Skip to Content
Last modified by Mengting Qiu on 2023/12/14 11:15
From version 67.2
edited by Xiaoling
on 2023/05/30 14:01
Change comment: There is no comment for this version
To version 82.4
edited by Xiaoling
on 2023/06/14 16:46
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SW3L-LB -- LoRaWAN Flow Sensor User Manual
1 +LDS12-LB -- LoRaWAN LiDAR ToF Distance Sensor User Manual
Content
... ... @@ -1,10 +1,12 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20230530140053-1.jpeg||height="645" width="645"]]
2 +[[image:image-20230614153353-1.png]]
3 3  
4 4  
5 5  
6 6  
7 7  
8 +
9 +
8 8  **Table of Contents：**
9 9  
10 10  {{toc/}}
... ... @@ -16,29 +16,26 @@
16 16  
17 17  = 1. Introduction =
18 18  
19 -== 1.1 What is CPL03-LB LoRaWAN Pulse/Contact Sensor ==
21 +== 1.1 What is LoRaWAN LiDAR ToF Distance Sensor ==
20 20  
21 21  
22 -The Dragino CPL03-LB is a (% style="color:blue" %)**LoRaWAN Contact Sensor**(%%) for Internet of Things solution. It detects dry contact status, open time, open counts, and then upload to IoT server via LoRaWAN wireless protocol.
24 +The Dragino LDS12-LB is a (% style="color:blue" %)**LoRaWAN LiDAR ToF (Time of Flight) Distance Sensor**(%%) for Internet of Things solution. It is capable to measure the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)!. The LiDAR probe uses laser induction technology for distance measurement.
23 23  
24 -The CPL03-LB will send periodically data every day as well as for each dry contact action. It also counts the contact open times and calculate last open duration. User can also disable the uplink for each open/close event, instead, device can count each open event and uplink periodically.
26 +The LDS12-LB can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.
25 25  
26 -The LoRa wireless technology used in CPL03-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
28 +It detects the distance between the measured object and the sensor, and uploads the value via wireless to LoRaWAN IoT Server.
27 27  
28 -CPL03-LB (% style="color:blue" %)**supports open alarm feature**(%%), user can set open alarm for instant notice. CPL03-LB (% style="color:blue" %)**supports Datalog feature**(%%), it can save the data when there is no LoRaWAN network and uplink when network recover.
30 +The LoRa wireless technology used in LDS12-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
29 29  
30 -CPL03-LB is designed for outdoor use. It has a weatherproof enclosure and industrial level battery to work in low to high temperatures.
32 +LDS12-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
31 31  
32 -CPL03-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
34 +LDS12-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
33 33  
34 -CPL03-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
36 +Each LDS12-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
35 35  
36 -Each CPL03-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
38 +[[image:image-20230614162334-2.png||height="468" width="800"]]
37 37  
38 38  
39 -[[image:image-20230530135919-1.png||height="404" width="806"]]
40 -
41 -
42 42  == 1.2 ​Features ==
43 43  
44 44  
... ... @@ -45,14 +45,13 @@
45 45  * LoRaWAN 1.0.3 Class A
46 46  * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
47 47  * Ultra-low power consumption
48 -* Open/Close detect
49 -* Open/Close statistics
50 -* Temperature & Humidity alarm
51 -* supports open alarm feature
52 -* supports Datalog feature
47 +* Laser technology for distance detection
48 +* Measure Distance: 0.1m~~12m @ 90% Reflectivity
49 +* Accuracy :  ±5cm@(0.1-6m), ±1%@(6m-12m)
50 +* Monitor Battery Level
53 53  * Support Bluetooth v5.1 and LoRaWAN remote configure
54 54  * Support wireless OTA update firmware
55 -* Uplink on periodically and open/close event
53 +* AT Commands to change parameters
56 56  * Downlink to change configure
57 57  * 8500mAh Battery for long term use
58 58  
... ... @@ -64,6 +64,23 @@
64 64  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
65 65  * Operating Temperature: -40 ~~ 85°C
66 66  
65 +(% style="color:#037691" %)**Probe Specification:**
66 +
67 +* Storage temperature：-20℃~~75℃
68 +* Operating temperature : -20℃~~60℃
69 +* Measure Distance:
70 +** 0.1m ~~ 12m @ 90% Reflectivity
71 +** 0.1m ~~ 4m @ 10% Reflectivity
72 +* Accuracy : ±5cm@(0.1-6m), ±1%@(6m-12m)
73 +* Distance resolution : 5mm
74 +* Ambient light immunity : 70klux
75 +* Enclosure rating : IP65
76 +* Light source : LED
77 +* Central wavelength : 850nm
78 +* FOV : 3.6°
79 +* Material of enclosure : ABS+PC
80 +* Wire length : 25cm
81 +
67 67  (% style="color:#037691" %)**LoRa Spec:**
68 68  
69 69  * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
... ... @@ -84,13 +84,23 @@
84 84  * Sleep Mode: 5uA @ 3.3v
85 85  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
86 86  
102 +
103 +
87 87  == 1.4 Applications ==
88 88  
89 89  
90 -* Open/Close Detection
91 -* Pulse meter application
92 -* Dry Contact Detection
107 +* Horizontal distance measurement
108 +* Parking management system
109 +* Object proximity and presence detection
110 +* Intelligent trash can management system
111 +* Robot obstacle avoidance
112 +* Automatic control
113 +* Sewer
93 93  
115 +
116 +
117 +(% style="display:none" %)
118 +
94 94  == 1.5 Sleep mode and working mode ==
95 95  
96 96  
... ... @@ -121,9 +121,8 @@
121 121  == 1.7 BLE connection ==
122 122  
123 123  
124 -CPL03-LB support BLE remote configure.
149 +LDS12-LB support BLE remote configure.
125 125  
126 -
127 127  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
128 128  
129 129  * Press button to send an uplink
... ... @@ -135,9 +135,10 @@
135 135  
136 136  == 1.8 Pin Definitions ==
137 137  
138 -[[image:image-20230523174230-1.png]]
162 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/WL03A-LB_LoRaWAN_None-Position_Rope_Type_Water_Leak_Controller_User_Manual/WebHome/image-20230613144156-1.png?rev=1.1||alt="image-20230613144156-1.png"]]
139 139  
140 140  
165 +
141 141  == 1.9 Mechanical ==
142 142  
143 143  
... ... @@ -150,12 +150,19 @@
150 150  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
151 151  
152 152  
153 -= 2. Configure CPL03-LB to connect to LoRaWAN network =
178 +(% style="color:blue" %)**Probe Mechanical:**
154 154  
180 +
181 +
182 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLDS12-LoRaWAN%20LiDAR%20ToF%20Distance%20Sensor%20User%20Manual/WebHome/1654827224480-952.png?rev=1.1||alt="1654827224480-952.png"]]
183 +
184 +
185 += 2. Configure LDS12-LB to connect to LoRaWAN network =
186 +
155 155  == 2.1 How it works ==
156 156  
157 157  
158 -The CPL03-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the CPL03-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
190 +The LDS12-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the LDS12-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
159 159  
160 160  (% style="display:none" %) (%%)
161 161  
... ... @@ -166,12 +166,12 @@
166 166  
167 167  The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
168 168  
169 -[[image:image-20230530135929-2.png||height="404" width="806"]](% style="display:none" %)
201 +[[image:image-20230614162359-3.png||height="468" width="800"]](% style="display:none" %)
170 170  
171 171  
172 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from CPL03-LB.
