Changes for page DS20L -- LoRaWAN Smart Distance Detector User Manual 01

Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 8 removed)
  • image-20230530111051-3.png
  • image-20230530111412-4.png
  • image-20230530135919-1.png
  • image-20230530135929-2.png
  • image-20230530140053-1.jpeg
  • image-20230612170349-1.png
  • image-20230612170943-2.png
  • image-20230612171032-3.png

Details

Page properties

Title

...	...	@@ -1,1 +1,1 @@
1		-DDS75-LB -- LoRaWAN Distance Detection Sensor User Manual
	1	+CPL03-LB -- LoRaWAN Pulse/Contact Sensor User Manual

Content

...	...	@@ -1,9 +1,7 @@
1	1	(% style="text-align:center" %)
2		-[[image:image-20230612170349-1.png||height="656" width="656"]]
	2	+[[image:image-20230530084608-2.jpeg||height="707" width="707"]]
3	3
4	4
5		-
6		-
7	7	**Table of Contents：**
8	8
9	9	{{toc/}}
...	...	@@ -15,76 +15,64 @@
15	15
16	16	= 1. Introduction =
17	17
18		-== 1.1 What is LoRaWAN Distance Detection Sensor ==
	16	+== 1.1 What is CPL03-LB LoRaWAN Pulse/Contact Sensor ==
19	19
20	20
21		-The Dragino DDS75-LB is a (% style="color:blue" %)** LoRaWAN Distance Detection Sensor**(%%) for Internet of Things solution. It is used to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses (% style="color:blue" %)** ultrasonic sensing technology**(%%) for (% style="color:blue" %)**distance measurement**(%%), and (% style="color:blue" %)** temperature compensation**(%%) is performed internally to improve the reliability of data. The DDS75-LB can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc.
	19	+The Dragino CPL03-LB is a (% style="color:blue" %)**LoRaWAN Contact Sensor**(%%) for Internet of Things solution. It detects dry contact status, open time, open counts, and then upload to IoT server via LoRaWAN wireless protocol.
22	22
23		-It detects the distance(% style="color:blue" %)**  between the measured object and the sensor**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
	21	+The CPL03-LB will send periodically data every day as well as for each dry contact action. It also counts the contact open times and calculate last open duration. User can also disable the uplink for each open/close event, instead, device can count each open event and uplink periodically.
24	24
25		-The LoRa wireless technology used in DDS75-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
	23	+The temperature & humidity sensor used in CPL03-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
26	26
27		-DDS75-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
	25	+The LoRa wireless technology used in CPL03-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
28	28
29		-DDS75-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
	27	+CPL03-LB (% style="color:blue" %)**supports open alarm feature**(%%), user can set open alarm for instant notice. CPL03-LB (% style="color:blue" %)**supports Datalog feature**, it can save the data when there is no LoRaWAN network and uplink when network recover.
30	30
31		-Each DDS75-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
	29	+CPL03-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
32	32
33		-[[image:image-20230612170943-2.png||height="525" width="912"]]
	31	+CPL03-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
34	34
	33	+Each CPL03-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
35	35
	35	+
36	36	== 1.2 ​Features ==
37	37
38	38
39	39	* LoRaWAN 1.0.3 Class A
40		-* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
41	41	* Ultra-low power consumption
42		-* Distance Detection by Ultrasonic technology
43		-* Flat object range 280mm - 7500mm
44		-* Accuracy: ±(1cm+S*0.3%) (S: Distance)
45		-* Cable Length : 25cm
	41	+* External 3 meters SHT31 probe (For S31-LB)
	42	+* Measure range -55°C ~~ 125°C
	43	+* Temperature & Humidity alarm
	44	+* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
46	46	* Support Bluetooth v5.1 and LoRaWAN remote configure
47	47	* Support wireless OTA update firmware
48		-* AT Commands to change parameters
	47	+* Uplink on periodically
49	49	* Downlink to change configure
50		-* IP66 Waterproof Enclosure
51	51	* 8500mAh Battery for long term use
52	52
	51	+
53	53	== 1.3 Specification ==
54	54
55	55
56		-(% style="color:#037691" %)**Rated environmental conditions:**
	55	+(% style="color:#037691" %)**Common DC Characteristics:**
57	57
58		-(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
59		-|(% style="background-color:#d9e2f3; color:#0070c0; width:163px" %)**Item**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)(((
60		-**Minimum value**
61		-)))|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)(((
62		-**Typical value**
63		-)))|(% style="background-color:#d9e2f3; color:#0070c0; width:87px" %)(((
64		-**Maximum value**
65		-)))|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**Unit**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Remarks**
