Skip to Content
Last modified by Mengting Qiu on 2023/12/14 11:15
From version 73.6
edited by Xiaoling
on 2023/06/13 10:40
Change comment: There is no comment for this version
To version 62.3
edited by Xiaoling
on 2023/05/30 09:08
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -DDS45-LB -- LoRaWAN Distance Detection Sensor User Manual
1 +CPL03-LB -- LoRaWAN Pulse/Contact Sensor User Manual
Content
... ... @@ -1,8 +1,7 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20230613100900-1.png||height="683" width="683"]]
2 +[[image:image-20230530084608-2.jpeg||height="707" width="707"]]
3 3  
4 4  
5 -
6 6  **Table of Contents：**
7 7  
8 8  {{toc/}}
... ... @@ -14,42 +14,42 @@
14 14  
15 15  = 1. Introduction =
16 16  
17 -== 1.1 What is LoRaWAN Distance Detection Sensor ==
16 +== 1.1 What is CPL03-LB LoRaWAN Pulse/Contact Sensor ==
18 18  
19 19  
20 -The Dragino DDS45-LB is a (% style="color:blue" %)** LoRaWAN Distance Detection Sensor**(%%) for Internet of Things solution. It is used to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses (% style="color:blue" %)** ultrasonic sensing technology**(%%) for (% style="color:blue" %)**distance measurement**(%%), and (% style="color:blue" %)** temperature compensation**(%%) is performed internally to improve the reliability of data. The DDS45-LB can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc.
19 +The Dragino CPL03-LB is a (% style="color:blue" %)**LoRaWAN Contact Sensor**(%%) for Internet of Things solution. It detects dry contact status, open time, open counts, and then upload to IoT server via LoRaWAN wireless protocol.
21 21  
22 -It detects the distance(% style="color:blue" %)**  between the measured object and the sensor**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
21 +The CPL03-LB will send periodically data every day as well as for each dry contact action. It also counts the contact open times and calculate last open duration. User can also disable the uplink for each open/close event, instead, device can count each open event and uplink periodically.
23 23  
24 -The LoRa wireless technology used in DDS45-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
23 +The temperature & humidity sensor used in CPL03-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
25 25  
26 -DDS45-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
25 +The LoRa wireless technology used in CPL03-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
27 27  
28 -DDS45-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
27 +CPL03-LB (% style="color:blue" %)**supports open alarm feature**(%%), user can set open alarm for instant notice. CPL03-LB (% style="color:blue" %)**supports Datalog feature**, it can save the data when there is no LoRaWAN network and uplink when network recover.
29 29  
30 -Each DDS45-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
29 +CPL03-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
31 31  
32 -[[image:image-20230613102459-3.png||height="476" width="855"]]
31 +CPL03-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
33 33  
33 +Each CPL03-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
34 34  
35 +
35 35  == 1.2 ​Features ==
36 36  
37 37  
38 38  * LoRaWAN 1.0.3 Class A
39 -* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
40 40  * Ultra-low power consumption
41 -* Distance Detection by Ultrasonic technology
42 -* Flat object range 30mm - 4500mm
43 -* Accuracy: ±(1cm+S*0.3%) (S: Distance)
44 -* Measure Angle: 60°
45 -* Cable Length : 25cm
41 +* External 3 meters SHT31 probe (For S31-LB)
42 +* Measure range -55°C ~~ 125°C
43 +* Temperature & Humidity alarm
44 +* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
46 46  * Support Bluetooth v5.1 and LoRaWAN remote configure
47 47  * Support wireless OTA update firmware
48 -* AT Commands to change parameters
47 +* Uplink on periodically
49 49  * Downlink to change configure
50 -* IP66 Waterproof Enclosure
51 51  * 8500mAh Battery for long term use
52 52  
51 +
53 53  == 1.3 Specification ==
54 54  
55 55  
... ... @@ -58,6 +58,20 @@
58 58  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
59 59  * Operating Temperature: -40 ~~ 85°C
60 60  
60 +(% style="color:#037691" %)**Temperature Sensor:**
61 +
62 +* Range: -40 to + 80°C
63 +* Accuracy: ±0.2 @ 0-90 °C
64 +* Resolution: 0.1°C
65 +* Long Term Shift: <0.03 °C/yr
66 +
67 +(% style="color:#037691" %)**Humidity Sensor: **
68 +
69 +* Range: 0 ~~ 99.9% RH
70 +* Accuracy: ± 2%RH ( 0 ~~ 100%RH)
71 +* Resolution: 0.01% RH
72 +* Long Term Shift: <0.25 %RH/yr
73 +
61 61  (% style="color:#037691" %)**LoRa Spec:**
62 62  
63 63  * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
