Changes for page DS20L -- LoRaWAN Smart Distance Detector User Manual 01

Last modified by Mengting Qiu on 2023/12/14 11:15

From 70.10 to 70.9 From 82.10 to 82.9

From version 82.9

edited by Xiaoling
on 2023/06/14 16:59

Change comment: There is no comment for this version

To version 70.10

edited by Xiaoling
on 2023/06/12 18:03

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 12 removed)

Details

Page properties

Title

@@ -1,1 +1,1 @@
--LDS12-LB -- LoRaWAN LiDAR ToF Distance Sensor User Manual
++DDS75-LB -- LoRaWAN Distance Detection Sensor User Manual

Content

@@ -1,12 +1,9 @@
  (% style="text-align:center" %)
--[[image:image-20230614153353-1.png]]
++[[image:image-20230612170349-1.png||height="656" width="656"]]
--
--
--
  **Table of Contents：**
  {{toc/}}
@@ -18,26 +18,24 @@
  = 1. Introduction =
--== 1.1 What is LoRaWAN LiDAR ToF Distance Sensor ==
++== 1.1 What is LoRaWAN Distance Detection Sensor ==
--The Dragino LDS12-LB is a (% style="color:blue" %)**LoRaWAN LiDAR ToF (Time of Flight) Distance Sensor**(%%) for Internet of Things solution. It is capable to measure the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)!. The LiDAR probe uses laser induction technology for distance measurement.
++The Dragino DDS75-LB is a (% style="color:blue" %)** LoRaWAN Distance Detection Sensor**(%%) for Internet of Things solution. It is used to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses (% style="color:blue" %)** ultrasonic sensing technology**(%%) for (% style="color:blue" %)**distance measurement**(%%), and (% style="color:blue" %)** temperature compensation**(%%) is performed internally to improve the reliability of data. The DDS75-LB can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc.
--The LDS12-LB can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.
++It detects the distance(% style="color:blue" %)**  between the measured object and the sensor**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
--It detects the distance between the measured object and the sensor, and uploads the value via wireless to LoRaWAN IoT Server.
++The LoRa wireless technology used in SW3L-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
--The LoRa wireless technology used in LDS12-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
++SW3L-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
--LDS12-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
++SW3L-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
--LDS12-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
++Each SW3L-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
--Each LDS12-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
++[[image:image-20230612170943-2.png||height="525" width="912"]]
--[[image:image-20230614162334-2.png||height="468" width="800"]]
--
  == 1.2 Features ==
@@ -44,41 +44,52 @@
  * LoRaWAN 1.0.3 Class A
  * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
  * Ultra-low power consumption
--* Laser technology for distance detection
--* Measure Distance: 0.1m~~12m @ 90% Reflectivity
--* Accuracy :  ±5cm@(0.1-6m), ±1%@(6m-12m)
--* Monitor Battery Level
++* Distance Detection by Ultrasonic technology
++* Flat object range 280mm - 7500mm
++* Accuracy: ±(1cm+S*0.3%) (S: Distance)
++* Cable Length : 25cm
  * Support Bluetooth v5.1 and LoRaWAN remote configure
  * Support wireless OTA update firmware
  * AT Commands to change parameters
  * Downlink to change configure
++* IP66 Waterproof Enclosure
  * 8500mAh Battery for long term use
  == 1.3 Specification ==
++(% style="color:#037691" %)**Rated environmental conditions:**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
++|(% style="background-color:#d9e2f3; color:#0070c0; width:163px" %)**Item**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)(((
++**Minimum value**
++)))|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)(((
++**Typical value**
++)))|(% style="background-color:#d9e2f3; color:#0070c0; width:87px" %)(((
++**Maximum value**
++)))|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**Unit**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Remarks**
++|(% style="width:174px" %)Storage temperature|(% style="width:86px" %)-25|(% style="width:66px" %)25|(% style="width:90px" %)80|(% style="width:48px" %)℃|(% style="width:203px" %)
++|(% style="width:174px" %)Storage humidity|(% style="width:86px" %) |(% style="width:66px" %)65%|(% style="width:90px" %)90%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
++|(% style="width:174px" %)Operating temperature|(% style="width:86px" %)-15|(% style="width:66px" %)25|(% style="width:90px" %)60|(% style="width:48px" %)℃|(% style="width:203px" %)
++|(% style="width:174px" %)Working humidity|(% style="width:86px" %)(((
++
++
++
++)))|(% style="width:66px" %)65%|(% style="width:90px" %)80%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
++
++(((
++**Remarks: (1)  a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);       **
++
++**~                       b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
++
++
++)))
++
  (% style="color:#037691" %)**Common DC Characteristics:**
  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
  * Operating Temperature: -40 ~~ 85°C
--(% style="color:#037691" %)**Probe Specification:**