204 +(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from LDS12-LB.
173 173  
174 -Each CPL03-LB is shipped with a sticker with the default device EUI as below:
206 +Each LDS12-LB is shipped with a sticker with the default device EUI as below:
175 175  
176 176  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
177 177  
... ... @@ -200,10 +200,10 @@
200 200  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
201 201  
202 202  
203 -(% style="color:blue" %)**Step 2:**(%%) Activate on CPL03-LB
235 +(% style="color:blue" %)**Step 2:**(%%) Activate on LDS12-LB
204 204  
205 205  
206 -Press the button for 5 seconds to activate the CPL03-LB.
238 +Press the button for 5 seconds to activate the LDS12-LB.
207 207  
208 208  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
209 209  
... ... @@ -210,555 +210,366 @@
210 210  After join success, it will start to upload messages to TTN and you can see the messages in the panel.
211 211  
212 212  
213 -== 2.3 ​Uplink Payload ==
245 +== 2.3  ​Uplink Payload ==
214 214  
215 -=== 2.3.1 Device Status, FPORT~=5 ===
216 216  
248 +(((
249 +LDS12-LB will uplink payload via LoRaWAN with below payload format: 
250 +)))
217 217  
218 -Users can use the downlink command(**0x26 01**) to ask CPL03-LB to send device configure detail, include device configure status. CPL03-LB will uplink a payload via FPort=5 to server.
252 +(((
253 +Uplink payload includes in total 11 bytes.
254 +)))
219 219  
220 -The Payload format is as below.
221 221  
257 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
258 +|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
259 +**Size(bytes)**
260 +)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#d9e2f3; color:#0070c0" %)**2**|=(% style="background-color:#d9e2f3; color:#0070c0" %)**2**|=(% style="background-color:#d9e2f3; color:#0070c0" %)**1**|=(% style="background-color:#d9e2f3; color:#0070c0" %)**1**|=(% style="background-color:#d9e2f3; color:#0070c0" %)**1**
261 +|(% style="width:62.5px" %)**Value**|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(% style="width:62.5px" %)(((
262 +[[Temperature DS18B20>>||anchor="H2.3.2A0DS18B20Temperaturesensor"]]
263 +)))|[[Distance>>||anchor="H2.3.3A0Distance"]]|[[Distance signal strength>>||anchor="H2.3.4A0Distancesignalstrength"]]|(((
264 +[[Interrupt flag>>||anchor="H2.3.5A0InterruptPin"]]
265 +)))|[[LiDAR temp>>||anchor="H2.3.6A0LiDARtemp"]]|(((
266 +[[Message Type>>||anchor="H2.3.7A0MessageType"]]
267 +)))
222 222  
223 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
224 -|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
225 -|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
226 -|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
269 +[[image:1654833689380-972.png]]
227 227  
228 -Example parse in TTNv3
229 229  
230 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652859749264-179.png?width=723&height=275&rev=1.1||alt="1652859749264-179.png"]]
272 +=== 2.3.1  Battery Info ===
231 231  
232 232  
233 -(% style="color:#037691" %)**Sensor Model**(%%): For CPL03-LB, this value is 0x0A
275 +Check the battery voltage for LDS12-LB.
234 234  
235 -(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
277 +Ex1: 0x0B45 = 2885mV
236 236  
237 -(% style="color:#037691" %)**Frequency Band**:
279 +Ex2: 0x0B49 = 2889mV
238 238  
239 -*0x01: EU868
240 240  
241 -*0x02: US915
282 +=== 2.3.2  DS18B20 Temperature sensor ===
242 242  
243 -*0x03: IN865
244 244  
245 -*0x04: AU915
285 +This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
246 246  
247 -*0x05: KZ865
248 248  
249 -*0x06: RU864
288 +**Example**:
250 250  
251 -*0x07: AS923
290 +If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
252 252  
253 -*0x08: AS923-1
292 +If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
254 254  
255 -*0x09: AS923-2
256 256  
257 -*0x0a: AS923-3
295 +=== 2.3.3  Distance ===
258 258  
259 -*0x0b: CN470
260 260  
261 -*0x0c: EU433
298 +Represents the distance value of the measurement output, the default unit is cm, and the value range parsed as a decimal number is 0-1200. In actual use, when the signal strength value Strength.
262 262  
263 -*0x0d: KR920
264 264  
265 -*0x0e: MA869
301 +**Example**:
266 266  
303 +If the data you get from the register is 0x0B 0xEA, the distance between the sensor and the measured object is 0BEA(H) = 3050 (D)/10 = 305cm.
267 267  
268 -(% style="color:#037691" %)**Sub-Band**:
269 269  
270 -AU915 and US915:value 0x00 ~~ 0x08
306 +=== 2.3.4  Distance signal strength ===
271 271  
272 -CN470: value 0x0B ~~ 0x0C
273 273  
274 -Other Bands: Always 0x00
309 +Refers to the signal strength, the default output value will be between 0-65535. When the distance measurement gear is fixed, the farther the distance measurement is, the lower the signal strength; the lower the target reflectivity, the lower the signal strength. When Strength is greater than 100 and not equal to 65535, the measured value of Dist is considered credible.
275 275  
276 276  
277 -(% style="color:#037691" %)**Battery Info**:
312 +**Example**:
278 278  
279 -Check the battery voltage.
314 +If payload is: 01D7(H)=471(D), distance signal strength=471, 471>100,471≠65535, the measured value of Dist is considered credible.
280 280  
281 -Ex1: 0x0B45 = 2885mV
316 +Customers can judge whether they need to adjust the environment based on the signal strength.
282 282  
283 -Ex2: 0x0B49 = 2889mV
284 284  
319 +=== 2.3.5  Interrupt Pin ===
285 285  
286 -=== 2.3.2 Sensor Configuration, FPORT~=4 ===
287 287  
322 +This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H4.2A0SetInterruptMode"]] for the hardware and software set up.
288 288  
289 -CPL03-LB will only send this command after getting the downlink command (0x26 02) from the server.
324 +Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>||anchor="H1.6A0Pinmappingandpoweron"]].