... ... @@ -78,69 +78,16 @@
78 78  * Sleep Mode: 5uA @ 3.3v
79 79  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
80 80  
81 -== 1.4 Rated environmental conditions ==
82 82  
95 +== 1.4 Sleep mode and working mode ==
83 83  
84 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
85 -|(% style="background-color:#d9e2f3; color:#0070c0; width:163px" %)**Item**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)(((
86 -**Minimum value**
87 -)))|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)(((
88 -**Typical value**
89 -)))|(% style="background-color:#d9e2f3; color:#0070c0; width:87px" %)(((
90 -**Maximum value**
91 -)))|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**Unit**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Remarks**
92 -|(% style="width:174px" %)Storage temperature|(% style="width:86px" %)-25|(% style="width:66px" %)25|(% style="width:90px" %)80|(% style="width:48px" %)℃|(% style="width:203px" %)
93 -|(% style="width:174px" %)Storage humidity|(% style="width:86px" %) |(% style="width:66px" %)65%|(% style="width:90px" %)90%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
94 -|(% style="width:174px" %)Operating temperature|(% style="width:86px" %)-15|(% style="width:66px" %)25|(% style="width:90px" %)60|(% style="width:48px" %)℃|(% style="width:203px" %)
95 -|(% style="width:174px" %)Working humidity|(% style="width:86px" %)(((
96 -
97 97  
98 -
99 -)))|(% style="width:66px" %)65%|(% style="width:90px" %)80%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
100 -
101 -(((
102 -(% style="color:red" %)**Remarks: (1) a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);       **
103 -
104 -(% style="color:red" %)** b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
105 -
106 -
107 -)))
108 -
109 -== 1.5 Effective measurement range Reference beam pattern ==
110 -
111 -
112 -(% style="color:blue" %)**1. The tested object is a white cylindrical tube made of PVC, with a height of 100cm and a diameter of 7.5cm.**
113 -
114 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852253176-749.png?rev=1.1||alt="1654852253176-749.png"]]
115 -
116 -
117 -(% style="color:blue" %)**2. The object to be tested is a "corrugated cardboard box" perpendicular to the central axis of 0 °, and the length * width is 60cm * 50cm.**
118 -
119 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852175653-550.png?rev=1.1||alt="1654852175653-550.png"]]
120 -
121 -
122 -== 1.6 Applications ==
123 -
124 -
125 -* Horizontal distance measurement
126 -* Liquid level measurement
127 -* Parking management system
128 -* Object proximity and presence detection
129 -* Intelligent trash can management system
130 -* Robot obstacle avoidance
131 -* Automatic control
132 -* Sewer
133 -* Bottom water level monitoring
134 -
135 -== 1.7 Sleep mode and working mode ==
136 -
137 -
138 138  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
139 139  
140 140  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
141 141  
142 142  
143 -== 1.8 Button & LEDs ==
103 +== 1.5 Button & LEDs ==
144 144  
145 145  
146 146  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
... ... @@ -159,12 +159,13 @@
159 159  )))
160 160  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
161 161  
162 -== 1.9 BLE connection ==
163 163  
123 +== 1.6 BLE connection ==
164 164  
165 -DDS45-LB support BLE remote configure.
166 166  
126 +S31x-LB support BLE remote configure.
167 167  
128 +
168 168  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
169 169  
170 170  * Press button to send an uplink
... ... @@ -174,38 +174,56 @@
174 174  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
175 175  
176 176  
177 -== 1.10 Pin Definitions ==
138 +== 1.7 Pin Definitions ==
178 178  
179 179  [[image:image-20230523174230-1.png]]
180 180  
181 181  
182 -== 1.11 Mechanical ==
143 +== 1.8 Hardware Variant ==
183 183  
184 184  
185 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
146 +(% border="1" cellspacing="5" style="width:472px" %)
147 +|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 187px; background-color:#D9E2F3;color:#0070C0" %)Probe Info
148 +|(% style="width:102px" %)(((
149 +S31-LB
150 +)))|(% style="width:190px" %)[[image:image-20230527093214-2.jpeg]]|(% style="width:187px" %)(((
151 +1 x SHT31 Probe
186 186  
153 +Cable Length : 2 meters
187 187  
188 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
155 +
156 +)))
157 +|(% style="width:102px" %)(((
158 +S31B-LB
159 +)))|(% style="width:190px" %)[[image:image-20230527093155-1.jpeg]]|(% style="width:187px" %)(((
160 +1 x SHT31 Probe
189 189  
162 +Installed in device.
