Changes for page DS20L -- LoRaWAN Smart Distance Detector User Manual 01

Last modified by Mengting Qiu on 2023/12/14 11:15

From 70.3 to 70.2 From 70.12 to 70.11

From version 70.11

edited by Xiaoling
on 2023/06/12 18:09

Change comment: There is no comment for this version

To version 70.3

edited by Xiaoling
on 2023/06/12 17:11

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -18,10 +18,12 @@
  == 1.1 What is LoRaWAN Distance Detection Sensor ==
--The Dragino DDS75-LB is a (% style="color:blue" %)** LoRaWAN Distance Detection Sensor**(%%) for Internet of Things solution. It is used to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses (% style="color:blue" %)** ultrasonic sensing technology**(%%) for (% style="color:blue" %)**distance measurement**(%%), and (% style="color:blue" %)** temperature compensation**(%%) is performed internally to improve the reliability of data. The DDS75-LB can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc.
++The Dragino SW3L-LB is a (% style="color:blue" %)**LoRaWAN Flow Sensor**(%%). It detects water flow volume and uplink to IoT server via LoRaWAN network. User can use this to(% style="color:blue" %)** monitor the water usage for buildings.**
--It detects the distance(% style="color:blue" %)**  between the measured object and the sensor**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
++The SW3L-LB will send water flow volume every 20 minutes. It can also (% style="color:blue" %)**detect the water flow status**(%%) and (% style="color:blue" %)**send Alarm**(%%), to avoid the waste for water usage such as broken toilet case.
++SW3L-LB is designed for both indoor and outdoor use. It has a weatherproof enclosure and industrial level battery to work in low to high temperatures.
++
  The LoRa wireless technology used in SW3L-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
  SW3L-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
@@ -39,47 +39,20 @@
  * LoRaWAN 1.0.3 Class A
  * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
  * Ultra-low power consumption
--* Distance Detection by Ultrasonic technology
--* Flat object range 280mm - 7500mm
--* Accuracy: ±(1cm+S*0.3%) (S: Distance)
--* Cable Length : 25cm
++* Upload water flow volume
++* Monitor water waste
++* AT Commands to change parameters
++* supports Datalog feature
  * Support Bluetooth v5.1 and LoRaWAN remote configure
  * Support wireless OTA update firmware
--* AT Commands to change parameters
++* Uplink on periodically and open/close event
  * Downlink to change configure
--* IP66 Waterproof Enclosure
  * 8500mAh Battery for long term use
++
  == 1.3 Specification ==
--(% style="color:#037691" %)**Rated environmental conditions:**
--
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:163px" %)**Item**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)(((
--**Minimum value**
--)))|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)(((
--**Typical value**
--)))|(% style="background-color:#d9e2f3; color:#0070c0; width:87px" %)(((
--**Maximum value**
--)))|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**Unit**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Remarks**
--|(% style="width:174px" %)Storage temperature|(% style="width:86px" %)-25|(% style="width:66px" %)25|(% style="width:90px" %)80|(% style="width:48px" %)℃|(% style="width:203px" %)
--|(% style="width:174px" %)Storage humidity|(% style="width:86px" %) |(% style="width:66px" %)65%|(% style="width:90px" %)90%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
--|(% style="width:174px" %)Operating temperature|(% style="width:86px" %)-15|(% style="width:66px" %)25|(% style="width:90px" %)60|(% style="width:48px" %)℃|(% style="width:203px" %)
--|(% style="width:174px" %)Working humidity|(% style="width:86px" %)(((
--
--
--
--)))|(% style="width:66px" %)65%|(% style="width:90px" %)80%|(% style="width:48px" %)RH|(% style="width:203px" %)(1)
--
--(((
--**Remarks: (1)  a. When the ambient temperature is 0-39 ℃, the maximum humidity is 90% (non-condensing);       **
--
--**~                       b. When the ambient temperature is 40-50 ℃, the highest humidity is the highest humidity in the natural world at the current temperature (no condensation)**
--
--
--)))
--
  (% style="color:#037691" %)**Common DC Characteristics:**
  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
@@ -105,41 +105,25 @@
  * Sleep Mode: 5uA @ 3.3v
  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
--== 1.4 Effective measurement range Reference beam pattern ==
++== 1.4 Applications ==
--**~1. The tested object is a white cylindrical tube made of PVC, with a height of 100cm and a diameter of 7.5cm.**
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852253176-749.png?rev=1.1||alt="1654852253176-749.png"]]
++* Flow Sensor application
++* Water Control
++* Toilet Flow Sensor
++* Monitor Waste water
--**2. The object to be tested is a "corrugated cardboard box" perpendicular to the central axis of 0 °, and the length * width is 60cm * 50cm.**
++== 1.5 Sleep mode and working mode ==
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654852175653-550.png?rev=1.1||alt="1654852175653-550.png"]]
--
--== 1.5 Applications ==
--
--
--* Horizontal distance measurement
--* Liquid level measurement
--* Parking management system
--* Object proximity and presence detection
--* Intelligent trash can management system
--* Robot obstacle avoidance
--* Automatic control
--* Sewer
--* Bottom water level monitoring
--
--== 1.6 Sleep mode and working mode ==
--
--
  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
--== 1.7 Button & LEDs ==
++== 1.6 Button & LEDs ==
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
@@ -158,12 +158,13 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
--== 1.8 BLE connection ==
++== 1.7 BLE connection ==
--DDS75-LB support BLE remote configure.