66		-|(% style="width:174px" %)Storage temperature|(% style="width:86px" %)-25|(% style="width:66px" %)25|(% style="width:90px" %)80|(% style="width:48px" %)℃|(% style="width:203px" %)
67		-|(% style="width:174px" %)Storage humidity|(% style="width:86px" %) |(% style="width:66px" %)65%|(% style="width:90px" %)90%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
68		-|(% style="width:174px" %)Operating temperature|(% style="width:86px" %)-15|(% style="width:66px" %)25|(% style="width:90px" %)60|(% style="width:48px" %)℃|(% style="width:203px" %)
69		-|(% style="width:174px" %)Working humidity|(% style="width:86px" %)(((
70		-
	57	+* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
	58	+* Operating Temperature: -40 ~~ 85°C
71	71
72		-
73		-)))|(% style="width:66px" %)65%|(% style="width:90px" %)80%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
	60	+(% style="color:#037691" %)**Temperature Sensor:**
74	74
75		-(((
76		-(% style="color:red" %)**Remarks: (1) a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);       **
	62	+* Range: -40 to + 80°C
	63	+* Accuracy: ±0.2 @ 0-90 °C
	64	+* Resolution: 0.1°C
	65	+* Long Term Shift: <0.03 °C/yr
77	77
78		-(% style="color:red" %)** b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
	67	+(% style="color:#037691" %)**Humidity Sensor: **
79	79
80		-
81		-)))
	69	+* Range: 0 ~~ 99.9% RH
	70	+* Accuracy: ± 2%RH ( 0 ~~ 100%RH)
	71	+* Resolution: 0.01% RH
	72	+* Long Term Shift: <0.25 %RH/yr
82	82
83		-(% style="color:#037691" %)**Common DC Characteristics:**
84		-
85		-* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
86		-* Operating Temperature: -40 ~~ 85°C
87		-
88	88	(% style="color:#037691" %)**LoRa Spec:**
89	89
90	90	* Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
...	...	@@ -105,41 +105,16 @@
105	105	* Sleep Mode: 5uA @ 3.3v
106	106	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
107	107
108		-== 1.4 Effective measurement range Reference beam pattern ==
109	109
	95	+== 1.4 Sleep mode and working mode ==
110	110
111		-(% style="color:blue" %)**1. The tested object is a white cylindrical tube made of PVC, with a height of 100cm and a diameter of 7.5cm.**
112	112
113		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852253176-749.png?rev=1.1||alt="1654852253176-749.png"]]
114		-
115		-
116		-(% style="color:blue" %)**2. The object to be tested is a "corrugated cardboard box" perpendicular to the central axis of 0 °, and the length * width is 60cm * 50cm.**
117		-
118		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852175653-550.png?rev=1.1||alt="1654852175653-550.png"]]
119		-
120		-
121		-== 1.5 Applications ==
122		-
123		-
124		-* Horizontal distance measurement
125		-* Liquid level measurement
126		-* Parking management system
127		-* Object proximity and presence detection
128		-* Intelligent trash can management system
129		-* Robot obstacle avoidance
130		-* Automatic control
131		-* Sewer
132		-* Bottom water level monitoring
133		-
134		-== 1.6 Sleep mode and working mode ==
135		-
136		-
137	137	(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
138	138
139	139	(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
140	140
141	141
142		-== 1.7 Button & LEDs ==
	103	+== 1.5 Button & LEDs ==
143	143
144	144
145	145	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
...	...	@@ -158,12 +158,13 @@
158	158	)))
159	159	|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
160	160
161		-== 1.8 BLE connection ==
162	162
	123	+== 1.6 BLE connection ==
163	163
164		-DDS75-LB support BLE remote configure.
165	165
	126	+S31x-LB support BLE remote configure.
166	166
	128	+
167	167	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
168	168
169	169	* Press button to send an uplink
...	...	@@ -173,45 +173,56 @@
173	173	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
174	174
175	175
176		-== 1.9 Pin Definitions ==
	138	+== 1.7 Pin Definitions ==
177	177
178	178	[[image:image-20230523174230-1.png]]
179	179
180	180
	143	+== 1.8 Hardware Variant ==
181	181
182	182
183		-== 2.10 Mechanical ==
	146	+(% border="1" cellspacing="5" style="width:472px" %)
	147	+|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 187px; background-color:#D9E2F3;color:#0070C0" %)Probe Info
	148	+|(% style="width:102px" %)(((
	149	+S31-LB
	150	+)))|(% style="width:190px" %)[[image:image-20230527093214-2.jpeg]]|(% style="width:187px" %)(((
	151	+1 x SHT31 Probe
184	184
	153	+Cable Length : 2 meters
185	185
186		-[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
	155	+
	156	+)))
	157	+|(% style="width:102px" %)(((
	158	+S31B-LB
	159	+)))|(% style="width:190px" %)[[image:image-20230527093155-1.jpeg]]|(% style="width:187px" %)(((
	160	+1 x SHT31 Probe
187	187
	162	+Installed in device.
	163	+)))
188	188
189		-[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
	165	+(% style="display:none" %)
190	190
191	191
192		-[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
193	193