163 +)))
190 190  
191 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
165 +(% style="display:none" %)
192 192  
193 193  
194 -(% style="color:blue" %)**Probe Mechanical:**
195 195  
196 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS45%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654915562090-396.png?rev=1.1||alt="1654915562090-396.png"]]
169 +== 1.9 Mechanical ==
197 197  
198 198  
172 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
199 199  
200 200  
201 -= 2. Configure DDS45-LB to connect to LoRaWAN network =
175 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
202 202  
177 +
178 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
179 +
180 +
181 += 2. Configure S31x-LB to connect to LoRaWAN network =
182 +
203 203  == 2.1 How it works ==
204 204  
205 205  
206 -The DDS45-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DDS45-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
186 +The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
207 207  
208 -(% style="display:none" %) (%%)
209 209  
210 210  == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
211 211  
... ... @@ -212,15 +212,13 @@
212 212  
213 213  Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
214 214  
215 -The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
194 +The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
216 216  
217 -[[image:image-20230613102426-2.png||height="476" width="855"]](% style="display:none" %)
218 218  
197 +(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.
219 219  
220 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DDS45-LB.
199 +Each S31x-LB is shipped with a sticker with the default device EUI as below:
221 221  
222 -Each DDS45-LB is shipped with a sticker with the default device EUI as below:
223 -
224 224  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
225 225  
226 226  
... ... @@ -248,10 +248,10 @@
248 248  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
249 249  
250 250  
251 -(% style="color:blue" %)**Step 2:**(%%) Activate on DDS45-LB
228 +(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
252 252  
253 253  
254 -Press the button for 5 seconds to activate the DDS45-LB.
231 +Press the button for 5 seconds to activate the S31x-LB.
255 255  
256 256  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
257 257  
... ... @@ -258,169 +258,174 @@
258 258  After join success, it will start to upload messages to TTN and you can see the messages in the panel.
259 259  
260 260  
261 -== 2.3  ​Uplink Payload ==
238 +== 2.3 ​Uplink Payload ==
262 262  
240 +=== 2.3.1 Device Status, FPORT~=5 ===
263 263  
264 -(((
265 -DDS45-LB will uplink payload via LoRaWAN with below payload format: 
266 -)))
267 267  
268 -(((
269 -Uplink payload includes in total 8 bytes.
270 -)))
243 +Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
271 271  
272 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
273 -|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
274 -**Size(bytes)**
275 -)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)1|=(% style="background-color:#D9E2F3;color:#0070C0" %)2|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
276 -|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((
277 -[[Distance>>||anchor="H2.3.2A0Distance"]]
278 -(unit: mm)
279 -)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((
280 -[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]
281 -)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]
245 +The Payload format is as below.
282 282  
283 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850511545-399.png?rev=1.1||alt="1654850511545-399.png"]]
284 284  
248 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
249 +|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
250 +|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
251 +|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
285 285  
286 -=== 2.3.1  Battery Info ===
253 +Example parse in TTNv3
287 287  
255 +[[image:image-20230524144422-1.png||height="174" width="1080"]]
288 288  
289 -Check the battery voltage for DDS45-LB.
290 290  
291 -Ex1: 0x0B45 = 2885mV
258 +(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
292 292  
293 -Ex2: 0x0B49 = 2889mV
260 +(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
294 294  
262 +(% style="color:#037691" %)**Frequency Band**:
295 295  
296 -=== 2.3.2  Distance ===
264 +*0x01: EU868
297 297  
266 +*0x02: US915
298 298  
299 -(((
300 -Get the distance. Flat object range 30mm - 4500mm.
301 -)))
268 +*0x03: IN865
302 302  
303 -(((
304 -For example, if the data you get from the register is **0x0B 0x05**, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
270 +*0x04: AU915
305 305  
306 -(% style="color:blue" %)**0B05(H) = 2821 (D) = 2821 mm.**
307 -)))
272 +*0x05: KZ865
308 308  
274 +*0x06: RU864
309 309  
310 -* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
311 -* If the sensor value lower than 0x001E (30mm), the sensor value will be 0x00.