290 290  
291 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
292 -|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0; width:504px" %)**Sensor Configuration FPORT=4**
293 -|**Size(bytes)**|(% style="width:75px" %)**3**|(% style="width:77px" %)**1**|(% style="width:96px" %)**1**|(% style="width:158px" %)**2**|(% style="width:158px" %)**1**
294 -|**Value**|(% style="width:75px" %)TDC (unit:sec)|(% style="width:77px" %)Disalarm|(% style="width:96px" %)Keep status|(% style="width:158px" %)Keep time (unit: sec)|(% style="width:158px" %)Trigger mode
326 +**Example:**
295 295  
296 -* (((
297 -(% style="color:#037691" %)** TDC: (default: 0x001C20)**
298 -)))
328 +0x00: Normal uplink packet.
299 299  
300 -(((
301 -Uplink interval for the total pulse count, default value is 0x001C20 which is 7200 seconds = 2 hours.
330 +0x01: Interrupt Uplink Packet.
302 302  
303 -
304 -)))
305 305  
306 -* (((
307 -(% style="color:#037691" %)** Disalarm: (default: 0)**
308 -)))
333 +=== 2.3.6  LiDAR temp ===
309 309  
310 -(((
311 -(% style="color:blue" %)** If Disalarm = 1**(%%), CPL03-LB will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many disconnect/connect event, and platform only care about the total number of pulse.
312 -)))
313 313  
314 -(((
315 -(% style="color:blue" %)** If Disalarm = 0**(%%), CPL03-LB will send uplink at every TDC periodically.
336 +Characterize the internal temperature value of the sensor.
316 316  
317 -
318 -)))
338 +**Example: **
339 +If payload is: 1C(H) <<24>>24=28(D),LiDAR temp=28℃.
340 +If payload is: F2(H) <<24>>24=-14(D),LiDAR temp=-14℃.
319 319  
320 -* (((
321 -(% style="color:#037691" %)** Keep Status & Keep Time**
322 -)))
323 323  
324 -(((
325 -Shows the configure value of [[Alarm Base on Timeout Feature>>||anchor="H3.3.5AlarmBaseonTimeout"]]
343 +=== 2.3.7  Message Type ===
326 326  
327 -
328 -)))
329 329  
330 -* (((
331 -(% style="color:#037691" %)** Trigger mode (default: 0)**
332 -)))
333 -
334 334  (((
335 -(% style="color:blue" %)** If Trigger mode = 0**(%%), count close to open event.
347 +For a normal uplink payload, the message type is always 0x01.
336 336  )))
337 337  
338 338  (((
339 -(% style="color:blue" %)** If Trigger mode = 1**(%%), count open to close event.
351 +Valid Message Type:
340 340  )))
341 341  
342 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652860064987-743.png?width=730&height=152&rev=1.1||alt="1652860064987-743.png"]]
354 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:499px" %)
355 +|=(% style="width: 161px;background-color:#D9E2F3;color:#0070C0" %)**Message Type Code**|=(% style="width: 164px;background-color:#D9E2F3;color:#0070C0" %)**Description**|=(% style="width: 174px;background-color:#D9E2F3;color:#0070C0" %)**Payload**
356 +|(% style="width:160px" %)0x01|(% style="width:163px" %)Normal Uplink|(% style="width:173px" %)[[Normal Uplink Payload>>||anchor="H2.3A0200BUplinkPayload"]]
357 +|(% style="width:160px" %)0x02|(% style="width:163px" %)Reply configures info|(% style="width:173px" %)[[Configure Info Payload>>||anchor="H4.3A0GetFirmwareVersionInfo"]]
343 343  
344 344  
345 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652860079526-831.png?width=729&height=209&rev=1.1||alt="1652860079526-831.png"]]
360 +=== 2.3.8  Decode payload in The Things Network ===
346 346  
347 347  
348 -=== 2.3.3 Real-Time Open/Close Status, Uplink FPORT~=2 ===
363 +While using TTN network, you can add the payload format to decode the payload.
349 349  
350 350  
351 -(((
352 -(((
353 -CPL03-LB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And CPL03-LB will:
354 -)))
355 -)))
366 +[[image:1654592762713-715.png]]
356 356  
368 +
357 357  (((
358 -(((
359 -periodically send this uplink every 2 hours, this interval [[can be changed>>||anchor="H3.3.1SetTransmitIntervalTime"]].
370 +The payload decoder function for TTN is here:
360 360  )))
361 -)))
362 362  
363 363  (((
364 -(((
365 -Uplink Payload totals 11 bytes.
374 +LDS12-LB TTN Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
366 366  )))
367 -)))
368 368  
369 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
370 -|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0; width: 520px;" %)**Real-Time Open/Close Status, FPORT=2**
371 -|(% style="width:60px" %)**Size(bytes)**|(% style="width:65px" %)**1**|(% style="width:65px" %)**3**|(% style="width:240px" %)**3**|(% style="width:90px" %)**4**
372 -|(% style="width:101px" %)**Value**|(% style="width:133px" %)Status & [[Alarm>>||anchor="H3.3.5AlarmBaseonTimeout"]]|(% style="width:92px" %)Total pulse|(% style="width:247px" %)The last open duration (unit: min)|(% style="width:149px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
373 373  
374 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:504px" %)
375 -|=(% colspan="4" style="background-color:#D9E2F3;color:#0070C0; width: 502px;" %)**Status & Alarm field**
376 -|(% style="width:60px" %)**Size(bit)**|(% style="width:70px" %)**6**|(% style="width:228px" %)**1**|(% style="width:146px" %)**1**
377 -|(% style="width:76px" %)Value|(% style="width:80px" %)Calculate Flag|(% style="width:208px" %)Alarm: 0: No Alarm; 1: Alarm|(% style="width:136px" %)Contact Status: 0: Open, 1: Close
378 +== 2.4  Uplink Interval ==
378 378  
379 -* (((
380 -(% style="color:#037691" %)** Calculate Flag**
381 -)))
382 382  
383 -(((
384 -The calculate flag is a user define field, IoT server can use this filed to handle different meter with different pulse factor. For example, if there are 100 water meters, meter 1 ~~50 are 1 liter/pulse and meter 51 ~~ 100 has 1.5 liter/pulse.
385 -)))
381 +The LDS12-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>||anchor="H3.3.1SetTransmitIntervalTime"]]
386 386  
387 -(((
388 -User can set calculate flag to 1 for meter 1~~50 and 2 for meter 51 ~~ 100, So IoT Server can use this field for calculation.
389 -)))
390 390  
391 -(((
392 -Default value: 0. 