++SW3L-LB support BLE remote configure.
++
  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
  * Press button to send an uplink
@@ -173,13 +173,24 @@
  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
--== 1.9 Pin Definitions ==
++== 1.8 Pin Definitions ==
  [[image:image-20230523174230-1.png]]
--==   ==
++== 1.9 Flow Sensor Spec ==
++
++(((
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Model**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Probe**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Diameter**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Range**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Max Pressure**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Measure**
++|(% style="width:88px" %)SW3L-004|(% style="width:75px" %)DW-004|(% style="width:107px" %)G1/2" /DN15|(% style="width:101px" %)1~~30L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)450 pulse = 1 L
++|(% style="width:88px" %)SW3L-006|(% style="width:75px" %)DW-006|(% style="width:107px" %)G3/4" /DN20|(% style="width:101px" %)1~~60L/min|(% style="width:116px" %)≤ 1.2Mpa|(% style="width:124px" %)390 pulse = 1 L
++|(% style="width:88px" %)SW3L-010|(% style="width:75px" %)DW-010|(% style="width:107px" %)G 1" /DN25|(% style="width:101px" %)2~~100L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)64 pulse = 1 L
++)))
++
++
++
  == 2.10 Mechanical ==
@@ -192,24 +192,27 @@
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
--**Probe Mechanical:**
++(% style="color:blue" %)**DW-004 Flow Sensor: diameter: G1/2” / DN15.  450 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091350-1.png?width=722&height=385&rev=1.1||alt="image-20220519091350-1.png"]]
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-1.png?rev=1.1||alt="image-20220610172003-1.png"]]
++(% style="color:blue" %)**006: DW-006 Flow Sensor: diameter: G3/4” / DN20.  390 pulse = 1 L**
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-2.png?width=723&height=258&rev=1.1||alt="image-20220519091423-2.png"]]
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610172003-2.png?rev=1.1||alt="image-20220610172003-2.png"]]
++(% style="color:blue" %)**010: DW-010 Flow Sensor: diameter: G 1” / DN25.   64 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-3.png?width=724&height=448&rev=1.1||alt="image-20220519091423-3.png"]]
--= 2. Configure DDS75-LB to connect to LoRaWAN network =
++= 2. Configure SW3L-LB to connect to LoRaWAN network =
++
  == 2.1 How it works ==
--The DDS75-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DDS75-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
++The SW3L-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the SW3L-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
  (% style="display:none" %) (%%)
@@ -223,9 +223,9 @@
  [[image:image-20230612171032-3.png||height="492" width="855"]](% style="display:none" %)
--(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DDS75-LB.
++(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SW3L-LB.
--Each DDS75-LB is shipped with a sticker with the default device EUI as below:
++Each SW3L-LB is shipped with a sticker with the default device EUI as below:
  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
@@ -254,10 +254,10 @@
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
--(% style="color:blue" %)**Step 2:**(%%) Activate on DDS75-LB
++(% style="color:blue" %)**Step 2:**(%%) Activate on SW3L-LB
--Press the button for 5 seconds to activate the DDS75-LB.
++Press the button for 5 seconds to activate the SW3L-LB.
  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
@@ -264,178 +264,355 @@
  After join success, it will start to upload messages to TTN and you can see the messages in the panel.