276 +*0x07: AS923
312 312  
278 +*0x08: AS923-1
313 313  
280 +*0x09: AS923-2
314 314  
282 +*0x0a: AS923-3
315 315  
316 -=== 2.3.3  Interrupt Pin ===
284 +*0x0b: CN470
317 317  
286 +*0x0c: EU433
318 318  
319 -This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
288 +*0x0d: KR920
320 320  
321 -**Example:**
290 +*0x0e: MA869
322 322  
323 -0x00: Normal uplink packet.
324 324  
325 -0x01: Interrupt Uplink Packet.
293 +(% style="color:#037691" %)**Sub-Band**:
326 326  
295 +AU915 and US915:value 0x00 ~~ 0x08
327 327  
328 -=== 2.3.4  DS18B20 Temperature sensor ===
297 +CN470: value 0x0B ~~ 0x0C
329 329  
299 +Other Bands: Always 0x00
330 330  
331 -This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
332 332  
333 -**Example**:
302 +(% style="color:#037691" %)**Battery Info**:
334 334  
335 -If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
304 +Check the battery voltage.
336 336  
337 -If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
306 +Ex1: 0x0B45 = 2885mV
338 338  
308 +Ex2: 0x0B49 = 2889mV
339 339  
340 -=== 2.3.5  Sensor Flag ===
341 341  
311 +=== 2.3.2  Sensor Data. FPORT~=2 ===
342 342  
343 -(((
344 -0x01: Detect Ultrasonic Sensor
345 -)))
346 346  
347 -(((
348 -0x00: No Ultrasonic Sensor
314 +Sensor Data is uplink via FPORT=2
315 +
316 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
317 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
318 +**Size(bytes)**
319 +)))|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)**2**|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
320 +|(% style="width:99px" %)Value|(% style="width:69px" %)(((
321 +Battery
322 +)))|(% style="width:130px" %)(((
323 +Unix TimeStamp
324 +)))|(% style="width:194px" %)(((
325 +Alarm Flag & MOD& Level of PA8
326 +)))|(% style="width:106px" %)(((
327 +Temperature
328 +)))|(% style="width:97px" %)(((
329 +Humidity
349 349  )))
350 350  
332 +[[image:image-20230524144456-2.png||height="180" width="1142"]]
351 351  
352 -=== 2.3.6  Decode payload in The Things Network ===
353 353  
335 +==== (% style="color:#4472c4" %)**Battery**(%%) ====
354 354  
355 -While using TTN network, you can add the payload format to decode the payload.
337 +Sensor Battery Level.
356 356  
357 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850829385-439.png?rev=1.1||alt="1654850829385-439.png"]]
339 +Ex1: 0x0B45 = 2885mV
358 358  
359 -The payload decoder function for TTN V3 is here:
341 +Ex2: 0x0B49 = 2889mV
360 360  
361 -(((
362 -DDS45-LB TTN V3 Payload Decoder:  [[ttps:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
363 -)))
364 364  
365 365  
366 -== 2.4  Uplink Interval ==
345 +==== (% style="color:#4472c4" %)**Temperature**(%%) ====
367 367  
347 +**Example**:
368 368  
369 -The DDS45-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>||anchor="H3.3.1SetTransmitIntervalTime"]]
349 +If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
370 370  
351 +If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
371 371  
372 -== 2.5  ​Show Data in DataCake IoT Server ==
353 +（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
373 373  
374 374  
375 -(((
376 -[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
377 -)))
356 +==== (% style="color:#4472c4" %)**Humidity**(%%) ====
378 378  
379 379  
380 -(((
381 -(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
382 -)))
359 +Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
383 383  
384 -(((
385 -(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
386 -)))
387 387  
362 +==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
388 388  
389 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592790040-760.png?rev=1.1||alt="1654592790040-760.png"]]
390 390  
365 +**Example:**
391 391  
392 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592800389-571.png?rev=1.1||alt="1654592800389-571.png"]]
367 +If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
393 393  
369 +If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
394 394  
395 -(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
371 +If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
396 396  
397 -(% style="color:blue" %)**Step 4**(%%)**: Search the DDS45-LB and add DevEUI.**
373 +If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
398 398  
399 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
375 +If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
400 400  
377 +If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
401 401  
402 -After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake.