--
--* Storage temperature：-20℃~~75℃
--* Operating temperature : -20℃~~60℃
--* Measure Distance:
--** 0.1m ~~ 12m @ 90% Reflectivity
--** 0.1m ~~ 4m @ 10% Reflectivity
--* Accuracy : ±5cm@(0.1-6m), ±1%@(6m-12m)
--* Distance resolution : 5mm
--* Ambient light immunity : 70klux
--* Enclosure rating : IP65
--* Light source : LED
--* Central wavelength : 850nm
--* FOV : 3.6°
--* Material of enclosure : ABS+PC
--* Wire length : 25cm
--
  (% style="color:#037691" %)**LoRa Spec:**
  * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
@@ -99,11 +99,24 @@
  * Sleep Mode: 5uA @ 3.3v
  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
++== 1.4 Effective measurement range Reference beam pattern ==
--== 1.4 Applications ==
++**~1. The tested object is a white cylindrical tube made of PVC, with a height of 100cm and a diameter of 7.5cm.**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852253176-749.png?rev=1.1||alt="1654852253176-749.png"]]
++
++
++**2. The object to be tested is a "corrugated cardboard box" perpendicular to the central axis of 0 °, and the length * width is 60cm * 50cm.**
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852175653-550.png?rev=1.1||alt="1654852175653-550.png"]]
++
++
++== 1.5 Applications ==
++
++
  * Horizontal distance measurement
++* Liquid level measurement
  * Parking management system
  * Object proximity and presence detection
  * Intelligent trash can management system
@@ -110,19 +110,17 @@
  * Robot obstacle avoidance
  * Automatic control
  * Sewer
++* Bottom water level monitoring
++== 1.6 Sleep mode and working mode ==
--(% style="display:none" %)
--== 1.5 Sleep mode and working mode ==
--
--
  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
--== 1.6 Button & LEDs ==
++== 1.7 Button & LEDs ==
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
@@ -141,11 +141,12 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
--== 1.7 BLE connection ==
++== 1.8 BLE connection ==
--LDS12-LB support BLE remote configure.
++DDS75-LB support BLE remote configure.
++
  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
  * Press button to send an uplink
@@ -155,13 +155,14 @@
  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
--== 1.8 Pin Definitions ==
++== 1.9 Pin Definitions ==
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/WL03A-LB_LoRaWAN_None-Position_Rope_Type_Water_Leak_Controller_User_Manual/WebHome/image-20230613144156-1.png?rev=1.1||alt="image-20230613144156-1.png"]]
++[[image:image-20230523174230-1.png]]
++==   ==
--== 1.9 Mechanical ==
++== 2.10 Mechanical ==
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
@@ -173,19 +173,24 @@
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
--(% style="color:blue" %)**Probe Mechanical:**
++**Probe Mechanical:**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-1.png?rev=1.1||alt="image-20220610172003-1.png"]]
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLDS12-LoRaWAN%20LiDAR%20ToF%20Distance%20Sensor%20User%20Manual/WebHome/1654827224480-952.png?rev=1.1||alt="1654827224480-952.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
--= 2. Configure LDS12-LB to connect to LoRaWAN network =
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
++
++
++= 2. Configure DDS75-LB to connect to LoRaWAN network =
++
  == 2.1 How it works ==
--The LDS12-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the LDS12-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
++The DDS75-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DDS75-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
  (% style="display:none" %) (%%)
@@ -196,12 +196,12 @@
  The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
--[[image:image-20230614162359-3.png||height="468" width="800"]](% style="display:none" %)
++[[image:image-20230612171032-3.png||height="492" width="855"]](% style="display:none" %)
--(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from LDS12-LB.
++(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DDS75-LB.
--Each LDS12-LB is shipped with a sticker with the default device EUI as below:
++Each DDS75-LB is shipped with a sticker with the default device EUI as below:
  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
@@ -230,10 +230,10 @@
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
--(% style="color:blue" %)**Step 2:**(%%) Activate on LDS12-LB
++(% style="color:blue" %)**Step 2:**(%%) Activate on DDS75-LB
--Press the button for 5 seconds to activate the LDS12-LB.
++Press the button for 5 seconds to activate the DDS75-LB.
  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
@@ -240,37 +240,42 @@
  After join success, it will start to upload messages to TTN and you can see the messages in the panel.
--== 2.3 Uplink Payload ==
++== 2.3  Uplink Payload ==
  (((
--LDS12-LB will uplink payload via LoRaWAN with below payload format:
++(((
++DDS75-LB will uplink payload via LoRaWAN with below payload format:
  )))
  (((
--Uplink payload includes in total 11 bytes.
++Uplink payload includes in total 4 bytes.
++Payload for firmware version v1.1.4. . Before v1.1.3, there is on two fields: BAT and Distance
  )))
++)))
++(((
++
++)))
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 62.5px;background-color:#4F81BD;color:white" %)(((