	169	+== 1.9 Mechanical ==
194	194
195		-(% style="color:blue" %)**Probe Mechanical:**
196	196
	172	+[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
197	197
198		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-1.png?rev=1.1||alt="image-20220610172003-1.png"]]
199	199
	175	+[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
200	200
201		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
202	202
	178	+[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
203	203
204		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
205	205
	181	+= 2. Configure S31x-LB to connect to LoRaWAN network =
206	206
207		-= 2. Configure DDS75-LB to connect to LoRaWAN network =
208		-
209	209	== 2.1 How it works ==
210	210
211	211
212		-The DDS75-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DDS75-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
	186	+The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
213	213
214		-(% style="display:none" %) (%%)
215	215
216	216	== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
217	217
...	...	@@ -218,15 +218,13 @@
218	218
219	219	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
220	220
221		-The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	194	+The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
222	222
223		-[[image:image-20230612171032-3.png||height="492" width="855"]](% style="display:none" %)
224	224
	197	+(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.
225	225
226		-(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DDS75-LB.
	199	+Each S31x-LB is shipped with a sticker with the default device EUI as below:
227	227
228		-Each DDS75-LB is shipped with a sticker with the default device EUI as below:
229		-
230	230	[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
231	231
232	232
...	...	@@ -254,10 +254,10 @@
254	254	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
255	255
256	256
257		-(% style="color:blue" %)**Step 2:**(%%) Activate on DDS75-LB
	228	+(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
258	258
259	259
260		-Press the button for 5 seconds to activate the DDS75-LB.
	231	+Press the button for 5 seconds to activate the S31x-LB.
261	261
262	262	(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
263	263
...	...	@@ -264,170 +264,174 @@
264	264	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
265	265
266	266
267		-== 2.3  ​Uplink Payload ==
	238	+== 2.3 ​Uplink Payload ==
268	268
	240	+=== 2.3.1 Device Status, FPORT~=5 ===
269	269
270		-(((
271		-DDS75-LB will uplink payload via LoRaWAN with below payload format:
272		-)))
273	273
274		-(((
275		-Uplink payload includes in total 8 bytes.
276		-)))
	243	+Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
277	277
278		-(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
279		-|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
280		-**Size(bytes)**
281		-)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)1|=(% style="background-color:#D9E2F3;color:#0070C0" %)2|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
282		-|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((
283		-[[Distance>>||anchor="H2.3.2A0Distance"]]
284		-(unit: mm)
285		-)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((
286		-[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]
287		-)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]
	245	+The Payload format is as below.
288	288
289		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850511545-399.png?rev=1.1||alt="1654850511545-399.png"]]
290	290
	248	+(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
	249	+|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
	250	+|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
	251	+|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
291	291
292		-=== 2.3.1  Battery Info ===
	253	+Example parse in TTNv3
293	293
	255	+[[image:image-20230524144422-1.png||height="174" width="1080"]]
294	294
295		-Check the battery voltage for DDS75-LB.
296	296
297		-Ex1: 0x0B45 = 2885mV
	258	+(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
298	298
299		-Ex2: 0x0B49 = 2889mV
	260	+(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
300	300
	262	+(% style="color:#037691" %)**Frequency Band**:
301	301
302		-=== 2.3.2  Distance ===
	264	+*0x01: EU868
303	303
	266	+*0x02: US915
304	304
305		-(((
306		-Get the distance. Flat object range 280mm - 7500mm.
307		-)))
	268	+*0x03: IN865
308	308
309		-(((
310		-For example, if the data you get from the register is 0x0B 0x05, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
	270	+*0x04: AU915
311	311
312		-(% style="color:#4472c4" %)**0B05(H) = 2821 (D) = 2821 mm.**
313		-)))
	272	+*0x05: KZ865
314	314
	274	+*0x06: RU864
315	315
316		-* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
317		-* If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. All value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