--== 2.3  Uplink Payload ==
++== 2.3 Uplink Payload ==
++=== 2.3.1 Device Status, FPORT~=5 ===
++
++Include device configure status. Once SW3L-LB Joined the network, it will uplink this message to the server. After that, SW3L-LB will uplink Device Status every 12 hours.
++
++Users can use the downlink command(**0x26 01**) to ask SW3L-LB to send device configure detail, include device configure status. SW3L-LB will uplink a payload via FPort=5 to server.
++
++The Payload format is as below.
++
++
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
++|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
++|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
++
++Example parse in TTNv3
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652925144491-755.png?width=732&height=139&rev=1.1||alt="1652925144491-755.png"]]
++
++
++(% style="color:#037691" %)**Sensor Model**(%%): For SW3L-LB, this value is 0x11
++
++(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
++
++(% style="color:#037691" %)**Frequency Band**:
++
++*0x01: EU868
++
++*0x02: US915
++
++*0x03: IN865
++
++*0x04: AU915
++
++*0x05: KZ865
++
++*0x06: RU864
++
++*0x07: AS923
++
++*0x08: AS923-1
++
++*0x09: AS923-2
++
++*0x0a: AS923-3
++
++*0x0b: CN470
++
++*0x0c: EU433
++
++*0x0d: KR920
++
++*0x0e: MA869
++
++
++(% style="color:#037691" %)**Sub-Band**:
++
++AU915 and US915:value 0x00 ~~ 0x08
++
++CN470: value 0x0B ~~ 0x0C
++
++Other Bands: Always 0x00
++
++
++(% style="color:#037691" %)**Battery Info**:
++
++Check the battery voltage.
++
++Ex1: 0x0B45 = 2885mV
++
++Ex2: 0x0B49 = 2889mV
++
++
++=== 2.3.2 Sensor Configuration, FPORT~=4 ===
++
++
++SW3L-LB will only send this command after getting the downlink command (0x26 02) from the server.
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %) **Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:105px" %)**3**|(% style="background-color:#d9e2f3; color:#0070c0; width:60px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:96px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:105px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:74px" %)**1**
++|**Value**|(% style="width:104px" %)TDC(unit:sec)|(% style="width:43px" %)N/A|(% style="width:91px" %)Stop Timer|(% style="width:100px" %)Alarm Timer|(% style="width:69px" %)Reserve
++
++* (% style="color:#037691" %)**TDC: (default: 0x0004B0)**
++
++Uplink interval for the total pulse count, default value is 0x0004B0 which is 1200 seconds = 20 minutes.
++
++
++* (% style="color:#037691" %)**STOP Duration & Alarm Timer**
++
++Shows the configure value of [[Alarm for continuously water flow>>||anchor="H3.3.4Alarmforcontinuouslywaterflow"]]
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095747-2.png?width=723&height=113&rev=1.1||alt="image-20220519095747-2.png"]]
++
++
++=== 2.3.3 Water Flow Value, Uplink FPORT~=2 ===
++
++
  (((
--(((
--DDS75-LB will uplink payload via LoRaWAN with below payload format:
++SW3L-LB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And SW3L-LB will:
  )))
  (((
--Uplink payload includes in total 4 bytes.
--Payload for firmware version v1.1.4. . Before v1.1.3, there is on two fields: BAT and Distance
++periodically send this uplink every 20 minutes, this interval [[can be changed>>||anchor="H3.3.1SetTransmitIntervalTime"]].
  )))
--)))
  (((
--
++Uplink Payload totals 11 bytes.