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
  **Size(bytes)**
--)))|=(% style="width: 62.5px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 62.5px;background-color:#4F81BD;color:white" %)**2**|=(% style="background-color:#4F81BD;color:white" %)**2**|=(% style="background-color:#4F81BD;color:white" %)**2**|=(% style="background-color:#4F81BD;color:white" %)**1**|=(% style="background-color:#4F81BD;color:white" %)**1**|=(% style="background-color:#4F81BD;color:white" %)**1**
--|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1BatteryInfo"]]|(% style="width:62.5px" %)(((
--[[Temperature DS18B20>>||anchor="H2.3.2DS18B20Temperaturesensor"]]
--)))|[[Distance>>||anchor="H2.3.3A0Distance"]]|[[Distance signal strength>>||anchor="H2.3.4Distancesignalstrength"]]|(((
--[[Interrupt  flag>>||anchor="H2.3.5InterruptPin"]]
--)))|[[LiDAR temp>>||anchor="H2.3.6LiDARtemp"]]|(((
--[[Message Type>>||anchor="H2.3.7MessageType"]]
--)))
++)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)1|=(% style="background-color:#D9E2F3;color:#0070C0" %)2|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
++|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((
++[[Distance>>||anchor="H2.3.2A0Distance"]]
++(unit: mm)
++)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((
++[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]
++)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLDS12-LoRaWAN%20LiDAR%20ToF%20Distance%20Sensor%20User%20Manual/WebHome/1654833689380-972.png?rev=1.1||alt="1654833689380-972.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850511545-399.png?rev=1.1||alt="1654850511545-399.png"]]
--=== 2.3.1 Battery Info ===
++=== 2.3.1  Battery Info ===
--Check the battery voltage for LDS12-LB.
++Check the battery voltage for DDS75-LB.
  Ex1: 0x0B45 = 2885mV
@@ -277,117 +277,91 @@
  Ex2: 0x0B49 = 2889mV
--=== 2.3.2 DS18B20 Temperature sensor ===
++=== 2.3.2  Distance ===
--This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
++(((
++Get the distance. Flat object range 280mm - 7500mm.
++)))
++(((
++For example, if the data you get from the register is 0x0B 0x05, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
--**Example**:
++(% style="color:#4472c4" %)**0B05(H) = 2821 (D) = 2821 mm.**
++)))
--If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
--If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
++* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
++* If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
++=== 2.3.3  Interrupt Pin ===
--=== 2.3.3 Distance ===
++This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3A0SetInterruptMode"]] for the hardware and software set up.
--Represents the distance value of the measurement output, the default unit is cm, and the value range parsed as a decimal number is 0-1200. In actual use, when the signal strength value Strength.
++**Example:**
++0x00: Normal uplink packet.
--**Example**:
++0x01: Interrupt Uplink Packet.
--If the data you get from the register is 0x0B 0xEA, the distance between the sensor and the measured object is 0BEA(H) = 3050 (D)/10 = 305cm.
++=== 2.3.4  DS18B20 Temperature sensor ===
--=== 2.3.4 Distance signal strength ===
++This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
--Refers to the signal strength, the default output value will be between 0-65535. When the distance measurement gear is fixed, the farther the distance measurement is, the lower the signal strength; the lower the target reflectivity, the lower the signal strength. When Strength is greater than 100 and not equal to 65535, the measured value of Dist is considered credible.
--
--
  **Example**:
--If payload is: 01D7(H)=471(D), distance signal strength=471, 471>100,471≠65535, the measured value of Dist is considered credible.
++If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
--Customers can judge whether they need to adjust the environment based on the signal strength.
++If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
++(% style="color:red" %)**Note: DS18B20 feature is supported in the hardware version > v1.3 which made since early of 2021.**
--=== 2.3.5 Interrupt Pin ===
++=== 2.3.5  Sensor Flag ===
--This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H4.2A0SetInterruptMode"]] for the hardware and software set up.
--Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>||anchor="H1.6A0Pinmappingandpoweron"]].
--
--**Example:**
--
--0x00: Normal uplink packet.
--
--0x01: Interrupt Uplink Packet.
--
--
--=== 2.3.6 LiDAR temp ===
--
--
--Characterize the internal temperature value of the sensor.
--
--**Example: **
--If payload is: 1C(H) <<24>>24=28(D),LiDAR temp=28℃.
--If payload is: F2(H) <<24>>24=-14(D),LiDAR temp=-14℃.
--
--
--=== 2.3.7 Message Type ===
--
--
  (((
--For a normal uplink payload, the message type is always 0x01.
++0x01: Detect Ultrasonic Sensor
  )))
  (((
--Valid Message Type:
++0x00: No Ultrasonic Sensor
  )))
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:499px" %)
--|=(% style="width: 161px;background-color:#4F81BD;color:white" %)**Message Type Code**|=(% style="width: 164px;background-color:#4F81BD;color:white" %)**Description**|=(% style="width: 174px;background-color:#4F81BD;color:white" %)**Payload**