	276	+*0x07: AS923
318	318
	278	+*0x08: AS923-1
319	319
320		-=== 2.3.3  Interrupt Pin ===
	280	+*0x09: AS923-2
321	321
	282	+*0x0a: AS923-3
322	322
323		-This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
	284	+*0x0b: CN470
324	324
325		-**Example:**
	286	+*0x0c: EU433
326	326
327		-0x00: Normal uplink packet.
	288	+*0x0d: KR920
328	328
329		-0x01: Interrupt Uplink Packet.
	290	+*0x0e: MA869
330	330
331	331
332		-=== 2.3.4  DS18B20 Temperature sensor ===
	293	+(% style="color:#037691" %)**Sub-Band**:
333	333
	295	+AU915 and US915:value 0x00 ~~ 0x08
334	334
335		-This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
	297	+CN470: value 0x0B ~~ 0x0C
336	336
337		-**Example**:
	299	+Other Bands: Always 0x00
338	338
339		-If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
340	340
341		-If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
	302	+(% style="color:#037691" %)**Battery Info**:
342	342
	304	+Check the battery voltage.
343	343
344		-=== 2.3.5  Sensor Flag ===
	306	+Ex1: 0x0B45 = 2885mV
345	345
	308	+Ex2: 0x0B49 = 2889mV
346	346
347		-(((
348		-0x01: Detect Ultrasonic Sensor
349		-)))
350	350
351		-(((
352		-0x00: No Ultrasonic Sensor
	311	+=== 2.3.2  Sensor Data. FPORT~=2 ===
	312	+
	313	+
	314	+Sensor Data is uplink via FPORT=2
	315	+
	316	+(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
	317	+|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
	318	+**Size(bytes)**
	319	+)))|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)**2**|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
	320	+|(% style="width:99px" %)Value|(% style="width:69px" %)(((
	321	+Battery
	322	+)))|(% style="width:130px" %)(((
	323	+Unix TimeStamp
	324	+)))|(% style="width:194px" %)(((
	325	+Alarm Flag & MOD& Level of PA8
	326	+)))|(% style="width:106px" %)(((
	327	+Temperature
	328	+)))|(% style="width:97px" %)(((
	329	+Humidity
353	353	)))
354	354
	332	+[[image:image-20230524144456-2.png||height="180" width="1142"]]
355	355
356		-=== 2.3.6  Decode payload in The Things Network ===
357	357
	335	+==== (% style="color:#4472c4" %)**Battery**(%%) ====
358	358
359		-While using TTN network, you can add the payload format to decode the payload.
	337	+Sensor Battery Level.
360	360
361		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850829385-439.png?rev=1.1||alt="1654850829385-439.png"]]
	339	+Ex1: 0x0B45 = 2885mV
362	362
363		-The payload decoder function for TTN V3 is here:
	341	+Ex2: 0x0B49 = 2889mV
364	364
365		-(((
366		-DDS75-LB TTN V3 Payload Decoder:  [[ttps:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
367		-)))
368	368
369	369
370		-== 2.4  Uplink Interval ==
	345	+==== (% style="color:#4472c4" %)**Temperature**(%%) ====
371	371
	347	+**Example**:
372	372
373		-The DDS75-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
	349	+If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
374	374
	351	+If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
375	375
376		-== 2.5  ​Show Data in DataCake IoT Server ==
	353	+（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
377	377
378	378
379		-(((
380		-[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
381		-)))
	356	+==== (% style="color:#4472c4" %)**Humidity**(%%) ====
382	382
383		-(((
384		-
385		-)))
386	386
387		-(((
388		-(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
389		-)))
	359	+Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
390	390
391		-(((
392		-(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
393		-)))
394	394
	362	+==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
395	395
396		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592790040-760.png?rev=1.1||alt="1654592790040-760.png"]]
397	397
	365	+**Example:**
398	398
399		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592800389-571.png?rev=1.1||alt="1654592800389-571.png"]]
	367	+If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
400	400
	369	+If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
401	401
402		-(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
	371	+If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
403	403
404		-(% style="color:blue" %)**Step 4**(%%)**: Search the DDS75-LB and add DevEUI.**
	373	+If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
405	405
406		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
	375	+If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
407	407
	377	+If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail.
408	408
409		-After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake.
410	410
411		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
	380	+== 2.4 Payload Decoder file ==
412	412
413	413
	383	+In TTN, use can add a custom payload so it shows friendly reading
414	414
415		-== 2.6 Datalog Feature ==
	385	+In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
416	416
	387	+[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
417	417