393 -)))
384 +== 2.5  ​Show Data in DataCake IoT Server ==
394 394  
395 -(((
396 -Range (6 bits): (b)000000 ~~ (b) 111111
397 -)))
398 398  
399 399  (((
400 -Refer: [[Set Calculate Flag>>||anchor="H3.3.8Setthecalculateflag"]]
401 -
402 -
388 +[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
403 403  )))
404 404  
405 -* (((
406 -(% style="color:#037691" %)** Alarm**
407 -)))
408 408  
409 409  (((
410 -See [[Alarm Base on Timeout>>||anchor="H3.3.5AlarmBaseonTimeout"]]
411 -
412 -
393 +(% style="color:blue" %)**Step 1**(%%)**: Be sure that your device is programmed and properly connected to the network at this time.**
413 413  )))
414 414  
415 -* (((
416 -(% style="color:#037691" %)** Contact Status**
417 -)))
418 -
419 419  (((
420 -0: Open
397 +(% style="color:blue" %)**Step 2**(%%)**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:**
421 421  )))
422 422  
423 -(((
424 -1: Close
425 425  
426 -
427 -)))
401 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592790040-760.png?rev=1.1||alt="1654592790040-760.png"]]
428 428  
429 -* (((
430 -(% style="color:#037691" %)** Total pulse**
431 -)))
432 432  
433 -(((
434 -Total pulse/counting base on dry [[contact trigger event>>||anchor="H2.3.2SensorConfiguration2CFPORT3D4"]]
435 -)))
404 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654592800389-571.png?rev=1.1||alt="1654592800389-571.png"]]
436 436  
437 -(((
438 -Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
439 439  
440 -
441 -)))
407 +(% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
442 442  
443 -* (((
444 -(% style="color:#037691" %)** The last open duration**
445 -)))
409 +(% style="color:blue" %)**Step 4**(%%)**: Search the LDS12-LB and add DevEUI.**
446 446  
447 -(((
448 -Dry Contact last open duration.
449 -)))
411 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
450 450  
451 -(((
452 -Unit: min.
453 -)))
454 454  
455 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652860403792-491.png?width=735&height=153&rev=1.1||alt="1652860403792-491.png"]]
414 +After added, the sensor data arrive TTN V3, it will also arrive and show in Datacake.
456 456  
416 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
457 457  
458 -=== 2.3.4 Real-Time Open/Close Status, 3 pulse mode, Uplink FPORT~=6 ===
459 459  
419 +== 2.6 Datalog Feature ==
460 460  
461 -(% style="color:red" %)**Note:**
462 462  
463 -* Firmware support for this mode is not released. If users want to test, please contact Dragino support.
464 -* Users need to run (% style="color:blue" %)**AT+MOD=3**(%%) to support this model after updating the firmware.
465 -* This mode doesn't support Historical Events and Datalog features.
422 +Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, LDS12-LB will store the reading for future retrieving purposes.
466 466  
467 -(% style="color:blue" %)**CPL03-LB 3 Pulse Wiring:**
468 468  
469 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20221013153352-1.png?width=720&height=628&rev=1.1||alt="image-20221013153352-1.png"]]
425 +=== 2.6.1 Ways to get datalog via LoRaWAN ===
470 470  
471 471  
472 -(% style="color:blue" %)**Payload:**
428 +Set PNACKMD=1, LDS12-LB will wait for ACK for every uplink, when there is no LoRaWAN network,LDS12-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
473 473  
474 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20221013153352-2.png?width=1215&height=167&rev=1.1||alt="image-20221013153352-2.png"]]
475 -
476 -
477 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:447px" %)
478 -|(% style="background-color:#d9e2f3; color:#0070c0; width:95px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:61px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:98px" %)**3**|(% style="background-color:#d9e2f3; color:#0070c0; width:98px" %)**3**|(% style="background-color:#d9e2f3; color:#0070c0; width:95px" %)**3**
479 -|(% style="width:93px" %)Value|(% style="width:59px" %)Status|(% style="width:98px" %)(((
480 -Port1 Total Pulse(PB14)
481 -)))|(% style="width:96px" %)(((
482 -Port2 Total Pulse(PB15)
483 -)))|(% style="width:94px" %)(((
484 -Port3 Total Pulse(PA4)
430 +* (((
431 +a) LDS12-LB will do an ACK check for data records sending to make sure every data arrive server.
485 485  )))
433 +* (((
434 +b) LDS12-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but LDS12-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if LDS12-LB gets a ACK, LDS12-LB will consider there is a network connection and resend all NONE-ACK messages.
435 +)))
486 486  
487 -(% style="color:blue" %)**Status:**
437 +Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
488 488  
489 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:257px" %)
490 -|(% style="background-color:#d9e2f3; color:#0070c0; width:75px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:112px" %)**6**|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)**2**
491 -|(% style="width:75px" %)Value|(% style="width:111px" %)Calculate Flag|(% style="width:68px" %)Reserve
439 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
492 492  
493 -(% style="color:red" %)**Max COUNT for each port is 16777215. Exceed this number will reset to 1.**
494 494  
442 +=== 2.6.2 Unix TimeStamp ===
495 495  
496 -(% style="color:blue" %)**Related AT Command:**
497 497  
498 -(% style="color:#037691" %)**AT+TTRMOD1:  Port1 count mode;  0: Signal falling edge(Default), 1: Signal raising edge**
445 +LDS12-LB uses Unix TimeStamp format based on
499 499  
500 - AT+TTRMOD1=0  Downlink Command: 0xA4 01 00
447 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
501 501  
502 - AT+TTRMOD1=1  Downlink Command: 0xA4 01 01
449 +User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
503 503  
451 +Below is the converter example
504 504  
505 -(% style="color:#037691" %)**AT+TTRMOD2:  Port2 count mode;  0: Signal falling edge(Default), 1: Signal raising edge**
453 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
506 506  
507 - AT+TTRMOD1=0  Downlink Command: 0xA4 02 00
508 508  
509 - AT+TTRMOD1=1  Downlink Command: 0xA4 02 01
456 +So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
510 510  
511 511  
512 -(% style="color:#037691" %)**AT+TTRMOD3:  Port3 count mode;  0: Signal falling edge(Default), 1: Signal raising edge**
459 +=== 2.6.3 Set Device Time ===
513 513  
514 - AT+TTRMOD1=0  Downlink Command: 0xA4 03 00
515 515  
516 - AT+TTRMOD1=1  Downlink Command: 0xA4 03 01
462 +User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
517 517  
464 +Once LDS12-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to LDS12-LB. If LDS12-LB fails to get the time from the server, LDS12-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
518 518  
519 -(% style="color:#037691" %)**AT+CALCFLAG:  Calculate Flag ( Default : 0 )**
466 +(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
520 520  
521 - AT+CALCFLAG=aa
522 522  
469 +=== 2.6.4 Poll sensor value ===
523 523  
524 -(% style="color:blue" %)**Downlink Command: 0xA5 aa**
525 525  
526 -(% style="color:#037691" %)**AT+COUNTMOD:  Accumulative Mode;  0: Accumulative (Default),1: Reset after uplink.**
472 +Users can poll sensor values based on timestamps. Below is the downlink command.