403 403  
404 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
380 +== 2.4 Payload Decoder file ==
405 405  
406 406  
383 +In TTN, use can add a custom payload so it shows friendly reading
407 407  
408 -== 2.6 Datalog Feature ==
385 +In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
409 409  
387 +[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
410 410  
411 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DDS45-LB will store the reading for future retrieving purposes.
412 412  
390 +== 2.5 Datalog Feature ==
413 413  
414 -=== 2.6.1 Ways to get datalog via LoRaWAN ===
415 415  
393 +Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
416 416  
417 -Set PNACKMD=1, DDS45-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DDS45-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
418 418  
396 +=== 2.5.1 Ways to get datalog via LoRaWAN ===
397 +
398 +
399 +Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
400 +
419 419  * (((
420 -a) DDS45-LB will do an ACK check for data records sending to make sure every data arrive server.
402 +a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
421 421  )))
422 422  * (((
423 -b) DDS45-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but DDS45-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DDS45-LB gets a ACK, DDS45-LB will consider there is a network connection and resend all NONE-ACK messages.
405 +b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
424 424  )))
425 425  
426 426  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
... ... @@ -428,10 +428,10 @@
428 428  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
429 429  
430 430  
431 -=== 2.6.2 Unix TimeStamp ===
413 +=== 2.5.2 Unix TimeStamp ===
432 432  
433 433  
434 -DDS45-LB uses Unix TimeStamp format based on
416 +S31x-LB uses Unix TimeStamp format based on
435 435  
436 436  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
437 437  
... ... @@ -445,64 +445,147 @@
445 445  So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
446 446  
447 447  
448 -=== 2.6.3 Set Device Time ===
430 +=== 2.5.3 Set Device Time ===
449 449  
450 450  
451 451  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
452 452  
453 -Once DDS45-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to DDS45-LB. If DDS45-LB fails to get the time from the server, DDS45-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
435 +Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
454 454  
455 455  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
456 456  
457 457  
458 -=== 2.6.4 Poll sensor value ===
440 +=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
459 459  
460 460  
461 -Users can poll sensor values based on timestamps. Below is the downlink command.
443 +The Datalog uplinks will use below payload format.
462 462  
463 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
464 -|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
465 -|(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
466 -|(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
445 +**Retrieval data payload:**
467 467  
447 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
448 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
449 +**Size(bytes)**
450 +)))|=(% style="width: 40px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 65px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px; background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 100px; background-color:#D9E2F3;color:#0070C0" %)**4**
451 +|(% style="width:103px" %)Value|(% style="width:68px" %)(((
452 +ignore
453 +)))|(% style="width:104px" %)(((
468 468  (((
469 -Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
455 +Humidity
470 470  )))
471 471  
472 472  (((
473 -For example, downlink command [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20220518162852-1.png?rev=1.1||alt="image-20220518162852-1.png"]]
459 +
474 474  )))
461 +)))|(% style="width:87px" %)(((
462 +Temperature
463 +)))|(% style="width:178px" %)(((
464 +Poll message flag & Alarm Flag& Level of PA8
465 +)))|(% style="width:137px" %)Unix Time Stamp
475 475  
467 +**Poll message flag & Alarm Flag & Level of PA8:**
468 +
469 +[[image:image-20230524114302-1.png||height="115" width="736"]]
470 +
471 +
472 +**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
473 +
474 +**Poll Message Flag**: 1: This message is a poll message reply.
475 +
476 +* Poll Message Flag is set to 1.
477 +
478 +* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
479 +
480 +For example, in US915 band, the max payload for different DR is:
481 +
482 +**a) DR0:** max is 11 bytes so one entry of data
483 +
484 +**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
485 +
486 +**c) DR2:** total payload includes 11 entries of data
487 +
488 +**d) DR3: **total payload includes 22 entries of data.
489 +
490 +If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
491 +
492 +**Example:**
493 +
494 +If S31x-LB has below data inside Flash:
495 +
496 +[[image:image-20230524114654-2.png]]
497 +
498 +
499 +If user sends below downlink command: 31646D84E1646D856C05
500 +
501 +Where : Start time: 646D84E1 = time 23/5/24 03:30:41
502 +
503 + Stop time: 646D856C= time 23/5/24 03:33:00
504 +
505 +
506 +**S31x-LB will uplink this payload.**
507 +
508 +[[image:image-20230524114826-3.png||height="448" width="1244"]]
509 +
476 476  (((
477 -Is to check 2021/11/12 12:00:00 to 2021/11/12 15:00:00's data
511 +00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
478 478  )))
479 479  
480 480  (((
481 -Uplink Internal =5s，means DDS45-LB will send one packet every 5s. range 5~~255s.