418		-Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DDS75-LB will store the reading for future retrieving purposes.
419	419
	390	+== 2.5 Datalog Feature ==
420	420
421		-=== 2.6.1 Ways to get datalog via LoRaWAN ===
422	422
	393	+Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
423	423
424		-Set PNACKMD=1, DDS75-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DDS75-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
425	425
	396	+=== 2.5.1 Ways to get datalog via LoRaWAN ===
	397	+
	398	+
	399	+Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
	400	+
426	426	* (((
427		-a) DDS75-LB will do an ACK check for data records sending to make sure every data arrive server.
	402	+a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
428	428	)))
429	429	* (((
430		-b) DDS75-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but DDS75-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DDS75-LB gets a ACK, DDS75-LB will consider there is a network connection and resend all NONE-ACK messages.
	405	+b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
431	431	)))
432	432
433	433	Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
...	...	@@ -435,10 +435,10 @@
435	435	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
436	436
437	437
438		-=== 2.6.2 Unix TimeStamp ===
	413	+=== 2.5.2 Unix TimeStamp ===
439	439
440	440
441		-DDS75-LB uses Unix TimeStamp format based on
	416	+S31x-LB uses Unix TimeStamp format based on
442	442
443	443	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
444	444
...	...	@@ -452,64 +452,147 @@
452	452	So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
453	453
454	454
455		-=== 2.6.3 Set Device Time ===
	430	+=== 2.5.3 Set Device Time ===
456	456
457	457
458	458	User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
459	459
460		-Once DDS75-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to DDS75-LB. If DDS75-LB fails to get the time from the server, DDS75-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
	435	+Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
461	461
462	462	(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
463	463
464	464
465		-=== 2.6.4 Poll sensor value ===
	440	+=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
466	466
467	467
468		-Users can poll sensor values based on timestamps. Below is the downlink command.
	443	+The Datalog uplinks will use below payload format.
469	469
470		-(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
471		-|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
472		-|(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
473		-|(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
	445	+**Retrieval data payload:**
474	474
	447	+(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
	448	+|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
	449	+**Size(bytes)**
	450	+)))|=(% style="width: 40px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 65px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px; background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 100px; background-color:#D9E2F3;color:#0070C0" %)**4**
	451	+|(% style="width:103px" %)Value|(% style="width:68px" %)(((
	452	+ignore
	453	+)))|(% style="width:104px" %)(((
475	475	(((
476		-Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
	455	+Humidity
477	477	)))
478	478
479	479	(((
480		-For example, downlink command [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20220518162852-1.png?rev=1.1||alt="image-20220518162852-1.png"]]
	459	+
481	481	)))
	461	+)))|(% style="width:87px" %)(((
	462	+Temperature
	463	+)))|(% style="width:178px" %)(((
	464	+Poll message flag & Alarm Flag& Level of PA8
	465	+)))|(% style="width:137px" %)Unix Time Stamp
482	482
	467	+**Poll message flag & Alarm Flag & Level of PA8:**
	468	+
	469	+[[image:image-20230524114302-1.png||height="115" width="736"]]
	470	+
	471	+
	472	+**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
	473	+
	474	+**Poll Message Flag**: 1: This message is a poll message reply.
	475	+
	476	+* Poll Message Flag is set to 1.
	477	+
	478	+* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
	479	+
	480	+For example, in US915 band, the max payload for different DR is:
	481	+
	482	+**a) DR0:** max is 11 bytes so one entry of data
	483	+
	484	+**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
	485	+
	486	+**c) DR2:** total payload includes 11 entries of data
	487	+
	488	+**d) DR3: **total payload includes 22 entries of data.
	489	+
	490	+If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0
	491	+
	492	+**Example:**
	493	+
	494	+If S31x-LB has below data inside Flash:
	495	+
	496	+[[image:image-20230524114654-2.png]]
	497	+
	498	+
	499	+If user sends below downlink command: 31646D84E1646D856C05
	500	+
	501	+Where : Start time: 646D84E1 = time 23/5/24 03:30:41
	502	+
	503	+ Stop time: 646D856C= time 23/5/24 03:33:00
	504	+
	505	+