527 527  
528 - AT+COUNTMOD=0 Downlink Command: 0x0B 00
474 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
475 +|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
476 +|(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
477 +|(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
529 529  
530 - AT+COUNTMOD=1 Downlink Command: 0x0B 01
531 -
532 -
533 -(% style="color:#037691" %)**AT+SETCNT:  Set count value**
534 -
535 - AT+SETCNT=1,aa  Downlink Command: 0xA6 01 aa aa aa
536 -
537 - AT+SETCNT=2,aa  Downlink Command: 0xA6 02 aa aa aa
538 -
539 - AT+SETCNT=3,aa  Downlink Command: 0xA6 03 aa aa aa
540 -
541 -
542 -(% style="color:blue" %)**Decode:  **(%%)[[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
543 -
544 -
545 -=== 2.3.5 Historical Door Open/Close Event, FPORT~=3 ===
546 -
547 -
548 548  (((
549 -CPL03-LB stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5DatalogFeature"]].
480 +Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
550 550  )))
551 551  
552 552  (((
553 -The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time open/close status.
484 +For example, downlink command [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20220518162852-1.png?rev=1.1||alt="image-20220518162852-1.png"]]
554 554  )))
555 555  
556 -* (((
557 -Each data entry is 11 bytes and has the same structure as [[Real-Time open/close status>>||anchor="H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]], to save airtime and battery, CPL03-LB will send max bytes according to the current DR and Frequency bands.
558 -)))
559 -
560 560  (((
561 -For example, in the US915 band, the max payload for different DR is:
488 +Is to check 2021/11/12 12:00:00 to 2021/11/12 15:00:00's data
562 562  )))
563 563  
564 564  (((
565 -a) (% style="color:blue" %)**DR0**(%%): max is 11 bytes so one entry of data
492 +Uplink Internal =5s，means LDS12-LB will send one packet every 5s. range 5~~255s.
566 566  )))
567 567  
568 -(((
569 -b) (% style="color:blue" %)**DR1**(%%): max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
570 -)))
571 571  
572 -(((
573 -c) (% style="color:blue" %)**DR2**(%%): total payload includes 11 entries of data
574 -)))
496 +== 2.7 Frequency Plans ==
575 575  
576 -(((
577 -d) (% style="color:blue" %)**DR3**(%%): total payload includes 22 entries of data.
578 -)))
579 579  
580 -(((
581 -If CPL03-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0
499 +The LDS12-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
582 582  
583 -
584 -)))
501 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
585 585  
586 -(% style="color:blue" %)** Downlink:**
587 587  
588 -(% class="box" %)
589 -(((
590 -**0x31 61 E9 3A D4 61 E9 3D E0 05**
591 -)))
504 +== 2.8 LiDAR ToF Measurement ==
592 592  
593 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652861353248-624.png?width=720&height=189&rev=1.1||alt="1652861353248-624.png"]]
506 +=== 2.8.1 Principle of Distance Measurement ===
594 594  
595 595  
596 -(% style="color:blue" %)** Uplink:**
509 +The LiDAR probe is based on TOF, namely, Time of Flight principle. To be specific, the product emits modulation wave of near infrared ray on a periodic basis, which will be reflected after contacting object. The product obtains the time of flight by measuring round-trip phase difference and then calculates relative range between the product and the detection object, as shown below.
597 597  
598 -(% class="box" %)
599 -(((
600 -**0E 00 23 E6 00 00 00 61 E9 3B 04 0E 00 23 E6 00 00 00 61 E9 3B 25 0D 00 00 00 00 00 00 61 E9 3B C8 0E 00 00 02 00 00 00 61 E9 3B D4 0E 00 00 06 00 00 00 61 E9 3B DB 01 00 00 00 00 00 00 61 E9 3C 91 01 00 00 00 00 00 00 61 E9 3C A1 0D 00 00 00 00 00 00 61 E9 3C BC 0E 00 00 07 00 00 00 61 E9 3C D6 00 00 00 00 00 00 00 61 E9 3D A6**
601 -)))
602 602  
603 -(% style="color:#037691" %)** **
512 +[[image:1654831757579-263.png]]
604 604  
605 -(% style="color:#037691" %)**Parsed Value:**
606 606  
607 -(((
608 -[ALARM, PIN_STATUS, TOTAL_PULSE, CALCULATE_FLAG, LAST_OPEN_DURATION, TIME]
609 -)))
515 +=== 2.8.2 Distance Measurement Characteristics ===
610 610  
611 -(((
612 -
613 -)))
614 614  
615 -(((
616 -[TRUE, CLOSE, 9190, 3, 0, 2022-01-20 10:35:48],
617 -)))
518 +With optimization of light path and algorithm, The LiDAR probe has minimized influence from external environment on distance measurement performance. Despite that, the range of distance measurement may still be affected by the environment illumination intensity and the reflectivity of detection object. As shown in below:
618 618  
619 -(((
620 -[TRUE, CLOSE, 9190, 3, 0, 2022-01-20 10:36:21],
621 -)))
520 +[[image:1654831774373-275.png]]
622 622  
623 -(((
624 -[FALSE, OPEN, 0, 3, 0, 2022-01-20 10:39:04],
625 -)))
626 626  
627 627  (((
628 -[TRUE, CLOSE, 2, 3, 0, 2022-01-20 10:39:16],
524 +(% style="color:blue" %)**① **(%%)Represents the detection blind zone of The LiDAR probe, 0-10cm, within which the output data is unreliable.
629 629  )))
630 630  
631 631  (((
632 -[TRUE, CLOSE, 6, 3, 0, 2022-01-20 10:39:23],
528 +(% style="color:blue" %)**② **(%%)Represents the operating range of The LiDAR probe detecting black target with 10% reflectivity, 0.1-5m.
633 633  )))
634 634  
635 635  (((
636 -[FALSE, OPEN, 0, 0, 0, 2022-01-20 10:42:25],
532 +(% style="color:blue" %)**③ **(%%)Represents the operating range of The LiDAR probe detecting white target with 90% reflectivity, 0.1-12m.
637 637  )))
638 638  
639 -(((
640 -[FALSE, OPEN, 0, 0, 0, 2022-01-20 10:42:41],
641 -)))
642 642  
643 643  (((
644 -[FALSE, OPEN, 0, 3, 0, 2022-01-20 10:43:08],
537 +Vertical Coordinates: Represents the radius of light spot for The LiDAR probe at different distances. The diameter of light spot depends on the FOV of The LiDAR probe (the term of FOV generally refers to the smaller value between the receiving angle and the transmitting angle), which is calculated as follows:
645 645  )))
646 646  
647 -(((
648 -[TRUE, CLOSE, 7, 3, 0, 2022-01-20 10:43:34],
649 -)))
650 650  
651 -(((
652 -[FALSE, CLOSE, 0, 0, 0, 2022-01-20 10:47:02],
541 +[[image:1654831797521-720.png]]
653 653  
654 -
655 -)))
656 656  
657 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652861480446-216.png?rev=1.1||alt="1652861480446-216.png"]]
658 -
659 -
660 -== 2.4 Payload Decoder file ==
661 -
662 -
663 -In TTN, use can add a custom payload so it shows friendly reading
664 -
665 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
666 -
667 -
668 -== 2.5 Datalog Feature ==
669 -
670 -
671 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, CPL03-LB will store the reading for future retrieving purposes.