  )))
  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
--**Size(bytes)**
--)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)1|=(% style="background-color:#D9E2F3;color:#0070C0" %)2|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
--|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((
--[[Distance>>||anchor="H2.3.2A0Distance"]]
--(unit: mm)
--)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((
--[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]
--)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]
++|=(% colspan="6" style="width: 510px;background-color:#D9E2F3;color:#0070C0" %)**Water Flow Value,  FPORT=2**
++|(% style="width:60px" %)**Size(bytes)**|(% style="width:130px" %)**1**|(% style="width:130px" %)**4**|(% style="width:30px" %)**1**|(% style="width:50px" %)**1**|(% style="width:80px" %)**4**
++|(% style="width:110px" %)**Value**|(% style="width:81px" %)Calculate Flag  & [[Alarm>>||anchor="H3.3.4Alarmforcontinuouslywaterflow"]]|(% style="width:95px" %)(((
++Total pulse Or Last Pulse
++)))|(% style="width:55px" %)MOD|(% style="width:115px" %)Reserve(0x01)|(% style="width:129px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850511545-399.png?rev=1.1||alt="1654850511545-399.png"]]
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:470px" %)
++|=(% colspan="4" style="width: 470px;background-color:#D9E2F3;color:#0070C0" %)**Status & Alarm field**
++|(% style="width:60px" %)**Size(bit)**|(% style="width:80px" %)**6**|(% style="width:310px" %)**1**|(% style="width:20px" %)**1**
++|(% style="width:88px" %)**Value**|(% style="width:117px" %)Calculate Flag|(% style="width:221px" %)Alarm: 0: No Alarm; 1: Alarm|(% style="width:64px" %)N/A
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-3.png?width=736&height=284&rev=1.1||alt="image-20220519095946-3.png"]]
--=== 2.3.1  Battery Info ===
++* (((
++(% style="color:#037691" %)**Calculate Flag**
++)))
--Check the battery voltage for DDS75-LB.
++(((
++The calculate flag is a user defined field, IoT server can use this flag to handle different meters with different pulse factors. For example, if there are 100 Flow Sensors, meters 1 ~~50 are 1 liter/pulse and meters 51 ~~ 100 has 1.5 liter/pulse.
++)))
--Ex1: 0x0B45 = 2885mV
++(((
++**Example: in the default payload:**
++)))
--Ex2: 0x0B49 = 2889mV
++* (((
++calculate flag=0: for SW3L-004 Flow Sensor: 450 pulse = 1 L
++)))
++* (((
++calculate flag=1: for SW3L-006 Flow Sensor: 390 pulse = 1 L
++)))
++* (((
++calculate flag=2: for SW3L-010 Flow Sensor: 64 pulse = 1 L
++)))
++(((
++Default value: 0.
++)))
--=== 2.3.2  Distance ===
++(((
++Range (6 bits): (b)000000 ~~ (b) 111111
++If user use with a meter for example is 0.02L/pulse. To proper decode the correct value in server,
--(((
--Get the distance. Flat object range 280mm - 7500mm.
++1) User can set the Calculate Flag of this sensor to 3.
++
++2) In server side, when a sensor data arrive, the decoder will check the value of Calculate Flag, It the value is 3, the total volume = 0.02 x Pulse Count.
  )))
  (((
--For example, if the data you get from the register is 0x0B 0x05, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
++(% style="color:red" %)**NOTE: User need to set Calculate Flag to proper value before use Flow Sensor. Downlink or AT Command see: **(%%)Refer: [[Set Calculate Flag>>||anchor="H3.3.6Setthecalculateflag"]]
++)))
--(% style="color:#4472c4" %)**0B05(H) = 2821 (D) = 2821 mm.**
++* (((
++(% style="color:#037691" %)**Alarm**
  )))
++(((
++See [[Alarm for continuously water flow>>||anchor="H3.3.4Alarmforcontinuouslywaterflow"]]
++)))
--* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
--* If the sensor value lower than 0x0118 (280mm), the sensor value will be invalid. Since v1.1.4, all value lower than 280mm will be set to 0x0014(20mm) which means the value is invalid.
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-4.png?width=724&height=65&rev=1.1||alt="image-20220519095946-4.png"]]
--=== 2.3.3  Interrupt Pin ===
++* (((
++(% style="color:#037691" %)**Total pulse**
++)))
--This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3A0SetInterruptMode"]] for the hardware and software set up.
++(((
++Total pulse/counting since factory
++)))
--**Example:**
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
++)))
--0x00: Normal uplink packet.
++* (((
++(% style="color:#037691" %)**Last Pulse**
++)))
--0x01: Interrupt Uplink Packet.
++(((
++Total pulse since last FPORT=2 uplink. (Default 20 minutes)
++)))
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
++)))
--=== 2.3.4  DS18B20 Temperature sensor ===
++* (((
++(% style="color:#037691" %)**MOD: Default =0**
++)))
++(((
++MOD=0 ~-~-> Uplink Total Pulse since factory
++)))
--This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
++(((
++MOD=1 ~-~-> Uplink total pulse since last FPORT=2 uplink.
