	305	Ex2: 0x0B49 = 2889mV
	306
	307
	308	=== 2.3.2 Sensor Data. FPORT~=2 ===
	309
	310
7.1	311	Sensor Data is uplink via FPORT=2
1.1	312
60.7	313	(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
60.4	314	\|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
7.1	315	Size(bytes)
60.5	316	)))\|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2\|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4\|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1\|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2\|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
60.8	317	\|(% style="width:99px" %)Value\|(% style="width:69px" %)(((
55.5	318	Battery
14.15	319	)))\|(% style="width:130px" %)(((
55.5	320	Unix TimeStamp
46.1	321	)))\|(% style="width:194px" %)(((
60.3	322	Alarm Flag & MOD& Level of PA8
46.1	323	)))\|(% style="width:106px" %)(((
55.5	324	Temperature
46.1	325	)))\|(% style="width:97px" %)(((
55.5	326	Humidity
7.1	327	)))
1.1	328
58.2	329	[[image:image-20230524144456-2.png\|\|height="180" width="1142"]]
58.1	330
	331
51.1	332	==== (% style="color:#4472c4" %)Battery(%%) ====
1.1	333
	334	Sensor Battery Level.
	335
	336	Ex1: 0x0B45 = 2885mV
	337
	338	Ex2: 0x0B49 = 2889mV
	339
	340
	341
51.1	342	==== (% style="color:#4472c4" %)Temperature(%%) ====
1.1	343
	344	Example:
	345
	346	If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
	347
	348	If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
	349
	350	（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
	351
	352
51.1	353	==== (% style="color:#4472c4" %)Humidity(%%) ====
1.1	354
	355
7.1	356	Read:0x(0197)=412 Value: 412 / 10=41.2, So 41.2%
1.1	357
	358
55.1	359	==== (% style="color:#4472c4" %)Alarm Flag & MOD & Level of PA8(%%) ====
1.1	360
	361
	362	Example:
	363
46.1	364	If payload & 0x01 = 0x01 ~-~-> This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
1.1	365
46.1	366	If payload & 0x01 = 0x00 ~-~-> This is a normal uplink message, no alarm.
1.1	367
46.1	368	If payload & 0x80>>7 = 0x01 ~-~-> The PA8 is low level.
1.1	369
46.1	370	If payload & 0x80>>7 =0x00 ~-~-> The PA8 is high level.
	371
	372	If payload >> 2 = 0x00 ~-~-> means MOD=1, This is a sampling uplink message.
	373
8.1	374	If payload >> 2 = 0x31 ~-~-> means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail.
1.1	375
	376
	377	== 2.4 Payload Decoder file ==
	378
14.22	379
10.1	380	In TTN, use can add a custom payload so it shows friendly reading
1.1	381
10.1	382	In the page (% style="color:#037691" %)Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder(%%) to add the decoder from:
1.1	383
40.1	384	[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
1.1	385
10.1	386
1.1	387	== 2.5 Datalog Feature ==
	388
	389
11.1	390	Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
1.1	391
	392
	393	=== 2.5.1 Ways to get datalog via LoRaWAN ===
	394
	395
39.4	396	Set [[PNACKMD=1>>\|\|anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
1.1	397
44.1	398	* (((
	399	a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
	400	)))
	401	* (((
	402	b) S31x-LB will send data in CONFIRMED Mode when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
	403	)))
1.1	404
	405	Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
	406
30.1	407	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1\|\|alt="图片-20220703111700-2.png" height="381" width="1119"]]
1.1	408
39.5	409
1.1	410	=== 2.5.2 Unix TimeStamp ===
	411
	412
11.1	413	S31x-LB uses Unix TimeStamp format based on
1.1	414
30.1	415	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1\|\|alt="图片-20220523001219-11.png" height="97" width="627"]]
1.1	416
	417	User can get this time from link: [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
	418
	419	Below is the converter example
	420
30.1	421	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1\|\|alt="图片-20220523001219-12.png" height="298" width="720"]]
1.1	422
39.5	423
1.1	424	So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
	425
	426
	427	=== 2.5.3 Set Device Time ===
	428
	429
14.24	430	User need to set (% style="color:blue" %)SYNCMOD=1(%%) to enable sync time via MAC command.
1.1	431
18.1	432	Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
1.1	433
14.24	434	(% style="color:red" %)Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.
1.1	435
	436
11.1	437	=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
1.1	438
	439
11.1	440	The Datalog uplinks will use below payload format.