672 -
673 -
674 -=== 2.5.1 Ways to get datalog via LoRaWAN ===
675 -
676 -
677 -Set PNACKMD=1, CPL03-LB will wait for ACK for every uplink, when there is no LoRaWAN network,CPL03-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
678 -
679 -* (((
680 -a) CPL03-LB will do an ACK check for data records sending to make sure every data arrive server.
544 +(((
545 +In the formula above, d is the diameter of light spot; D is detecting range; β is the value of the receiving angle of The LiDAR probe, 3.6°. Correspondence between the diameter of light spot and detecting range is given in Table below.
681 681  )))
682 -* (((
683 -b) CPL03-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but CPL03-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if CPL03-LB gets a ACK, CPL03-LB will consider there is a network connection and resend all NONE-ACK messages.
684 -)))
685 685  
686 -Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
548 +[[image:1654831810009-716.png]]
687 687  
688 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
689 689  
690 -
691 -=== 2.5.2 Unix TimeStamp ===
692 -
693 -
694 -CPL03-LB uses Unix TimeStamp format based on
695 -
696 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
697 -
698 -User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
699 -
700 -Below is the converter example
701 -
702 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
703 -
704 -
705 -So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
706 -
707 -
708 -=== 2.5.3 Set Device Time ===
709 -
710 -
711 -User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
712 -
713 -Once CPL03-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to CPL03-LB. If CPL03-LB fails to get the time from the server, CPL03-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
714 -
715 -(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
716 -
717 -
718 -=== 2.5.4 Poll sensor value ===
719 -
720 -
721 -Users can poll sensor values based on timestamps. Below is the downlink command.
722 -
723 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
724 -|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
725 -|(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
726 -|(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
727 -
728 728  (((
729 -Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
552 +If the light spot reaches two objects with different distances, as shown in Figure 3, the output distance value will be a value between the actual distance values of the two objects. For a high accuracy requirement in practice, the above situation should be noticed to avoid the measurement error.
730 730  )))
731 731  
732 -(((
733 -For example, downlink command [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20220518162852-1.png?rev=1.1||alt="image-20220518162852-1.png"]]
734 -)))
735 735  
736 -(((
737 -Is to check 2021/11/12 12:00:00 to 2021/11/12 15:00:00's data
738 -)))
556 +=== 2.8.3 Notice of usage: ===
739 739  
740 -(((
741 -Uplink Internal =5s，means CPL03-LB will send one packet every 5s. range 5~~255s.
742 -)))
743 743  
559 +Possible invalid /wrong reading for LiDAR ToF tech:
744 744  
745 -== 2.7 Frequency Plans ==
561 +* Measure high reflectivity object such as: Mirror, Smooth ceramic tile, static milk surface, will have possible wrong readings.
562 +* While there is transparent object such as glass, water drop between the measured object and the LiDAR sensor, the reading might be wrong.
563 +* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
564 +* The sensor window is made by Acrylic. Don't touch it with alcohol material. This will destroy the sensor window.
746 746  
747 747  
748 -The CPL03-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
567 +=== 2.8.4  Reflectivity of different objects ===
749 749  
750 -[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
751 751  
570 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:379px" %)
571 +|=(% style="width: 54px;background-color:#D9E2F3;color:#0070C0" %)Item|=(% style="width: 231px;background-color:#D9E2F3;color:#0070C0" %)Material|=(% style="width: 94px;background-color:#D9E2F3;color:#0070C0" %)Relectivity
572 +|(% style="width:53px" %)1|(% style="width:229px" %)Black foam rubber|(% style="width:93px" %)2.4%
573 +|(% style="width:53px" %)2|(% style="width:229px" %)Black fabric|(% style="width:93px" %)3%
574 +|(% style="width:53px" %)3|(% style="width:229px" %)Black rubber|(% style="width:93px" %)4%
575 +|(% style="width:53px" %)4|(% style="width:229px" %)Coal (different types of coal)|(% style="width:93px" %)4~~8%
576 +|(% style="width:53px" %)5|(% style="width:229px" %)Black car paint|(% style="width:93px" %)5%
577 +|(% style="width:53px" %)6|(% style="width:229px" %)Black Jam|(% style="width:93px" %)10%
578 +|(% style="width:53px" %)7|(% style="width:229px" %)Opaque black plastic|(% style="width:93px" %)14%
579 +|(% style="width:53px" %)8|(% style="width:229px" %)Clean rough board|(% style="width:93px" %)20%
580 +|(% style="width:53px" %)9|(% style="width:229px" %)Translucent plastic bottle|(% style="width:93px" %)62%
581 +|(% style="width:53px" %)10|(% style="width:229px" %)Carton cardboard|(% style="width:93px" %)68%
582 +|(% style="width:53px" %)11|(% style="width:229px" %)Clean pine|(% style="width:93px" %)70%
583 +|(% style="width:53px" %)12|(% style="width:229px" %)Opaque white plastic|(% style="width:93px" %)87%
584 +|(% style="width:53px" %)13|(% style="width:229px" %)White Jam|(% style="width:93px" %)90%
585 +|(% style="width:53px" %)14|(% style="width:229px" %)Kodak Standard Whiteboard|(% style="width:93px" %)100%
586 +|(% style="width:53px" %)15|(% style="width:229px" %)(((
587 +Unpolished white metal surface
588 +)))|(% style="width:93px" %)130%
589 +|(% style="width:53px" %)16|(% style="width:229px" %)Glossy light metal surface|(% style="width:93px" %)150%
590 +|(% style="width:53px" %)17|(% style="width:229px" %)stainless steel|(% style="width:93px" %)200%
591 +|(% style="width:53px" %)18|(% style="width:229px" %)Reflector plate, reflective tape|(% style="width:93px" %)>300%
752 752  
753 -= 3. Configure CPL03-LB =
754 754  
594 += 3. Configure LDS12-LB =
595 +
755 755  == 3.1 Configure Methods ==
756 756  
757 757  
758 -CPL03-LB supports below configure method:
599 +LDS12-LB supports below configure method:
759 759  
760 760  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
602 +
761 761  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
604 +
762 762  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
763 763  
764 764  == 3.2 General Commands ==
... ... @@ -767,6 +767,7 @@
767 767  These commands are to configure:
768 768  
769 769  * General system settings like: uplink interval.
613 +
770 770  * LoRaWAN protocol & radio related command.