	506	+**S31x-LB will uplink this payload.**
	507	+
	508	+[[image:image-20230524114826-3.png||height="448" width="1244"]]
	509	+
483	483	(((
484		-Is to check 2021/11/12 12:00:00 to 2021/11/12 15:00:00's data
	511	+00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
485	485	)))
486	486
487	487	(((
488		-Uplink Internal =5s，means DDS75-LB will send one packet every 5s. range 5~~255s.
	515	+Where the first 11 bytes is for the first entry:
489	489	)))
490	490
	518	+(((
	519	+00 00 02 36 01 10 40 64 6D 84 E1
	520	+)))
491	491
	522	+(((
	523	+**Hum**=0x0236/10=56.6
	524	+)))
	525	+
	526	+(((
	527	+**Temp**=0x0110/10=27.2
	528	+)))
	529	+
	530	+(((
	531	+**poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
	532	+)))
	533	+
	534	+(((
	535	+**Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
	536	+)))
	537	+
	538	+
	539	+(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
	540	+
	541	+== 2.6 Temperature Alarm Feature ==
	542	+
	543	+
	544	+S31x-LB work flow with Alarm feature.
	545	+
	546	+
	547	+[[image:image-20230524110125-3.png||height="768" width="1115"]]
	548	+
	549	+
	550	+
492	492	== 2.7 Frequency Plans ==
493	493
494	494
495		-The DDS75-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	554	+The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
496	496
497	497	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
498	498
499	499
500		-= 3. Configure DDS75-LB =
	559	+= 3. Configure S31x-LB =
501	501
502	502	== 3.1 Configure Methods ==
503	503
504	504
505		-DDS75-LB supports below configure method:
	564	+S31x-LB supports below configure method:
506	506
507	507	* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
508		-
509	509	* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
510		-
511	511	* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
512	512
	570	+
513	513	== 3.2 General Commands ==
514	514
515	515
...	...	@@ -516,7 +516,6 @@
516	516	These commands are to configure:
517	517
518	518	* General system settings like: uplink interval.
519		-
520	520	* LoRaWAN protocol & radio related command.
521	521
522	522	They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
...	...	@@ -524,25 +524,21 @@
524	524	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
525	525
526	526
527		-== 3.3 Commands special design for DDS75-LB ==
	584	+== 3.3 Commands special design for S31x-LB ==
528	528
529	529
530		-These commands only valid for DDS75-LB, as below:
	587	+These commands only valid for S31x-LB, as below:
531	531
532	532
533	533	=== 3.3.1 Set Transmit Interval Time ===
534	534
535	535
536		-(((
537	537	Feature: Change LoRaWAN End Node Transmit Interval.
538		-)))
539	539
540		-(((
541	541	(% style="color:blue" %)**AT Command: AT+TDC**
542		-)))
543	543
544	544	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
545		-|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
	598	+|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**
546	546	|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
547	547	30000
548	548	OK
...	...	@@ -553,154 +553,201 @@
553	553	Set transmit interval to 60000ms = 60 seconds
554	554	)))
555	555
556		-(((
557	557	(% style="color:blue" %)**Downlink Command: 0x01**
558		-)))
559	559
560		-(((
561	561	Format: Command Code (0x01) followed by 3 bytes time value.
562		-)))
563	563
564		-(((
565	565	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
566		-)))
567	567
568		-* (((
569		-Example 1: Downlink Payload: 0100001E  ~/~/ Set Transmit Interval (TDC) = 30 seconds
570		-)))
571		-* (((
572		-Example 2: Downlink Payload: 0100003C  ~/~/ Set Transmit Interval (TDC) = 60 seconds
573		-)))
	615	+* Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
	616	+* Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
574	574
575		-=== 3.3.2 Set Interrupt Mode ===
576	576
	619	+=== 3.3.2 Get Device Status ===
577	577
578		-Feature, Set Interrupt mode for PA8 of pin.
579	579
580		-When AT+INTMOD=0 is set, PA8 is used as a digital input port.
	622	+Send a LoRaWAN downlink to ask device send Alarm settings.
581	581
582		-(% style="color:blue" %)**AT Command: AT+INTMOD**
	624	+(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
583	583
584		-(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
585		-|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
586		-|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
587		-0
588		-OK
589		-the mode is 0 =Disable Interrupt
590		-)))
591		-|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
592		-Set Transmit Interval
593		-0. (Disable Interrupt),
594		-~1. (Trigger by rising and falling edge)
595		-2. (Trigger by falling edge)
596		-3. (Trigger by rising edge)
597		-)))|(% style="width:157px" %)OK
	626	+Sensor will upload Device Status via FPORT=5. See payload section for detail.
598	598
599		-(% style="color:blue" %)**Downlink Command: 0x06**
600	600
601		-Format: Command Code (0x06) followed by 3 bytes.
	629	+=== 3.3.3 Set Temperature Alarm Threshold ===