1.1	441
	442	Retrieval data payload:
	443
60.9	444	(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
	445	\|=(% style="width: 60px;background-color:#D9E2F3" %)(((
1.1	446	Size(bytes)
60.9	447	)))\|=(% style="width: 68px; background-color:#D9E2F3;color:#0070C0" %)2\|=(% style="width: 104px; background-color:#D9E2F3;color:#0070C0" %)2\|=(% style="width: 87px; background-color:#D9E2F3;color:#0070C0" %)2\|=(% style="width: 178px; background-color:#D9E2F3;color:#0070C0" %)1\|=(% style="width: 137px; background-color:#D9E2F3;color:#0070C0" %)4
46.1	448	\|(% style="width:103px" %)Value\|(% style="width:68px" %)(((
	449	ignore
	450	)))\|(% style="width:104px" %)(((
55.1	451	(((
	452	Humidity
	453	)))
	454
	455	(((
	456
	457	)))
	458	)))\|(% style="width:87px" %)(((
46.1	459	Temperature
55.1	460	)))\|(% style="width:178px" %)(((
46.1	461	Poll message flag &
1.1	462
46.1	463	Alarm Flag&
1.1	464
55.1	465	Level of PA8
46.1	466	)))\|(% style="width:137px" %)Unix Time Stamp
	467
55.1	468	Poll message flag & Alarm Flag & Level of PA8:
46.1	469
55.1	470	[[image:image-20230524114302-1.png\|\|height="115" width="736"]]
1.1	471
55.1	472
14.25	473	No ACK Message: 1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for PNACKMD=1 feature)
1.1	474
	475	Poll Message Flag: 1: This message is a poll message reply.
	476
	477	* Poll Message Flag is set to 1.
	478
	479	* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
	480
	481	For example, in US915 band, the max payload for different DR is:
	482
	483	a) DR0: max is 11 bytes so one entry of data
	484
	485	b) DR1: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
	486
	487	c) DR2: total payload includes 11 entries of data
	488
	489	d) DR3: total payload includes 22 entries of data.
	490
	491	If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0
	492
	493	Example:
	494
16.5	495	If S31x-LB has below data inside Flash:
1.1	496
55.1	497	[[image:image-20230524114654-2.png]]
1.1	498
	499
55.1	500	If user sends below downlink command: 31646D84E1646D856C05
1.1	501
55.1	502	Where : Start time: 646D84E1 = time 23/5/24 03:30:41
1.1	503
55.1	504	Stop time: 646D856C= time 23/5/24 03:33:00
14.26	505
55.1	506
16.5	507	S31x-LB will uplink this payload.
1.1	508
58.2	509	[[image:image-20230524114826-3.png\|\|height="448" width="1244"]]
1.1	510
14.44	511	(((
55.1	512	00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
14.44	513	)))
1.1	514
14.44	515	(((
1.1	516	Where the first 11 bytes is for the first entry:
14.44	517	)))
1.1	518
14.44	519	(((
55.1	520	00 00 02 36 01 10 40 64 6D 84 E1
14.44	521	)))
1.1	522
14.44	523	(((
55.1	524	Hum=0x0236/10=56.6
14.44	525	)))
1.1	526
14.44	527	(((
55.1	528	Temp=0x0110/10=27.2
14.44	529	)))
1.1	530
14.44	531	(((
55.1	532	poll message flag & Alarm Flag & Level of PA8=0x40,means reply data,sampling uplink message,the PA8 is low level.
14.44	533	)))
1.1	534
14.44	535	(((
55.1	536	Unix time is 0x646D84E1=1684899041s=23/5/24 03:30:41
14.44	537	)))
1.1	538
	539
30.1	540	(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==\|\|alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
1.1	541
	542	== 2.6 Temperature Alarm Feature ==
	543
	544
11.1	545	S31x-LB work flow with Alarm feature.
1.1	546
	547
51.1	548	[[image:image-20230524110125-3.png\|\|height="768" width="1115"]]
1.1	549
	550
51.1	551
1.1	552	== 2.7 Frequency Plans ==
	553
	554
11.1	555	The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
1.1	556
	557	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
	558
	559
11.1	560	= 3. Configure S31x-LB =
1.1	561
16.4	562	== 3.1 Configure Methods ==
1.1	563
	564
11.1	565	S31x-LB supports below configure method:
1.1	566
	567	* AT Command via Bluetooth Connection (Recommended): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
11.1	568	* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
1.1	569	* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
	570
	571	== 3.2 General Commands ==
	572
	573
	574	These commands are to configure:
	575
	576	* General system settings like: uplink interval.
	577	* LoRaWAN protocol & radio related command.