771 771  
772 772  They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
... ... @@ -774,10 +774,10 @@
774 774  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
775 775  
776 776  
777 -== 3.3 Commands special design for CPL03-LB ==
621 +== 3.3 Commands special design for LDS12-LB ==
778 778  
779 779  
780 -These commands only valid for CPL03-LB, as below:
624 +These commands only valid for LDS12-LB, as below:
781 781  
782 782  
783 783  === 3.3.1 Set Transmit Interval Time ===
... ... @@ -819,226 +819,15 @@
819 819  Example 1: Downlink Payload: 0100001E  ~/~/ Set Transmit Interval (TDC) = 30 seconds
820 820  )))
821 821  * (((
822 -Example 2: Downlink Payload: 0100003C  ~/~/ Set Transmit Interval (TDC) = 60 seconds
666 +Example 2: Downlink Payload: 0100003C  ~/~/ Set Transmit Interval (TDC) = 60 seconds 
823 823  
824 824  
825 825  
826 826  )))
827 827  
828 -=== 3.3.2 Quit AT Command ===
672 +=== 3.3.2 Set Interrupt Mode ===
829 829  
830 830  
831 -Feature: Quit AT Command mode, so user needs to input the password again before using AT Commands.
832 -
833 -(% style="color:blue" %)**AT Command: AT+DISAT**
834 -
835 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:452px" %)
836 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 198px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 99px;background-color:#D9E2F3;color:#0070C0" %)**Response**
837 -|(% style="width:155px" %)AT+DISAT|(% style="width:198px" %)Quit AT Commands mode|(% style="width:96px" %)OK
838 -
839 -(% style="color:blue" %)**Downlink Command:**
840 -
841 -No downlink command for this feature.
842 -
843 -
844 -=== 3.3.3 Get Device Status ===
845 -
846 -
847 -Send a LoRaWAN downlink to ask device send Alarm settings.
848 -
849 -(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
850 -
851 -Sensor will upload Device Status via FPORT=5. See payload section for detail.
852 -
853 -
854 -=== 3.3.4 Enable / Disable Alarm ===
855 -
856 -
857 -Feature: Enable/Disable Alarm for open/close event. Default value 0.
858 -
859 -(% style="color:blue" %)**AT Command:**
860 -
861 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
862 -|(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:278px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0; width:88px" %)**Response**
863 -|(% style="width:154px" %)AT+DISALARM=1|(% style="width:278px" %)End node will only send packets in TDC time.|OK
864 -|(% style="width:154px" %)AT+DISALARM=0|(% style="width:278px" %)End node will send packets in TDC time or status change for door sensor|OK
865 -
866 -(% style="color:blue" %)**Downlink Command:**
867 -
868 -**0xA7 01**  ~/~/  Same As AT+DISALARM=1
869 -
870 -**0xA7 00    ** ~/~/  Same As AT+DISALARM=0
871 -
872 -
873 -=== 3.3.5 Alarm Base on Timeout ===
874 -
875 -
876 -(((
877 -CPL03-LB can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
878 -)))
879 -
880 -
881 -(((
882 -(% style="color:#4f81bd" %)**1. Keep Status: Status to be monitor**
883 -)))
884 -
885 -(((
886 -**Keep Status = 1**: Monitor Close to Open event
887 -)))
888 -
889 -(((
890 -**Keep Status = 0**: Monitor Open to Close event
891 -)))
892 -
893 -
894 -(((
895 -(% style="color:#4f81bd" %)**2. Keep Time: Timeout to send an Alarm**
896 -)))
897 -
898 -(((
899 -Range 0 ~~ 65535(0xFFFF) seconds.
900 -)))
901 -
902 -(((
903 -If** keep time = 0**, Disable Alarm Base on Timeout feature.
904 -)))
905 -
906 -(((
907 -If **keep time > 0**, device will monitor the keep status event and send an alarm when status doesn’t change after timeout.
908 -)))
909 -
910 -
911 -(((
912 -(% style="color:#4f81bd" %)**AT Command**(%%) to configure:
913 -)))
914 -
915 -(((
916 -(% style="color:blue" %)**AT+TTRIG=1,30**(%%)  ~-~-> When the **Keep Status** change from connect to disconnect, and device remains in disconnect status for more than 30 seconds. CPL03-LB will send an uplink packet, the [[Alarm bit>>||anchor="H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
917 -)))
918 -
919 -(((
920 -(% style="color:blue" %)**AT+TTIG=0,0 **(%%) ~-~-> Default Value, disable timeout Alarm.
921 -)))
922 -
923 -
924 -(((
925 -(% style="color:#4f81bd" %)**Downlink Command**(%%) to configure:
926 -)))
927 -
928 -(((
929 -**Command: 0xA9 aa bb cc**
930 -)))
931 -
932 -(((
933 -**A9: **Command Type Code
934 -)))
935 -
936 -(((
937 -**aa: **status to be monitored
938 -)))
939 -
940 -(((
941 -**bb cc: **timeout.
942 -)))
943 -
944 -
945 -(((
946 -If user send 0xA9 01 00 1E: equal to AT+TTRIG=1,30
947 -)))
948 -
949 -(((
950 -Or
951 -)))
952 -
953 -(((
954 -0xA9 00 00 00: Equal to AT+TTRIG=0,0. Disable timeout Alarm.
955 -)))
956 -
957 -
958 -=== 3.3.6 Clear Flash Record ===
959 -
960 -
961 -Feature: Clear flash storage for data log feature.
962 -
963 -(% style="color:blue" %)**AT Command: AT+CLRDTA**
964 -
965 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
966 -|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 169px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 174px;background-color:#D9E2F3;color:#0070C0" %)**Response**
967 -|(% style="width:157px" %)AT+CLRDTA|(% style="width:169px" %)Clear flash storage for data log feature.|Clear all stored sensor data… OK
968 -
969 -(((
970 -(% style="color:blue" %)**Downlink Command:**
971 -)))
972 -
973 -(((
974 -* **Example**: 0xA301  ~/~/  Same as AT+CLRDTA
975 -)))
976 -
977 -
978 -
979 -=== 3.3.7 Set trigger mode ===
980 -
981 -
982 -Feature: Set the trigger interrupt mode.