--|(% style="width:160px" %)0x01|(% style="width:163px" %)Normal Uplink|(% style="width:173px" %)[[Normal Uplink Payload>>||anchor="H2.3A0200BUplinkPayload"]]
--|(% style="width:160px" %)0x02|(% style="width:163px" %)Reply configures info|(% style="width:173px" %)[[Configure Info Payload>>||anchor="H4.3A0GetFirmwareVersionInfo"]]
++=== 2.3.6  Decode payload in The Things Network ===
--
--=== 2.3.8 Decode payload in The Things Network ===
--
--
  While using TTN network, you can add the payload format to decode the payload.
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850829385-439.png?rev=1.1||alt="1654850829385-439.png"]]
--[[image:1654592762713-715.png]]
++The payload decoder function for TTN V3 is here:
--
  (((
--The payload decoder function for TTN is here:
++DDS75-LB TTN V3 Payload Decoder:  [[ttps:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
  )))
--(((
--LDS12-LB TTN Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
--)))
++== 2.4  Uplink Interval ==
--== 2.4 Uplink Interval ==
++The DDS75-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
--The LDS12-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>||anchor="H3.3.1SetTransmitIntervalTime"]]
++== 2.5  Show Data in DataCake IoT Server ==
--== 2.5 Show Data in DataCake IoT Server ==
--
  (((
  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
  )))
++(((
++
++)))
  (((
  (% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
@@ -406,7 +406,7 @@
  (% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
--(% style="color:blue" %)**Step 4**(%%)**: Search the LDS12-LB and add DevEUI.**
++(% style="color:blue" %)**Step 4**(%%)**: Search the DDS75-LB and add DevEUI.**
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
@@ -416,22 +416,23 @@
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
++
  == 2.6 Datalog Feature ==
--Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, LDS12-LB will store the reading for future retrieving purposes.
++Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, SW3L-LB will store the reading for future retrieving purposes.
  === 2.6.1 Ways to get datalog via LoRaWAN ===
--Set PNACKMD=1, LDS12-LB will wait for ACK for every uplink, when there is no LoRaWAN network,LDS12-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
++Set PNACKMD=1, SW3L-LB will wait for ACK for every uplink, when there is no LoRaWAN network,SW3L-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
  * (((
--a) LDS12-LB will do an ACK check for data records sending to make sure every data arrive server.
++a) SW3L-LB will do an ACK check for data records sending to make sure every data arrive server.
  )))
  * (((
--b) LDS12-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but LDS12-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if LDS12-LB gets a ACK, LDS12-LB will consider there is a network connection and resend all NONE-ACK messages.
++b) SW3L-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but SW3L-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if SW3L-LB gets a ACK, SW3L-LB will consider there is a network connection and resend all NONE-ACK messages.
  )))
  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
@@ -442,7 +442,7 @@
  === 2.6.2 Unix TimeStamp ===
--LDS12-LB uses Unix TimeStamp format based on
++SW3L-LB uses Unix TimeStamp format based on
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
@@ -461,7 +461,7 @@
  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
--Once LDS12-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to LDS12-LB. If LDS12-LB fails to get the time from the server, LDS12-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
++Once SW3L-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SW3L-LB. If SW3L-LB fails to get the time from the server, SW3L-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
@@ -489,7 +489,7 @@
  )))
  (((
--Uplink Internal =5s，means LDS12-LB will send one packet every 5s. range 5~~255s.
++Uplink Internal =5s，means SW3L-LB will send one packet every 5s. range 5~~255s.
  )))
@@ -496,293 +496,300 @@
  == 2.7 Frequency Plans ==
--The LDS12-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
++The SW3L-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
--== 2.8 LiDAR ToF Measurement ==
++= 3. Configure SW3L-LB =
--=== 2.8.1 Principle of Distance Measurement ===
++== 3.1 Configure Methods ==
--The LiDAR probe is based on TOF, namely, Time of Flight principle. To be specific, the product emits modulation wave of near infrared ray on a periodic basis, which will be reflected after contacting object. The product obtains the time of flight by measuring round-trip phase difference and then calculates relative range between the product and the detection object, as shown below.
++SW3L-LB supports below configure method:
++* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
--[[image:1654831757579-263.png]]
++* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
++* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
--=== 2.8.2 Distance Measurement Characteristics ===
++== 3.2 General Commands ==
--With optimization of light path and algorithm, The LiDAR probe has minimized influence from external environment on distance measurement performance. Despite that, the range of distance measurement may still be affected by the environment illumination intensity and the reflectivity of detection object. As shown in below:
++These commands are to configure:
--[[image:1654831774373-275.png]]
++* General system settings like: uplink interval.
++* LoRaWAN protocol & radio related command.
--(((
--(% style="color:blue" %)**① **(%%)Represents the detection blind zone of The LiDAR probe, 0-10cm, within which the output data is unreliable.
--)))
++They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
--(((
--(% style="color:blue" %)**② **(%%)Represents the operating range of The LiDAR probe detecting black target with 10% reflectivity, 0.1-5m.
--)))
++[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--(((
--(% style="color:blue" %)**③ **(%%)Represents the operating range of The LiDAR probe detecting white target with 90% reflectivity, 0.1-12m.
--)))
++== 3.3 Commands special design for SW3L-LB ==
--(((
--Vertical Coordinates: Represents the radius of light spot for The LiDAR probe at different distances. The diameter of light spot depends on the FOV of The LiDAR probe (the term of FOV generally refers to the smaller value between the receiving angle and the transmitting angle), which is calculated as follows:
--)))
++These commands only valid for SW3L-LB, as below:
--[[image:1654831797521-720.png]]
++=== 3.3.1 Set Transmit Interval Time ===
++
  (((
--In the formula above, d is the diameter of light spot; D is detecting range; β is the value of the receiving angle of The LiDAR probe, 3.6°. Correspondence between the diameter of light spot and detecting range is given in Table below.
++Feature: Change LoRaWAN End Node Transmit Interval.
  )))
--[[image:1654831810009-716.png]]
++(((
++(% style="color:blue" %)**AT Command: AT+TDC**
++)))
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
++|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
++30000
++OK
++the interval is 30000ms = 30s
++)))
++|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
++OK
++Set transmit interval to 60000ms = 60 seconds
++)))
  (((
--If the light spot reaches two objects with different distances, as shown in Figure 3, the output distance value will be a value between the actual distance values of the two objects. For a high accuracy requirement in practice, the above situation should be noticed to avoid the measurement error.
++(% style="color:blue" %)**Downlink Command: 0x01**
  )))
++(((
++Format: Command Code (0x01) followed by 3 bytes time value.
++)))
--=== 2.8.3  Notice of usage: ===
++(((
++If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
++)))
++* (((
++Example 1: Downlink Payload: 0100001E       ~/~/ Set Transmit Interval (TDC) = 30 seconds
++)))
++* (((
++Example 2: Downlink Payload: 0100003C      ~/~/ Set Transmit Interval (TDC) = 60 seconds
++)))
--Possible invalid /wrong reading for LiDAR ToF tech:
++=== 3.3.2 Quit AT Command ===
--* Measure high reflectivity object such as: Mirror, Smooth ceramic tile, static milk surface, will have possible wrong readings.
--* While there is transparent object such as glass, water drop between the measured object and the LiDAR sensor, the reading might be wrong.
--* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
--* The sensor window is made by Acrylic. Don't touch it with alcohol material. This will destroy the sensor window.
--=== 2.8.4  Reflectivity of different objects ===
++Feature: Quit AT Command mode, so user needs to input the password again before using AT Commands.
++(% style="color:blue" %)**AT Command: AT+DISAT**
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:379px" %)
--|=(% style="width: 54px;background-color:#D9E2F3;color:#0070C0" %)Item|=(% style="width: 231px;background-color:#D9E2F3;color:#0070C0" %)Material|=(% style="width: 94px;background-color:#D9E2F3;color:#0070C0" %)Relectivity
--|(% style="width:53px" %)1|(% style="width:229px" %)Black foam rubber|(% style="width:93px" %)2.4%
--|(% style="width:53px" %)2|(% style="width:229px" %)Black fabric|(% style="width:93px" %)3%
--|(% style="width:53px" %)3|(% style="width:229px" %)Black rubber|(% style="width:93px" %)4%
--|(% style="width:53px" %)4|(% style="width:229px" %)Coal (different types of coal)|(% style="width:93px" %)4~~8%
--|(% style="width:53px" %)5|(% style="width:229px" %)Black car paint|(% style="width:93px" %)5%
--|(% style="width:53px" %)6|(% style="width:229px" %)Black Jam|(% style="width:93px" %)10%
--|(% style="width:53px" %)7|(% style="width:229px" %)Opaque black plastic|(% style="width:93px" %)14%
--|(% style="width:53px" %)8|(% style="width:229px" %)Clean rough board|(% style="width:93px" %)20%
--|(% style="width:53px" %)9|(% style="width:229px" %)Translucent plastic bottle|(% style="width:93px" %)62%
--|(% style="width:53px" %)10|(% style="width:229px" %)Carton cardboard|(% style="width:93px" %)68%
--|(% style="width:53px" %)11|(% style="width:229px" %)Clean pine|(% style="width:93px" %)70%
--|(% style="width:53px" %)12|(% style="width:229px" %)Opaque white plastic|(% style="width:93px" %)87%
--|(% style="width:53px" %)13|(% style="width:229px" %)White Jam|(% style="width:93px" %)90%
--|(% style="width:53px" %)14|(% style="width:229px" %)Kodak Standard Whiteboard|(% style="width:93px" %)100%
--|(% style="width:53px" %)15|(% style="width:229px" %)(((