	578
	579	They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	580
	581	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	582
	583
11.1	584	== 3.3 Commands special design for S31x-LB ==
1.1	585
	586
11.1	587	These commands only valid for S31x-LB, as below:
1.1	588
	589
	590	=== 3.3.1 Set Transmit Interval Time ===
	591
	592
	593	Feature: Change LoRaWAN End Node Transmit Interval.
	594
	595	(% style="color:blue" %)AT Command: AT+TDC
	596
14.34	597	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
14.27	598	\|=(% style="width: 156px;background-color:#D9E2F3" %)Command Example\|=(% style="width: 137px;background-color:#D9E2F3" %)Function\|=(% style="background-color:#D9E2F3" %)Response
1.1	599	\|(% style="width:156px" %)AT+TDC=?\|(% style="width:137px" %)Show current transmit Interval\|(((
	600	30000
	601	OK
	602	the interval is 30000ms = 30s
	603	)))
	604	\|(% style="width:156px" %)AT+TDC=60000\|(% style="width:137px" %)Set Transmit Interval\|(((
	605	OK
	606	Set transmit interval to 60000ms = 60 seconds
	607	)))
	608
	609	(% style="color:blue" %)Downlink Command: 0x01
	610
	611	Format: Command Code (0x01) followed by 3 bytes time value.
	612
	613	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
	614
	615	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	616	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	617
	618	=== 3.3.2 Get Device Status ===
	619
	620
	621	Send a LoRaWAN downlink to ask device send Alarm settings.
	622
14.31	623	(% style="color:blue" %)Downlink Payload: (%%)0x26 01
1.1	624
	625	Sensor will upload Device Status via FPORT=5. See payload section for detail.
	626
	627
16.4	628	=== 3.3.3 Set Temperature Alarm Threshold ===
1.1	629
39.6	630
14.34	631	* (% style="color:blue" %)AT Command:
1.1	632
14.34	633	(% style="color:#037691" %)AT+SHTEMP=min,max
1.1	634
11.1	635	* When min=0, and max≠0, Alarm higher than max
	636	* When min≠0, and max=0, Alarm lower than min
	637	* When min≠0 and max≠0, Alarm higher than max or lower than min
1.1	638
11.1	639	Example:
1.1	640
11.1	641	AT+SHTEMP=0,30 ~/~/ Alarm when temperature higher than 30.
1.1	642
14.34	643	* (% style="color:blue" %)Downlink Payload:
1.1	644
14.45	645	(% style="color:#037691" %)0x(0C 01 00 1E) (%%) ~/~/ Set AT+SHTEMP=0,30
1.1	646
14.34	647	(% style="color:red" %)(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)
1.1	648
	649
16.4	650	=== 3.3.4 Set Humidity Alarm Threshold ===
1.1	651
39.6	652
14.34	653	* (% style="color:blue" %)AT Command:
1.1	654
14.34	655	(% style="color:#037691" %)AT+SHHUM=min,max
1.1	656
11.1	657	* When min=0, and max≠0, Alarm higher than max
	658	* When min≠0, and max=0, Alarm lower than min
	659	* When min≠0 and max≠0, Alarm higher than max or lower than min
1.1	660
11.1	661	Example:
1.1	662
14.45	663	AT+SHHUM=70,0 ~/~/ Alarm when humidity lower than 70%.
1.1	664
14.34	665	* (% style="color:blue" %)Downlink Payload:
1.1	666
14.45	667	(% style="color:#037691" %)0x(0C 02 46 00)(%%) ~/~/ Set AT+SHTHUM=70,0
1.1	668
14.34	669	(% style="color:red" %)(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))
1.1	670
	671
16.4	672	=== 3.3.5 Set Alarm Interval ===
1.1	673
39.6	674
1.1	675	The shortest time of two Alarm packet. (unit: min)
	676
14.34	677	* (% style="color:blue" %)AT Command:
1.1	678
14.34	679	(% style="color:#037691" %)AT+ATDC=30 (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
1.1	680
14.34	681	* (% style="color:blue" %)Downlink Payload:
1.1	682
14.34	683	(% style="color:#037691" %)0x(0D 00 1E)(%%) ~-~--> Set AT+ATDC=0x 00 1E = 30 minutes
1.1	684
	685
16.4	686	=== 3.3.6 Get Alarm settings ===
1.1	687
	688
	689	Send a LoRaWAN downlink to ask device send Alarm settings.
	690
	691	* (% style="color:#037691" %)Downlink Payload: (%%)0x0E 01
	692
	693	Example:
	694
51.1	695	[[image:image-20230524110211-4.png]]
1.1	696
	697	Explain:
	698
	699	* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
	700
16.4	701	=== 3.3.7 Set Interrupt Mode ===
14.45	702
11.1	703
43.1	704	Feature, Set Interrupt mode for PA8 of pin.
1.1	705
46.1	706	When AT+INTMOD=0 is set, PA8 is used as a digital input port.