602	602
603		-This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
604	604
605		-* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
	632	+* (% style="color:blue" %)**AT Command:**
606	606
607		-* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
	634	+(% style="color:#037691" %)**AT+SHTEMP=min,max**
608	608
609		-= 4. Battery & Power Consumption =
	636	+* When min=0, and max≠0, Alarm higher than max
	637	+* When min≠0, and max=0, Alarm lower than min
	638	+* When min≠0 and max≠0, Alarm higher than max or lower than min
610	610
	640	+Example:
611	611
612		-DDS75-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
	642	+ AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
613	613
614		-[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
	644	+* (% style="color:blue" %)**Downlink Payload:**
615	615
	646	+(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
616	616
617		-= 5. OTA Firmware update =
	648	+(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
618	618
619	619
620		-(% class="wikigeneratedid" %)
621		-User can change firmware DDS75-LB to:
	651	+=== 3.3.4 Set Humidity Alarm Threshold ===
622	622
623		-* Change Frequency band/ region.
624	624
625		-* Update with new features.
	654	+* (% style="color:blue" %)**AT Command:**
626	626
627		-* Fix bugs.
	656	+(% style="color:#037691" %)**AT+SHHUM=min,max**
628	628
629		-Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/7la95mae0fn03xe/AACtzs-32m22TLb75B-iIr-Qa?dl=0]]**
	658	+* When min=0, and max≠0, Alarm higher than max
	659	+* When min≠0, and max=0, Alarm lower than min
	660	+* When min≠0 and max≠0, Alarm higher than max or lower than min
630	630
631		-Methods to Update Firmware:
	662	+Example:
632	632
633		-* (Recommanded way) OTA firmware update via wireless:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	664	+ AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
634	634
635		-* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
	666	+* (% style="color:blue" %)**Downlink Payload:**
636	636
637		-= 6. FAQ =
	668	+(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
638	638
	670	+(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
639	639
640		-== 6.1  What is the frequency plan for DDS75-LB? ==
641	641
	673	+=== 3.3.5 Set Alarm Interval ===
642	642
643		-DDS75-LB use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
644	644
	676	+The shortest time of two Alarm packet. (unit: min)
645	645
646		-== 6.2  Can I use DDS75-LB in condensation environment? ==
	678	+* (% style="color:blue" %)**AT Command:**
647	647
	680	+(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
648	648
649		-DDS75-LB is not suitable to be used in condensation environment. Condensation on the DDS75-LB probe will affect the reading and always got 0.
	682	+* (% style="color:blue" %)**Downlink Payload:**
650	650
	684	+(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
651	651
652		-= 7.  Trouble Shooting =
653	653
654		-== 7.1  Why I can't join TTN V3 in US915 / AU915 bands? ==
	687	+=== 3.3.6 Get Alarm settings ===
655	655
656	656
657		-It is due to channel mapping. Please see below link:  [[Frequency band>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]]
	690	+Send a LoRaWAN downlink to ask device send Alarm settings.
658	658
	692	+* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
659	659
660		-== 7.2  AT Command input doesn't work ==
	694	+**Example:**
661	661
	696	+[[image:image-20230524110211-4.png]]
662	662
663		-In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:blue" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:blue" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
	698	+**Explain:**
664	664
	700	+* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
665	665
666		-== 7.3  Why does the sensor reading show 0 or "No sensor" ==
667	667
	703	+=== 3.3.7 Set Interrupt Mode ===
668	668
669		-~1. The measurement object is very close to the sensor, but in the blind spot of the sensor.
670	670
671		-2. Sensor wiring is disconnected
	706	+Feature, Set Interrupt mode for PA8 of pin.
672	672
673		-3. Not using the correct decoder
	708	+When AT+INTMOD=0 is set, PA8 is used as a digital input port.
674	674
	710	+(% style="color:blue" %)**AT Command: AT+INTMOD**
675	675
676		-== 7.4  Abnormal readings The gap between multiple readings is too large or the gap between the readings and the actual value is too large ==
	712	+(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
	713	+|=(% style="width: 155px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3" %)**Response**
	714	+|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
	715	+0
	716	+OK
	717	+the mode is 0 =Disable Interrupt
	718	+)))
	719	+|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
	720	+Set Transmit Interval
	721	+0. (Disable Interrupt),
	722	+~1. (Trigger by rising and falling edge)
	723	+2. (Trigger by falling edge)