--Unpolished white metal surface
--)))|(% style="width:93px" %)130%
--|(% style="width:53px" %)16|(% style="width:229px" %)Glossy light metal surface|(% style="width:93px" %)150%
--|(% style="width:53px" %)17|(% style="width:229px" %)stainless steel|(% style="width:93px" %)200%
--|(% style="width:53px" %)18|(% style="width:229px" %)Reflector plate, reflective tape|(% style="width:93px" %)>300%
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:452px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 198px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 99px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:155px" %)AT+DISAT|(% style="width:198px" %)Quit AT Commands mode|(% style="width:96px" %)OK
--= 3. Configure LDS12-LB =
++(% style="color:blue" %)**Downlink Command:**
--== 3.1 Configure Methods ==
++No downlink command for this feature.
--LDS12-LB supports below configure method:
++=== 3.3.3 Get Device Status ===
--* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
--* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
++Send a LoRaWAN downlink to ask device send Alarm settings.
--* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
++(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
--== 3.2 General Commands ==
++Sensor will upload Device Status via FPORT=5. See payload section for detail.
--These commands are to configure:
++=== 3.3.4 Alarm for continuously water flow ===
--* General system settings like: uplink interval.
--* LoRaWAN protocol & radio related command.
++(((
++This feature is to monitor and send Alarm for continuously water flow.
++)))
--They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
++(((
++Example case is for Toilet water monitoring, if some one push toilet button, the toilet will have water flow. If the toilet button has broken and can't returned to original state, the water flow will keep for hours or days which cause huge waste for water.
++)))
--[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
++(((
++To monitor this faulty and send alarm, there are two settings:
++)))
++* (((
++(% style="color:#4f81bd" %)**Stop Duration: Unit: Second**
++)))
--== 3.3 Commands special design for LDS12-LB ==
++(((
++Default: 15s, If SW3L-LB didn't see any water flow in 15s, SW3L-LB will consider stop of water flow event.
++)))
++* (((
++(% style="color:#4f81bd" %)**Alarm Timer: Units: Minute; Default 0 minutes (means Alarm disable)**
++)))
--These commands only valid for LDS12-LB, as below:
++(((
++**Example:** 3 minutes, if SW3L-LB detect a start of water flow event and didn't detect a stop event within Alarm timer, SW3L-LB will send an Alarm to indicate a water flow abnormal alarm.
++)))
++(((
++So for example, If we set stop duration=15s and Alarm Timer=3minutes. If the toilet water flow continuously for more than 3 minutes, Sensor will send an alarm (in Confirmed MODE) to platform.
++)))
--=== 3.3.1 Set Transmit Interval Time ===
--
--
  (((
--Feature: Change LoRaWAN End Node Transmit Interval.
++(% style="color:red" %)**Note:** **After this alarm is send, sensor will consider a stop of water flow and count for another new event. So if water flow waste last for 1 hour, Sensor will keep sending alarm every 3 minutes.**
  )))
  (((
--(% style="color:blue" %)**AT Command: AT+TDC**
++(% style="color:#4f81bd" %)**AT Command**(%%) to configure:
  )))
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
--|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
--30000
--OK
--the interval is 30000ms = 30s
++* (((
++AT+PTRIG=15,3   ~-~-> Set Stop duration: 15s, Alarm Timer: 3 minutes.
  )))
--|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
--OK
--Set transmit interval to 60000ms = 60 seconds
++
++* (((
++AT+ PTRIG=15,0  ~-~-> Default Value, disable water waste Alarm.
  )))
  (((
--(% style="color:blue" %)**Downlink Command: 0x01**
++(% style="color:#4f81bd" %)**Downlink Command**(%%) to configure:
  )))
  (((
--Format: Command Code (0x01) followed by 3 bytes time value.
++Command: **0xAA aa bb cc**
  )))
  (((
--If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
++AA: Command Type Code
  )))
--* (((
--Example 1: Downlink Payload: 0100001E       ~/~/ Set Transmit Interval (TDC) = 30 seconds
++(((
++aa: Stop duration
  )))
--* (((
--Example 2: Downlink Payload: 0100003C      ~/~/ Set Transmit Interval (TDC) = 60 seconds
++
++(((
++bb cc: Alarm Timer
  )))
--=== 3.3.2 Set Interrupt Mode ===
++(((
++If user send 0xAA 0F 00 03: equal to AT+PTRIG=15,3
++)))
--Feature, Set Interrupt mode for PA8 of pin.
++=== 3.3.5 Clear Flash Record ===
--When AT+INTMOD=0 is set, PA8 is used as a digital input port.
--(% style="color:blue" %)**AT Command: AT+INTMOD**
++Feature: Clear flash storage for data log feature.
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
--|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
--0
--OK
--the mode is 0 =Disable Interrupt
--)))
--|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
--Set Transmit Interval
--0. (Disable Interrupt),
--~1. (Trigger by rising and falling edge)
--2. (Trigger by falling edge)
--3. (Trigger by rising edge)
--)))|(% style="width:157px" %)OK
++(% style="color:blue" %)**AT Command: AT+CLRDTA**
--(% style="color:blue" %)**Downlink Command: 0x06**