515 +Where the first 11 bytes is for the first entry:
482 482  )))
483 483  
518 +(((
519 +00 00 02 36 01 10 40 64 6D 84 E1
520 +)))
484 484  
522 +(((
523 +**Hum**=0x0236/10=56.6
524 +)))
525 +
526 +(((
527 +**Temp**=0x0110/10=27.2
528 +)))
529 +
530 +(((
531 +**poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
532 +)))
533 +
534 +(((
535 +**Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
536 +)))
537 +
538 +
539 +(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
540 +
541 +== 2.6 Temperature Alarm Feature ==
542 +
543 +
544 +S31x-LB work flow with Alarm feature.
545 +
546 +
547 +[[image:image-20230524110125-3.png||height="768" width="1115"]]
548 +
549 +
550 +
485 485  == 2.7 Frequency Plans ==
486 486  
487 487  
488 -The DDS45-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
554 +The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
489 489  
490 490  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
491 491  
492 492  
493 -= 3. Configure DDS45-LB =
559 += 3. Configure S31x-LB =
494 494  
495 495  == 3.1 Configure Methods ==
496 496  
497 497  
498 -DDS45-LB supports below configure method:
564 +S31x-LB supports below configure method:
499 499  
500 500  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
501 -
502 502  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
503 -
504 504  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
505 505  
570 +
506 506  == 3.2 General Commands ==
507 507  
508 508  
... ... @@ -509,7 +509,6 @@
509 509  These commands are to configure:
510 510  
511 511  * General system settings like: uplink interval.
512 -
513 513  * LoRaWAN protocol & radio related command.
514 514  
515 515  They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
... ... @@ -517,25 +517,21 @@
517 517  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
518 518  
519 519  
520 -== 3.3 Commands special design for DDS45-LB ==
584 +== 3.3 Commands special design for S31x-LB ==
521 521  
522 522  
523 -These commands only valid for DDS45-LB, as below:
587 +These commands only valid for S31x-LB, as below:
524 524  
525 525  
526 526  === 3.3.1 Set Transmit Interval Time ===
527 527  
528 528  
529 -(((
530 530  Feature: Change LoRaWAN End Node Transmit Interval.
531 -)))
532 532  
533 -(((
534 534  (% style="color:blue" %)**AT Command: AT+TDC**
535 -)))
536 536  
537 537  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
538 -|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
598 +|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**
539 539  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
540 540  30000
541 541  OK
... ... @@ -546,156 +546,201 @@
546 546  Set transmit interval to 60000ms = 60 seconds
547 547  )))
548 548  
549 -(((
550 550  (% style="color:blue" %)**Downlink Command: 0x01**
551 -)))
552 552  
553 -(((
554 554  Format: Command Code (0x01) followed by 3 bytes time value.
555 -)))
556 556  
557 -(((
558 558  If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
559 -)))
560 560  
561 -* (((
562 -Example 1: Downlink Payload: 0100001E  ~/~/ Set Transmit Interval (TDC) = 30 seconds
563 -)))
564 -* (((
565 -Example 2: Downlink Payload: 0100003C  ~/~/ Set Transmit Interval (TDC) = 60 seconds
615 +* Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
616 +* Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
566 566  
567 567  
568 -
569 -)))
619 +=== 3.3.2 Get Device Status ===
570 570  
571 -=== 3.3.2 Set Interrupt Mode ===
572 572  
622 +Send a LoRaWAN downlink to ask device send Alarm settings.
573 573  
574 -Feature, Set Interrupt mode for PA8 of pin.
624 +(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
575 575  
576 -When AT+INTMOD=0 is set, PA8 is used as a digital input port.
626 +Sensor will upload Device Status via FPORT=5. See payload section for detail.
577 577  
578 -(% style="color:blue" %)**AT Command: AT+INTMOD**
579 579  
580 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
581 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
582 -|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
583 -0
584 -OK
585 -the mode is 0 =Disable Interrupt
586 -)))
587 -|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
588 -Set Transmit Interval
589 -0. (Disable Interrupt),
590 -~1. (Trigger by rising and falling edge)
591 -2. (Trigger by falling edge)
592 -3. (Trigger by rising edge)
593 -)))|(% style="width:157px" %)OK
629 +=== 3.3.3 Set Temperature Alarm Threshold ===
594 594  
595 -(% style="color:blue" %)**Downlink Command: 0x06**
596 596  
597 -Format: Command Code (0x06) followed by 3 bytes.