	707
1.1	708	(% style="color:blue" %)AT Command: AT+INTMOD
	709
14.34	710	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
14.32	711	\|=(% style="width: 154px;background-color:#D9E2F3" %)Command Example\|=(% style="width: 196px;background-color:#D9E2F3" %)Function\|=(% style="width: 157px;background-color:#D9E2F3" %)Response
1.1	712	\|(% style="width:154px" %)AT+INTMOD=?\|(% style="width:196px" %)Show current interrupt mode\|(% style="width:157px" %)(((
	713	0
	714	OK
	715	the mode is 0 =Disable Interrupt
	716	)))
	717	\|(% style="width:154px" %)AT+INTMOD=2\|(% style="width:196px" %)(((
	718	Set Transmit Interval
	719	0. (Disable Interrupt),
	720	~1. (Trigger by rising and falling edge)
	721	2. (Trigger by falling edge)
	722	3. (Trigger by rising edge)
	723	)))\|(% style="width:157px" %)OK
	724
	725	(% style="color:blue" %)Downlink Command: 0x06
	726
	727	Format: Command Code (0x06) followed by 3 bytes.
	728
	729	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	730
	731	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	732	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	733
44.2	734	=== 3.3.8 Set Power Output Duration ===
41.1	735
	736
	737	Control the output duration 5V . Before each sampling, device will
	738
	739	~1. first enable the power output to external sensor,
	740
	741	2. keep it on as per duration, read sensor value and construct uplink payload
	742
	743	3. final, close the power output.
	744
	745	(% style="color:blue" %)AT Command: AT+5VT
	746
	747	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
	748	\|=(% style="width: 154px;background-color:#D9E2F3" %)Command Example\|=(% style="width: 196px;background-color:#D9E2F3" %)Function\|=(% style="width: 157px;background-color:#D9E2F3" %)Response
	749	\|(% style="width:154px" %)AT+5VT=?\|(% style="width:196px" %)Show 5V open time.\|(% style="width:157px" %)0 (default)
	750	OK
	751	\|(% style="width:154px" %)AT+5VT=500\|(% style="width:196px" %)Close after a delay of 1000 milliseconds.\|(% style="width:157px" %)OK
	752
	753	(% style="color:blue" %)Downlink Command: 0x07
	754
	755	Format: Command Code (0x07) followed by 2 bytes.
	756
	757	The first and second bytes are the time to turn on.
	758
	759	* Example 1: Downlink Payload: 070000 ~-~--> AT+5VT=0
	760	* Example 2: Downlink Payload: 0701F4 ~-~--> AT+5VT=500
	761
16.4	762	= 4. Battery & Power Consumption =
14.45	763
1.1	764
11.1	765	S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
1.1	766
	767	[[Battery Info & Power Consumption Analyze>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
	768
	769
16.4	770	= 5. OTA Firmware update =
1.1	771
	772
13.1	773	(% class="wikigeneratedid" %)
	774	User can change firmware S31x-LB to:
1.1	775
13.1	776	* Change Frequency band/ region.
	777	* Update with new features.
	778	* Fix bugs.
1.1	779
31.1	780	Firmware and changelog can be downloaded from : [[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]
1.1	781
	782
31.1	783	Methods to Update Firmware:
1.1	784
31.1	785	* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
39.6	786	* Update through UART TTL interface. [[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]].
1.1	787
31.1	788	= 6. FAQ =
1.1	789
	790
	791
31.1	792	= 7. Order Info =
1.1	793
	794
39.1	795	Part Number: (% style="color:blue" %)S31-LB-XX / S31B-LB-XX
1.1	796
38.1	797	(% style="color:red" %)XX(%%): The default frequency band
1.1	798
38.1	799	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
1.1	800
38.1	801	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
1.1	802
38.1	803	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
1.1	804
38.1	805	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
1.1	806
38.1	807	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
1.1	808
38.1	809	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
1.1	810
38.1	811	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
1.1	812
38.1	813	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
1.1	814
31.1	815	= 8. Packing Info =
1.1	816
39.6	817
39.1	818	(% style="color:#037691" %)Package Includes:
1.1	819
31.1	820	* S31x-LB LoRaWAN Temperature & Humidity Sensor
1.1	821
39.1	822	(% style="color:#037691" %)Dimension and weight:
1.1	823
31.1	824	* Device Size: cm
1.1	825
31.1	826	* Device Weight: g
1.1	827
31.1	828	* Package Size / pcs : cm
1.1	829
31.1	830	* Weight / pcs : g
1.1	831
31.1	832	= 9. Support =
1.1	833
	834
31.1	835	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
39.6	836
	837	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].

Wiki source code of S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

Applications