++)))
--**Example**:
++* (((
++(% style="color:#037691" %)**Water Flow Value**
++)))
--If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
++(((
++**Total Water Flow Volume = (Calculate Flag) x (Total Pulse)=9597/450=21.3L**
++)))
--If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-5.png?width=727&height=50&rev=1.1||alt="image-20220519095946-5.png"]]
--(% style="color:red" %)**Note: DS18B20 feature is supported in the hardware version > v1.3 which made since early of 2021.**
++(((
++**Total Water Flow for TDC timer = (Calculate Flag) x (Last Pulse)=79/450=0.2L**
++)))
--=== 2.3.5  Sensor Flag ===
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-6.png?width=733&height=43&rev=1.1||alt="image-20220519095946-6.png"]] **       **
++=== 2.3.4 Historical Water Flow Status, FPORT~=3 ===
++
++
  (((
--0x01: Detect Ultrasonic Sensor
++SW3L-LB stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5DatalogFeature"]].
  )))
  (((
--0x00: No Ultrasonic Sensor
++The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time water flow status.
  )))
++* (((
++Each data entry is 11 bytes and has the same structure as [[real time water flow status>>||anchor="H2.3.3A0WaterFlowValue2CUplinkFPORT3D2"]], to save airtime and battery, SW3L will send max bytes according to the current DR and Frequency bands.
++)))
--=== 2.3.6  Decode payload in The Things Network ===
++(((
++For example, in the US915 band, the max payload for different DR is:
++)))
++(((
++(% style="color:blue" %)**a) DR0:**(%%) max is 11 bytes so one entry of data
++)))
--While using TTN network, you can add the payload format to decode the payload.
++(((
++(% style="color:blue" %)**b) DR1:**(%%) max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850829385-439.png?rev=1.1||alt="1654850829385-439.png"]]
++(((
++(% style="color:blue" %)**c) DR2:**(%%) total payload includes 11 entries of data
++)))
--The payload decoder function for TTN V3 is here:
++(((
++(% style="color:blue" %)**d) DR3:**(%%) total payload includes 22 entries of data.
++)))
  (((
--DDS75-LB TTN V3 Payload Decoder:  [[ttps:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
++If SW3L-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0
  )))
++(((
++(% style="color:#037691" %)**Downlink:**
++)))
--== 2.4  Uplink Interval ==
++(((
++0x31 62 46 B1 F0 62 46 B3 94 07
++)))
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652926690850-712.png?width=726&height=115&rev=1.1||alt="1652926690850-712.png"]]
--The DDS75-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
--
--== 2.5  Show Data in DataCake IoT Server ==
--
--
  (((
--[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
++(% style="color:#037691" %)**Uplink:**
  )))
  (((
--
++00 00 01 00 00 00 00 62 46 B2 26 00 00 01 00 00 00 00 62 46 B2 5D 00 00 01 00 00 00 00 62 46 B2 99 00 00 01 00 00 00 00 62 46 B2 D5 00 00 01 00 00 01 15 62 46 B3 11 00 00 01 00 00 01 1F 62 46 B3 7E
  )))
  (((
--(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
++(% style="color:#037691" %)**Parsed Value:**
  )))
  (((
--(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
++[Alarm, Calculate Flag, MOD, Total pulse or Last Pulse,** **Water Flow Value, TIME]
  )))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592790040-760.png?rev=1.1||alt="1654592790040-760.png"]]
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:04:54],
++)))
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:05:49],
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592800389-571.png?rev=1.1||alt="1654592800389-571.png"]]
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:06:49],
++)))
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:07:49],
++)))
--(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
++(((
++[FALSE,0,0,277,0.6,2022-04-01 08:08:49],
++)))
--(% style="color:blue" %)**Step 4**(%%)**: Search the DDS75-LB and add DevEUI.**
++(((
++[FALSE,0,0,287,0.6,2022-04-01 08:10:38],
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652926777796-267.png?width=724&height=279&rev=1.1||alt="1652926777796-267.png"]]
--After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake.
++== 2.4 Payload Decoder file ==
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
++In TTN, use can add a custom payload so it shows friendly reading
++In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
--== 2.6 Datalog Feature ==
++== 2.5 Datalog Feature ==
--Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DDS75-LB will store the reading for future retrieving purposes.
++Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, SW3L-LB will store the reading for future retrieving purposes.
--=== 2.6.1 Ways to get datalog via LoRaWAN ===
++=== 2.5.1 Ways to get datalog via LoRaWAN ===
--Set PNACKMD=1, DDS75-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DDS75-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
++Set PNACKMD=1, SW3L-LB will wait for ACK for every uplink, when there is no LoRaWAN network,SW3L-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
++
  * (((
--a) DDS75-LB will do an ACK check for data records sending to make sure every data arrive server.