632 +* (% style="color:blue" %)**AT Command:**
598 598  
599 -This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
634 +(% style="color:#037691" %)**AT+SHTEMP=min,max**
600 600  
601 -* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
636 +* When min=0, and max≠0, Alarm higher than max
637 +* When min≠0, and max=0, Alarm lower than min
638 +* When min≠0 and max≠0, Alarm higher than max or lower than min
602 602  
603 -* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
640 +Example:
604 604  
605 -= 4. Battery & Power Consumption =
642 + AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
606 606  
644 +* (% style="color:blue" %)**Downlink Payload:**
607 607  
608 -DDS45-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
646 +(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
609 609  
610 -[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
648 +(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
611 611  
612 612  
613 -= 5. OTA Firmware update =
651 +=== 3.3.4 Set Humidity Alarm Threshold ===
614 614  
615 615  
616 -(% class="wikigeneratedid" %)
617 -User can change firmware DDS45-LB to:
654 +* (% style="color:blue" %)**AT Command:**
618 618  
619 -* Change Frequency band/ region.
656 +(% style="color:#037691" %)**AT+SHHUM=min,max**
620 620  
621 -* Update with new features.
658 +* When min=0, and max≠0, Alarm higher than max
659 +* When min≠0, and max=0, Alarm lower than min
660 +* When min≠0 and max≠0, Alarm higher than max or lower than min
622 622  
623 -* Fix bugs.
662 +Example:
624 624  
625 -Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/7la95mae0fn03xe/AACtzs-32m22TLb75B-iIr-Qa?dl=0]]**
664 + AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
626 626  
627 -Methods to Update Firmware:
666 +* (% style="color:blue" %)**Downlink Payload:**
628 628  
629 -* (Recommanded way) OTA firmware update via wireless:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
668 +(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
630 630  
631 -* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
670 +(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
632 632  
633 -= 6. FAQ =
634 634  
635 -== 6.1  What is the frequency plan for DDS45-LB? ==
673 +=== 3.3.5 Set Alarm Interval ===
636 636  
637 637  
638 -DDS45-LB use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
676 +The shortest time of two Alarm packet. (unit: min)
639 639  
678 +* (% style="color:blue" %)**AT Command:**
640 640  
641 -== 6.2  Can I use DDS45-LB in condensation environment? ==
680 +(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
642 642  
682 +* (% style="color:blue" %)**Downlink Payload:**
643 643  
644 -DDS45-LB is not suitable to be used in condensation environment. Condensation on the DDS45-LB probe will affect the reading and always got 0.
684 +(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
645 645  
646 646  
647 -= 7.  Trouble Shooting =
687 +=== 3.3.6 Get Alarm settings ===
648 648  
649 -== 7.1  Why I can't join TTN V3 in US915 / AU915 bands? ==
650 650  
690 +Send a LoRaWAN downlink to ask device send Alarm settings.
651 651  
652 -It is due to channel mapping. Please see below link:  [[Frequency band>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]]
692 +* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
653 653  
694 +**Example:**
654 654  
655 -== 7.2  AT Command input doesn't work ==
696 +[[image:image-20230524110211-4.png]]
656 656  
698 +**Explain:**
657 657  
658 -In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:blue" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:blue" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
700 +* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
659 659  
660 660  
661 -== 7.3  Why does the sensor reading show 0 or "No sensor" ==
703 +=== 3.3.7 Set Interrupt Mode ===
662 662  
663 663  
664 -~1. The measurement object is very close to the sensor, but in the blind spot of the sensor.
706 +Feature, Set Interrupt mode for PA8 of pin.
665 665  
666 -2. Sensor wiring is disconnected
708 +When AT+INTMOD=0 is set, PA8 is used as a digital input port.
667 667  
668 -3. Not using the correct decoder
710 +(% style="color:blue" %)**AT Command: AT+INTMOD**
669 669  
712 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
713 +|=(% style="width: 155px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3" %)**Response**
714 +|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
715 +0
716 +OK
717 +the mode is 0 =Disable Interrupt
718 +)))
719 +|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
720 +Set Transmit Interval
721 +0. (Disable Interrupt),
722 +~1. (Trigger by rising and falling edge)
723 +2. (Trigger by falling edge)
724 +3. (Trigger by rising edge)
725 +)))|(% style="width:157px" %)OK
670 670  
671 -== 7.4  Abnormal readings The gap between multiple readings is too large or the gap between the readings and the actual value is too large ==
727 +(% style="color:blue" %)**Downlink Command: 0x06**
672 672  
729 +Format: Command Code (0x06) followed by 3 bytes.