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
++|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 169px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 174px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:157px" %)AT+CLRDTA|(% style="width:169px" %)Clear flash storage for data log feature.|Clear all stored sensor data… OK
--Format: Command Code (0x06) followed by 3 bytes.
++(((
++(% style="color:blue" %)**Downlink Command:**
++)))
--This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
++(((
++* **Example**: 0xA301     ~/~/  Same as AT+CLRDTA
++)))
--* Example 1: Downlink Payload: 06000000       ~/~/  Turn off interrupt mode
--* Example 2: Downlink Payload: 06000003      ~/~/   Set the interrupt mode to rising edge trigger
++=== 3.3.6 Set the calculate flag ===
--=== 3.3.3 Get Firmware Version Info ===
++Feature: Set the calculate flag
++(% style="color:blue" %)**AT Command: AT+CALCFLAG**
--Feature: use downlink to get firmware version.
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:461px" %)
++|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:158px" %)AT+CALCFLAG =1|(% style="width:192px" %)Set the calculate flag to 1.|(% style="width:109px" %)OK
++|(% style="width:158px" %)AT+CALCFLAG =2|(% style="width:192px" %)Set the calculate flag to 2.|(% style="width:109px" %)OK
--(% style="color:#037691" %)**Downlink Command: 0x26**
++(% style="color:blue" %)**Downlink Command:**
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:492px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:191px" %)**Downlink Control Type**|(% style="background-color:#d9e2f3; color:#0070c0; width:57px" %)**FPort**|(% style="background-color:#d9e2f3; color:#0070c0; width:91px" %)**Type Code**|(% style="background-color:#d9e2f3; color:#0070c0; width:153px" %)**Downlink payload size(bytes)**
--|(% style="width:191px" %)Get Firmware Version Info|(% style="width:57px" %)Any|(% style="width:91px" %)26|(% style="width:151px" %)2
++* **Example**: 0XA501         ~/~/  Same as AT+CALCFLAG =1
--* Reply to the confirmation package: 26 01
--* Reply to non-confirmed packet: 26 00
++=== 3.3.7 Set count number ===
--Device will send an uplink after got this downlink command. With below payload:
--Configures info payload:
++Feature: Manually set the count number
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="background-color:#D9E2F3;color:#0070C0" %)(((
--**Size(bytes)**
--)))|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**5**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
--|**Value**|Software Type|(((
--Frequency
--Band
--)))|Sub-band|(((
--Firmware
--Version
--)))|Sensor Type|Reserve|(((
--[[Message Type>>||anchor="H2.3.7A0MessageType"]]
--Always 0x02
--)))
++(% style="color:blue" %)**AT Command: AT+SETCNT**
--(% style="color:#037691" %)**Software Type**(%%): Always 0x03 for LLDS12
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:479px" %)
++|=(% style="width: 160px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 223px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 96px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:160px" %)AT+ SETCNT =0|(% style="width:221px" %)Set the count number to 0.|(% style="width:95px" %)OK
++|(% style="width:160px" %)AT+ SETCNT =100|(% style="width:221px" %)Set the count number to 100.|(% style="width:95px" %)OK
--(% style="color:#037691" %)**Frequency Band**:
++(% style="color:blue" %)**Downlink Command:**
--*0x01: EU868
++* **Example**: 0xA6000001      ~/~/  Same as AT+ SETCNT =1
--*0x02: US915
++* **Example**: 0xA6000064      ~/~/  Same as AT+ SETCNT =100
--*0x03: IN865
++=== 3.3.8 Set Interrupt Mode ===
--*0x04: AU915
--*0x05: KZ865
++Feature, Set Interrupt mode for PA8 of pin.
--*0x06: RU864
++When AT+INTMOD=0 is set, PA8 is used as a digital input port.
--*0x07: AS923
++(% style="color:blue" %)**AT Command: AT+INTMOD**
--*0x08: AS923-1
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
++0
++OK
++the mode is 0 =Disable Interrupt
++)))
++|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
++Set Transmit Interval
++0. (Disable Interrupt),
++~1. (Trigger by rising and falling edge)
++2. (Trigger by falling edge)
++3. (Trigger by rising edge)
++)))|(% style="width:157px" %)OK
--*0x09: AS923-2
++(% style="color:blue" %)**Downlink Command: 0x06**
--*0xa0: AS923-3
++Format: Command Code (0x06) followed by 3 bytes.
++This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
--(% style="color:#037691" %)**Sub-Band**(%%): value 0x00 ~~ 0x08
++* Example 1: Downlink Payload: 06000000       ~/~/  Turn off interrupt mode
--(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
++* Example 2: Downlink Payload: 06000003      ~/~/   Set the interrupt mode to rising edge trigger
--(% style="color:#037691" %)**Sensor Type**:
++=== 3.3.9 Set work mode ===
--0x01: LSE01
--0x02: LDDS75
++Feature: Manually set the work mode
--0x03: LDDS20
--0x04: LLMS01
++(% style="color:blue" %)**AT Command: AT+MOD**
--0x05: LSPH01
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:463px" %)
++|=(% style="width: 162px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 108px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:162px" %)AT+MOD=0|(% style="width:191px" %)Set the work mode to 0.|(% style="width:106px" %)OK