983 -
984 -(% style="color:blue" %)**AT Command: AT+TTRMOD**
985 -
986 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:495px" %)
987 -|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 246px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 92px;background-color:#D9E2F3;color:#0070C0" %)**Response**
988 -|(% style="width:157px" %)(((
989 -AT+TTRMOD=1
990 -)))|(% style="width:156px" %)Count and trigger from open to close (rising edge)|(% style="width:89px" %)(((
991 -(((
992 -OK
993 -)))
994 -)))
995 -|(% style="width:157px" %)(((
996 -AT+TTRMOD=0
997 -)))|(% style="width:156px" %)Count and trigger from close to open (falling edge)|(% style="width:89px" %)(((
998 -OK
999 -)))
1000 -
1001 -(% style="color:blue" %)**Downlink Command:**
1002 -
1003 -* **Example**: 0xA401  ~/~/  Same as AT+ TTRMOD =1
1004 -
1005 -=== 3.3.8 Set the calculate flag ===
1006 -
1007 -
1008 -Feature: Set the calculate flag
1009 -
1010 -(% style="color:blue" %)**AT Command: AT+CALCFLAG**
1011 -
1012 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:461px" %)
1013 -|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1014 -|(% style="width:158px" %)AT+CALCFLAG =1|(% style="width:192px" %)Set the calculate flag to 1.|(% style="width:109px" %)OK
1015 -|(% style="width:158px" %)AT+CALCFLAG =2|(% style="width:192px" %)Set the calculate flag to 2.|(% style="width:109px" %)OK
1016 -
1017 -(% style="color:blue" %)**Downlink Command:**
1018 -
1019 -* **Example**: 0XA501  ~/~/  Same as AT+CALCFLAG =1
1020 -
1021 -=== 3.3.9 Set count number ===
1022 -
1023 -
1024 -Feature: Manually set the count number
1025 -
1026 -(% style="color:blue" %)**AT Command: AT+SETCNT**
1027 -
1028 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:479px" %)
1029 -|=(% style="width: 160px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 223px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 96px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1030 -|(% style="width:160px" %)AT+ SETCNT =0|(% style="width:221px" %)Set the count number to 0.|(% style="width:95px" %)OK
1031 -|(% style="width:160px" %)AT+ SETCNT =100|(% style="width:221px" %)Set the count number to 100.|(% style="width:95px" %)OK
1032 -
1033 -(% style="color:blue" %)**Downlink Command:**
1034 -
1035 -* **Example**: 0xA6000001  ~/~/  Same as AT+ SETCNT =1
1036 -
1037 -* **Example**: 0xA6000064  ~/~/  Same as AT+ SETCNT =100
1038 -
1039 -=== 3.3.10 Set Interrupt Mode ===
1040 -
1041 -
1042 1042  Feature, Set Interrupt mode for PA8 of pin.
1043 1043  
1044 1044  When AT+INTMOD=0 is set, PA8 is used as a digital input port.
... ... @@ -1070,77 +1070,77 @@
1070 1070  
1071 1071  * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
1072 1072  
1073 -=== 3.3.11 Set Power Output Duration ===
706 += 4. Battery & Power Consumption =
1074 1074  
1075 1075  
1076 -Control the output duration 5V . Before each sampling, device will
709 +LDS12-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
1077 1077  
1078 -~1. first enable the power output to external sensor,
711 +[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
1079 1079  
1080 -2. keep it on as per duration, read sensor value and construct uplink payload
1081 1081  
1082 -3. final, close the power output.
714 += 5. OTA Firmware update =
1083 1083  
1084 -(% style="color:blue" %)**AT Command: AT+5VT**
1085 1085  
1086 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1087 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1088 -|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
1089 -OK
1090 -|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
717 +(% class="wikigeneratedid" %)
718 +User can change firmware LDS12-LB to:
1091 1091  
1092 -(% style="color:blue" %)**Downlink Command: 0x07**
720 +* Change Frequency band/ region.
1093 1093  
1094 -Format: Command Code (0x07) followed by 2 bytes.
722 +* Update with new features.
1095 1095  
1096 -The first and second bytes are the time to turn on.
724 +* Fix bugs.
1097 1097  
1098 -* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
726 +Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/ph4uyz0rchflrnw/AADr1f_5Sg30804NItpfOQbla?dl=0]]**
1099 1099  
1100 -* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
728 +Methods to Update Firmware:
1101 1101  
1102 -= 4. Battery & Power Consumption =
730 +* (Recommanded way) OTA firmware update via wireless:  **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
1103 1103  
732 +* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
1104 1104  
1105 -CPL03-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
734 += 6. FAQ =
1106 1106  
1107 -[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
736 +== 6.1 What is the frequency plan for LDS12-LB? ==
1108 1108  
1109 1109  
1110 -= 5. OTA Firmware update =
739 +LDS12-LB use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
1111 1111  
1112 1112  
1113 -(% class="wikigeneratedid" %)
1114 -User can change firmware CPL03-LB to:
742 += 7. Trouble Shooting =
1115 1115  
1116 -* Change Frequency band/ region.
744 +== 7.1 AT Command input doesn't work ==
1117 1117  
1118 -* Update with new features.
1119 1119  
1120 -* Fix bugs.
747 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:blue" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:blue" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1121 1121  
1122 -Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
1123 1123  
1124 -Methods to Update Firmware:
750 +== 7.2 Significant error between the output distant value of LiDAR and actual distance ==
1125 1125  
1126 -* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
1127 1127  
1128 -* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
753 +(((
754 +(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
755 +)))
1129 1129  
1130 -= 6. FAQ =
757 +(((
758 +Troubleshooting: Please avoid use of this product under such circumstance in practice.
759 +)))
1131 1131  
1132 -== 6.1  AT Commands input doesn't work ==
1133 1133  
762 +(((
763 +(% style="color:blue" %)**Cause ②**(%%)**: **The IR-pass filters are blocked.
764 +)))
1134 1134  
1135 -In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
766 +(((
767 +Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter.
768 +)))
1136 1136  
1137 1137  
1138 -= 7. Order Info =
771 += 8. Order Info =
1139 1139  
1140 1140  
1141 -Part Number: (% style="color:blue" %)**CPL03-LB-XXX**
774 +Part Number: (% style="color:blue" %)**LDS12-LB-XXX**
1142 1142  
1143 -(% style="color:red" %)**XXX**(%%): The default frequency band
776 +(% style="color:red" %)**XXX**(%%): **The default frequency band**
1144 1144  
1145 1145  * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
1146 1146  
... ... @@ -1158,12 +1158,12 @@
1158 1158  
1159 1159  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1160 1160  
1161 -= 8. ​Packing Info =
794 += 9. ​Packing Info =
1162 1162  
1163 1163  
1164 1164  (% style="color:#037691" %)**Package Includes**:
1165 1165  
1166 -* CPL03-LB LoRaWAN Pulse/Contact Sensor
799 +* LDS12-LB LoRaWAN LiDAR ToF Distance Sensor x 1
1167 1167  
1168 1168  (% style="color:#037691" %)**Dimension and weight**:
1169 1169  
... ... @@ -1175,7 +1175,7 @@
1175 1175  
1176 1176  * Weight / pcs : g
1177 1177  
1178 -= 9. Support =
811 += 10. Support =
1179 1179  
1180 1180  
1181 1181  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
image-20230612170349-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +164.2 KB
Content
image-20230612170943-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +86.4 KB
Content
image-20230612171032-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +86.4 KB
Content
image-20230613100900-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +184.0 KB
Content
image-20230613102426-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +89.3 KB
Content
image-20230613102459-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +89.3 KB
Content
image-20230613133647-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +213.6 KB
Content
image-20230613133716-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +165.8 KB
Content
image-20230613140115-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +92.1 KB
Content
image-20230613140140-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +92.1 KB
Content
image-20230613143052-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +21.8 KB
Content
image-20230613143125-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +24.7 KB
Content
image-20230614153353-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +112.1 KB
Content
image-20230614162334-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +88.3 KB
Content
image-20230614162359-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +88.3 KB
Content