673 673  
674 -1) Please check if there is something on the probe affecting its measurement (condensed water, volatile oil, etc.)
731 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
675 675  
676 -2) Does it change with temperature, temperature will affect its measurement
733 +* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
734 +* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
677 677  
678 -3) If abnormal data occurs, you can turn on DEBUG mode, Please use downlink or AT COMMAN to enter DEBUG mode.
679 679  
680 -downlink command: (% style="color:blue" %)**F1 01**(%%), AT command: (% style="color:blue" %)**AT+DDEBUG=1**
737 +=== 3.3.8 Set Power Output Duration ===
681 681  
682 -4) After entering the debug mode, it will send 20 pieces of data at a time, and you can send its uplink to us for analysis
683 683  
684 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20230113135125-2.png?width=1057&height=136&rev=1.1||alt="image-20230113135125-2.png"]]
740 +Control the output duration 5V . Before each sampling, device will
685 685  
742 +~1. first enable the power output to external sensor,
686 686  
687 -Its original payload will be longer than other data. Even though it is being parsed, it can be seen that it is abnormal data.
744 +2. keep it on as per duration, read sensor value and construct uplink payload
688 688  
689 -Please send the data to us for check.
746 +3. final, close the power output.
690 690  
748 +(% style="color:blue" %)**AT Command: AT+5VT**
691 691  
692 -= 8. Order Info =
750 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
751 +|=(% style="width: 155px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3" %)**Response**
752 +|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
753 +OK
754 +|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
693 693  
756 +(% style="color:blue" %)**Downlink Command: 0x07**
694 694  
695 -Part Number: (% style="color:blue" %)**DDS45-LB-XXX**
758 +Format: Command Code (0x07) followed by 2 bytes.
696 696  
697 -(% style="color:red" %)**XXX**(%%): **The default frequency band**
760 +The first and second bytes are the time to turn on.
698 698  
762 +* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
763 +* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
764 +
765 +
766 += 4. Battery & Power Consumption =
767 +
768 +
769 +S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
770 +
771 +[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
772 +
773 +
774 += 5. OTA Firmware update =
775 +
776 +
777 +(% class="wikigeneratedid" %)
778 +User can change firmware S31x-LB to:
779 +
780 +* Change Frequency band/ region.
781 +* Update with new features.
782 +* Fix bugs.
783 +
784 +Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
785 +
786 +
787 +Methods to Update Firmware:
788 +
789 +* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
790 +* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
791 +
792 +
793 += 6. FAQ =
794 +
795 +
796 +
797 += 7. Order Info =
798 +
799 +
800 +Part Number: (% style="color:blue" %)**S31-LB-XX  / S31B-LB-XX**
801 +
802 +(% style="color:red" %)**XX**(%%): The default frequency band
803 +
699 699  * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
700 700  
701 701  * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
... ... @@ -712,12 +712,13 @@
712 712  
713 713  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
714 714  
715 -= 9. ​Packing Info =
716 716  
821 += 8. ​Packing Info =
717 717  
823 +
718 718  (% style="color:#037691" %)**Package Includes**:
719 719  
720 -* DDS45-LB LoRaWAN Distance Detection Sensor x 1
826 +* S31x-LB LoRaWAN Temperature & Humidity Sensor
721 721  
722 722  (% style="color:#037691" %)**Dimension and weight**:
723 723  
... ... @@ -729,9 +729,10 @@
729 729  
730 730  * Weight / pcs : g
731 731  
732 -= 10. Support =
733 733  
839 += 9. Support =
734 734  
841 +
735 735  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
736 736  
737 737  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].
image-20230530111051-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -85.1 KB
Content
image-20230530111412-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -85.0 KB
Content
image-20230530135919-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.6 KB
Content
image-20230530135929-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.6 KB
Content
image-20230530140053-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -1.3 MB
Content
image-20230612170349-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -164.2 KB
Content
image-20230612170943-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -86.4 KB
Content
image-20230612171032-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -86.4 KB
Content
image-20230613100900-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -184.0 KB
Content
image-20230613102426-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -89.3 KB
Content
image-20230613102459-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -89.3 KB
Content