++|(% style="width:162px" %)AT+MOD=1|(% style="width:191px" %)Set the work mode to 1|(% style="width:106px" %)OK
--0x06: LSNPK01
++(% style="color:blue" %)**Downlink Command:**
--0x07: LLDS12
++* **Example: **0x0A00       ~/~/  Same as AT+MOD=0
++* **Example:** 0x0A01       ~/~/  Same as AT+MOD=1
  = 4. Battery & Power Consumption =
--LDS12-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++SW3L-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
@@ -791,7 +791,7 @@
  (% class="wikigeneratedid" %)
--User can change firmware LDS12-LB to:
++User can change firmware SW3L-LB to:
  * Change Frequency band/ region.
@@ -799,80 +799,82 @@
  * Fix bugs.
--Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/ph4uyz0rchflrnw/AADr1f_5Sg30804NItpfOQbla?dl=0]]**
++Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
  Methods to Update Firmware:
--* (Recommanded way) OTA firmware update via wireless:  **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
++* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
--* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
++* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
  = 6. FAQ =
--== 6.1 What is the frequency plan for LDS12-LB? ==
++== 6.1  AT Commands input doesn't work ==
--LDS12-LB use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
++In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
--= 7. Trouble Shooting =
++= 7. Order Info =
--== 7.1 AT Command input doesn't work ==
++Part Number: (% style="color:blue" %)**SW3L-LB-XXX-YYY**
--In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:blue" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:blue" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
++(% style="color:red" %)**XXX**(%%): The default frequency band
++* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
--== 7.2 Significant error between the output distant value of LiDAR and actual distance ==
++* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
++* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
++* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
++
++* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
++
++* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
++
++* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
++
++* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
++
  (((
--(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
++(% style="color:blue" %)**YYY**(%%): Flow Sensor Model:
  )))
  (((
--Troubleshooting: Please avoid use of this product under such circumstance in practice.
++  **004:** DW-004 Flow Sensor: diameter: G1/2” / DN15.  450 pulse = 1 L
  )))
--
  (((
--(% style="color:blue" %)**Cause ②**(%%)**: **The IR-pass filters are blocked.
++  **006:** DW-006 Flow Sensor: diameter: G3/4” / DN20.  390 pulse = 1 L
  )))
  (((
--Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter.
++  **010:** DW-010 Flow Sensor: diameter: G 1” / DN25.   64 pulse = 1 L
  )))
++* (((
++calculate flag=0: for SW3L-004 Flow Sensor: 450 pulse = 1 L
++)))
--= 8. Order Info =
++* (((
++calculate flag=1: for SW3L-006 Flow Sensor: 390 pulse = 1 L
++)))
++* (((
++calculate flag=2: for SW3L-010 Flow Sensor: 64   pulse = 1 L
--Part Number: (% style="color:blue" %)**LDS12-LB-XXX**
--(% style="color:red" %)**XXX**(%%): **The default frequency band**
++
++)))
--* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
++= 8. Packing Info =
--* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
--* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
--
--* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
--
--* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
--
--* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
--
--* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
--
--* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--
--= 9. Packing Info =
--
--
  (% style="color:#037691" %)**Package Includes**:
--* LDS12-LB LoRaWAN LiDAR ToF Distance Sensor x 1
++* SW3L-LB LoRaWAN Flow Sensor
  (% style="color:#037691" %)**Dimension and weight**:
@@ -884,7 +884,7 @@
  * Weight / pcs : g
--= 10. Support =
++= 9. Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

image-20230613100900-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-184.0 KB

Content

image-20230613102426-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-89.3 KB

Content

image-20230613102459-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-89.3 KB

Content

image-20230613133647-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-213.6 KB

Content

image-20230613133716-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-165.8 KB

Content

image-20230613140115-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-92.1 KB

Content

image-20230613140140-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-92.1 KB

Content

image-20230613143052-5.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-21.8 KB

Content

image-20230613143125-6.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-24.7 KB

Content

image-20230614153353-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-112.1 KB

Content

image-20230614162334-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-88.3 KB

Content

image-20230614162359-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-88.3 KB

Content