++a) SW3L-LB will do an ACK check for data records sending to make sure every data arrive server.
  )))
  * (((
--b) DDS75-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but DDS75-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DDS75-LB gets a ACK, DDS75-LB will consider there is a network connection and resend all NONE-ACK messages.
++b) SW3L-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but SW3L-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if SW3L-LB gets a ACK, SW3L-LB will consider there is a network connection and resend all NONE-ACK messages.
  )))
  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
@@ -443,10 +443,10 @@
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
--=== 2.6.2 Unix TimeStamp ===
++=== 2.5.2 Unix TimeStamp ===
--DDS75-LB uses Unix TimeStamp format based on
++SW3L-LB uses Unix TimeStamp format based on
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
@@ -460,17 +460,17 @@
  So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
--=== 2.6.3 Set Device Time ===
++=== 2.5.3 Set Device Time ===
  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
--Once DDS75-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SW3L-LB. If DDS75-LB fails to get the time from the server, DDS75-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
++Once SW3L-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SW3L-LB. If SW3L-LB fails to get the time from the server, SW3L-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
--=== 2.6.4 Poll sensor value ===
++=== 2.5.4 Poll sensor value ===
  Users can poll sensor values based on timestamps. Below is the downlink command.
@@ -493,14 +493,14 @@
  )))
  (((
--Uplink Internal =5s，means DDS75-LB will send one packet every 5s. range 5~~255s.
++Uplink Internal =5s，means SW3L-LB will send one packet every 5s. range 5~~255s.
  )))
--== 2.7 Frequency Plans ==
++== 2.6 Frequency Plans ==
--The DDS75-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
++The SW3L-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
@@ -510,7 +510,7 @@
  == 3.1 Configure Methods ==
--DDS75-LB supports below configure method:
++SW3L-LB supports below configure method:
  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
@@ -518,6 +518,7 @@
  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
++
  == 3.2 General Commands ==
@@ -532,10 +532,10 @@
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--== 3.3 Commands special design for DDS75-LB ==
++== 3.3 Commands special design for SW3L-LB ==
--These commands only valid for DDS75-LB, as below:
++These commands only valid for SW3L-LB, as below:
  === 3.3.1 Set Transmit Interval Time ===
@@ -581,9 +581,168 @@
  )))
--=== 3.3.2 Set Interrupt Mode ===
++=== 3.3.2 Quit AT Command ===
++Feature: Quit AT Command mode, so user needs to input the password again before using AT Commands.
++
++(% style="color:blue" %)**AT Command: AT+DISAT**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:452px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 198px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 99px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:155px" %)AT+DISAT|(% style="width:198px" %)Quit AT Commands mode|(% style="width:96px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++No downlink command for this feature.
++
++
++=== 3.3.3 Get Device Status ===
++
++
++Send a LoRaWAN downlink to ask device send Alarm settings.
++
++(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
++
++Sensor will upload Device Status via FPORT=5. See payload section for detail.
++
++
++=== 3.3.4 Alarm for continuously water flow ===
++
++
++(((
++This feature is to monitor and send Alarm for continuously water flow.
++)))
++
++(((
++Example case is for Toilet water monitoring, if some one push toilet button, the toilet will have water flow. If the toilet button has broken and can't returned to original state, the water flow will keep for hours or days which cause huge waste for water.
++)))
++
++(((
++To monitor this faulty and send alarm, there are two settings:
++)))
++
++* (((
++(% style="color:#4f81bd" %)**Stop Duration: Unit: Second**
++)))
++
++(((
++Default: 15s, If SW3L-LB didn't see any water flow in 15s, SW3L-LB will consider stop of water flow event.
++)))
++
++* (((
++(% style="color:#4f81bd" %)**Alarm Timer: Units: Minute; Default 0 minutes (means Alarm disable)**
++)))
++
++(((
++**Example:** 3 minutes, if SW3L-LB detect a start of water flow event and didn't detect a stop event within Alarm timer, SW3L-LB will send an Alarm to indicate a water flow abnormal alarm.
++)))
++
++(((
++So for example, If we set stop duration=15s and Alarm Timer=3minutes. If the toilet water flow continuously for more than 3 minutes, Sensor will send an alarm (in Confirmed MODE) to platform.