	724	+3. (Trigger by rising edge)
	725	+)))|(% style="width:157px" %)OK
677	677
	727	+(% style="color:blue" %)**Downlink Command: 0x06**
678	678
679		-1) Please check if there is something on the probe affecting its measurement (condensed water, volatile oil, etc.)
	729	+Format: Command Code (0x06) followed by 3 bytes.
680	680
681		-2) Does it change with temperature, temperature will affect its measurement
	731	+This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
682	682
683		-3) If abnormal data occurs, you can turn on DEBUG mode, Please use downlink or AT COMMAN to enter DEBUG mode.
	733	+* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
	734	+* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
684	684
685		-downlink command: (% style="color:blue" %)**F1 01**(%%), AT command: (% style="color:blue" %)**AT+DDEBUG=1**
686	686
687		-4) After entering the debug mode, it will send 20 pieces of data at a time, and you can send its uplink to us for analysis
	737	+=== 3.3.8 Set Power Output Duration ===
688	688
689		-[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20230113135125-2.png?width=1057&height=136&rev=1.1||alt="image-20230113135125-2.png"]]
690	690
	740	+Control the output duration 5V . Before each sampling, device will
691	691
692		-Its original payload will be longer than other data. Even though it is being parsed, it can be seen that it is abnormal data.
	742	+~1. first enable the power output to external sensor,
693	693
694		-Please send the data to us for check.
	744	+2. keep it on as per duration, read sensor value and construct uplink payload
695	695
	746	+3. final, close the power output.
696	696
697		-= 8. Order Info =
	748	+(% style="color:blue" %)**AT Command: AT+5VT**
698	698
	750	+(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
	751	+|=(% style="width: 155px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3" %)**Response**
	752	+|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
	753	+OK
	754	+|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
699	699
700		-Part Number: (% style="color:blue" %)**DDS75-LB-XXX**
	756	+(% style="color:blue" %)**Downlink Command: 0x07**
701	701
702		-(% style="color:red" %)**XXX**(%%): **The default frequency band**
	758	+Format: Command Code (0x07) followed by 2 bytes.
703	703
	760	+The first and second bytes are the time to turn on.
	761	+
	762	+* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
	763	+* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
	764	+
	765	+
	766	+= 4. Battery & Power Consumption =
	767	+
	768	+
	769	+S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
	770	+
	771	+[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
	772	+
	773	+
	774	+= 5. OTA Firmware update =
	775	+
	776	+
	777	+(% class="wikigeneratedid" %)
	778	+User can change firmware S31x-LB to:
	779	+
	780	+* Change Frequency band/ region.
	781	+* Update with new features.
	782	+* Fix bugs.
	783	+
	784	+Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
	785	+
	786	+
	787	+Methods to Update Firmware:
	788	+
	789	+* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	790	+* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
	791	+
	792	+
	793	+= 6. FAQ =
	794	+
	795	+
	796	+
	797	+= 7. Order Info =
	798	+
	799	+
	800	+Part Number: (% style="color:blue" %)**S31-LB-XX  / S31B-LB-XX**
	801	+
	802	+(% style="color:red" %)**XX**(%%): The default frequency band
	803	+
704	704	* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
705	705
706	706	* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
...	...	@@ -718,12 +718,12 @@
718	718	* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
719	719
720	720
721		-= 9. ​Packing Info =
	821	+= 8. ​Packing Info =
722	722
723	723
724	724	(% style="color:#037691" %)**Package Includes**:
725	725
726		-* DDS75-LB LoRaWAN Distance Detection Sensor x 1
	826	+* S31x-LB LoRaWAN Temperature & Humidity Sensor
727	727
728	728	(% style="color:#037691" %)**Dimension and weight**:
729	729
...	...	@@ -736,7 +736,7 @@
736	736	* Weight / pcs : g
737	737
738	738
739		-= 10. Support =
	839	+= 9. Support =
740	740
741	741
742	742	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

image-20230530111051-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-85.1 KB

Content

image-20230530111412-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-85.0 KB

Content

image-20230530135919-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-87.6 KB

Content

image-20230530135929-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-87.6 KB

Content

image-20230530140053-1.jpeg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-1.3 MB

Content

image-20230612170349-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-164.2 KB

Content

image-20230612170943-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-86.4 KB

Content

image-20230612171032-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-86.4 KB

Content