++)))
++
++(((
++(% style="color:red" %)**Note:** **After this alarm is send, sensor will consider a stop of water flow and count for another new event. So if water flow waste last for 1 hour, Sensor will keep sending alarm every 3 minutes.**
++)))
++
++(((
++(% style="color:#4f81bd" %)**AT Command**(%%) to configure:
++)))
++
++* (((
++AT+PTRIG=15,3   ~-~-> Set Stop duration: 15s, Alarm Timer: 3 minutes.
++)))
++
++* (((
++AT+ PTRIG=15,0  ~-~-> Default Value, disable water waste Alarm.
++)))
++
++(((
++(% style="color:#4f81bd" %)**Downlink Command**(%%) to configure:
++)))
++
++(((
++Command: **0xAA aa bb cc**
++)))
++
++(((
++AA: Command Type Code
++)))
++
++(((
++aa: Stop duration
++)))
++
++(((
++bb cc: Alarm Timer
++)))
++
++(((
++If user send 0xAA 0F 00 03: equal to AT+PTRIG=15,3
++)))
++
++
++=== 3.3.5 Clear Flash Record ===
++
++
++Feature: Clear flash storage for data log feature.
++
++(% style="color:blue" %)**AT Command: AT+CLRDTA**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
++|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 169px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 174px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:157px" %)AT+CLRDTA|(% style="width:169px" %)Clear flash storage for data log feature.|Clear all stored sensor data… OK
++
++(((
++(% style="color:blue" %)**Downlink Command:**
++)))
++
++(((
++* **Example**: 0xA301     ~/~/  Same as AT+CLRDTA
++)))
++
++
++
++=== 3.3.6 Set the calculate flag ===
++
++
++Feature: Set the calculate flag
++
++(% style="color:blue" %)**AT Command: AT+CALCFLAG**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:461px" %)
++|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:158px" %)AT+CALCFLAG =1|(% style="width:192px" %)Set the calculate flag to 1.|(% style="width:109px" %)OK
++|(% style="width:158px" %)AT+CALCFLAG =2|(% style="width:192px" %)Set the calculate flag to 2.|(% style="width:109px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example**: 0XA501         ~/~/  Same as AT+CALCFLAG =1
++
++
++=== 3.3.7 Set count number ===
++
++
++Feature: Manually set the count number
++
++(% style="color:blue" %)**AT Command: AT+SETCNT**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:479px" %)
++|=(% style="width: 160px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 223px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 96px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:160px" %)AT+ SETCNT =0|(% style="width:221px" %)Set the count number to 0.|(% style="width:95px" %)OK
++|(% style="width:160px" %)AT+ SETCNT =100|(% style="width:221px" %)Set the count number to 100.|(% style="width:95px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example**: 0xA6000001      ~/~/  Same as AT+ SETCNT =1
++
++* **Example**: 0xA6000064      ~/~/  Same as AT+ SETCNT =100
++
++
++=== 3.3.8 Set Interrupt Mode ===
++
++
  Feature, Set Interrupt mode for PA8 of pin.
  When AT+INTMOD=0 is set, PA8 is used as a digital input port.
@@ -616,10 +616,30 @@
  * Example 2: Downlink Payload: 06000003      ~/~/   Set the interrupt mode to rising edge trigger
++=== 3.3.9 Set work mode ===
++
++
++Feature: Manually set the work mode
++
++
++(% style="color:blue" %)**AT Command: AT+MOD**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:463px" %)
++|=(% style="width: 162px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 108px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:162px" %)AT+MOD=0|(% style="width:191px" %)Set the work mode to 0.|(% style="width:106px" %)OK
++|(% style="width:162px" %)AT+MOD=1|(% style="width:191px" %)Set the work mode to 1|(% style="width:106px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example: **0x0A00       ~/~/  Same as AT+MOD=0
++
++* **Example:** 0x0A01       ~/~/  Same as AT+MOD=1
++
++
  = 4. Battery & Power Consumption =
--DDS75-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++SW3L-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
@@ -628,7 +628,7 @@
  (% class="wikigeneratedid" %)
--User can change firmware DDS75-LB to:
++User can change firmware SW3L-LB to:
  * Change Frequency band/ region.
@@ -644,6 +644,7 @@
  * Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
++
  = 6. FAQ =
  == 6.1  AT Commands input doesn't work ==
@@ -723,6 +723,7 @@
  * Weight / pcs : g
++
  = 9. Support =